HomeMy WebLinkAboutProduct Approval I
A
Aq_ I�a'a I �' TEAh7 KORNER.
I Company
swuaoucvaaus..w�uau�eos � nnp!eyezwmau
I
AquaCal'
InstallationManual
II
HEATWAVE
I.
I ,
I
y
SWIMMING POOL /SPA HEAT PUMPS
0
I i
I
I
I
Important
j Read this document before operating/installing this product
For additional product manuals and operation/installation procedures,please visit www.AquaCal.com
Lis
MODEL ! SERIAL NUMBER
LTM0098 REV 1
I:
I
Overhead Clearance
I
I' 1
Oveitiang_ wAh
gutter
OVERHEAD
5-feet
Rain run-off and [152 an]
I sprinklersshouldbe.
directed away from heater,
I j -
i '
I
HeatWave SuperQme&and TropiCal®(Top View) {
BACK
6 inches-
[1.5 cm] j
i
I
SIDES. SIDES
1 foot T.foot .
[30=cm]
[30 aril
FRONT
3 feet
[91 CM]
i
3.3 b V{TaterFlow:Rates °. .
Maintain water flow rates as indicated.Please note,these specifications relate to the heat pump only. Code-
specified whole system turnover rates must be satisfied.
z�h CAUTION-Failure to heed the following may result in equipment damage.
. Water flow exceeding maximum flow rate may damage heat exchanger,such damage will not be covered under
the equipment warrai Ly
i
i
Page-6
� I
'�������1�JY� -5 i '�r"'E"•.�,+�,4 ,ter-tx�.,�'_.� .' �. ��'r. ..a,'C,a k- � -±(,fir;�,.-t-P•-rak5'.shz�-+�c�� j
I
®R!
o> rollmg=I�riga#o�a
. Irrigation water may damage heat pump components.Have irrigation water directed away from the heat pump.
. The heat pump will withstand normal rainfall.Do not allow a roof slope to direct rainwater onto the heat pump.
Have a gutter installed on the roof edge to direct this water away from the heat pump. Or install the heat pump in
another location.
:< 1i1
-0000, 10
aQn,`- ._ :
r
Zt
The heat pump can produce a large amount of water in the fora of condensafion.The amount of water
depends on air temperature and humidity. j
is Install the heat pump with enough height to allow for water drainage.
is Plan for water drainage disposal as needed
� onntiog�.'�dReglourements r `�` rY - _ _
Build the heat ad out of concrete or another code-approved material.
pump p aPPm
Confirm the pad can support the weight of the heat pump. See"Weights"on page 40.
Elevate the pad enough to allow for drainage.
Make sure the pad is flat and level.
i
Have the pad extend at least 6 inches from the heat pump base in all directions.:
I ,
1. Do not install the heat pump on soil or grass.
40 Do not allow the heat pump base to touch the buildings foundation.
j Do not place the heat pump directly on a concrete floor inside a building.This can cause noisy equipment
j vibration.Install vibration dampeners betweenthe heat pump base and floor. .
Equipment pad must meet all requirements of authorities having code-related jurisdiction.
-
. Follow all applicable local,state, and national requirements regarding wind load anchoring.
The shipping brackets used to fie the heat pump to the pallet are approved mou (hurricane)brackets.They
i can be used to anchor the heat pump to the pad.
• If needed, contact AquaCar Customer Support to obtain the correct anchoring kit information.Please have the
heat pump model number and serial number when requesting support. See"Identifying Model Specifications"on
page 39.
I
3-3 �_:
a Clearances
Proper air circulation is required for the heat pump to operate efficiently.Avoid placing objects near or on top of
the heat pump.This includes shrubbery and lawn furniture.Time objects will also hinder maintenance access.
. Avoid storing chemical containers new the heat pump.The chemicals can cause equipment damage-
. � �!
I
i
I
' li
I
I .
I
� II
Page-:5