HomeMy WebLinkAboutBuilding Permit Application ALL APPLICABLE INFO MUST BE COMPLETED FOR APPLICATION TO BE ACCEPTED Q►
Date: December 28, 2017 Permit Number: l /1
• RECEIVED
Building Permit Application JAN p 3 2018
Planning and Development Services
Building and Code Regulation Division
ST. Lucie County, Permitting
2300 Virginia Avenue,Fort Pierce FL 34982
Phone: (772)462-1553 Fax: (772)462-1578 Commercial Residential xx
PERMIT APPLICATION FOR: Roof
PROPOSED IMPROVEMENT LOCATION:
Address: 9 Julia, Fort Pierce, FL 34951
Legal Description: Spanish Lakes Country Club-See Attached
Property Tax ID#: 1301-111-0001-000-5 Lot No.
Site Plan Name: Block No.
Project Name: Stephenson
Setbacks Front Back: _Right Side: Left Side:
DETAILED DESCRIPTION OF WORK:
WOO I I e
bA
Remove entire 16sq of existing roof shingles system. Install new GAF Timberline Dimensional Shingle
with new flashing, boots, jacks and pipe vents.
CONSTRUCTION INFORMATION:
Additional work toe er orme under this permit—check a appy:
HVAC 11 Gas Tank []Gas Piping _Shutters Windows/Doors
11 Electric E] Plumbing Sprinklers Generator Roof 4/12 Roof pitch
Total Sq. Ft of Construction: 16sgs Sq. Ft. of First Floor:
Cost of Construction:$ 6,000.00 Utilities:L Sewer Septic Building Height:
OWNER/LESSEE: CONTRACTOR:
Name Jon Stephenson Name: Crystal Anderson
Address: 9 Julia Company: Olneya Restoration Group, LLC.
City: Ft. Pierce State: FL Address: 4253 SW High Meadow Avenue
Zip Code: 34951 Fax: City: Palm City State, FL
Phone No. 772-559-4150 Zip Code: 34990 Fax: 772-925-8417
E-Mail: d.k.cox@fpl.com Phone No. 772-222-5019
Fill in fee simple Title Holder on next page(if different E-Mail: Ilawrence@olneya.Com
from the Owner listed above) State or County License: CCC1330974
If value of construction is$2500 or more,a RECORDED Notice of Commencement is required.
_f
I
SUPPLEMENTAL CONSTRUCTION LIEN LAW INFORMATION:
DESIGNER/ENGINEER: Not Applicable MORTGAGE COMPANY: Not Applicable
Name: Name:
Address: Address:
City: State: City: State:
Zip: Phone Zip: Phone:
FEE SIMPLE TITLE HOLDER: Not Applicable BONDING COMPANY: Not Applicable
Name: Name:
Address: Address:
City: City:
Zip: Phone: Zip: Phone:
OWNER/ CONTRACTOR AFFIDVIT: Application is hereby made to obtain a permit to do the work and installation as indicated.
I certify that no work or installation has commenced prior to the issuance of a permit.
St. Lucie County makes no representation that is granting a permit will authorize the permit holder to build the subject structure
which is in conflict with any applicable Home Owners Association rules, bylaws or and covenants that may restrict or prohibit such
structure. Please consult with your Home Owners Association and review your deed for any restrictions which may apply.
In consideration of the granting of this requested permit, I do hereby agree that I will, in all respects, perform the work
in accordance with the approved plans,the Florida Building Codes and St. Lucie County Amendments.
The following building permit applications are exempt from undergoing a full concurrency review: room additions,
accessory structures, swimming pools,fences,walls,signs,screen rooms and accessory uses to another non-residential use
WARNING TO OWNER: Your failure to Record a Notice of Commencement may result in your paying twice for
improvements to your property. A Notice of Commencement must be recorded and posted on the jobsite
before the first inspection. If you intend to obtain financing, consult with lender or an attorney before
commencing work or recording our Notice of Commencement.
