HomeMy WebLinkAboutProduct Approval EXTERIOR RESEARCH&DESIGN,LLC.
Certificate of Authorization#9503
353 CHRISTIAN STREET,UNIT#13
nINITY ERD OXFORD,CT 06478
PHONE:(203)262-9245
FAX:(203)262-9243
EVALUATION REPORT
Owens Corning Evaluation Report 037940.02.12-R7
One Owens Corning Parkway FL10674-1112
Toledo,OH 43659 Date of Issuance:02/06/2012
Revision 7: 04/18/2016
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein.have been evaluated for compliance with the 5th Edition (2014) Florida Building Code
sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 8.
Prepared by:
"Si
a -•'•Irk'%
- A,,,. The facsimile seal appearing was authorized by Robert Nieminen,
Robert J.M.Nieminen,P.E. '''S��ou a��;,., ; P.E.on 04/18/2016.This does not serve as an electronically signed
` �J,+++++'t rrt`s+ document.Signed,sealed
Florida Registration No.59166,Florida DCA ANE1983 hardco lg P'es have been transmitted to the
Product Approval Administrator and to the named client
CERTIFICATION OF INDEPENDENCE:
1. Trinity IERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinityl ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E.does not have, nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity]ERD nor Robert Nieminen, P.E. are, in any way,the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
ROOFING SYSTEMS EVALUATION: ��TRINITYIERD
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated
compliance with the following sections of the Florida Building Code and Florida Building Code, Residential Volume
through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements
and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1507.2.5,R905.2.4 Physical Properties ASTM D3462 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2008
3. REFERENCES:
Entity Examination Reference Date
UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007
UL LLC(CER9626) Physicals&Wind Resistance 20120516-112453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various
UL LLC (QUA9625) Quality Control Service Confirmation,R2453 Exp.08/20/2017
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Classic'and Suprem�ere fiberglass reinforced,3-tab asphalt roof shingles.
4.1.2 Berkshire are fiberglass reinforced,4-tab asphalt roof shingles.
4.1.3 Devonshire'."are fiberglass reinforced,5-tab asphalt roof shingles.
4.1.4 Duration, TruDefinition® Duration', Duration' Premium Cool, TruDefinition® Duration Designer Color
Collection, TruDefinition Oakridge®, Oakridge® and WeatherGuard� HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.2 Berkshire® Hip & Ridge Shingles, High Ridge, WeatherGuard® HP Hip & Ridge Shingles, ProEdge Hip & Ridge
Shingles and DuraRidge'"Hip&Ridge Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles.
4.3 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
5. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory
for fire ratings of this product.
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 FL10674-R12
Revision 7:04/18/2016
Page 2 of 8
QOTRIN'ITYIERD
5.4 Wind Classification:
5.4.1 All Owens Corning shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and
R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for
use in all wind zones up to Vasd= 150 mph (Vast= 194 mph). Refer to Section 6 for installation requirements
to meet this wind rating.
5.4.2 All Owens Corning hip&ridge shingles,Starter Strip Shingle and Starter Strip Plus noted herein are Classified
in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161,Class F,indicating the shingles are
acceptable for use in all wind zones up to Vasd=150 mph (Vast=194 mph). Refer to Section 6 for installation
requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category B or C and a building height of 60 feet or less.
Calculations by a qualified design professional are required for conditions outside these limitations. Contact
the shingle manufacturer for data specific to each shingle.
5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building
Code and F.A.C.Rule 61G20-3.
6. INSTALLATION:
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 61G20-3,per FBC Sections-1507.2.3, 1507.2.4 or R905.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using
minimum four (4) nails per shingle in accordance with FBC Sections 1507.2 or R905.2, with the following
exceptions:
➢ Berkshire®shingles require minimum five(5)nails per shingle.
➢ WeatherGuard®HP shingles require minimum six(6)nails per shingle.
➢ Devonshire'"shingles require minimum six(6)nails per shingle.
➢ Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. See figures below for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
Felt underlayment Deck Feltundaiaymem Deck Seg-adhered
WeatherLackB
Self-adhered unde layment
WeatherLocke
underlayment
Drip edge
Drip_ Drip edge Drrip01
—
9 9
Nails kxated
Nails located from eave
2=3"from
we
Instellfirst Self-sealing adhesive Inst�first SmrterStrip Plrs Salf�eafingadhesive
Starter Strip positioned along eave with 6'removed positioned along eave
shingle with `\
6"removed \ h gtarterStri Plusoverhangseavesandrakes1W-3/4"
Starter Strip shingle overhangs eaves and rakes/i'—a/i" p
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 FL10674-R12
Revision 7:04/18/2016
Page 3 of 8
ERD
TRINIIY I
6.2.6 Minimum Nailing—Classic®&Supreme:
Normal Mansard or Area pans Normal Mansard or Ana.pars
Wind Anes, High Wind desvannsy Wind Areas High Wind desvanes v
Area para vientos nomrtales Areas vientos fuertes Area para vientos nonneles Areas vierrtos finites
03 z r. zt _ (AI tzt �•� �� z•. (BI' z' �',
.. . . . .
W Exposure 6 6/8"Exposure
Exposieidn Exposlei6n
6.2.7 Minimum Nailing—Berkshire®:
a�rtt gip. Sulam strip
..ia lka da seBadav La tka dewflador
0-0
B YP 9 Yt' 9 Yt 8th } ,e'n" a Vt" a Vi" 8%.
