HomeMy WebLinkAboutUntitled (2) TEAM HORNER
GET THE MOST OUT OF YO,tU ,
POOL HEATING INVESTM I E
g.
• High performance titanium heat exchanger (Patented ThennoLinpin T90, T115 and T135)
• Microprocessor controlled defrost cycle allows operation down to mid to low 40s OF
• Lockable, flip-out control panel protected against sun and weather
• Built-in drain pan for condensate management f E1�F f+,O_ ' )
• Impact resistant, rust and fade proof cabinet
• Quieter than conventional heat pumps J �) et
PFFD,%11TTi+'!G
St. Lucie County, FL
T55 T75 T90 T115 T135
BTUs =80/80/80 _ - 51,000 _W 72;000�h:aY 96 000 1�i2 OOOw,_. m;__132,000
(watertemp/ambient) air/
relative humidity) 80/80/63 47,000 67,000 90,000 106,000 125,000
_
$ x
0%fi3 U65 000
C.O.P. -80/80/80 5.6 5.4 6.0 5.6 5.7
coefficient of Performance ?80/80/63 5 5 $,3 5 8 :5 4 5 6
(watertemp/ambient air/ s=_= s ..:>_ ? --.- -_. _ .r9 -. ._ =t,rs�'_L
relative humidity) 80/50/63 4.0 4.0 4.2 4.0 4.0
Refrigerant R41QA R410A R410A R410A R410A
Heat Exchanger Tube in Tube Tube in Tube ThermoLinkO ThermoLinko Thermoune
Electrical «kW Input 5 9 6 8
GF
3T9�..7�s��.0
Voltage/Hz/Phase 208-230/60/1 208-230/60/1 208-230/60/1 208-230/60/1 08-230/60/1
oMln CircurtAmpaclty _a.___ 191 w.r' G, 268 r„ ._,__. 402y- --
Max.Fuse Size 30 45 60� 1 60 60
Water Flow ;yMln/Max (gpmj, 20/45 20/45 30/70 30/70 30/70
A Heater Bypass Kit is required when flow rates exceed the maximum
Physical Welght(lbs) z 180 200 255 259a 287Q>
.tea_-
Length x Width x Height(in) 34"x 34"x 28" 34"x 34"x 28" 34"x 34"x 39" 14!'x34"x39'1 4"x 34"x 39"
Shipping $Welght(Ibs) w 220 '240 305 309 V 337
Length x Width x Height(in) 38"x 36"x 33" 38"x 36"x 33" 38"x 36"x 43" 3 "x 36"x 43" 38"x 36"x 43"
Rated to accordance with ARI standard,1160 water temp/aniblent alr/relate humtdtty
Spectficattons subNect to change; „
PrOdUCIng QUHHIV NO PUMPS Sincn 1991
s�
rti
1 ITT II �
z
AQUusACAL
1 CE
ETV
MADE IN USA
AquaCal Autopilot, Inc. 2737 -4th Street North S .Pe ersburg,.FL 33713 7271823.5642
V
if
Overhead Cieara nce
oV@II'tSpg4lltffl ,/��
gutter
.. .
OVERHEAD_
Rain nin-off and 5 feet
sprinklersshouldbe [152 ]
directed away from heater
3_
i
HeatWave SupeiQaie&and TropiCa&(Top View)
SACK
6 inches-
[l 5 CM]
SIDES- S!DES
1 foot 1-foot
[30 cm] [30.�crrj
FRONT
3 feet
[91 cm]
3.3 b Water flow Ra#es'
Maintak water flow rates as indicated.Please note,these specifications relate to the heat pump only. Code-
specified whole system turnover rates must be satisfied.
J!'—',.CAUTION-Failure to heed the following may result in equipment damage.
• Water flow exceeding maximum flow rate may damage heat exchanger;such damage will not be covered under
the equipment warranty
Page-6
NAPA 5•_ TMp�1y
AS1fI0 W{eLi S C f.l: .e+ a,Yom- `ZC_ K-.. 2 - �1Rr' 1 sS s y,YL •Y y' .,y1i"` r
_�;�. _ �-�`b:,,..Q�P.., f _ F`�$ SFr �.. 'u-s�t tg r �: �5 � Sw. 'rr ' 3 "^i -:r.�'�••.rs �-:-
`' on and Rai�'water Rnn ff - � ''
i . Irrigation water may damage heat pump components.Have irrigation water directed away from the heat pump.
. .The heat pump will withstand normal rainfall.Do not allow a roof slope to direct rainwater onto the heat pump.
Have a gutter installed on the roof edge to direct this water away from the heat pump. Or install the heat pump in
another location.
,�..�{,
The heat pump can produce a large amount of water in the form of condensation.The amount of water
depends on air temperature and humidity.
- Install the heat pump with enough height to allow for water drainage.
- Plan for water drainage disposal as needed
_ r
. Build the heat pump pad out of concrete or another code-approved material-
. Confirm the pad can support the weight of the heat pump. See"Weights"on page 40.
Elevate the pad enough to allow for drainage.
• Make sure the pad is flat and level.
. Have the pad extend at least 6 inches from the heat pump base in all directions.
. Do not install the heat pump on soil or grass.
. Do not allow the heat pump base to touch the buildings foundation.
. Do not place the heat pump directly on a concrete floor inside a building. This can cause noisy equipment
vibration.Install vibration dampeners between the heat pump base and floor.
. Equipment pad must meet all requirements of authorities having code-related jurisdiction.
(Anchormgtg Pad r -
- Follow all applicable local,state, and national requirements regarding wind load anchoring.
- The shipping brackets used to tie the heat pump to the pallet are approved mounting(hurricane)brackets. They
can be used to anchor the heat pump to the pad
If needed, contact AquaCal-Customer Support to obtain the correct anchoring kit information.Please have the
heat pump model number and serial number when requesting support See'Identifying Model Specifications"on
page 39.
3 3 a:Clearaiaces
- Proper air circulation is required for the heat pump to operate efficiently.Avoid placing objects near or on top of
the heat pump.This includes shrubbery and lawn furniture.These objects will also hinder maintenance access.
• Avoid storing chemical containers near lithe heat pump.The chemicals can cause equipment damage.
Page-5