Signature of wner/Lessee/Contractor as Agent for Owner Signature o ontractor/License Holder
STATE OF FLORID STATE OF FLORID
COUNTY OF "Q � COUNTY OF "
�
The forgoing instrument w s acknowledged before me The forgoing instrument was acknowledged before me
thiday of C.Q. 20A1 by this"zX__day of 1k0_U,W 20j1 by
W-ZAQA �L LQ)Cl . 4a r A
Name of person making statement Name of person making statement
Personally Known JJ OR Produced Identification Personally Know�t -4 OR Produced Identification
Type of Identification Type of Identification
Produced Produced
(Signatur f Notary Public-St to 0• F Orlda EGANJEANETTELAWRENCE Signature Notary Public-Sta
Notary Public-State of Florida '>4V A MEGAN JEANETTE LAWRENCE
Commission No (Sea ommissiont1GG097477
^ q ommission N q$&*Public-State of Florida
My Comm.Expires Apr 24,2021 Commission 0 GG 097477
Borded tlrougF National Notary Assn. ""•;iF. .., -' MY Comm,Expires Apr 24,&1
Boded ttragt halliMM NMer Asan.
REVIEWS FRONT ZONING SUPERVISOR PLANS VEGETATION SEA TURTLE MANGROVE
COUNTER REVIEW REVIEW REVIEW REVIEW REVIEW REVIEW
DATE
RECEIVED
DATE
COMPLETED
Rev. 8/2/17
JOSEPH E . SMITH, CLERK OF THE CIRCUIT COURT — SAINT LUCIE COUNTY
FILE # 4384891 OR BOOK 4080 PAGE 1340 , Recorded 12/28/2017 08 : 51 : 34 AM
RECEIVED
JAN 0 3 2018
OF COMMENCEMENT ST. Lucle County, Permitting
Permit No. Property Tax ID No, 1301-111.0001.000.5
State of Florida.Count) of St.Lucie
The Undersigned hereby-,ives notice that improvement will be made to certain real property,and in accordance with
C'hapter 713,Florida Sta l Utes,the following information is provided in this Notice of Commencement.
Legal Description of prollet t-and address if available 9 Julia,Fort Pierce.FL 34951
Spanish Lakes Count-/Club Village-See attached
General description of improvements Re-Roof
Ownerilessee Jon Stephenson
Address 9 J:d;a.For.Plera: FL 34051
Interest in property: Ovrner
Fee Simple Title holder(it other than owner) N/A
Address
Contractor Olneya Re:toration Group,I.I.C. _ Phone# 772"222"5019
Address 4253 SW High Meaux`Avenue,Palm City,FL 34990- ' - Fax# 772-925'6417
Suretv NIA Phone#
:Address - --. „- .Y Fax#
:Amount of Bond N/A
Lender N/A Phonert
Address -^
_- fsla
Persons N ithin the State of Florida designated by Owner upon whom notices or other documents may be served as provided
by Section 713.13(R)7.,F orida Statues:
Name Phone#
Address__._.__ _... _. ......_. Fax#
In addition to himself,o%tier designates of
Phone# Fax tt
to receive a cupy of the Licnur's Notice as provided in Section 713.13(I)(b),Florida Statutes. Expiration date of notice of
commencement is one}'ear from the date of recording unless a different date is specified. WARNING•iO OWNER:
ANY PAl'NWN I S NIADE BY 1111:OWNER AI'1•I:R'f 111' i:xPiRATION OF THE;NOTIC17 OF COMMENCEMENT ARE CONSIDERED INtl'ROPl{R
PA1'.%fI:N'IS L'N01'R(•11.713.1' F S.•AND CAN RFSI11.1'IN YOUR PAYING TWICF.FOR IMPROVEMENTSTo YOt:R?ROPI:RTN'. A NOTICE OF
C"ONINIF.NC ENIENT Nil til•HI:RECORDED AND POSTED ON'rim JOB SITE.BEFORE THE FIRST INSPF:(:TtON. ii'YOU INTEND TO OBTAIN
FINANC'INCi. CONSULT Wrill YOUR HINDER OR AN ari'oRNI:)' HEYORG C'ONIMENC,NG WORK oft XLCOROING YOUR NO'rl(T (W
C ClVtA1 P.NC`4l;N 1'
� ( .(\�t•,ur Owner's ur L�ssee'�Aulhurited Ufiker!nircctur/Pnrtncr/►lunaeerf tilenxturc
,qW
tier
tiittnntnn•'.s'I'itlaOflice -'
State of Florida,County of Martin
Acknowledged before me this :)D ,day of 20 17 by
who is Pers rally known to me or who has produced L. S L. _ as identification.
