HomeMy WebLinkAboutProduct Approval EXTERIOR RESEARCH &DESIGN, LLC.
FILECertificateof Authorization 119503
P-L 353 CHRISTIAN STREET, UNIT#13
TRINITY ERDC� OXFORD, CT 06478
PHONE:(203)262-9245
FAX:(203)262-9243
EVALUATION REPORT
Owens Corning Evaluation Report 037940.02.12-R7
One Owens Corning Parkway DEC 18 1011 YU FL10674-11112
Toledo,OH 43659 Date of Issuance:02/06/2012
..........
Revision 7: 04/18/2016
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code
sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity IERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 8.
Prepared by: �.,,►�t����rfn,,,,���
4P,. s4���/•
+ 7C'
•���•'�= ? ,.'r yJTThe facsimile seal appearing was authorized by Robert Nieminen,
Robert J.M.Nieminen,P.E. '� `r��03��L'�;•�� P.E.on 04/18/2016.This does not serve as an electronically signed
Florida Registration No.59166,Florida DCA ANE1983 ��'�""'t""` document.Signed,sealed hardcopies have been transmitted to the
Product Approval Administrator and to the named client
CERTIFICATION OF INDEPENDENCE:
1. TrinityJERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity I ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity)ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
TTPuNRYIERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated
compliance with the following sections of the Florida Building Code and Florida Building Code, Residential Volume
through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements
and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1507.2.5,R905.2.4 Physical Properties ASTM D3462 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2008
3. REFERENCES:
Entity Examination Reference Date
UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007
UL LLC(CER9626) Physicals&Wind Resistance 20120516-112453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various
UL LLC (QUA9625) Quality Control Service Confirmation,R2453 Exp.08/20/2017
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Classicf and Supreme®are fiberglass reinforced, 3-tab asphalt roof shingles.
4.1.2 Berkshire are fiberglass reinforced,4-tab asphalt roof shingles.
4.1.3 Devonshire—are fiberglass reinforced, 5-tab asphalt roof shingles.
4.1.4 Duration, Tru Definition" Duration', Duration' Premium Cool, Tru Definition" Duration' Designer Color
Collection, TruDefinitionx OakridgeF, Oakridge and WeatherGuardx HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.2 Berkshire Hip & Ridge Shingles, High Ridge, WeatherGuardR HP Hip & Ridge Shingles, ProEdge Hip & Ridge
Shingles and DuraRidge'" Hip& Ridge Shingles are fiberglass reinforced, hip and ridge asphalt roof shingles.
4.3 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory
for fire ratings of this product.
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 F1.10674-1112
Revision 7:04/18/2016
Page 2 of 8
TRINITY ERD
5.4 Wind Classification:
5.4.1 All Owens Corning shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and
R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for
use in all wind zones up to V,,d= 150 mph (V,,,t = 194 mph). Refer to Section 6 for installation requirements
to meet this wind rating.
5.4.2 All Owens Corning hip& ridge shingles, Starter Strip Shingle and Starter Strip Plus noted herein are Classified
in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the shingles are
acceptable for use in all wind zones up to V,sd= 150 mph (V,,t= 194 mph). Refer to Section 6 for installation
requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category B or C and a building height of 60 feet or less.
Calculations by a qualified design professional are required for conditions outside these limitations. Contact
the shingle manufacturer for data specific to each shingle.
5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building
Code and F.A.C. Rule 61G20-3.
6. INSTALLATION:
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval, or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using
minimum four (4) nails per shingle in accordance with FBC Sections 1507.2 or R905.2, with the following
exceptions:
Berkshire' shingles require minimum five(5)nails per shingle.
WeatherGuard�HP shingles require minimum six(6) nails per shingle.
Devonshire'"shingles require minimum six(6)nails per shingle.
Starter Strip Shingle and Starter Strip Plus require minimum five(5) nails per strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. See figures below for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
Feb undeelarment Deck Felt,ndeyymwd Deck
WeatlKrlod�
SeH•adhered Wrda WW—
WeatherLocke
undedayment
Drip edge
Drip_ Drip edge _
tet.
