HomeMy WebLinkAboutProduct Approval & permit application ALS.APPLICABLE INFO MUST BE COMPLETED FOR APPLICATION TO BE ACCEPTED n
Date: 5-5-2017 Permit Number: ' tpa�i
Building Permit Application
Planning and Development Services
Building and Code Regulation Division
2300 Virginia Avenue,Fort Pierce FL 34982
Phone:(772)462-1553 Fax: (772)'462-1578 Commercial Residential x
PERMIT APPLICATION FOR: To Select from dropbox, click arrow at the end of line
PROPOSED IMOROVEMENT LOCATION:
Address: 2602 Seneca Ave
Legal Description: SAN LUCIE PLAZA S/D-UNIT ONE-BLK 1 C(2602,2608 SENECA AV)W 34 FT
OF LOT 9 AND ALL LOT 10-LESSS 20 FT-(MAP 14/33N) (OR 2088-2782)
Property Tax ID#: 1428-702-0011-000-2 Lot No.
Site Plan Name: Noelke Block No.
Project Name:
Setbacks Front Back: Right Side: Left Side:
DETAILED DESCRIPTION.OF WORK:
Tear off shingle roof Install Peel and stick and 5 v metal roof on a 4/12 pitch
5 V Crimp FI 17022-R6 Tri Built Peel and stick FI 16048-R3
CONSTRUCTION INFORMATION.
Additional work to e e orme under t —checkispermit a appy:
E_] Gas Tank ❑Gas Piping _Shutters Q Windows/Doors
F]Electric 0 Plumbing Sprinklers E Generator V Roof
Total Sq.Ft of Construction: 2500 Sq. Ft.of First Floor:
Cost of Construction:$ 8850.00 Utilities:0Sewer ElSeptic Building Height: 15'
OWNERAESSEE: -CONTRACTOR: `
Name Joe and Gina Noelke LLC Name: Richard A. Newland
Address:480 River Prado Company: Richie the Roofer
City: Fort Pierce, State:FL Address: 6704 Santa Clara Blvd
Zip Code: 34946 Fax:216-0259 T City: Fort Pierce State:FL
Phone No.772-321-5951 Zip Code. 34951 Fax: 866-610-8652
E-Mail: Phone No. 772-464-4329
Fill in fee simple Title Holder on next page(if different E-Mail: dchieroofer@yahoo.com
from the Owner listed above) State or County License: CCC058021
If value of construction is$2500 or more,a RECORDED Notice of Commencement is requiied.
SOOPLEMENTAL CONSTRUCTION LIEN LAW INFORMATION: .
DESIGNER/ENGINEER: _Not Applicable MORTGAGE COMPANY: _Not Applicable
Name: Name:
Address: Address:
City: State: City: State:
Zip: Phone: Zip: Phone:
FEE SIMPLE TITLE HOLDER: _Not Applicable BONDING COMPANY: _Not Applicable
Name: Richard A Newland Name:
Address: 905 13th st sw Address:
City: Vero Beach City:
Zip: 32962 Phone: 772-473-6197 Zip: Phone:
I certify that no work or installation has commenced prior to the issuance of a permit.
St.Lucie County makes no representation that is granting a permit will authorize the permit holder to build the subject structure
which is in conflict with any applicable Home Owners Association rules,bylaws or and covenants that may restrict or prohibit such
structure.Please consult with your Home Owners Association and review your deed for any restrictions which may apply.
In consideration of the granting of this requested permit, I do hereby agree that I will,in all respects,perform the work
in accordance with the approved plans,the Florida Building Codes and St.Lucie County Amendments.
The following building permit applications are exempt from undergoing a full concurrency review:room additions,
accessory structures,swimming pools,fences,walls,signs,screen rooms and accessory uses to another non-residential use
WARNING TO OWNER:Your failure to Record a Notice of Commencement may result in your paying twice for
improvements to your property.A Notice of Commencement must be recorded and posted on the jobsite
before the first inspection. If you intend to obtain financing, consult with lender or an attorney before
commencing work or recording our Notice of Commencement.
-f` s
_Signature of Owner/Lessee/Agent � ure of Contractor/License Holder;
STATE OF FLORIDA STATE OF FLORIDA
COUNTY OF �� ,�,�� COUNTY OF zk- o
The forgoing inst ument was acknowledged before me The forgoing instrument was acknowledged before me
this 3\ day of 20LLby this,31 day of Q,6,T 20 1 by
1
(Na of person acknowledging) (Name of person acknowledging)
&_u' Lt:�4
WgnatLke of Notary Public-State of F rida) (Signature of NotaryPublic-Sta of Florida)
Personally Known OR Produced Identification Personally Kno OR Produced Identification
Type of Identification Produced Type of Identificatio tr
�", 'AL HAr Nq'INGRAM LASHAHN RAM
Commission No. ••'CRY"�' tary Publeaate of Florida Commission No. ' T Notary Pu(�eaytaNe ofNu
Florida
2' a. a `µ• MY Comm.Expires Dec 20,
' My Comm.Expires Dec 20,2018 Com 2018
""' gontled through Na�!ona, ',,.
