The URL can be used to link to this page

Home My WebLink AboutProduct Approval i 9AMI l F # MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT Of REGULATORY AND ECONOMIC RESOURCES(RER) 11805 SW 26 Street. Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T(786)315-2590 F(786)315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy Iko Industries Ltd. 40 Hansen Rd. S. Brampton, Ontario CANADA L6W3H4 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The documentation submitted has been reviewed and accepted by Miami-Dade County RER - Product Control Section to be used in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ), This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (in Miami-Dade County) and/or the AHJ (in areas other than Miami-Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AI-IJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Cambridge, Cambridge HD, and Biltmore AR Asphalt Shingles LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA No.]4-0603.02 and consists of pages 1 through 4. The submitted documentation was reviewed by Gaspar J Rodriguez. z NOA No.: 16-0329.13 MIAMI•DADECOUNTY Expiration Date: 05/05/21 e Approval Date: 04/21/16 Page 1 of 4 . ROOFING ASSEMBLY APPROVAL Roofing Asphalt Shingles Laminate Deck Tvpe. Wood SCOPE This approves oroofing system using Cambridge AR,Cambridge HD, and Biltmore ARasphalt shingles manUfaCtUred by IKO IndUstries Ltd. as described in Section 2 of his Notice of Acceptance. PRODUCT DESCRIPTION Product Dimensions Test Specifications Product Description Cambridge 13 1/4" u40 '/o" Tf\3 110 & heavy weight, fiberglass reinforced |ao)inut�aaphu|1yhin�|n. Manufacturing Location #/. l 3 Cambridge HD 13 //4" x4 0 7/8'' TAS } }0 /\ heavy weight, fiberglass reinforced ��mu/�c/or/�� 000//on #/. 2. � laminate asphalt shingle. Biltmore AR 13 '/ " x40 '/x" TAS \ \O /\ heavy weight, fiberglass reinforced Allanufocluring loxotilaminate unnhukshingle. on #/. 2 --,-- =' MANUFACTURING LOCATION I. Kankakee, IL 2. Wilmington, DE 3. Sv|uouugu /\[ EVIDENCE SUBMITTED Test Ap_ency Test Identifier Test Name/Repor Date PRI Consiruo\ion Materials Inc. |k|O'050'02'01 TAS 100 12/21/09 lK0'076'02'01 T&3 100 03/21/12 |KO-| \4'O2'0| TAS |OO 09/25/14 |KD-099'02'01 TAS |OO 05/12/14 [|{O-090-02-01 ASTM D34b2 09/27/13 ||{O-095-02'01 ASTM D34b2 09/27/13 }K(}-12}-02-01 ASTM D3462 09/25/14 ||{0-100'02'01 ASTM D3\6| (TAS-107) 05/21/14 [l(0-| |5-U2-O! ASTM D3}0| (TAS-107) 09/25/14 FM Approvals 3041689 ASTM D3402 02/23/11 3036971 ASTM DJlh| (TAS-107) 01/04/09 3042673 ASTM 2lO8 04/12/11 MO6Nu: l6-03%u13 Expiration Date: 05/05/21 Approval Date: 04/21/16 ^ LIMITATIONS 1. Fire classification is not part of this acceptance; refer to a current Approved.Roofing Materials Directory for fire ratings of this product. 2. Shall not be installed on roof mean heights in excess of 33 ft. 3. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rile 61G20-3 of the Florida Administrative Code. INSTALLATION I. Shingles shall be installed in compliance with Roofing Application Standard RAS 115. 2. Flashing shall be in accordance with Roofing Application Standard RAS 115 3. The manufacturer shall provide clearly written application instructions. 4. Exposure and course layout shall be in compliance with Detail W, attached. 5. Nailing shall be in compliance with Detail 'B', attached. LABELING 1. Shingles shall be labeled with the Miami-Dade Seal as seen below, or the wording"Miami-Dade County Product Control Approved". DECOUNTY BUILDING PERMIT REQUIREMENTS 1. Application for building permit shall be accompanied by copies of the following: 1.1 This Notice of Acceptance. 1.2 Any other documents required by the Building Official or the applicable code in order to properly evaluate the installation of this systern. NOA No.: 16-0329.13 MIAWDAD'E COUNTY0 COUNTYExpiration Date: 05/05/21 Approval Date: 04/21/16 Page 3 of 4 DETAIL A CAMBRIDGE, CAMBRIDGE HD, BILTMORE AR COURSE LAYOUT _-EDGE OF ROUP Note:Roofing Cement not shown in this layout. This drawing is lix course layout only. See Detail B -' - for nailing and cement placement details. -I4 THIRD COURSE SECONDCOURSE -- 4 - I ----- %Fa •_ FIRST COURSE / l DETAIL D CAMBRIDGE, CAMBRIDGE HD,BILTMORE AR 40 ?n ti 13 3„ 4 �n -- S I8" EXPOSURE 1 END OF THIS ACCEPTANCE MIAMI•DADE COUNTY NOA No.: 16-0329.13 Expiration Date: 05/05/21 Approval Date: 04/21/16 Page 4 of 4 al od P'IAMI,0AE)E F MIAMI-DADE COUNTY PRODUCT CONTROL SECTION I 1805 SW 26 Street,Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) Miami,Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T(786)315-2590 F(786)31525-99 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economv CertainTeed Corporation 18 Moores Road Malvern, PA 19355 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). . This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet.the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: CertainTeed Modified Bitumen Roofing Systems over Wood Decks. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA \vill occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA #14-0224.03) and consists of pages 1 through 42. The submitted documentation was reviewed by Alex Tigera. NOA No.: 14-0529.02 W.MIAMI-DADE COUNTY Expiration Date: 06/19/18 Approval Date: 09/24/15 Page 1 of 42 ROOFING SYSTEM APPROVAL Category: Roofing Sub-Categoi:3L. Modified Bitumen Material: APP/SBS Deck Type: Wood Maximum Design Pressure: -127.5 psL TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Product Dimensions Specification Description All Weather/Empire Base 39 '/s" x 65'10"; ASTM D 4601, Type Asphalt coated, fiberglass reinforced Sheet Roll weight: 70 lbs. II base sheet. (2 squares) UL Type G2 Flexiglas Base Sheet -')9 '/8" x 98'9"; Roll ASTM D 4601, Type Modified Bitumen coated fiberglass weight: 90 lbs. 11 base sheet. (3 squares) UL Type G2 Flintlastic Base 20 39 '/8" x 49' 6"; Roll ASTM D 6163, Modified Bitumen coated fiberglass weight: 90 lbs. Grade S, Type I base sheet. (1.5 squares) Flintglas Ply Sheet Type IV 39 '/s" x 1647"; Roll ASTM D 2178, Type Fiberglass, asphalt impregnated ply sheet. weight: 38 lbs. IV (5 squares) UL Type GI Flintglas Premium Ply Sheet 39 '/8" x 164'7"; Roll ASTM D 2178, Type Fiberglass, asphalt impregnated ply Type VI weight: 40 lbs. V1 sheet. (5 squares) UL Type G 1 Flintlastic STA 39 3/8" x 32' 10"; Roll ASTM D 6222, Smooth surfaced APP Modified weight: 87 lbs. Grade S, Type I Bitumen membrane with non-woven (I square) polyester mat reinforcement for torch application. Flintlastic GTA 39 3/8" x 32' 10"; Roll ASTM D 6222, Granule surfaced APP Modified weight: 105 lbs. Grade G, Type I Bitumen membrane with non-woven (1 square) polyester mat reinforcement for torch application. Flintlastic GTA-FR 39 3/8" x 32' 10"; Roll ASTM D 6222, Granule surfaced APP Modified weight: 105 lbs. Grade G, Type I Bitumen membrane with non-woven (I square) polyester mat reinforcement for torch application. Flintlastic GMS 39 '/8" x 32' 10"; Roll ASTM D 6164, Granule surfaced SBS Modified weight: 94 lbs. Grade G, Type I Bitumen membrane with non-woven (I square) polyester mat reinforcement for mop application. NOA No.: 14-0529.02 MIAMI•DADE COUNTY Expiration Date: 06/19/18 Approval Date: 09/24/15 Page 2 of 42 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Product Dimensions Specification Description Flintlastic GTA CoolStar 39 '/8" x 32' 10"; Roll ASTM D 6222, Granule surfaced APP Modified weight: 106 lbs. Grade G, Type I Bitumen membrane with non-woven (I square) polyester mat reinforcement for torch application. Covered with reflective CoolStar Coating. Flintlastic GTA-FR CoolStar 39 3/8" x 32' 10"; Roll ASTM D 6222, Granule surfaced APP Modified weight: 106 lbs. Grade G, Type I Bitumen membrane with non-woven (I square) polyester mat reinforcement for torch application. Covered with reflective CoolStar Coating. Flintlastic GMS CoolStar 39 3/s" x 32' I0", Roll ASTM D 6164, Granule surfaced SBS Modified weight: 97 lbs. Grade G, Type I Bitumen membrane with non-woven (1 square) polyester mat reinforcement for mop application. Covered with reflective CoolStar Coating. Flintlastic Premium GMS 39 3/8" x 32' 10"; Roll ASTM D 6164, Granule surfaced SBS Modified CoolStar weight:103 lbs. Grade G, Type 11 Bitumen membrane with non-woven (1 square) polyester mat reinforcement for mop application. Covered with reflective CoolStar Coating. Flintlastic FR-P CoolStar 39 3/8" x 32' 10"; Roll ASTM D 6164, Fire resistant, granule surfaced SBS weight: 103 lbs. Grade G, Type I Modified Bitumen Membrane with (I square) non-woven polyester mat reinforcement for mop application. Covered with reflective CoolStar Coating. Flintlastic Premium FR-P 39 3/s" x 32' 10"; Roll ASTM D 6164, Fire resistant, granule surfaced SBS CoolStar weight: 103 lbs. Grade G, Type 11 Modified Bitumen Membrane with (1 square) non-woven polyester mat reinforcement for mop application. Covered with reflective CoolStar Coating. Flintlastic Ultra Poly SMS 39 3/8" x 32' 10"; Roll ASTM D 6164, Smooth surfaced SBS Modified Base Sheet weight: 90 lbs. (I Grade S, Type I Bitumen Membrane with non-woven squares) polyester mat reinforcement for mop applications. Glasbase Base Sheet 36" x 98' 9'•; Roll ASTM D 4601, Type Asphalt coated, fiberglass base sheet. weight: 75 lbs. 11, (3 squares) UL Type G2 NOA No.: 14-0529.02 QMIAMMI-DMADEMCOMUNTY Expiration Date: 06/19/18 Approval Date: 09/24/15 Page 4 of 42 _l TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Product Dimensions Specification Description Flintlastic Premium GMS 39 3/8" x 32' 10". Roll ASTM D 6164, Granule surfaced SBS Modified weight: 101 lbs. Grade G, Type II Bitumen membrane with non-woven (1 square) polyester mat reinforcement for mop application. Flintlastic FR-P 39 3/8" x 32' 10"; Roll ASTM D 6164, Fire resistant, granule surfaced SBS weight: 101 lbs. Grade G, Type I Modified Bitumen Membrane with (I square) non-woven polyester mat reinforcement for mop application. Flintlastic Premium FR-P 39 3/8" x 32' 10"; Roll ASTM D 6164, Fire resistant, granule surfaced SBS weight: 101 lbs. Grade G, Type II Modified Bitumen Membrane with (1 square) non-woven polyester mat reinforcement for mop application. Flintlastic FR Dual Cap 39 3/8" x 32' 10", Roll ASTM D 6162, Granule surfaced SBS modified weight: 103 lbs. Grade G, Type I bitumen membrane with a nonwoven (1 square) polyester/fiberglass composite mat reinforcement for use in cold or mop applications. Flintlastic FR Cap 30 39 3/s" x 32' 10"; Roll ASTM D 6163, Fire resistant, granule surfaced SBS weight: 86 lbs. Grade G, Type I Modified Bitumen membrane with (I square) fiberglass rnat reinforcement for mop applications. Flintlastic FR Cap 30 T 39-3/8" x 32' 10"; Roll ASTM D 6163, Granule surfaced SBS Modified weight: 100 lbs. Grade G, Type I Bitumen membrane with fiberglass (1 square) mat reinforcement for torch application. Flintlastic Base 20 T 39-3/8" x 33% Roll ASTM D 6163, Modified Bitumen, coated fiberglass Weight: 81 lbs. Grade S, Type I base sheet for torch application. (I square) Flintlastic FR Cap 30 CoolStar 39 3/s" x 32' 10"; Roll ASTM D 6163, Fire resistant, granule surfaced SBS weight: 88 lbs. Grade G, Type I Modified Bitumen membrane with (I square) fiberglass mat reinforcement for mop applications. Covered with reflective CoolStar Coating. Flintlastic FR Cap 30 T 39 3/8" x 32' 10". Roll ASTM D 6163, Fire resistant, granule surfaced SBS CoolStar weight: 102 lbs. Grade G, Type I Modified Bitumen membrane with (I square) fiberglass mat reinforcement for mop applications. Covered with reflective CoolStar Coating. NOA No.: 14-0529.02 MIAMI•DADE COUNTY Expiration Date: 06/19/18 Approval Date: 09/24/15 Page 3 of 42 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE I Test Product Product Dimensions Specification Description Flintlastic Poly SMS Base 39 '/8" x 64' 3"; Roll ASTM D 4601, Modified Bitumen coated polyester Sheet weight: 90 lbs. Grade S, Type II base sheet. (2 squares) UL Type G2 Yosemite Venting Base Sheet 39 '/s" x 32'10". Roll ASTM D 3909 Mineral Surfaced fiberglass reinforced weight: 85 lbs. ASTM D 4897, Type buffer sheet. (I square) 11 UL Type G3 Flintlastic APP Base T 39 '/s" x 65' 4"; Roll ASTM D 6509 Modified Bitumen coated fiberglass weight: 100 lbs. base sheet. (2 squares) Flintlastic Ultra Glass SA 39 3/8" x 3)Y1 1"; Roll ASTM D 1970 Self-adhering, fiberglass reinforced, weight: 73 lbs. SBS modified bitumen base/ply sheet. (I square) Black DiamondTm Base Sheet 36" x 687'; Roll ASTM D 1970 Self-adhering fiberglass reinforced weight: 78 lbs. modified bitumen base sheet (2 squares) APPROVED INSULATIONS: I TABLE 2 Product Name Product Description Manufacturer (With Current NOA) FlintBoard ISO Polyisocyanurate foam insulation CertainTeed Corporation FlintBoardi-I ISO Polyisocyanurate foam insulation CertainTeed Corp. ACFoam -II Polyisocyanurate foam insulation Atlas Roofing Corp. High Density Wood Fiberboard Wood fiber insulation board Generic Perlite Insulation Pet-lite insulation board Generic DensDeck, DensDeck Prime Water resistant gypsum board Georgia Pacific Gypsum LLC H-Shield Polyisocyanurate foam insulation Hinter Panels LLC ENRGY 3 Polyisocyanurate foam insulation Johns Manville Corp. ENRGY 3 25 PSI Polyisocyanurate foam insulation Johns Manville Corp. Multi-Max FA-3 Polyisocyanurate foam insulation RMax Operating, LLC SECUROCK Gypsum-Fiber Roof Board homogenous fiber reinforced USG Corp. NOA No.: 14-0529.02 MIAMI•DADE COUNTYIN o 14111ow Expiration Date: 06/19/18 Approval Date: 09/24/15 Page 5 of 42 APPROVED FASTENERS: TABLE 3 Fastener Product Product Manufacturer Number Name Description Dimensions (With Current NOA) 1. Trufast#12 DP Fastener Insulation fastener for wood various Altenloh, Brinch & Co. U.S., and steel decks Inc. 2. Trufast 3" Metal Galvalume steel plate 3" round Altenloh, Brinch & Co. U.S., Insulation Plate Inc. 3. FlintFast#12 Coated, carbon steel screw various CertainTeed Corp. 4. FlintFast 3" Insulation Galvalume AZ50 steel plate 3" round CertainTeed Corp. Plate 5. FlintFast #14 Insulation fastener for wood various CertainTeed Corp. and steel decks 6. Simplex MAXX Cap Polymer fastner 1" long Simplex Nails, Inc. 7. OMG #12 Standard Insulation fastener for wood various OMG, Inc. Roofgrip and steel. 8. OMG 3" Galvanized Steel GalvalLinle stress plate 3" round OMG, Inc. Plates 9. Trufast #14 HD Fastener Insulation fastener for wood various Altenloh, Brinch & Co. U.S., and steel decks Inc. 10. OMG Heavy Duty Insulation and membrane Various OMG, Inc. fastener 11. OMG 3 in. Round Metal Galvalume AZ50 steel plate 3" round OMG, Inc. Plates 12. ACCUtTrac Hextra Carbon steel fastener Various OMG, Inc. 13. AccuTrac Plates Galvalume stress plate. 3" square OMG, Inc. 14. ACCUTrac Flat Bottom A2-SS aluminized steel plate 3" square OMG, Inc. Plates NOA No.: 14-0529.02 MIAMI•DADE COUNTY Expiration Date: 06/19/18 Approval Date: 09/24/15 Page 6 of 42 APPROVED SURFACING/COATING OPTIONS: TABLE 4 Chosen components must be applied according to manufacturer's application instructions. Any coating, listed below, used as a surfacing, must be listed within a current NOA. System Number Manufacturer Application 1. Generic Gravel applied at 400 lbs/sq., adhered with flood coat of asphalt at 60 lbs/sq. 2. Generic Slag applied at 300 lbs/sq., adhered with flood coat of asphalt at 60 lbs/sq. 3. Karnak Corp. Karnak (#97 AF) Fibrated Aluminum Roof Coating applied at an application rate of 1.5 gal/sq. 4. CertainTeed Corp. FlintCoat A-150 applied at an application rate of 1.5 gal/sq. 5. Gardner Asphalt Corp. APOC#212 Fibered Aluminum Roof Coating applied at an application rate of 1.5 gal/sq. 6. Gardner Asphalt Corp. APOC 4400 SLInbrite applied at an application rate of 3 gal./sq. NOA No.: 14-0529.02 jCM1:AM:1-DADE COUNTYR! Expiration Date: 06/19/18 BMW Approval Date: 09/24/15 Page 7 of 42 EVIDENCE SUBMITTED: Test Agency/Identifier Name Report Date Factory MUtUal Research Corp. FM 4470 3Y8A l.AM 03/23/96 FM 4470 OD3A3.AM 04/04/97 FM 4470 2DOAO.AM 12/23/98 FM 4470 1 D7A4.AM 11/09/98 FM 4470 3039046 06/15/10 FM 4470 3048520 09/19/13 Underwriters Laboratories, Inc. UL 790 R11656 01/11/13 United States Testing Company ASTM D 5147 97457-4 06/03/88 ASTM D 5147 97-457-2R 12/02/87 Momentum Technologies, Inc. ASTM D 4601 AMIGM 09/05/08 ASTM D6164 AX31 G8F 06/05/09 ASTM D6222 AX31 G8G 06/05/09 ASTM D 3909/ D 4897 AX31 G8C 09/05/08 TrinitylERD TAS 114(J) 3504.06.01-1 06/05/01 TAS 114(J) 3507.08.99-1 04/18/01 TAS 1 17 (B) 3503.10.06 10%10/06 TAS 117 (B) 06490.04.07-RI 06/27/07 TAS 1 14 (H) Letter 04/05/06 TAS 114 3533.01.06 01/06/06 TAS 114 3521.07.04 07/29/04 TAS 117 (B)/ASTM D 6862 C8500SC.11.07 11/30/07 TAS 114 C8370.08.08 08/19/08 ASTM Physical Properties C I 0080.09.08-R4 03/25/10 ASTM D6164/D4798 C31410.01.11-2 01/10/11 ASTM D4601 C40050.09.12-1 09/28/12 ASTM D1970 C40050.09.12-2 09/28/12 ASTM D5147/D4798 C31410.10.10-R1 11/01/12 ASTM D5147/D4798 C31410.01.1 1-1-R 1 11/01/12 ASTM D1876 C35460.05.11 06/16/11 ASTM D1876, TAS 114 (H), C42110.08.12 08/13/12 TAS 117 (B) FM 4474/TAS 1 14 C39670.08.12 08/20/12 TAS 117B C35500.02.11 02/09/11 ASTM D4798 01410.01.11-2A-R] 02/21/13 ASTM D4798 C31410.12.13 12/05/13 ASTM D6222 C40050.12.13-R1 12/31/13 TAS 1 17, TAS 114 C30310.12.09-R1 03/07/14 ASTM DI 876, TAS 114 (H), C45620.03.14 03/27/14 FM 4474 ASTM D1876, TAS 114 (H), C47320.03.14-R1 04/01/15 FM 4474 PRI Construction Materials ASTM D6163 CTC-032-02-01 01/22/08 Technologies LLC ASTM D6163 CTC-066-02-01 08/09/11 ASTM D6222 CTC-070-02-01 08/09/11 DE OUNTY NOA No.: 14-0529.02 MIAMI•DAC Expiration Date: 06/19/18 Approval Date: 09/24/15 Page 8 of 42