Nails located Nei Imtod
2'�'from save
horn save
Install first SON-sealing adhesiveSig edAes va
Starter Strip positioned along savewith 66runaved Wall first 51tarter 9*P ve
j positioned along sa
shingle wrth
6"removed , Starter Plus eaves and rakes 1/4"-3/4"
Starter Strip shingle overhangs eaves and rakes h='k" D ��
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 FL10674-1112
Revision 7:04/18/2016
Page 3 of 8
QO
TRINITY ERD
6.2.6 Minimum Nailing–Classic'°&Supreme:
Normal Manssrd or Area pars Normal Mansard or Area pars
Wind Areas High Wind desvanes y Wind Ares High Wind d.svenes y
Area pars vientos normaies Areas vientos fuer,.. Area pairs vientos normaires Areas viaiMoa faaert s
' t" lAl t.. t• z= (8 z- r, (A) t• �t• z•_ IB- 1
t n tz t
i
5"Exposure 5 5/8'Exposure
Exposition Ex posici6n
6.2.7 Minimum Nailing–Berkshire°:
Seafarx strip Sealant strip
La tira de 44ador La Lira de seflador
♦.�--►•e----s • —► • ---------• • •�� • •��• •
r \ RL'i" 9V1" 9L2" AU'; 817" 812" 817" 81k'
a
a
r
Standard Fastening Pattern 6-Nail Fastening Pattern
SNaIaM.trig,
La tea de%;Iador
R ire R yt' R
4'L t7'
t
1" AVMk nwfingomml
Cer fo de who de actaho
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 FL10674-1112
Revision 7:04/18/2016
Page 4 of 8
QOTRINITYIERD
6.2.8 Minimum Nailing—Devonshire":
1^ 7" i 8" i 8" i 8- -i 7" -1 1"
Clam fVarls
5318'exposure
Exposi Wn de 5 3U18 put bkoci6���rtl�
WIfaNNI del sallador Ss,• 6`:
Ten 1"Spots of Asphalt Roof Cement
Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern
6.2.9 Minimum Nailing— Duration*, TruDefinition® Duration, Duration® Premium Cool &TruDefinition� Duration"
Designer Color Collection:
4•NaN Fastening Pattern Mail Fastening Pattern
aueNrae 121 g asp rah Laehaa0 a�u�aq ap ran
Ir
nus To- IVP"s.ur saa-
F1
F F
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Steges Greater Than 21:12
awoaMe a.wNrq r...+an�
a-+a•sae•
rov+•epos
of Mp O aooanp 0 mw
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 FL10674-1112
Revision 7:04/18/2016
Page 5 of 8
QOTRINITYIERD
6.2.1 Minimum Nailing—TruDefinitionn Oakridge®,Oakridge®:
4 Nall Pattern 6 Nall Pattern
Eswma con 4 dams Esquema colt 6 dams
r r
r r
Ir
66!8"Exposure Naas 5 stir Exposure NaLs
Exposidda de 66/0 pdg Clercs Exposiddn de 6 6/0 pdg 6 6/8"Exposum Cleves 6 6Ar Exposuw
Egmsiddn do 6 6/0 pdg Exposiddn de 6 6/0 pdg
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slope*Gr"fxw Then 21:12
eu.nrwa.�.nrwq—.t
�• �r -� I �'�rp�r -
s.�r y.yr•
�r
rov�^ayow
of A"hO Roorq C-4
Mansard or Steep Slope Fastening Pattern
6.2.1 Minimum Nailing—WeatherGuard® HP:
VIE 111111111011111110 aft lNrs11View
P.O.7lrrwr�r Ltii Lir
rim w r�ra i+nYra
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-117
Certificate of Authorization#9503 FL10674-R12
Revision 7:04/18/2016
Page 6 of 8
TRINITY ERD
6.3 Hip&Ridge Shingles:
6.3.1 Installation of Berkshires Hip and Ridge Shingles, High Ridge, WeatherGuard� HP Hip and Ridge Shingles and
ProEdge Hip& Ridge Shingles shall comply with the manufacturer's current published instructions, using four
(4) nails per shingle. Installation of DuraRidge'" Hip & Ridge Shingles shall comply with the manufacturer's
current published instructions, using two (2) nails per shingle. Refer to Owens Corning published
information on wind resistance and installation limitations, including the use of hand-sealing for wind
warranties.
6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R90S.2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berkshire" Hip&Ridge and High Ridge:
Fig.1 Q Fig.2
Pmalrle Md
DireWon p ispVlew SpaVlaw
NYe A . 2. Nails
1' TOP L�rIYMtl T
Place
A
Q I I
I
I I I I I
I I
IIS + �' � • .+�
F
I
1
1
1
I
1
6.3.4 Minimum Nailing—WeatherGuard® HP Hip and Ridge:
Fig.C Hip&Ridge Shingle Fastening
Fig.A Q Q Topvlow
Plow.tlYy wYd
�-Direction A
P
Nails 4 4
\It�3N_ A i i WIY IYIY
p i i T'
7' Z,
I I I I
I I
rcaPosure
V. Eq*Wp
Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 FL10674-1112
Revision 7:04/18/2016
Page 7 of 8
Q0
TRINITY ERD
6.3.5 Minimum Nailing-ProEdge Hip& Ridge Shingles:
Prevailing Standard
Wind Direction Fastening
EetlntK�+P Pattani
12• saient
sten 7'b• 7'h' 8•Eo M
Fa
C~Ev""I
Festsesrs with
be conn[ -12•
6.3.6 Minimum Nailing–DuraRidgeTm Hip& Ridge Shingles:
Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer to Owens Corning
published installation instructions for their minimum requirements.
MvV"Dincian Top VWw
~ d '-' &ATMt vW W
Di Baden del vimm prdaeimn 1 vYa raperlar I-
s_ .1
WIN
t�.. • I I I
SO
I
•I
>:
I
• 12-
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 CIA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC–QUA9625 ;(414)248-6409; karen.buchmann@ul.com
- END OF EVALUATION REPORT-
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7
Certificate of Authorization#9503 F1.10674-1112
Revision 7:04/18/2016
Page 8 of 8