Revised 07/15 �� '�"'� Bow through National Notary Assn. �;,E y � �
-REVIEWS FRONT ZONING SUPERVISOR PLANS VEGETATION SEA TURTLE MANGROVE
COUNTER REVIEW REVIEW REVIEW REVIEW REVIEW REVIEW
DATE
COMPLETE
INITIALS
2014 Florida Building Code (5th Edition)
BUILDING INFORMATION Mills, JOB INFORMATION
//tl
Design Wind Speed Nominal ' Y ,I J I s, Sh ort ? A ssoci ates Client Richie the Roofer,Inc/Joe&Gina Noelke LLC
Ultimate Wind Velocity(mph) 160
Nominal Wind Velocity(mph) 123.9
Exposure C Eight Hundred Eighth Street PHONE:772.2%.7202 Address 2602 Seneca Ave.,Fort Pierce,FL
Internal Pressure Enclosed Vero Beach,Florlda 32862 w y_MU pt" �� Company Mills,Short&Associates,LLC
—Height above ground z)-(ft) 0.0 Job Number 17-1950
Standard Wall Height-ft) 8.0 ASCE 7-10 Pre arcr Jason W.Short,P.E.
Mean Roof Height h)- ft) 15.0
Building Width(ft) 60.0
BuildingLength(ft) 25.0 Version 7.1 TOPOGRAPHIC FACTOR
Roof Sloe x:12) 5.0 2004-20120 Hill Shape Flat-No Hill
Roof Angle(degrees) 22.62 H, ft 0.0
a)Edge Strip(ft) 3.00 Building Permit Edition Lh, ft 0.0
End Zone(ft) 6.00 x, f) 0.0
Parapet Along Roof Perimeter(ft) o.00 Wind Load Program z, ((t) 0.0
WIND LOAD DESIGN INFORMATION
Nominal Wind Load Pressures
OPWIDTH LENGTH ENING EFFECTIVE
d MAXIMUM MAXIMUM
z APPLYING WIND LOAD FOR: ZONE ELEVATION ( ) ( )feet feet WIND AREA NOA Approval Number Max Pressure Per NOA Manufacturer Model Number
(feet) (sqft) POSITIVE NEGATIVE
PRESSURE(psf) PRESSURE(psf)
Gable 1-Gable N/A 3.0 3.0 9 19.3 -30.6 FL 17022-R6 -86 PSF-Method 1 Extreme Metal Fab. 5V-26 Ga.
o Gable 2-Gable N/A 3.0 3.0 9 19.3 -53.3 FL 17022-R6 -86 PSF-Method 1 Extreme Metal Fab. 5V-26 Ga.
Gable w/Overhan 3-Gable N/A 3.0 3.0 9 19.3 -105.0 FL 17022-R6 -228 PSF-Method 4)1 Extreme Metal Fab. 5V-26 Ga.
II **Underlayment is FL 16048-R3"Tri-Built'**
O
w
Z
0
0
a
z
0
F
J
O
z
z
w
0
0
a
a
d
3
i
i
1>
� • t OF . ��
,. � 1�10P'.•'•.Cj��
f
i
Fit
A 1' r 0• D Q ff t 1 ® i-7U Y[(x/.
BCIS Home Log In I User Registration i Hot Topic Submit Surcharge Stats&Facts Publications I FBC Staff BCIs Site Map Unks search
��rida
,.` tri° Product.Approval
USER:Public User
Product Anoroslal Manu->.Product or AoalicA n 5earch>Annlication'U.51>Application Detail
•' -�. ��i FL# FL16048-R3
Application Type Revision
Code Version 2014
Application Status Approved
Comments
Archived T
Product Manufacturer TRI-BUILT Roofing Products
Address/Phone/Email 9050 Louisiana Street.
Merrillville,IN 46410
(201)842-2449
david.ruiz@tribuiltmaterjalsgroup.com
Authorized Signature David Ruiz
da.vid.ruiz@trib,uiltii.naterialsgroup.com
Technical Representative David Ruiz
Address/Phone/Email 250 Route 17 North
East Rutherford,NJ 07073
(201)842-2449
david.ruiz@tribuiltmatdridlsgroup.com
Quality Assurance Representative
Address/Phone/Email
Category Roofing
Subcategory Underiayments
Compliance Method Evaluation Report.from a Florida:Registered Architect or a'Licensed
Florida Professional Engineer
Evaluation.Report-Hardcopy Received
Florida Engineer orArchitect Name who developed Robert Nieminen
the Evaluation Report
Florida License PE-59166
Quality Assurance Entity. UL LLC
Quality Assurance Contract.Expiration Date 10/16/2017
Validated By John W.Knezevich,-PE
Ell Validation Checklist-Hardcopy Received
Certificate of Independence FL16048 R3 COI.2015 01 COI Nieminen.pdf
Referenced Standard and Year(of Standard) Standard Year
ASTM D1970 2009
ASTM G15S 2005
FRSA/TRI April 2012(04-12) 2012
TAS 103 1995
Equivalence of Product Standards
Certified By
Sections from the Code
V
i
Product Approval Method Method 1 Option D
Date Submitted. 10/08/2015
Date Validated 10/19/2015
Date.Pending FBC Approval 10/21/2015
Date Approved 12/15/2015
Date Revised 10/06/2016
Summary of:Products
FL# Model,Number or Name Description
16048.1 TRI-BUILT Roof Underlayments Self-adhering,modified bitumen roof underlayments
Limits of.Use- Installation Instructions
Approved.for use in HVHZ:No FL16048 R3 1I 2015' 10 FINAL ER TRI-
Approved for use.outside HVHZ:Yes B(JTLT UNDERLAYMENTS'FL16048-R3 ndf
impact Resistant,N/A Verified By:Robert Nieminen PE-59166
Design,pressure"..w1-.N/A/-45' Created by Independent Third Party:Yes
Other:-1.1 The design pressure;noted herein pertains-to use Evaluation Reports
of foam-on the systems overtop the self=adhering Fl wms R3 AE 2015 10 FINAL ER TRT-
undertayment`for one particular apptication.See ER Section �3l�ILT UNDFRLAYMENTS FL16048-R3.odE
5.6 for details.2.)Refer to ER Section 5 for other Limits of Created by Independent Third Party:Yes
use.
