HomeMy WebLinkAboutproduct approval l �
I,
I i
iEXTERIOR RESEARCH&DESIGN,LLC.
Certificate of Authorization#9503
353 CHRISTIAN STREET,UNR#13
TRINITY J ERD l OXFORD,CT 06478
PHONE:(203)262-9245
FAX:(203)262-9243
_ EVALUATION REPORT
GAF Evaluation Report 01506.01.08-1121
1 Campus Drive FL10124-R19
Parsippany,NJ 07054 Date of Issuance:01/03/2008
Revision 21:09/26/2016
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules'and regulations governing the use of
construction materials in the State of Florida.The documentation submitted has beeneviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Cade, Residential Volume. The
products described herein have been evaluated for compliance with the StWIEdition (2014) Floiida Building Code
sections noted herein.
DESCRIPTION: GAF Asphalt Roof Shingles
LABEUNG: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Cade that',relate'to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen,P.E.if the
product changes or the referenced Quality Assurance documentation changes. Trinity I ERD requires a complete
review of this Evaluation Report relative to updated Code requirements with ealch Code Cycle.
ADVERTISEMENT:The Evaluation Report number preceded by the words"TrinitylERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION:Upon request,a copy of this entire Evaluation Report shall be provided to the usei by the manufacturer or
Its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 6.
Prepared by: U,Stntnuy,�—
Mxrtf
ii C- tie-s9teb ':�
�`9 •-SSA.—. %W�;
k 01
Robert J.M.Nieminen P.E. y. �4
s+ ll+efacshnlleseal appearingwisautharizedbyRobert Nkm'uteri
i ,�,1S�flVat- i", • PSonDS/NrAl6. es
Thlsdonotsenreasanelectronintysl ed
J,,.uuua �
Florida Registration No.59166,Florida DCA ANE1983 tom_ document.slgn, sealed hardeoples have beentransmitted to the
Product Approval Administratorand to the named client
CERTIFICATM OF INDEPENDENCE: i
1. TrinitylERD does not have, nor does it Intend to acquire or will it acquire, a financial interestlin any company manufacturing or
distributing products it evaluates. {
2. Trinity I ERD Is not owned,operated or controlled by any company manufacturing or distrlbutingproducts it evaluates,
3. Robert Nieminen,P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued. ,
4. Robert Nieminen,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
'i
5. This,is a building code evaluation. Neither Trinity ERD nor Robert Nieminen, P.E.are,in any way,the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof,is/was used for permittingor design guidance unless retained
specifically for that purpose.
I ,�
I
ERD
TRINITY I
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: GAF Asphalt Roof Shingles,as produced by GAF, have demonstrated compliance with the
following sections of the Florida Building Code and Florida Building Code, Residential Volume through testing in
accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations/
Conditions of Use set forth herein.
2. STANDARDS:
Section ProRe :Standard Year
1507.2.4,R905.2.3 Physicai,Properties ASTM-D1970 2009
1507.2.5,R905.2.4 Physical Properties. ASTM D3462 2009
1507.2.7:1,8905.2.6.1 Wind Resistance ASTM D3161 2009
1507.2.7.1,R905.7.6.1 Wind Resistance ASTM D7158 2008
1507.2.7.1,8905.2.6.1 Wind Resistance TAS 107 1995
3. REFERENCES:
Entity' Examination. :Reference, Date
GAF(PDM 1915) Letter of Equivalency Seal-A-Ridge Impact Resistant IR 01/13/2012
PRI(TST 5878) Physical Properties GAF-025-02-01 03/27/2002
PRI(TST 5878) ASTM D3462 GAF-059-02-01 09/02/2004