1 '�•C Megan J Lawrence
Signature l Notary Type or Print Name of Notary (Seal)
Title: Notary Public Commission Number GG097477 % MEGANIEANETTELA%V4ENCt
� ��•.� 'VotaYP;bl,-SleteofF!-rIL4a
C-re som a GG 057477
YC-`"4 ExPlec A:;.-24.2221
..... .'.x.'r-r.^.AJ^Ma:•aMI MxnyArrr.
RECEIVED
JAN 0 3 2018
MIAMI ST, Lucie County, Permitting IAMI-DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DMSION Miami,Florida 33175-2474
T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE OA
a -r - w. 'amidade. ov/econom
GAF a ' r T
1 Campus Drive
Parsipanny,NJ 07054
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control Section
(In Miami Dade County)and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this
product or material tested for quality assurance purposes.If this product or material fails to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein,and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: GAF Leak Barriers and Roof Deck Protection
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo,city,state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,
for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then
it shall be done in its entirety.
INSPECTION:A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA 13-1104.11 and consists of pages 1 through 8.
The submitted documentation was reviewed by Alex Tigera.
�l
NOA No.: 14-0915.02
MIAMMADE COUNTY Expiration Date: 02/21/18
Approval Date: 09/10/15
Page 1 of 8
ROOFING COMPONENT APPROVAL
Category Roofing
Sub-Category: Underlayment
Material: SBS/Polypropylene/Asphalt
PRODUCTS DESCRIPTION:
Test Product
Product Dimensions Specification Description
WeatherWatch® 36"x 50' rolls ASTM D 1970 Granular surfaced modified,fiberglass reinforced,
Mineral Surfaced Leak 36"x 66.7' rolls bituminous sheet material for use as a leak barrier
Barrier underlayment in sloped roof assemblies.
Manufacturing Designed as an ice&rain shield.
Location#2,3
WeatherWatch®XT 36"x 50' rolls ASTM D 1970 Mat surfaced modified,fiberglass reinforced
Mat Surfaced Leak 36"x 66.7' rolls bituminous sheet material for use as a leak barrier
Barrier underlayment in sloped roof assemblies.
Manufacturing Designed as an ice&rain shield.
Location#3
StormGuard®Film 36"x 66.7' rolls ASTM D 1970 Modified, fiberglass reinforced,bituminous sheet
Surfaced Leak Barrier material for use as a high temperature leak barrier
Manufacturing underlayment in sloped roof assemblies.
Location#2 Designed as an ice&rain shield.
LibertyTM SBS Self- 39-;/8'' x 66' rolls ASTM D 1970 Self-adhering SBS roof membrane.
Adhering Base/Ply
Sheet
Manufacturing
Location#2
UnderRooff 2 39-1/8"x 67.8' rolls ASTM D 1970 Self-adhering reinforced membrane of SBS
Polyester-Surfaced modified asphalt with polyester surfacing for use
Leak Barrier with asphalt shingle roof assemblies. Roof slopes
Manufacturing of 2:12— 12:12 are acceptable as indicated by
Location#1,3 local codes and manufacturer's installation
instructions.
UnderRoof"HT High 39_3/8,,x 61.0' rolls ASTM D 1970 Self-adhering reinforced membrane of SBS
Temperature Leak modified asphalt with polyester surfacing for use
Barrier as a high temperature underlayment in sloped
Manufacturing metal and asphalt shingle roof assemblies. Roof
Location#3 slopes of 2:12—12:12 are acceptable as indicated
by local codes and manufacturer's installation
instructions.