Back NeM
Contact Us 2:2601'Biair Stone Road,Tallahassee FL 32399 Pnone:850-487-1824
The State.of:Florida is an AA/EEO employer.Comeright2007=2013 State of.Florida..is Privacy StatemenP:f Accessibility Statements:Refund Statement
Under Florida law,email addresses are public records.If-youdo not want your e-mail address released in response to a publicrecords request,do not send electronic
mail.to'this entity.;Instead,-contact the offrce.by phone or by traditional mail.If you have'a'nyquestions,.please contact 850.487.1395:-Pursuant to.Section 455.275
(1),Florida Statutes,effective October 1,2012,'licensees licensed under Chapter 455,F.S.must provide the Department with an'emal address if they have one.The
emails provided may be used for omrial communication with the licensee-However email addresses are public record.If you do not wish to supply-a personal address,
please provide the Department with an email.address whkh can be made available to the public.To determine if you,are a licensee under Chapter 455,FS.,please
rick hCre.
Product Approval Accepts:
Credt Card'
Safo
EXTERIOR RESEARCH&DESIGN,I.I.C.
Certificate of Authorization#9503
..""Q
TRIM TY180 353 CHRISTIAN STREET,UNIT#13
OXFORD,CT 06478
PHONE:(203)262-9245
EVALUATION REPORT FAX:(203)262-9243
Allied Building.Products Corp. Evaluation.Report A42960.10.12-R3
dba TRI-BUILT Roofing Products
FL16048-R3
9050 Louisiana Street Date-of Issuance:10/2S/1012
Merrillville,IN 46410 Revision 3: 10/08/2015
SCOPE:
This Evaluation Report is issued under Rule 61(320-3.and the applicable rules and regulations governing the use of
construction materials* in the State of Florida:The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the-product under the-Florida Building Code and Florida Building Coder Residential Volume. The
products described herein have been evaluated for compliance with the 5c' Edition (2014) Florida Building Code
sections noted herein.
DEscpjpTioN: TRI-BUILT'RogWriderlayments
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE:This Evaluation Report is valid untilsuch time as the.named pro'duct(s)changes,the referenced
Quality Assurance,documentation changes,or provisions of the-Code that relate.to theproduct change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert, Nieminen, P.E. if the product
changes Or the referenced Quality Assurance documentation changes. Trinity'I ERD requires a complete:review of this
Evaluation Report relative to updated Code requirements with each Code Cycle..
ADVERTISEMENT:The Evaluation Report number preceded by--the words"Trinity)ERD Evaluated" may be-displayed in
advertising literature. If any.portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION:Upon request, a'copy of this entire`E'valuation Report shall be,provide'd to the.userby the manufacturer or
its distributors and shall be available for inspection at the job site at the.request of the Building
uilding Official.
This Evaluation Report consists of pages I through 5.
Prepared by,
A
Robert J.M.Nieminen P.E.
The facsimile seal appealing was auftrized by Roben Nieminen,
Px.�ca"AA*/IGAS.This does not serve as
an electronically signed
Florida Registration No.59166,-Florida DCA ANE1983 document Signed;sea I W hardicoplas�ave been tmqsrftttted to the
CERTIFICATION OF INDEPENDENCE: Product Approval A4ndnizimtor and to the named cuent
1. Trinity I ERD,does not have, nor does it intend to acquire of will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity I ERD'isnot owned,operated or controlled by any company manufacturing or distributing products it evaluates.
'3. Robert Nlerninen,P.E.does,not have nor Will acquire,a financial interest in any company manufacturingordistributingproducts for
which the evaluation reports,;i.re being Issued.
4. Robert Nieminen,P.E.does not have,nor Will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This Is-a building code evaluation. Neither Trinity I ERD nor Robert Nieminen,P.E.are,in anyway,the Designei of Record for any
project.on which this Evaluation Report,or previous versions thereof,is/was-used,for permitting or design guidance unless retained
specifically for that purpose.
i
TTRINITYIERD
ROOFING.COMPONENT EVALUATION:
1. SCOPE:
Product.CategOry:' Roofing:
Sub=Category: Underlayment
ComplianceStatement: TRI-BUILT Roof Underlaymbhts„as produced`by:TRI'-HbiLT,have demonstrated compliance
with the1ollowingsections.of the Florida Building Code through testing in accordance with the following Standards.
Compliance is subject to.the Installation Requirements and Limitations/Conditions of.Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1507.2.4;1507.2.8,1507..9.2;. Physical Properties ASTMD1970 201,09,
1507.4.5.1,1507.5.3,1507:7.3
1504.6 Ayceierated weathering ASTM G155 2005
1507.3.3; Installation Practice FRSA/TRI April•2012(0412) 2012
1523:6:53:1 Physical Properties TAS 103 1995
3. REFERENCES:
Entity Examination Reference Date
ERD(TST6049) Ph
RD 540540.02.13-1 02[19/2013
ERD(TST6049) Physical Properties 540540.11.13 11/19/2013
ERD(TST6049) RhyAca).Properties 540540.03 14 03/26/2014
ERD(TST6049) Physical Properties 544870.04.14-2. 04/02/2014
ERD(TST6049) Physical Properties 544870.04.14-3 04/02/2014
ERD(TST6049) Physical'Properties 544870.04.14-1 04/10/2014
ERD(TST6049) Physical Properties 544870.04.14-4 04j10/2014
ERD(TST6049) Physical Properties 543530.02.14-1-R1 05[14/2014
ERD'(TST6049) Physical Properties 543530:05:14 05/28/2014
ERD(T5T6049) Physical Properties S4054p.10.14 10/31/2014
ERD(TST6049) Physical Properties' SC7645,.02.15 02/-3/2015,
ERD.(TST6049) Accelerated weathering SC8520.04A5 05/27/2015
UL,LLC.(QUA9625) Quality Control Multiple-listing R16814 09/04/2015.