PRI(TST 5878) ASTM D3462 GAF-080-02-01 05/25/2005
PRI(TST 5878) Physical Properties GAF-324-02-01 12/01/2011
PRI(TST 5878) Wind Driven Rain GAF-407-02-01 01/21/2013
UL(TST 1740) ASTM D3462 93NKS295 11/29/1993
UL(TST 1740) ASTM D3462 99NK43835 01/12/2000
UL(TST 1740) TAS 107 94NK9632 03/29/2600
UL(TST 1740) ASTM D3462 01NK06632 02%02/2001
UL(TST 1740) ASTM D3161,TAS 107 01NK9226 05/21/2001
UL(TST 1740) ASTM D3161 01NK37122 12/18/2001
UL(TST 1740) ASTM D3462 OINK37122 12/19/2001
UL(TST 1740) ASTM D3161,TAS 107 02NK12980 04/10/2002
UL(TST 1740) ASTM D3161,TAS 107 02NK30871 09/09/2002
UL(TST 1740) ASTM D3161 03CA5367 03/11/2003
UL(TST 1740) ASTM D3462 03NK26444 10/17/2003
UL(TST 1740) ASTM D3462 04NK13850 06/07/2004
UL(TST 1740) ASTM D3161 04NK13850 06/23/2004
UL(TST 1740) ASTM D3161 04NK30546 03/10/2005
UL(TST 1740) ASTM D3462 04NK22009 DS/06/2005
UL(TST 1740) ASTM D3161 04NK22009 05/09/2005
UL(TST 1740) ASTM D3462 OSNK27924 D2/10/2006
UL(TST 1740) ASTM D3161 OSNK27924 02/11/2006
UL(TST 1740) ASTM D3161,D3452 06CA18077 06/05/2006
UL(TST 1740) ASTM D3161,D3462 06CAIS074 06/16/2006
UL(TST 1740) ASTM D3162,D3462 06CA35251 10/18/2006
UL(TST 1740) ASTM D3462 06CA31603 12/01/2006
UL(TST 1740) ASTM D3161,D3462 06CA41095 12/27/2006
UL(TST 1740) ASTM D3161 07NK05228 03/13/2007
UL(TST 1740) ASTM D3161 06CA31611 04/04/2007
UL(TST 1740) ASTM D3161 06CA61148 04/09/2007
UL(TST 1740) ASTM D3161,D3462 07CA31742 11/08/21007
UL(TST 1740) ASTM D3161,D7158,D3462 08CA06100 03/13/2008
UL(TST 1740) ASTM D3161,D3462 07CASS908 04/01/2008
Exterior Research and Design,U.C. Evaluation Report 01506.01.08-1121
Certifhcate of Authorization#9503 FL30124-R19
Revision 21:08/26/2016
Page 2 of 6
i
f ,
` I
QTRRINIWIERD
Entity Examination, Aderence: ,.� Date
UL[TST 1740) ASTM D3161,D3462 09CA10592 03/26/2009
UL(TST 1740) ASTM D3161,D3462 09CA06856 { ! 05/15/2009
UL(TST 1740) ASTM D3161,D7158,D3462 09NK06647 08/01/2009
UL(TST 1740) ASTM D3161,D7158,D3462 09CA27281 I 08/27/2009
UL(TST 1740) ASTM D3161,D7158,D3462 10CA35554 ! 03/05/2010
UL(TST 1740) ASTM D3161,D7158,D3462 10CA23686 p ! 05/15/2010
UL(TST 1740) ASTM D3462 10CA07264 05/27/2010
UL(TST 1740) ASTM D3462 IOCA11953 10/29/2010
UL(TST 1740) ASTM D3161,D7158,D3462 1ONK12951 10/30/2010.
UL(TST 1740) ASTM D3161,131158,D3462 IONK12070 11/04/2010
UL(TST 1740) ASTM 03161,D7158,D3462 08CA06100 01/30/2010
UL(TST 1740) ASTM D3161,D7158,D3462 10CA53934 03/31/2011
UL(TST 1740) ASTM D3161,D7158,D3462 11CA48924 10/22/2011
UL(TST 1740) ASTM D3161,D7158,D3462 IICA47919 12/03/2011
UL(TST 1740) ASTM D3161,D7158,D3462 11CA48408 y ! 12/08/2011
UL(TST 1740) ASTM D3161,D7158,D3462 11CA48725 12/09/2011
UL,LLC.(TST 9628) ASTM D3462 12CA34891 F f 10/12/2012
UL,U.C.(TST 9628) ASTM D3161,07158,D3462 12CA58151 f ! 02/15/2013
UL,U.C.(TST 9628) ASTM D3161 12CA38083 02/26/2013
UL,U.C.(TST 9628) ASTM D3161 13CA32332 ,� 06/18/2013
UL,I.I.C.(TST 9628) ASTM D3161 13CA37934 14 08/02/2013
UL,LLC.(TST 9628) ASTM D3161,D7158,.D3462 4786875675 .G 07/17/2015
UL,I.I.C.(TST 9628) ASTM D3161,D7158,D3462 4787434542 A ;j 05/17/2016
UL,LLC..(QUA 9625) Quality Control Inspection Report,R21,Mobile,ALi 12/28/2015
UL,I.I.C.(QUA 9625) Quality Control Inspection Report;R21,My'rstowh PA 02/23/2016
UL,LLC(QUA 9625) Quality Control Inspection Report;R21,Tui aaloosa AL 02/26/2016
UL,U.C.(QUA 9625) Quality Control Inspection Report R21,Michigan Cty,IN 03/02/2016
UL,U.C.(QUA 9625) Quality Control Inspection Report;R21,Shafter,CA 02/18/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report;R21,Savannah,GA 02/24/2016
