HomeMy WebLinkAboutProduct Approval (2) DETAIL B
OVERALL DIMENSIONS AND NAILING PATTERN
low 39-3/8"
(1m)
14-1/2"-17-1/2" 14-1/2'-17-1/Z'
(368-445mm) (368-445mm)
ail guide line
9-1/2" 6-1/2"-9-1/2"
(165-241M) (165-z41—)
13
337mm (146mm-159mm)
RZ-2-1rz' from bottom of shingle
(13-
el seal
adhesive
if ron back
ENHANCED NAILING PATTERN -six nails per shingle*
required by some local codes and required for enhanced wind coverage on certain products.
See limited warranty for details.
These shingles MUST be nailed a nominal 6"(152mm)from bottom of
of shingle, above the cut outs, as shown. Nails must not be exposed.
END OF THIS ACCEPTANCE
NOA No.: 13-0419.04
MAMI•UAD6 couNTY Expiration Date:02/21/17
Approval Date:07/11/13
Page 6 of 6
INSTALLATION
1. Shingles shall be installed in compliance with Roofing Application Standard RAS 115.
2. Flashing shall be in accordance with Roofing Application Standard RAS 115
3. The manufacturer shall provide clearly written application instructions.
4. Exposure and course layout shall be in compliance with Detail W,attached.
5. Nailing shall be in compliance with Detail W, attached.
LABELING
1. Shingles shall be labeled with the Miami-Dade Seal as seen below,or the wording"Miami-Dade County
Product Control Approved".
QMIAMMID�ADECOUMN
BUILDING PERMIT REQUIREMENTS
1. Application for building permit shall be accompanied by copies of the following:
1.1 This Notice of Acceptance.
1.2 Any other documents required by the Building Official or the applicable code in order to properly
evaluate the installation of this system.
NOA No.: 13-0419.04
MwMMAoE couNnr Expiration Date:02/21/17
Approval Date: 07/11/13
Page 4 of 6
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub-Category: Asphalt Shingles
Materials Laminate
Deck Type: Wood
SCOPE
This approves GAF Timberline HD®,Timberline Natural Shadow, and Timberline American Harvest®Shingles as
manufactured by GAF as described in Section 2 of this Notice of Acceptance.
PRODUCT DESCRIPTION
Product Dimensions Test Product Description
Specifications
GAF Timberline HD® 131/4"x 393/8' TAS 110 Fiberglass reinforced heavy weight asphalt
Manufacturing roof shingle,with a laminate profile
Locations#1,2,3,4,5,6,7,8
GAF Timberline Natural 131/4"x 393/8' TAS 110 Fiberglass reinforced heavy weight asphalt
Shadow roof shingle,with a laminate profile
Manufacturing
Locations#1,2,3,4,5,6,7,8
GAF Timberline®American 131/4"x 393/8' TAS 110 Fiberglass reinforced heavy weight asphalt
Harvest® roof shingle,with a laminate profile
Manufacturing
Locations#2,5,6,7,9
MANUFACTURING LOCATION
1. Tampa,FL
2. Michigan City, IN
3. Mobile,AL
4. Baltimore,MD
5. Myerstown,PA
6. Ennis,TX
7. Tuscaloosa,AL
8. Dallas,TX
9. Fontana,CA.
NOA No.: 13-0419.04
Mwr�l•DADE COUNTY Expiration Date:02/21/17
Approval Date:07/11/13
Page 2 of 6