UL,LLC.(QUA9625) Quality Control Service Confirmation Exp:•10/16/2017
4. PRODUCT DESCRIPTION:
4:1 Self-Adhering,Underlayments:
4.1.1 Tri-Built Sand-R SA Shingle :Underlayment ;is a self-adhering; glass-mat reinforced, sand-surfaced, SBS
modifiedbiturnen roof underlayment,with a 364hch sheet width..
4.1.2 Tri-Built S/A HT TU Underlayment is.a self-adhering,non-woven polyester fabric surfaced, SBS modified
bitumen roof underlayment
4.1.3 Tri-Built Smooth HTS/A Underlayment;isa.elf=adhering,.;glass-mat.reinforced;film-surfaced,SBS modified
bitumen roof underlayment.
5. LIMITATIaNS:
5.1, This-is a building code evaluation. Neither Trinity iERD:nor-Robert Nigminen, P.E. are, in any way,the
Designer of Record,fou any project on which this.Evaluation Report, or previous versions thereof,is/was
used_for permitting or design guidance unless.retalned.specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not 'part of this Evaluation Report;. refer to current Approved Roofing Mated6is
Directory for fire ratings of this product.
Exterior Research acid Design,i[C. Evaluation Report A42960:10.12-R3
eerrijtcare of Aiirhnrfiotion-/9503 FL16048-R3
Revision 3-.10/08/2015
Page 2 of-S
r
` TRINITY i ERD
5.4 TRI-BUILT Roof Underlayments.may be used with any prepared roof cover where the product is specifically
referenced within FBC approval documents. If not listed,.a,request may be made to the AHJ for approval
based on this evaluation combined with supporting data for the prepared roof covering.
5.5 Allowable roof covers applied atop the.underlayments are as follows:
TABLE 1 ROOF COVER OPTIONS
Undedayment Asphalt Nail-Ontile Foam-On Tile Metal Woad.Shakes. Slate
Shingles- &Shingles
Tri-Built Sand-R SA Shingle Yes No No No Yes Yes
Underlayment
Tri-Built.S/A HTTU Yes
Yes Yes Yes Yes Yes
Underlayment See 5.5.1
Tri-Built Smooth HT S/A Yes No No Yes Yes Yes
Underlayment
5.5.1 "Foam-0n Tile" is limited to use of the following Approved:tile adhesives unless tensile adhesion/ long.
term aging data from an.accredited testing laboratory is provided.
➢ Tri-Built S/A HT TU Underlayment with:31VI"'2-Component Roof Tile Adhesive AH-160(FL6332)or Dow
TileBon&'°Roof Tile Adhesive(FL717)
5.6 Allowable substrates are noted below:
5.6.1 Direct-Bond to Deck:
Tri-Built Sand-R SA Shingle.Underlayment,Tri-Built S/A HT TU Underlayment or Tri-Built-Smooth HT S/A
Underlayment applied to:
➢ Plywood, ASTM D41 primed plywood; OSB; ASTM -D41 primed OSB; ASTM D41 primed structural
concrete.
While not required over plywood,OSB or Southern Yellow.Pine substrates,-TRI-BUILT recommends priming
the deck if the final roof cover is not slated for installation.within 24 hours;. Note: TRI-BUILT requires
tongue-and-groove board decking be covered with plywood or USB prior to installation_ of the self-
adhering.underlayment.
5.6.2 Bond-to-Insulation:
Tri-Built S/A HTTU Underlayment applied to:
Dens Deck Prime;SECUROCK Gypsum-Fiber Roof Board'.
For installation, under mechanically attached prepared roof coverings, insulation shall be attached per
minimum requirements of'the prepared roof covering manufacturer's Product Approval. For installations
under foam-on file systems,insulation attachment shall be designed by a qualified design professional and
installed based on testing of the insulation/undedayment;system in accordance.with FM 4474,Appendix D
orTAS°114,Appendix J.
5.6.3 Bond to Mechanically Attached Base Layer:
➢ ASTM D226,Type I or II felt.
For installations under mechanically attached prepared roof coverings, baselayer shall be attached Per
minimum.codified requirements. For installations under foam-on tile systems;base layer shall be attached
per minimum requirements of FRSA/TRI.April 2012(0442):
Exterior Research and Design,LLC. Evaluation Report A42960.10.12-R3
CertrTicate ofAuthatfiatian#9503 FL16048-R3
Revislon 3:10/08/2015
Page 3 of 5
�f RlNI'r ERD
L
5.6.4 Wind Resistance for Underlayment Systems in Foam-On Tile Applications: FRSA/TRI April 2012 (04-12)
does not address wind uplift resistance of all underlayment'systems.beneath foam-on the systems,where
the underlayment.forms part of the load-path. The following wind uplift limitations apply to direct-deck
underlayment systems that are not addressed in FRSA/TRI April_2012(04-12)and are used in foam-on the
applications. Maximum Design Pressure is the result of testing for wind load resistance based on
allowable wind loads,and reflects the ultimate passing pressure divided by 2(the 2 to 1 margin of safety
per FBC 1504.9 has,already.been applied). Refer to FBC 1609 for determination of design wind pressures.