UL,I.I.C.(QUA 9625) Quality Control Inspection Report;R21,Minneapolis,MN 02/09/2016
UL,I.I.C.(QUA 9625) Quality Control Inspection Report;R21,Mt.,Vernon,IN 02/09/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report;R21,Bali lmore,'MD 03/01/2016
UL,U.C.(QUA 9625) Quality Control inspection Report,'R21,Tampa,FL 02/29/2016
UL,LLC(QUA 9625) Quality Control Inspection Report;R21,Dallas,TX ' 02/17/2016
UL,LLC(QUA 9625) Quality Control Inspection ReportI R21,EnA6,TX ' 02/03/2016
UL,LLC(QUA 9625) Quality Control Inspection Report;R21,Fontlana,CA 03/03/2016
4. PRODUCT DESCRIPTION:
4.1 Asohalt Shingles:
4.1.1 Marquls® WeatherMaxs, Royal Sovereign® and Sentinel® are a fiberglass reinforced 3-tab asphalt roof
shingles.
4.1.2 Camelot®, Camelot® II, FortitudeT", Glenwood', Grand Canyon!;, Grand,!Sequoias, Grand Sequoias IR,
Grand Sequoia® ArmorShieldm, Monaco®, Sienna"°, Timberline® American Harvest®, Timberline®
ArmorShieldTm II,Timberlines Natural Shadow®,Timberline HDs,Timberline'Cool Series®,Timberline Ultra
HDs and Woodlands are fiberglass reinforced,laminated asphalt roof shingles.
4.1,3 Slateline®is a fiberglass reinforced 5-tab asphalt roof shingle.
4.2 Hip&Rldee Shinsles:
4.2.1 Seal-A-Ridge® Ridge Cap Shingles, Seal-A-Ridge® IR Impact-Resistant Ridge Cap Shingles, Seal-A-Ridge®
ArmorShield-Ridge Cap Shingles and Timbertex° Premium Ridge Cap Shingles are fiberglass reinforced,hip
and ridge asphalt roof shingles.
i
Exterior Research and Design,LLC. Evaluation Report 01506.01.08-R21
i}I
CertM of Aothorliatki;99503 l i I I FL10124-R19
Revision 21:08/26/2016
Page 3 of 6
i
0
TRINITY l ERD
4.3 AccessdrV.Starter Striris:
4.3.1 Pro-Start®Eave/Rake Starter Strip Shingles and WeatherBlocker'Premium Eave/Rake Starter Strip Shingles
are starter strips for asphalt roof shingles.
4.3.2 QuickStart® Peel & Stick Starter Roll is a is a mineral-surfaced, fiberglass-reinforced, self-adhering SBS
modified bitumen starter strip,nominal 9-inch x 33 ft roll,for use with asphalt shingles wiWexposure of 6-
inch or less.
4.3.3 StarterMatchT"Sharter Strip Shingles are color-coordinated starter strips for use with Grand Canyon® and
Grand Sequoia® series asphalt shingles. StarterMatch"' are installed as the second starter for Grand
Canyon®and Grand Sequoia®series installations.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in anyway, the
Designer of Record for any project on which this Evaluation Report, or,previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials
Directory for fire ratings of this product.
5.4 Wind Classification:_
5.4.1 The GAF asphalt shingles noted in Section 4.1 are Classified in accordance with FBC Tables 1507.2.7.1 and
R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158,Class H, indicating the shingles are acceptable for
use in all wind zones up to Vwd=150 mph(V„n=194 mph). Refer to Section 6 for installation requirements
to meet this wind rating.
5.4.2 The GAF hip&ridge shingles noted in Section 4.2 are Classified in accordance with FBC Tables 1507.2.7.1
and R905.2.6.1 to ASTM D3161,Class F,indicating the shingles are acceptable for use in all wind zones up to
Va,d=150 mph(V„k=194 mph). Refer to Section 6 for installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies only to exposure category B or C, as defined in FBC 1609.4.3, and a
mean roof height of 60 feet or less. Calculations by a qualified design professional are required for
conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building
Code and F.A.C.Rule 61G20-3.