NOA No.: 14-0915.02
CMIAM&DALDE COUNTY Expiration Date: 02/21/18
Approval Date: 09/10/15
Page 2 of 8
PRODUCTS DESCRIPTION:
Test Product
Product Dimensions Specification Description
Deck-Armor" 54"x 222' rolls ASTM D 226 A UV-stabilized polypropylene breathable
Premium Breathable 48"x 100' rolls Type II underlayment. To be used for roof deck
Roof Deck Protection protection as an underlayment in sloped roof
Manufacturing assemblies.
Location#4
Tiger PawTM Roof Deck 48"x 250' rolls ASTM D 226 A UV-stabilized polypropylene non-breathable
Protection 48"x 100' rolls Type II underlayment.To be used for roof deck protection
Manufacturing as an underlayment in sloped roof assemblies.
Location#5,8,9
FeltBustee High- 48"x 250' rolls ASTM D 226 A UV-stabilized polypropylene non-breathable
Traction Synthetic Type I underlayment.To be used for roof deck protection
Roofing Felt as an underlayment in sloped roof assemblies.
Manufacturing
Location#10
Shingle-Mate®Roof 36"x 144' rolls ASTM D 226 Fibergass-reinforced asphalt felt underlayment. To
Deck Protection Type I be used for roof deck protection as an
Manufacturing underlayment in sloped roof assemblies.
Location#6,7
NOA No.: 14-0915.02
CMIAMDA E COUNTY Expiration Date: 02/21/18
Approval Date: 09/10/15
Page 3 of 8
MANUFACTURING LOCATION:
1. Fresno,CA
2. Mt.Vernon,IN
3. North Branch,NJ
4. North Bay,Ontario
5. Mission,British Columbia
6. Pryor,OK
7. McGregor,TX
8. Qingdao,China
9. Charleston, SC
10. Spartanburg, SC
EVIDENCE SUBMITTED:
Test Agency Test Identifier Test Name/Report Date
Intertek Testing Services NA Ltd. 3077464-01 ASTM D 1970 08/23/06
3090131 Wind Uplift and Self Sealability 08/23/06
100258583COQ-OIOA ASTM D 226 Type II 01/11/11
100673818COQ-003 ASTM D 226 Type II 06/13/13
10157289000Q-005 ASTM D 226 Type II 04/17/14
PRI Construction Materials RGM-023-02-01 ASTM D 4798 05/16/07
Technologies,LLC. GAF-112-02-01 ASTM D 226 Type II 03/15/06
GAF-238-02-01 ASTM D 1970 03/03/10
GAF-323-02-01 ASTM D 1970 11/30/11
GAF-324-02-01 ASTM D 1970 11/30/11
GAF-325-02-01 ASTM D 1970 11/30/11
GAF-326-02-01 ASTM D 1970 11/30/11
GAF-275-02-01 ASTM D 1970 11/11/10
GAF-344-02-01 ASTM D 1970 04/23/12
GAF-339-02-01 ASTM D 226 Type I 03/14/12
ELK-311-02-01 ASTM D 1970 09/11/07
GAF-446-02-01 ASTM D 226 Type 1 09/26/13
GAF-518-02-01 ASTM D 226 Type I 06/04/14
NOA No.: 14-0915.02
CMIAMI-DADECOUNTY Expiration Date: 02/21/18
Approval Date: 09/10/15
Page 4 of 8
APPROVED ASSEMBLIES:
Deck Type 1: Wood,non-insulated
Deck Description: 19/32° or greater plywood or wood plank
System E(1): Anchor sheet mechanically fastened to deck,membrane adhered.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle-Mate®Roof Deck Protection OR one or more plies
of ASTM D 226 Type II,Deck-Armorl Premium Breathable Roof Deck Protection,FeltBuster®
High-Traction Synthetic Roofing Felt,or Tiger Pawl Roof Deck Protection with a minimum 4"
side lap and a 6"end lap mechanically fastened to the deck with approved nails and tin caps 6"
o.c.at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow,tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape(follow the tape's manufacturer's
installation instructions).Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fastneners.