5.6.4.1 Maximum Design Pressure=-45.0 psf.
Deck: Min.15%32-inch plywood to meet project requirements to.satisfaction ofAHJ.
Primer: (Optional)ASTM D41
Underlayment: Tri-Built SIA HT TU Underlayment,self-adhered.
5.7 Exposure Limitations:
5.7.1 Tri=Built Sand-R SA Shingle Underlaymerit or Tri-Built Smooth_ HT S/A"Underlayment shall not be left
exposed for longer than-30-days after installation
5.7.2 Tri-Built S/A HTTU Underlayment shall not be left exposed The longer than 180-days after installation.
6. INSTALLATiow
6.1 TRI-BUILT Roof Underlayments shall be installed in accordance with TRI-BUILT published installation
,requirements subject to the Limitations set forth in Section 5 herein and the-specifics noted below.
6.2 Re-fasten any loose decking panels,and check for protruding nail heads. Sweep the substrate thoroughly
to rernove any dust and debris;prior to application,and prime the substrate((f applicable).
6.3 Tri-Built Sand-R SA Shingle Underlayment,Tri-Built S/A HT TU UnderlaVrhent or Tri-Built Smooth HT S/A
Underlayment:
6.3.1 Shall be.installed in compliance with.the requirements for ASTM D1970 underlayment in FBC Sections
1507 for the type of prepare4 roof covering to be installed.
6.3.2 Non-Tile applications:
While priming is optional,TRI-BUILT recommends priming-the deck if the final roof cover is not slated for
installation within 24 hours.
Apply sheet parallel to the roof edge. Rollout approximately 10 ft of membrane and peel back the first 3
ft of release film.
Adhere theexposed part to the substrate and unroll the remaining membrane as far as possible.
Once the:entire length of membrane is in place, peel-off the.release film diagonally while holding.the
membrane tight. Firmly roll.the membrane into place to achieve-a bond.
Horizontal seams should be minimum 3-inches, configured to shed.water. Vertical seams should be 6-
inches and staggered not less than 2.-ft from vertical seams-in the-course below. All over-granule end-laps
shall be sealed using either heat-welding or.hot air welding techniques.
When installing at slopes above 8:12, Allied Building Products Corp recommends back-nailing in the
overlap area at the top of the sheet at 12-inch o.c.
For Valleys and Ridges: Cut underlayment into 4,m6.foot,lengths.Peel the release paper and center sheet
over valley or ridge. Drape and press.sheet into place, working from the.center of the valley or ridge in
each direction. For valleys,apply-the sheet starting at the lowest point and work upward.
6.3.3 tile.Applications(tri-Built SIA HT TU Underlayment only):
Reference is made to FRSA/TRI April 2012 (04-12) Installation Manual and Table 1 herein, using the
instructions noted above as a-guideline.
Tile shall be loaded and staged in a manner that prevents tile slippage and/or damage to the
underlayment.
Exterior Research and Design,LLC_ Evaluation.Report A4296010.12-R3
Certtflwte of Authoiiratfan#9503 FL16048-113
Revision 3:10/08/2015
Page r4 of 5
TRINITY'ER®
7. BUILDING:PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the-installation of
this product.
8. MANUFPicrURINGPLANTS:
Contact the noted QA agency for information on product locations covered-for F.A.C.=Rule 9N-3 QA requirements.
9. QUALITY ASSURANCE Emu:
UL,LLC—QUA9625;(314)S78-3406;-.k.chancellor@us.ul.com
-END OF EVALUATION REPORT-
Exterior Research and Design,LLC. Evaluation.Report A42960.10.12-R3
Cenffflarte of Authorf:atfon 49503 F1.16048-113
Revision 3:10/68/2015
Page 5 of 5
L•
w I o � A A a 4 a 9 + •Y,.