6. INSTALLATION:
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to GAF and shall hold current Florida Statewide Product Approval, or be
Locally Approved per Rule 61G20-3,per FBC Sections 1507.2.3,1507.2.4 or R905.2.3.
6.2 Starter Shingles or Starter Strip:
6.2.1 Installation of Pro-Start Eave/Rake Starter Strip Shingles, WeatherBlocker Premium Eave/Rake Starter Strip
Shingles and QuickStart Peel&Stick Starter Roll shall comply with the GAF current published instructions.
6.3 Asphalt Shingles:
6.3.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using
minimum four (4) nails per shingle in accordance with FBC Sections 1507.2 or R905.2, with the following
exceptions:
Camelot,Camelot II,Grand Canyon,Grand Sequoia,Grand Sequoia IR,Grand Sequoia ArmorShield,and
Woodland require minimum five(5)nails per shingle.
➢ Slateline requires minimum six(6)nails per shingle.
Exterior Research and Design,I.I.C. Evaluation Report 01506.01.08-1121
Cerd/lcate ofAuthorizotlon#9503 FL30124-1119
Revision 21:08/26/2016
Page 4 of 6
N\j
TRINITY!ERD
6.3.2 Fasteners shall be in accordance with manufacturer's published requirements,but not less than FBC 1507.2.6
or•R905.2.5. Staples are not permitted.
6.3.3 Where the roof slope exceeds 21 units vertical In 12 units horizontal, special 'methods of fastening are
required. Contact the shingle manufacturer for details. !
6.4 Hip&Ridge Shingles:
6.4.1 Installation of Seal-A-Ridge Ridge Cap Shingles,Seal-A-Ridge IR Impact-Resistant Ridge Cap Shingles and Seal-
A-Ridge ArmorShield Ridge Cap Shingles shall comply with the manufacturers current published instructions
with a minimum two(2)nails,minimum 3/8-inch head diameter,per shingle and riominal 0.25-inch diameter
beads of Henkel"Loctite PL S30 Roof&Flashing Sealant".
Seadant
11.5'
Senante •
(2sffn) (25 mm)' Enduit d'dtanchM
J, ;
4ay 1
Nail
(305 mm)
'
Claw.
6g 5 T,i 7 g)l CloverLi
{188-194 mm)
I
— I
(3 12
nun)
6.4.2 Installation of Timbertex Premium Ridge Cap Shingles shall comply with the manufacturer's current
published instructions with a minimum two (2) nails, minimum'3/8-inch'!head diameter, per shingle and
beads of Sonneborn NPI Gun Grade Polyurethane Sealant or Henkel PL Roofing and Flashing Sealant.
%V aftm
tinea} rnf (211 nim
Is '
MR) (aa5mm) j.
9" �Cbuor
l2M ram
1 ,
tx
l�rtr�)
6.4.3 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted. I'
• I
Exterior Research and Design,I.I.C. Evaluation Report 01506.0L08-11121
Certlfkate of AUdWilation 09503 FU0124-Ri9
Reviiton 21:08126/2016
Page 5 of 6
O
TRINITY I ERD
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed In FBC
Table 1507.2.7.1/R905.2.6.1.
S. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 61G20-3 QA
requirements. at,
10. QUALITY ASSURANCE ENTITY:
UL LLC—QUA9625;(847)664-3281
END OF EVALUATION REPORT-
Exterior Research and Design,LLC. Evaluation Report 01506.01.08-R21
Cerdflcute ofAuthorkatfon 09503 F1.30124-1119
Revision 21:08/26/2016
Page 6 of 6
i
Certificate`of Authorizatign No. 29824'
CREEK17520 Edmburgh.Drive,
.� j Tampa,FL33647
TECHNICAL SERVICES, LLC + (813)480=3421
EVALUATION REPORT FLORIDA BUILDIN`
i
G" CODE,5T":EDITION(201.$)
`Manufacturer: TAMKO BUILDING PRODUCTS, INC. i j Issued August 22, 2016'
P'A,Box 1404
Joplin,.MO 64802
.(417)624-6644 j
http://www:tatnko.dom i
i 1 '
.Quality Assurances ULiLLC,(QUA9625)
� I
i I
,SCOPE' J
Category: Roof ng
.Subcategory: Underlayments s
Code Se24ctions: 1507.2 3, 1507 , 1507.2.8',,1507.2:9.2, 1.507:3:3,'1507.4.5.1, 1507 4.5.2, 1507.4.5:3,
15075.3, 1507,5;32; 1507..6:3„15.07;6:3.2,,1507:615, 1507:7:3, 1507 7.$.2;1507.8.3,.