}
tu:
r
r
Standard Fastening Pattern 6-Nail Fastening Pattern
SealarR strip
!afire da saradir
r. t.
'r
it
2" AsphaR.ropfingceeierit
Cemeato de tecdoda asrafts.
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-117
Certificate of Authorization 119503 F1.10674-1112
Revision 7:04/18/2016
Page 4 of 8
TRINITY I'ERD
6.2.8 Minimum Nailing—Devonshire+":
7" 8" 8" 8" 7"
n
,• N w
chem
Nails
53/8'exposure Sealant location }"
Exposld6n de 5.518 ping Ubicad6n del sellador �,• B
Ten 1"Spots of Asphalt Roof Cement
Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern
6.2.9 Minimum Nailing—Duration®,TruDefinition® Duration, Duration® Premium Cool &TruDefinition® Duration•
Designer Color Collection:
4-Nall Fastening Fattem .6-Nall Fastening Pattem
Su•tlanfastnNparwavMQth - SuraNaaa fasten"arcawmm
Nag.TYW.W Nair Typtol
+ +r +r' I +r r
a.^c�:a r•.++' •e F� F]Nom•--o • • s..®c�ec...�,i • ��•�o so.«.c•.w>•.wr• •.
FA.
e-va'a-Bit^ sve•B•BrB^
rym.. rnw�nF1 F� E
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Siopea Greater Than 21:12
Su 11,1*119anlnearea•Aslh
. tUA,+YPM+1
+• +Y 1Y
havfusyt"..0 • • •o•.ev�yw
Pom 7•Sp•n NAephtll RoofNe Cernso!
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-117
Certificate of Authorization#9503 FL10674-1112
Revision 7:04/18/2016
Page 5 of 8
QOTRINITYIERD
6.2.1 Minimum Nailing—TruDefinition'Oakridge®,Oakridge®:
4:Nall Pattom 6 Nail Paltent•
.Fs 0 a con 4 claws. Esguema can 6 clavos
1' r:
12 -�1
66/Q-Exposure Nail 5518"Exposure. Naffs
ExposieiBirde55%Spuf9 Clavos Ek*ricbnde;5518pulg. 56]8"'Exposure Clavos 66/S"Exposure:
Fxposiucrt dd 55/8pulg fipo§ielce de 66/8 pulg.
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastenlnp for Slopes Greater Than 21:12
BuefWIH fcbning ons v.Mtlt
Na Totem
r m +r r
o-+re•o-sm^
'—t^Spot cf/bpMft RooUU C=wd
Mansard or Steep Slope Fastening Pattern
6.2.1 Minimum Nailing—WeatherGuard®HP:
I Slagle Ode Vbw.
_. vZois hmiw
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 FL10674-R12
Revision 7:04/18/2016
Page 6 of 8
Q0TRJN1-1YIERD
6.3 Hip&Ridge Shingles:
6.3.1 Installation of Berkshire Hip and Ridge Shingles, High Ridge, WeatherGuard' HP Hip and Ridge Shingles and
ProEdge Hip&Ridge Shingles shall comply with the manufacturer's current published instructions,using four
(4) nails per shingle. Installation of DuraRidgell Hip & Ridge Shingles shall comply with the manufacturer's
current published instructions, using two (2) nails per shingle. Refer to Owens Corning published
information on wind resistance and installation limitations, including the use of hand-sealing for wind
warranties.
6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berkshire®Hip&Ridge and High Ridge:
FIgrQ 4'
Fig.2:
A
E—.PnDketllan-
arellvIDNMd Tcp%he . SIUeYevi"
' '
Nails —j A 'Haas- Naps
4"
_ r"r .TaP.�antriaiea r �
A I I 4• Piece;
9' I I.
I 1 j I 1
p 1 1 I I I
p l i j I 1
i i. r r • '
�0.SUfB . I
i
I
I
I
6.3.4 Minimum Nailing—WeatherGuard®HP Hip and Ridge:
Fig.C Hip•&_Ridge Shingle Fastening
Fig.'A .9T Tepvlew
Prerallltlg Wlnq
�—Dlrxtbn A ..
A
Nails� --)q T
Nails Nails
I
2" 2.
I I I I
Etposure
S" EYposure
It 12"
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-117
Certificate of Authorization#9503 FL10674-1112
Revision 7:04/18/2016
Page 7 of 8
��TRINITYIERD
6.3.5 Minimum Nailing-ProEdge Hip&Ridge Shingles:
Prevailing Standard
Wind Direction Saalant Strip PatterFastening
8'Exposure • !,� i�l ISP
• 12• 1 Sealant
Fasten 7% 711? B"Exposure
Cover Exposed 1
Fasteners with I-
Roof Cement I�12•�
SII
6.3.6 Minimum Nailing—DuraRidgeT"" Hip&Ridge Shingles:
Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer to Owens Corning
published installation instructions for their minimum requirements.
FraraifngWir d Dirocdm We enipGn
D..ch odomi.taduTwt
Dirard6ndef Amb pradomimnm i- vlstasuper6or i
Gou
1
dens Caring SumlJair • ane
d
A J b i ti Im
E
F �IZ
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC—QUA9625; (414)248-6409;karen.buchmann@ul.com
END OF EVALUATION REPORT-
Exterior
EPORT-Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 FL10674-R12
Revision 7:04/18/2016
Page 8 of 8