91,
8CIS Home } Log In User Registration i. Hot Topics ( Submit Surcharge ; Stats&Facts Publications } F8C'Staff} acts Site Map Emla I Search J
O
-r E0Product Approval
USER:Public User r
Product Annroval Menu>Product or Aonlication Srarc-h>AnMKaiitml7st>Application Oxtail
• *. FL# FL16048-R3
Application Type Revision
Code Version 2014
Application Status Approved
Comments
Archived
Product Manufacturer TRI-BUILT Roofing Products
Address/Phone/Email 9050 Louisiana Street
Merrillville,IN 46.410
(201)842-2449
david.ruiz@tribuiltmaterialsgroup.com
Authorized Signature David Ruiz
david.ruiz@.tribuiltmaterlaisgroup.com
Technical Representative David Ruiz
Address/Phone/Email 250-Route 17-North
East Rutherford,NJ 07073
(201)842-2449
david.ruiz@tribuiltmaterialsgroup.com
Quality Assurance Representative
Address/Phone/Email
Category Roofing
Subcategory Underlayments
Compliance Method Evaluation Report from a Florida Registered Architect ora`Licensed
Florida.Professional Engineer
L3 Evaluation Report-Hardcopy Received
Florida Engineer or-Architect Name:who developed Robert Nieminen
the Evaluation Report
Florida License PE-59166
Quality Assurance Entity UL LLC
Quality Assurance Contract Expiration Date 10/16/2017
Validated By John W.Knezevich,_PE
Validation Checklist-Hardcopy;Received
Certificate of Independence FL16048 R3 C01 2015 01 C01 Nieminen.odF
Referenced Standard and Year(of.Standard) Standard Year
ASTM D1970 2009
ASTM G155 2005
FRSA/TRI April 2012(04-12) 2012
TAS 103 1995
Equivalence of Product Standards
Certified By
Sections from the Code
SS '
1 f
Product Approval Method Method 1 Option D
Date Submitted 16/08/2015
Date Validated 10/19/2015
Date.Pending FBC Approval 10/21/2015
Date Approved 12/15/2015
Date Revised 10/06/2016
Summary of Products
FL# Model,Number or Name Description
16048.1 TRI-BUILT Roof Underlayments Self-adhering,modified bitumen roof underlayments
Limits of Use Installation Instructions
Approved for use in HVHZ:No FL16048 R3 II 2615 10'FINAL ER TRT-
Approved for use:outside 14V"2:Yes BUILT UNDERLAYMENT5'FL16048-R3.odf
Impact Resistant:N/A Verified By: Robert Nieminen PE7-59166
Design Pressure.-+N/A/-45 Createdby Independent Third Party:Yes
Other:.1.)The design pressure noted herein pertains-to use Evaluation Reports
of foam-ori tile:systems overtop-the self-adhering FI 16043 R3 AE 20t5 10 FINAL ER TRi-
underlayment for one particular application.See ER Section DUILT UNDERLAYMENTS.17136048-113.Ddf
5.6 for details.,2.).R4er to ER Sections for other Limits of Created by Independent Third Party:Yes
Use.
&Ick Next
Contact Us.:2601 aiair Stone Road.Tallahassee FL`32399 Phone:850-487-1824
The StateofFlorida is an WEED erriployec Comirinht 2007=2013'State of.Florida.::Privacy Statement::Accessibility statemen[::Refund'5tatement
Under Florida law,email addresses are public retards.If you do not want your e-mail address released in response to'a public-moords request,do not send electronic
mail.to this entity:instead,contact the office by phone or by traditional mail.If you have any'questions,please contact 850.487.1395.*Pursuant to Section 455.275
(1),Florida Statutes,effective October 1,2012,licensees 0censed.under chapter 455,F.S.must provide the Department with an email addreis if they have one.The
emaiLs provided maybe used for official communication with the licensee.However email addresses are public record.If you do not wish to supply a personal address,
please provide the Department with an email_address which.can be made available to the public.To determine if you are a licensee under chapter 455,F.S.,please
. . dick ere.
,Product Approval.Accepts:
aUMf M
Credit Card
t e 1.
n ,
^
,
GXTERIOR0����&DESIGN,I.I.C.
~+� Certiftate of AWhorization#9503
\. / U���� 35�CHRy�7AN3TREB�UNIT#l3
~~J � ������ � � �'x-o��� _
^ \ OXFOR[\CT0G478
PHONE:(2O3)lBJ'9245
EVALUATION REPORT FAX:(2U3)262'9243
Allied-Building.Products Corp. Evaluation.Report A42960.10.12-R3
dba TRI-BUILT Roofing Products FL1604843
9050 Louisiana Street Date of Issuancm 10/25/2012
Merrillville,IN 46410 Revision 3: 10/08/201S
This Evaluation Report is issued under Rule'G1G20-3and the 6pp|ioaNemlesand regulations governing the use of
construction materialsi the State of Florida.The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use product under the Florida Building Code and Florida Building Code, Residentia| Volume. The
products described herein have been evaluated for compliance with the �m Edition (2014) Florida Building Code
sections noted herein.
mESCnpnom: TRI-BUILT@p9fUuderlaymmemts
Lxasuma: Labeling shall bein accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: Evaluation Report isvalid until such time asthe named produot(s)chang�'the referenced
Quality Assurance clocurneritation changes,-or provisions of the Code that relate,to the,product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. ifthe product
h
c on8esorzne'refenenceUQua}ityAsurancedocumentatjpnchanges. Trinbyl E8Drequires acomplete'cevemo[this
Evaluation Report relative to updated Code requirements,mith each CodeCycle.
AaneemScMEmriTheEvaluation Report number preceded by the words"Trinity I ERD Evaluated" may be displayed in
advertising literature. If any portion ufthe Evaluation Report isdisplayed,then-it shall be,6one ioits entirety.
INsPEcnoN:Upon request,a copy of this entire'Evaluation Report shall be provided to the user bythe manufacturer or
ksd|utd6utocsand shall 6e available for inspection atthe job s� request
This Evaluation Report consists ofpages 1through 5.
Prepared by:
r
Robert J.M.Niennoen P.E.
The facsimile seal appeamillyvas authorized by Robert Nlemliren,
Florida Registration No.59166,Florida DC4 Am£2983 "^=
20M/2915.This does narserveasanele(lmniCally*ned
document St ealed hardcopies have been tranwnitted to the
ProductCERTIFICATION OF '�� ' '—'--abor '--'------
1. ThnhNE8Ddoes not have, nor does itintend ruacquire o,will it acqmnejufinancial interest inany company manufacturing nr
di,tr/butUig.products it evaluates.
Z. ThnhyiERDbnouowne4operated uromnun|ledbyany company manmauu,riilgp,d$tr|buunmproducts itoaluates
s. Robert mieminon,p.E.does not,have nor will mcqu/n0%,ofinancial interest many company manufactuhmgo,distnbmi —products.for
which the evaluation repomtsuebeing issued.
4. Robert mie.minen,p.E.does not have,nor will acquire,afinancial interest inany othe,eofityinvolved inthe approval process of the
product
S. This isabuilding co" e�q|vauio". we*he"Txv�,|Enonor nnbe�miemine�P'�mn�many waKthe oekmqe,ufRecord for any
pn�e��.oh\wmuhth|�Evaluation Report,o,previous versions thereof,is/was used for permitting ordesign guidance unless retained
specifically for that purpose.
TRINITY+ER®
d
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Underlayment
Compliance Statement: TRI-BUILT Roof Underlayments,as produced by TRI-BUILT,have demonstrated compliance
with the following.sections of the Florida Building.Code through testing in accordance with the following Standards.
Compliance is subject to the Installation Requirements and:Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1507.2.4,15.0.7.2.8,1.507:2..9.2, Physical Properties ASTM.D1970 2009
1507.4.5.1,1507.5:3,1507.7.3
1504.6 Accelerated Weathering ASTM,G155 2005
1507.3.3 Installation Practice FRSA/TRI April 2012.(04-12) 2012
1523.6.5.2.1 Physical Properties TAS 103 1995
3. REFERENCES:
inti y Examination Reference Date.
ERD(TST6049) Physical Properties 540546.02.13-1 02/19/2013
ERD(TST6049) Physical Properties S40540.11.13 11119/2013
ERD(TST6049) Physical Properties 540540.03.14 03/26/2014
ERD(TST6049) Physical Properties 544870.04:14-2 04/02/2014
ERD(TST6049) Physical.Properties 544870:04.14-3 04/02/2014
ERD(TST6049) Physical'Properties 544870.04.14-1 04/10/2014
ERD(TST6049) Physical Properties 544870.04.14-4 04/10/2014
ERD(TST6049) Physical Properties 543530.02.14-1-R1 05/14/2014
ERD(TST6049) Physical Properties 543530.05.14 05/28/2014
ERD(TST6049) Physical Properties 540540:10.14 10/31/2014
ERD(TST6049) Physical-Properties SC7645.02.15 .02/13/2015
ERD.(TST6049) Accelerated Weathering SC8520.04.15 05/27/2015
UL,LLC.(QUA9625) Quality Control Multiple-Listing R16814 09/04/2015
UL,LLC.(QUA9625) Quality Control Service Confirmation Exp:10/16/2017
4. PRODUCT DESCRIPTION:
4.1 Self-Adhering Underlayments:
4.1.1 Tri-Built Sand=R SA Shingle Underlayment is a self-adhering; glass-mat reinforced, sand-surfaced, SBS
modified bitumen roof underlayment,with;a364nch sheetwidth.
4.1.2 Tri-Built S/A HT TU Underlayment is a self-adhering, non-woven polyester fabric surfaced, SBS modified
bitumen roof"underlayment
4.1.3 Tri-Built Smooth HT 5/A Underlayment is a self-adhering,glass-mat reinforced,film-surfaced,SBS modified
bitumen roof underlayment.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither Trinity)ERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was
used for permitting or design guidance unless retained.specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification. is not part of this Evaluation Report; refer to current Approved Roofing Materials
Directory.forfire ratings of this product.
Exterior Research and Design,LLC. Evaluation Report A42960.10.12-R3
Certijreate ofQuthoriiothn#003 F1.16048"113
Revision 3:10/08/2015
Page 2 of 5
TRINITY I ERD
t
5.4 TRI-BUILT Roof Underlayments may be used with any prepared roof cover where the product is specifically
referenced within FBC approval documents. If not listed,arequest may be made to the AHJ for approval
based on this evaluation combined with supporting data for the prepared roof covering.
5.5 Allowable roof covers applied atop the underlayments are as follows:
TABLE 1 RooF Coven OPnO.NS
Underlayment Asphalt Nail-On Tile Foam-On Tile Metal 1A&Shingles ood shakes
Shingles &SSlate
Tri-Built Sand-R SA.Shingle Yes No No No Yes Yes
Underlayment
Tri-Built S/A HT TU Yes
Yes Yes Yes Yes Yes
Underlayment See 5:5.1
Tri=Built Smooth HT.S/A yes No No Yes Yes Yes
Underlayment
5.5.1 "Foam-On Tile" is limited to:use of the following Approved tile adhesives unless tensile adhesion/long
term aging,data from an accredited testing laboratory is.provided.
➢ Tri-Built S/A HT TU Underlayment with 3M1 2-C6.mponent Roof Tile Adhesive AH-160(FL6332)or Dow
TileBondTM'Roof Tile Adhesive(FL717)
5.6 Allowable substrates are noted below:
5.6.1 Direct-Bond to Deck:
Tri-Built Sand-R.SA Shingle.Underlayment,Tri-Built S/A HT TU Underlayment or Tri-Built Smooth HT S/A
Underlayment applied to:
➢ Plywood; ASTM D41 primed plywood; OSB; ASTM D41 primed OSB; ASTM D41 primed structural
concrete.
While not required over plywood,OSB or Southern Yellow Pine substrates,TRI-BUILT recommends priming
the deck if the final roof cover is not slated forinstallation within 24 hours. Note: TRI-BUILT requires
tongue-and-groove board decking be covered with plywood or OSB prior to installation of the self-
adhering underlaymeni.
5.6.2 Bond-to-Insulation:
Tri-Built S/A HTTU Underlayment applied to:
➢ Dens Deck Prime;SECUROCK Gypsum-Fiber Roof Board.
For installation under mechanically attached prepared roof coverings, insulation shall be attached per
minimum requirements of the prepared roof.covering manufacturer's Product Approval. For-installations
under foam-on the systems,insulation attachment shall be designed by a qualified"design professional and
installed based on testing of the insulation/underlayment system in accordance with FM 4474,Appendix D
or TAS.114;Appendix J.
5.6.3 Bond to Mechanically Attached Base Layer:
➢ ASTM D226,Type I or Il felt.
For installations under mechanically attached prepared roof coverings, base layer shall be attached Per
minimum codified requirements. For installations under foam-on tile.systems,base layer shall be-attached
per minimum requirements�of FRSA/TRI April 2012(04-12).
Exterior Research and Design,U.C. Evaluation Report A42960.10.12-113
Certificate of Authorization#9503 F1.15043-113
Revision 110/08/2015
Page 3 of 5
r
i
'•. TRINITY.(ERD
1
5.6.4 Wind Resistance for Underlayment Systems in Foam-On Tile Applications: FRSA/TRI April 2012 (0412)
does not address wind uplift resistance of all underlayment systems beneath foam-on tile systems,where
the underlayment forms part of the load-path. The following wind-uplift limitations apply to direct-deck
underlayment systems that.are not addressed in FRSA/TRI April 2012(04-12)and are used in foam-on the
applications. Maximum Design Pressure is the result of testing for wind_ load resistance based ort
allowable wind loads,and reflects the.ultimate passing pressure divided by 2(the 2 to.1 margin of safety
per FBC 1504.9 has already been applied). Refer to FBC 1609 for determination of design wind pressures.
5.6.4.1 Maximum Design Pressure=-45.0 psf.
Deck: Min.15/32-inch plywood to meet project requirements to satisfaction of-AHJ..
Primer: (Optional)ASTM D41
Underlayment: Tri-Built S/A HTTU Underlayment,self-adhered.
5.7 Exbosure Limitations:
5.7.1 Tri-Built Sand-11 SA Shingle Underlayment or Tri-Built Smooth HT S/A Underlayment shall not be left
exposed for longerthan 30-days after installation
5.7.2 Tri-Built S/A HTTU Underlayment shall not be left exposed for longer than 180-days after installation.
6. INSTALLATION:
6.1 TRI-BUILT Roof Underlayments shall be installed in accordance with TRI-BUILT published installation
requirements subject-to the Limitations set forth in Section b herein and the specifics noted below.
6.2 Re-fasten any loose decking.'panels,and check for protruding nail,heads. Sweep the substrate thoroughly
to remove any dust and debris prior to application,and prinie the-substrate(if applicable).
6.3 Tri-Built Sand-R SA Shingle Underlavinent,Tri-Built S/A HTTU Underlayment or Tri-Built Smooth HT S/A
Underlayment:
6.3.1 Shall be installed in compliance with the requirements for ASTM D1470 underlayment in 'FBC Sections
1507 for the type of prepared rroof covering to be installed.
6.3.2 Non-Tile applications:
While priming`is optional,TRI-BUILT recommends priming the deck if the final roof cover is not slated for
installation- ithin 24 hours.
Apply sheet parallel to the roof edge. Roll out-appro dmately 10 ft of membrane and peel back the first 3
ft of release film.
Adhere the;exposed part to.the substrate and unroll the remaining membrane as far as possible.
Once-the entire length of membrane is in place, peel-off the release film diagonally while holding the
membrane tight. Firmly roll the membrane into place to achieve a bond.
Horizontal seams should be minimum 3-inches, configured to shed.water. Vertical seams should be 6-
inches and staggerednot less than 2-ft from vertical seams in the course below. All over-granule end4aps
shall be sealed using either heat-welding or hot air welding techniques.
When installing at slopes above 8.12, Allied Building Products Corp recommends back-nailing in the
overlap.area at the top of the sheet at 12-inch.o.c.
For Valleys and Ridges: Cut underlayment into 4 to.6 foot lengths.Peel-the release paper and center sheet
over valley or ridge. Drape and press sheet into place, working from the center-of-the valley or ridge in
each direction. For valleys,apply the sheet starting at thelowest point and work upward.
6.3.3 Tile Applications(Tri-Built S/A HTTU Underlayment only):
Reference is made-to FRSA/TRI April 2012 (04-12) Installation Manual .and Table 1 herein, using the
instructions:noted above as a guideline.
Tile shall be loaded and staged in a manner that prevents tile slippage and/or damage to the
underlayment.
Exterior:Research and Design,LLC_ Evaluation Report A42960.10.12-R3
Certi lcate of Authorfmdon#9503 FL16048-113
Revision 3:10/08/2015
Page 4 of 5
TI UNITY I ER®
7. BUILDING PERMIT REQUIREMENTS-
As required by the Building Official or Authority Having Jurisdiction in,order to properly evaluate the installation of
this product.
8. MANUFACTURING PLANTS:
Contact the noted QA agency for information on product locations covered for F.A:C.Rule 9N-3 QA requirements.
9. QUALITY ASSURANCE ENTITY;
UL,LLC—QUA9625;(314)578-3406;k.chancellor@us.ul.com
-END OF EVALUATION REPORT=
Exterior Research and Design,LLC_ Evaluation Report A42960.10.12-113
CerQlcate of Authorization#9503 FL16048-R3
Revision 3:10/08/2015
Pages of 5