-1507.8.3.2, 1507.8-.8,T15078,1507.9:3, 1507 9:3.2, 1507.9.5, 1507.9.9
Properties: Physical properties
I J
'REFERENCES I
Entity
Report No. (StandardYear
PRI Construction Materials Technologies(TST6049) TAP-191-02-01 REV" ASTM D,1,970 2009
;PRI Construction Materials Technologies(TST6049) TAP=192-02-01 ASTM D 1970 2009
PRI Construction Materials Technologies(TST6049) TAP.=193.02-01 ASTM D 1970 2009
PRI Construction Materials Technologies(TST6049) TAP=214-02-01 ASTM D 4869 i 2005e01
PRI Construction Materials Technologies(TST6049) TAP-215.=02-01 ASTM D 226 2006
PRI Construction Materials Technologies(TST6049) TAP-216-02-03 ASTM D 6380 2003(2909)
PRI Construction Materials Technologies(TST6049) TAP7217-02 01;REV ASTM D 6380 1 2003(2009)
PRI Construction Materials Technologies(TST6049) TAP.=218-02=01 ASTM D 226 2006
PRI Construction Materials Technologies(TST6649) TAP=219-02-01 ASTM D 226 2006
PRI Construction Materials Technologies'(TST6049) TAP-220-02-01 ASTM D 6380 2003(2009)
,PRI Construction Materials Technologies(TST6049) TAP-222-02-01 ASTM D 4$69 2005e01
:PIR[Construction Materials Technologies(TST6049) TAP=319-02-01.1 ACC 188
UL LLC'(TST9628) 13CA12269 ASTM D'226 2006
.PRODUCT DESCRIPTION AND,APPOCATION, e
TAMKOO'ASTM Slate ASTM D 6380,,C_lass.M Type 11;undedayme
Surfaced .011 Roofn with asphalt and coated on both sides with asphaltsS d surfa m YAIth granules.g p ced with granules:
Min.,slope- 2:12 j
Application: The underlayment shali'be installed with minimum 2"
side laps,and mmimurW" staggered end laps and in
accordance with FRSA/TRI 07230 'for the
applications: ! ! I
i
Allowable roof coverings: Attachment of asphalt shingle valleys and Gay and
concrete tileshall be permitted in accordance with
the FBC.
I
q
T13P14001.3. F1.12328-137 Page 1 of,4
Technical Services,LLC of an ed for State of
ty asswrance changesthroug of the dura' n fm'w ich t6i if report
CREEK
P P product
y product Chan tion for�which this report is valid.
This evaluation repoIrt.does not express no imply•warranty,installation, recommended use,or other prod)ct attributes that are not•
specifically addressed:herein. ,
CREEK TAMKO BUILDING PRODCUTS,INCa:
TAMKO Undertayment,
TECHNICAL SERVICES, LLC'
TAMKOO ASTM Tile ASTM D 6380,Class M,Type II underlayment,eonstructed from,an org'anic1feltsatur9ted
Underlayment with asphalt then coated on both sides with asphalt and.surfaced with granules.
Application: The underlaWh nt shall be installed with minimum:2°
side laps and minimum 4":staggered'end.laps and in,
accordance with "FRSA/TRI 07230 for tile
applications:
Allowable rooficoverings: Attachment 0 clay and, concrete the "shall be
permitted in accordance with the FBC.
TAMKoO Master ASTM D.,638.0,Class-S,Type,IV uridedbymerit constructed.from an.organic felt saturated
Smooth with asphalt then coated ron both sides with asphalt and surfaced with a f ne mineral.
Application: The undedayment shall be installed along the valley
in accordance,with FBG requirements..
Allowable roof coverings:. Attachment of asphalt shingle valleys shall be
permitted In accordance with the FBC:
TAMKOO Moisture :Self-adhered,,ASTM D 1970, fiberglass reinforced', modified' bitumen sheet membrane .
Guard'PluS® with a mineral.surfacing and a,removable release.flm on the'adhesive Side.
Application: The underlayment :shall be attached by, adhering
directly .to .the roof deck with minimum 3-1177 side
laps:and minimum 6"staggered end laps.
Min.application temperature:. 400F,.
Allowable roof coverings: Attachment of asphalt shingles and .mechanically
fastened concrete and clay tile. roofing shall be
permitted in accordance-with the FBC:;
TAMKO®No:15.ASTM ASTM D 226,;Type I underlayment constructed from a non:perforated organic felt=that is
Asphalt Saturated saturated with asphalt.
Organic'Felt
Application; The'uriderlayment shall be installed with minimum,2"
side,laps,and minimum 4 end laps.
Allowable roof coverings: Attgchrhent of asphalt;shingles;.metal iroofing, wood
shingles; wood shakes, and. roll roofing shall be
permitted.in accordance with the FBC.,
TAMKO@)No.15 UL ASTM D 226;Type I underlayment constructed from a non-perforated organic felt that:is
Asphalt Saturated saturated.with.asphalt..
Organic Felt -
Application: The underlaymentshall be installed with minimum 2"'
side laps and minimum 4"end laps.;
Allowable roof coverings: Attachment of asphalt shingles, metal goofing;wood
shingles, wood shakes, and roll roofing shall be
permitted in accordance with the FBC.
TBP140013 FL12328-R7 Page 2 of 4
This evaluation.report is provided for State of Florida product approval under Rule 61020-3. The manufacturer shall notify,CREEK'.
Technical.Services,LLC of any,product changes or quality assurance changes throughout the duration for which this report;is valid.
This.evaluation report does not express nor imply,
po �qi Warranty, installation,recommended use,or otherproduct attributes that are not
specifically addressed herein.
CRK TAMP BUILDING PRODCUTS,.
INC,TAMKO Underlayments
TECHNICAL SERVICES, LLC
II
TAMKOO.No.30 ASTM ASTM D'226„Type I1 undeaa Y.
constructed from a non-perforated organic.felt that is.
Y _
Asphalt Saturated -saturated with asphalt
Organic.Felt
Application! The underlaymebt shall be installed with minimum 2”
side laps:and:minimum;4 end laps.
Allowable roof,coverings? Attachment of asphalt shingles, fetal roofing, clay
and concrete tile, slate shingles, wood shingles,
wood shakes;.and roll roofingi :shall be permitted.in
accordance�with the FBC.
f
ype II unde la fent constructed-from a non- i
TAMKO( No.30 UL ASTM D 226,T y perforated organic felt that is
Asphalt Saturated saturated with asphalt:
Organic Felt_
Application: The;underlaymI'nt shall1be installed with minimum 2"
side laps and minimum4''"end laps..
Allowable roof coverings: Attachment of asphalt'shingles, metal roofing, clay
and concrete file, slate shingles, wood, shingles,
wood shakes, and roll,hoofing shall'be permitted in
accordance-witli the FBC: i
TAMkCO TW Metal and Self.-:adhered, flexible-, ASTM D 1970,, rubberizeid asphalt sheet .membrane with. a
Tile Underlayment polymer film on the surface and a removable release film on the adhesive side.
Application:. The underlayment shall be attached by adhering
o the roof deck
directly ,_ ° °with minimum 4" side laps
t
and minimum 6!staggered end laps.
i
Min.application temperature: 40°F 1
Allowable roof coverings: Attachment, of asphalt "shingles, metal roofing, and
mechanically fastenedi clay and concrete tiles sha11
be permitted in la' ccorda'nce with the FBC
TAMKO®TW Self-adhered, flexible, ASTM D 1970, rubberizetl asphalt sheet membrane with. a
UndeHayment polymer film on the surface and a .removable release film oh the adhesive side.
Application: The underlayrrient shall be attached by adhering
directly to the roof deck with,'minimum: 4" side laps
and minimum 61 staggered end laps.
Min..application temperature: 40°F
_
Allowable roof coverings:, Attachment of Jasphali �shingleis and metal roofing
shall be permitted in accordance with the:FBC.
TAMKOO TAM-FELT Altemate-to,ASTM D 226,Type I and.Type 11 underlayment'constructed from a non
perforated organic felt that is saturated with asphalt. ! l
Application: The underlayment sha11',be installed with minimum 2"
side laps.and minimum'4"end'laps.
J i
Allowable roof coverings: Attachment of asphalt shingles shall be permitted-in
accordance with the FB.C.
1
i
. i
TBP14001..3. FL12328-R7 i
t i Page,3of4
This evaluation report is provided for State of Florida product approval under Rule 61'G20-3. The'manufacturer shall notify CREEK;
Technical'Services;L.LCof any,product changes or quality assurance changes throughout the duration for,which this report is valid,
This evaluation report does not express nor imply,warranty, installation,recommended use or other product attributes that are not.
specifically addressed herein.
I