Membrane: One or more plies of WeatherWatch®Mineral Surfaced Leak Barrier,WeatherWatch®XT Mat
Surfaced Leak Barrier, StormGuard®Film Surfaced Leak Barrier,or LibertyTM SBS Self-
Adhering Base/Ply Sheet membrane with a minimum 3"side lap and 6"end lap. Place the first
course of membrane parallel to the eave,rolling the membrane to obtain maximum contact.
Remove the release membrane as the membrane is applied. Vertical strapping of the roof with
WeatherWatch®Mineral Surfaced Leak Barrier,WeatherWatch®XT Mat Surfaced Leak Barrier,
or StormGuard®Film Surfaced Leak Barrier is acceptable.
Surfacing: Approved Roofing Assembly.
Deck Type 1: Wood,non-insulated
Deck Description: 19/32" or greater plywood or wood plank
System E(2): Membrane mechanically fastened to deck.
Separator Sheet: One or more plies of GAF GAFGLAS®Ply 4,GAFGLAS®Flex-PlyTM 6,Rosin Paper,ASTM D
226 Type I or Type II, Shingle-Mate®Roof Deck Protection,Deck-Armoil Premium
Breathable Roof Deck Protection,FeltBuster®High-Traction Synthetic Roofing Felt,or Tiger
PawTM Roof Deck Protection loose laid.
Membrane: One or more plies of WeatherWatch®Mineral Surfaced Leak Barrier,WeatherWatch®XT Mat
Surfaced Leak Barrier, StormGuard®Film Surfaced Leak Barrier,or LibertyTM SBS Self-
Adhering Base/Ply Sheet membrane mechanically fastened with a minimum 3"side lap and a 6"
end lap to deck through the separator sheet with approved nails and tin caps 6" o.c.at the laps
and two staggered rows 12" o.c. in the field of the roll.
Surfacing: Approved Roofing Assembly.
NOA No.: 14-0915.02
MIAMMADE COUNTY Expiration Date: 02/21/18
Approval Date: 09/10/15
Page 5 of 8
Deck Type 1: Wood,non-insulated
Deck Description: 19/32" or greater plywood or wood plank
System E(3): Anchor sheet mechanically fastened to deck,membrane adhered.
Secondary Water Install a minimum 4"wide WeatherWatch®Mineral Surfaced Leak Barrier, WeatherWatch®XT
Barrier: Mat Surfaced Leak Barrier,or StormGuard®Film Surfaced Leak Barrier membrane over the
(Optional) joints of the plywood roof deck prior to installation of the base sheet.Do not overlap end or side
joints.All side and end laps should be butted firmly side by side,flush with each other but not
overlapped.Do not leave the WeatherWatch®Mineral Surfaced Leak Barrier,WeatherWatch®
XT Mat Surfaced Leak Barrier,or StormGuard®Film Surfaced Leak Barrier membrane exposed
for more than 30 days without a roof deck protection underlayment protecting the secondary
water barrier.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle-Mate®Roof Deck Protection OR one or more plies
of ASTM D 226 Type II,Deck-Armor'Premium Breathable Roof Deck Protection,
FeltBuster®High-Traction Synthetic Roofing Felt,or Tiger Pawl Roof Deck Protection with a
minimum 4"side lap and a 6"end lap mechanically fastened to the deck with approved nails and
tin caps 6" o.c.at the laps and four staggered rows 12"o.c. in the field of the roll.
If roof is exposed to rain/snow,tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape(follow the tape manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fasteners.
Surfacing: Approved Roofing Assembly.
Deck Type 1: Wood,non-insulated
Deck Description: 19732"or greater plywood or wood plank
System E(4): Anchor sheet mechanically fastened to deck,membrane adhered.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle-Mate®Roof Deck Protection OR one or more plies
of ASTM D 226 Type 1I,Deck-Armor'Premium Breathable Roof Deck Protection,
FeltBuster®High-Traction Synthetic Roofing Felt, or Tiger PawTM Roof Deck Protection with a
minimum 4"side lap and a 6"end lap mechanically fastened to the deck with approved nails and
tin caps 6" o.c.at the laps and four staggered rows 12" o.c.in the field of the roll.
If roof is exposed to rain/snow,tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape(follow the tape's manufacturer's
installation instructions).Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fastneners.
Membrane: One or more plies of StormGuard®Film Surfaced Leak Barrier,UnderRoofl 2 Polyester-
Surfaced Leak Barrier or UnderRooflT'HT High Temperature Leak Barrier membrane with a
minimum 4"side lap and 6"end lap. Place the first course of membrane parallel to the eave,
rolling the membrane to obtain maximum contact. Remove the release membrane as the
membrane is applied.
Surfacing: Approved for Metal roofing(StormGuard®Film Surfaced Leak Barrier,or UnderRoofrm HT
High Temperature Leak Barrier),Slate,and Asphalt Shingle assemblies.
NOA No.: 14-0915.02
MIAMFDADE COUNTY Expiration Date: 02/21/18
Approval Date: 09/10/15
Page 6 of 8
LIMITATIONS:
1. Fire classification is not part of this acceptance.
2. WeatherWatch® Mineral Surfaced Leak Barrier, WeatherWatch® XT Mat Surfaced Leak Barrier, StormGuard®
Film Surfaced Leak Barrier, LibertyTM SBS Self-Adhering Base/ply Sheet, UnderRoofl HT High Temperature
Leak Barrier, Shingle-Mate® Roof Deck Protection, Deck-ArmorTM Premium Breathable Roof Deck Protection,
FeltBuster®High-Traction Synthetic Roofing Felt, and Tiger Pawl Roof Deck Protection shall not be used as roof
tile underlayment.
3. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code. WeatherWatch®Mineral Surfaced Leak Barrier, WeatherWatch®XT Mat Surfaced Leak
Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self-Adhering Base/Ply Sheet, UnderRoof'm 2
Polyester-Surfaced Leak Barrier, UnderRoof m HT High Temperature Leak Barrier, Shingle-Mate® Roof Deck
Protection, Deck-Armor' Premium Breathable Roof Deck Protection, FeltBuster® High-Traction Synthetic
Roofing Felt, and Tiger Pawl Roof Deck Protection shall be installed in strict compliance with applicable
Building Code.
4. WeatherWatch® Mineral Surfaced Leak Barrier, WeatherWatch®XT Mat Surfaced Leak Barrier, StormGuard®
Film Surfaced Leak Barrier, LibertyTM SBS Self-Adhering Base/Ply Sheet, UnderRoof1m 2 Polyester-Surfaced
Leak Barrier, UnderRoofrm HT High Temperature Leak Barrier, Shingle-Mate® Roof Deck Protection, Deck-
ArmorTM Premium Breathable Roof Deck Protection,FeltBuster®High-Traction Synthetic Roofing Felt, and Tiger
Pawl Roof Deck Protection membranes shall be applied to a smooth, clean and dry surface with deck free of
irregularities.
5. WeatherWatch® Mineral Surfaced Leak Barrier, WeatherWatch® XT Mat Surfaced Leak Barrier, StormGuard®
Film Surfaced Leak Barrier, LibertyTM SBS Self-Adhering Base/Ply Sheet, UnderRooflM 2 Polyester-Surfaced
Leak Barrier, UnderRoofl HT High Temperature Leak Barrier, Shingle-Mate® Roof Deck Protection, Deck-
ArmorTM Premium Breathable Roof Deck Protection,FeltBuster®High-Traction Synthetic Roofing Felt, and Tiger
PawTM Roof Deck Protection membranes shall not be applied over an existing roof membrane.
6. WeatherWatch® Mineral Surfaced Leak Barrier, WeatherWatch® XT Mat Surfaced Leak Barrier, StormGuard®
Film Surfaced Leak Barrier, LibertyTM SBS Self-Adhering Base/Ply Sheet, UnderRoof'M 2 Polyester-Surfaced
Leak Barrier, UnderRoofrM HT High Temperature Leak Barrier, Shingle-Mate® Roof Deck Protection, Deck-
Armor'Premium Breathable Roof Deck Protection, FeltBuster®High-Traction Synthetic Roofing Felt, and Tiger
PawTM Roof Deck Protection shall not be left exposed as a temporary roof for longer than 30 days of application.
7. WeatherWatch® Mineral Surfaced Leak Barrier, WeatherWatch®XT Mat Surfaced Leak Barrier, StormGuard®
Film Surfaced Leak Barrier, LibertyTM SBS Self-Adhering Base/Ply Sheet, UnderRoof m 2 Polyester-Surfaced
Leak Barrier, UnderRoofl HT High Temperature Leak Barrier, Shingle-Mate® Roof Deck Protection, Deck-
ArmorTM Premium Breathable Roof Deck Protection, FeltBuster®High-Traction Synthetic Roofing Felt, and Tiger
PawTM Roof Deck Protection may be used with any approved roof covering Notice of Acceptance listing
WeatherWatch® Mineral Surfaced Leak Barrier, WeatherWatch® XT Mat Surfaced Leak Barrier, StormGuard®
Film Surfaced Leak Barrier, LibertyTM SBS Self-Adhering Base/Ply Sheet, UnderRoof`M 2 Polyester-Surfaced
Leak Barrier, UnderRoof m HT High Temperature Leak Barrier, Shingle-Mate® Roof Deck Protection, Deck-
ArmorTM Premium Breathable Roof Deck Protection, FeltBuster®High-Traction Synthetic Roofing Felt, and Tiger
Paw'Roof Deck Protection as a component part of an assembly in the Notice of Acceptance. If WeatherWatch®
Mineral Surfaced Leak Barrier, WeatherWatch®XT Mat Surfaced Leak Barrier, StormGuard®Film Surfaced Leak
Barrier, LibertyTM SBS Self-Adhering Base/Ply Sheet, UnderRoof' 2 Polyester-Surfaced Leak Barrier,
UnderRoofl HT High Temperature Leak Barrier, Shingle-Mate®Roof Deck Protection, Deck-Armor' Premium
Breathable Roof Deck Protection, FeltBuster® High-Traction Synthetic Roofing Felt and Tiger Paw' Roof Deck
Protection are not listed; a request may be made to the Authority Having Jurisdiction (AHJ) or the Miami-Dade
County Product Control Department for approval provided that appropriate documentation is provided to detail
NOA No.: 14-0915.02
MwruaaDe 0�rjumaxi , NTY Expiration Date: 02/21/18
Approval Date: 09/10/15
Page 7 of 8
LIMITATIONS:
compatibility of the products,wind uplift resistance,and fire testing results.
8. All nails in the deck shall be carefully checked for protruding heads. Re-fasten any loose decking panels. Sweep
the deck thoroughly to remove any dust and debris prior to application. Install when temperatures are 45° F and
rising.
9. When applying the membrane in the valley, start at the low point and work to the high point,rolling the membrane
from the center outward in both directions.
10. Roll or broom the entire membrane surface so as to have 100%contact with the surface,giving special attention to
overlap areas.
11. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance and applicable Building Code.
12. Wherever the adhesive back of UnderRoofl 2 Polyester-Surfaced Leak Barrier, or UnderRoofl HT High
Temperature Leak Barrier comes in contact with polyester surfacing such as end laps, penetrations, and flashing
material,it must be set in a 1/8"troweling of an approved ASTM D 4586 Type I roofing cement.
13. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
14. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo,city
and state of manufacturing facility, and the following statement: "Miami-Dade County Product Control Approved"
or the Miami-Dade County Product Control Seal as shown below.
CMLAMFDADE COUNTY
, ...• X
END OF THIS ACCEPTANCE
NOA No.: 14-0915.02
APPROVED! Expiration Date: 02/21/18
Approval Date: 09/10/15
Page 8 of 8
RECEIVED
EXTERIOR RESEARCH&DESIGN, LLC.
JAN 0 3 2018 Certificate of Authorization#9503
TRINI 1 1 353 CHRISTIAN STREET, UNIT#13
ERD ST, Lucie County, Permitting OXFORD,CT 06478
�. # (203)262-9245
EVALUATION REPORT
GAF Evaluation Report 01506.02.06-1112
1 Campus Drive FL6267-1112
Parsippany, NJ 07054 Date of Issuance:02/28/2006
(800)766-3411 Revision 12:02/14/2017
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code
sections referenced herein.
DESCRIPTION: GAF Roof Ventilation Products
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s)changes,the referenced
Quality Assurance documentation changes,or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product
changes or the referenced Quality Assurance documentation changes. Trinity)ERD requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 10.
Prepared by:
+UP• E X •;moi.
Robert J.M.Nieminen P.E. %� p ? ,� The hcslmileseat appearing was authorized byRobert Nieminen,
t ��^TF'•. ^e.��.•r`� ••• P.E.on 02/14/2017.This does not serve as an electronically signed
�, /Qy 4l document.Signed,sealed hardcoples have been transmitted to the
Florida Registration No.59166,Florida DCA ANE1983
��r`•"ir�•`s Product Approval Administrator and to the named client
CERTIFICATION OF INDEPENDENCE:
1. Trinityl ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinityl ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E.does not have, nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither TrinitylERD nor Robert Nieminen, P.E. are, in any way,the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
TRINITY ERD
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Roofing Accessories that are an Integral Part of the Roofing System
Compliance Statement: GAF Roof Ventilation Products, as produced by GAF, have demonstrated compliance with
the following sections of the 51h Edition (2014) Florida Building Code through testing in accordance with the
following Standards. Compliance is subject to the Installation Requirements and Limitations/ Conditions of Use set
forth herein.
2. STANDARDS:
Section Property Standard Year
1504.3 Wind ASTM E330 2002
1506.5/1517.5.1 Corrosion Resistance(of nails) TAS 114,Appendix E 1995
1523.6.5.2.13 Wind Driven Rain TAS 100(A) 1995
1523.6.5.2.13.1 Physical Properties TAS 110 2000
2614.2 Weatherometer ASTM G155 2005
3. REFERENCES:
Entity Examination Reference Date
ATI(TST 1558) Physical Properties 01-49035.01 03/02/2004
ATI(TST 1558) Wind Driven Rain 01-44964.01 01/15/2004
ATI(TST 1558) Wind Driven Rain 60172.01-122-18 10/07/2005
ATI(TST 1558) Physical Properties 59665.02-106-31 09/16/2005
ATI(TST 1558) Wind Driven Rain 84608.01-106-18 11/12/2008
ATI(TST 1558) Wind Driven Rain A5250.01-109-18 02/18/2011
ATI(TST 1558) Wind Uplift 87074.01-109-44 12/03/2008
ATI(TST 1558) Wind Uplift C2396.01-109-44 11/05/2012
ATI(TST 1558) Wind Uplift D1957.01-109-44 03/04/2014
ATI(TST 1558) Wind Uplift E0818.01-109-44 09/23/2014
ATI(TST 1558) Physical Properties D2702.01-106-18 06/30/2014
ATI(TST 1558) Wind Uplift E6744.01-109-44 04/30/2015
ATI(TST 1558) Wind Driven Rain G2331.01-109-44 01/10/2017
PRI(TST 5878) Weatherometer HBP-007-02-01 06/24/2004
PRI(TST 5878) Physical Properties HBP-002-02-01 06/06/2001
PRI(TST 5878) Wind Driven Rain HBP-01-02-01 11/02/2000
PRI(TST 5878) Wind Driven Rain BRY-021-02-01 12/31/2003
PRI(TST 5878) Physical Properties BRY-025-02-01 09/17/2004
PRI(TST 5878) Physical Properties GAF-138-02-06 02/09/2007
PRI(TST 5878) Wind Driven Rain GAF-138-02-04 02/09/2007
PRI(TST 5878) Wind Driven Rain GAF-310-02-01 07/07/2011
ETC Labs(TST 2411) Physical Properties ETC-01-718-10379.0 01/16/2000
ETC Labs(TST 2411) Physical Properties ETC-03-718-14602.0 01/20/2004
ETC Labs(TST 2411) Physical Properties ETC-07-718-19959.0 09/27/2007
Miami-Dade(CER 1592) Various Various NOAs Current
Miami-Dade(CER 1592) Corrosion Resistance(of nails) