The URL can be used to link to this page

Home My WebLink AboutProduct Approval i EXTERIOR RESEARCH&DESIGN, I.I.C. Certificate of Authorization#9503 T�I�I� 353 CHRISTIAN STREET,UNIT#13 JERD OXFORD,CT 06478 PHONE:(203)262-9245 FAX:(203)262-9243 EVALUATION REPORT Owens Corning Evaluation Report 037940.02.12-117 One Owens Corning Parkway FL10674-1112 Toledo,OH 436591 Date of Issuance:02/06/2012 Revision 7: 04/18/2016 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code sections noted herein. DESCRIPTION: Owens Corning Asphalt Roof Shingles I LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such t;me as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity IERD Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 8. I Prepared by: :t. �QaQS `s�?/r�4,�, Ile j!�,' =C9ttC•r±j The facsimile seal appearing was authorized by Robert Nieminen, Robert J.M.Nieminen,P.E. �A,s'': �•••' :; f.1js'rpl�al r�. P.E.on 04/18/2016.This does not serve as an electronically signed Florida Registration No.59166 Florida DCA ANE1983 "'��u`tst�ss document.Signed,sealed hardcoples have been transmitted to the Product Approval Administrator and to the named client CERTIFICATION OF INDEPENDENCE: PENDENCE: 1. TrinitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Trinity l ERD is1not owned,operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the . product. 5. This is a building code evaluation. Neither Trinity lERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained specifically for that purpose. i I r I i TRINI1Y iER® ROOFING SYSTEMS EVALUATION: 1. SCOPE: t Product Category: Roofing Sub-Category: Asphalt Shingles Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated compliance'with the following sections of the Florida Building Code and Florida Building Code, Residential Volume through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations/Conditions of Use set forth herein. 2. STANDARDS: Section Property Standard Year 1507.2.5,R905.2.4 Physical Properties ASTM D3462 2009 1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2009 1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2008 3. REFERENCES: Entity Examination Reference Date UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007 UL LLC(CER9626) Physicals&Wind Resistance 20120516-112453 05/16/2012 UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006 UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012 UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014 UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014 UL LLC(TST9628) Physical Properties Classification letter 02/13/2014 UL LLC(TST9628) Physical Properties Classification letter 10/02/2015 Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various UL LLC (QUiA9625) Quality Control Service Confirmation,R2453 Exp.08/20/2017 4. PRODUCT DESCRIPTION: 4.1 Asphalt Shingles: 4.1.1 Classic and Supreme'are fiberglass reinforced,3-tab asphalt roof shingles. 4.1.2 Berkshire'are fiberglass reinforced,4-tab asphalt roof shingles. i 4.1.3 Devonshire'""are fiberglass reinforced,5-tab asphalt roof shingles. 4.1.4 Duration', TruDefinition' Duration', Duration' Premium Cool, TruDefinition' Duration' Designer Color Collection, TruDefinition'Oakridge, Oakridge' and WeatherGuard' HP are fiberglass reinforced, laminated Zkslhalt roof shingles. 4.2 hire' Hip & Ridge Shingles, High Ridge, WeatherGuard' HP Hip & Ridge Shingles, ProEdge Hip & Ridge Shingles and DuraRidgel Hip&Ridge Shingles are fiberglass reinforced, hip and ridge asphalt roof shingles. 4.3 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles. S. LIMITATIONS: 5.1 This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used fir permitting or design guidance unless retained specifically for that purpose. 5.2 Th'is Evaluation Report is not for use in the HVHZ. 5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire ratings of this product. I Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-117 Certificate of Authorization#9503 F1.10674-1112 Revision 7:04/18/2016 Page 2 of 8 i TRINITY I ER® 5.4 Wind Classification: 5.4.1 All Owens Corning shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for usel in all wind zones up to Vasd= 150 mph (V„it= 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 4 5.4.2 All Owens Corning hip&ridge shingles,Starter Strip Shingle and Starter Strip Plus noted herein are Classified In accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the shingles are acceptable for use in all wind zones up to Vasd=150 mph (Vr,it=194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.3 Classification by ASTM D7158 applies to exposure category B or C and a building height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. 5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations. 5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building Code and F.A.C. Rule 61G20-3. 6. INSTALLATION: 6.1 Underlayment: i 6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product Approval,or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3. 6.2 Asphalt Shingles: 6.2.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using minimum four (4) nails per shingle in accordance with FBC Sections 1507.2 or R905.2, with the following exceptions: Berkshire®shingles require minimum five(5)nails per shingle. WeatherGuarde HP shingles require minimum six(6)nails per shingle. Devonshire TM shingles require minimum six(6)nails per shingle. Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip. Refer to Owens Corning published information on wind resistance and installation limitations. 6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required. See figures below for details. 6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus: Feltunderlayment Deck Fekundedayment Dads SeFedhered werthedockS Self-adhered underleyment WeatherLocka underiayment Drips Drip edge [:dg6� Drip edge edge �. located ' Nails located 2°.3°from cave 2=3"from eave Install fust Self-sealing adhesive Installi54e�ng odAezive Starter Strip positioned along eave th �d r Strip Pin positoned along eave shingle with 6"removed Stoner Plus eaves and rakes 1/4-3/4- Starter Strip shingle overhangs eaves and rakes d='/i" P overhangs Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization#9503 FL10674-1112 j Revision 7:04/18/2016 Page 3 of 8 I i I 1 JTRINI-rYIERD 6.2.6 Minimum Nailing—Classic®&Supreme: Normal Mansard or Area para Normal Mansard or Area pare liYlnd Areas Hlgfi tend n desvenea yWind Areas Hlgh Wind tfesystres y Area pan viontos normales Anas vientos fus'us Area porn vientos nonmeies Areas vientos ft= 1•tt• (A} �r1 r (B z' r u (AI. tit /" 1" z• (B} 2- r S"Expo'sure 6 618"Exposure Erp Islel6n Erposiimn 6.2.7 Mi�limum Nailing—Berkshire®: Sealant strip Sealant strip La tlr+ds sdadar La*a do sellador WIN Q yi 9-vt,. .. 911 9 Yf } "ow- 8 rh" S Vi 8 6'e" 1 Op r r r...__ Standard Fastening Pattern 6-Nail Fastening Pattern i I i Sealant sirlp La Pira de salladar ' r,evr svt a 1" r." Asphad roofngoament Ceineriro de techo da WOO Mansard or Steep Slope Fastening Pattern I I Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization 119503 F1.10674-1112 Revision 7:04/18/2016 Page 4 of 8 I F-fi -iY ERD f 6.2.8 Minlimum Nailing—Devonshire TM: I 8" 8" 7" �. N 4P dams Nails ••_••� ry r e. r 5318'exposure Sealant location ' Exposiei6n de 5.518 pull; Ubisadiin del selledor S • 6: Ten 11"Spots of Asphalt Roof Cement Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern 6.2.9 Mil imum Nailing—Duration®,TruDefinition® Duration, Duration® Premium Cool &TruDefinition® Duration® Designer Color Collection: 4-Nell Fastening Pattern 6-Nail Fastening Pattern surelmmsmingarearaatn S.Ur wsAtastenlrtp meawWm Na. Mk Tjpleal i• tr tr t- t^ tr tr r 6118^6-fi18• LE Standard Fastening Pattern 6-Nail Fastening Pattern Fastening for Slopes Greater Than 21:12 bunWIM7hfbnlne m width NaU.lyPlwl T tY I I 1Y 1" I s.tra"s•sre^ } Y lour f•SPMn ofAap•an Roofury CanaM Mansard or Steep Slope Fastening Pattern i I i i Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7 Certificate oJAuthorization#9503 Ft.10674-1112 Revision 7:04/18/2016 Page 5 of 8 9 • TRINE 1Y I ER® 6.2.1 Minimum Nailing–TruDefinition Oakridge®,Oakridge®: 4 Nail Pattarn G Nail Pait®m Esq 9*`con 4 davos Esguema con b davos r r I�— tr.—�►1 I�-- ,z��- � tr ---;.I IE— i2°—i►1 5518"Exposure Na[Is 5518 Eitpowre, Nays Eiposld¢ndeb&/8pufg. Clavus Exp?slrl6ede;&5/8pulg. 5b/8"Expusule Cfavos 5518".Exposule Evpcslcl6rr;do`55/8 pu7g. Eatposieibn dp'5/B ping. I Standard Fastening Pattern 6-Nail Fastening Pattern Fastening for Slopes Greater Than 21:12 e�u.Nalls�faLrdnp res wieN Nail,TyplW 1• it Ir - I s..•ocwws.w. -• .w n.�...m •�.w°.rc s.»vr.• v 64M. T-� �. z Four 1"9potf olAsphatl RooBnq Camant Mansard or Steep Slope Fastening Pattern 6.2.1 Minimum Nailing–WeatherGuard®HP: I �, � 8i1a�1�ildr Vbw .t}• :• Fie7ltai�rillYlflir �ti:wr"fir ' i I I Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-117 Certificate of Autiimiztlo.119503 FI.10674-1112 Revision 7:04/18/2016 Page 6 of 8 �. TRINITY ERD 6.3 Hip&Ridge Shingles: 6.3.1 Installation of Berkshire® Hip and Ridge Shingles, High Ridge, WeatherGuard® HP Hip and Ridge Shingles and ProEdge Hip&Ridge Shingles shall comply with the manufacturer's current published instructions, using four I (4) nails per shingle. Installation of DuraRidge'"° Hip & Ridge Shingles shall comply with the manufacturer's current published instructions, using two (2) nails per shingle. Refer to Owens Corning published information on wind resistance and installation limitations, including the use of hand-sealing for wind wairarities. 6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.3.3 Mi i imum Nailing—Berkshire®Hip&Ridge and High Ridge: Fig.t 4 F19.2 Pmva VtAnrl D'uedion A. TopVlew Sldalflew Nails A Nabs Nails 4 I I 1y:Z Top LaNrm ied A I I ,4" Pine, '4 A_ 1 I i 1• 7- 1 A i I I I I Er B-. I I 6.3.4 Minimum Nailing—WeatherGuard® HP Hip and Ridge: Fig.A 91 Fig.C Hip&Ridge Sfiingle Fastening PwrollIn NMtl TopYlevl �—DinV p P Nails `\ 4 4 )a I j Nails Nails 2" I I �• y: I 1 I Eap�s—� osuto V, ocposula Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization 119503 FL10674-1112 Revision 7:04/18/2016 Page 7 of 8 I jTRINITY ERD 6.3.5 Min,imum Nailing-ProEdge Hip&Ridge Shingles: Prevailing . Standard -11•� Wind DirectionFastening Seelent Strip Pattern �! 6'Exposuro • 12. � Sealant Fasten 7+k' 7+/� fi"Exposure Coves Exposed FasUmn with Roof Cement I'�12.—►� 6.3.6 Minimum Nailing—DuraRidgeTm Hip&Ridge Shingles: Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer to Owens Corning pub lished installation instructions for their minimum requirements. i Top View 0 J.1fltaaet�od+�rant een DiracdM dd iirw pn dM*H=ta T II' 1" C 2�1i pato W10 ;� Owcas Cfiiring:Sun�lel s. - no� �Ib� ala$ I 7. LABELING: 7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. 7.2 AsIphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC Taible 1507.2.7.1/R905.2.6.1. 8. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 9. MANUFACTURING PLANTS: Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA requirements. i 10. QUALITY ASSURANCE ENTITY: UL LLC—QUA9625;(414)248-6409; karen.buchmann@ul.com END OF EVALUATION REPORT- Exterior Research and Design,U.C. Evaluation Report 037940.02.12-117 Certificate of AutHorization#9503 FL10674-1112 Revision 7:04/18/2016 Page 8 of 8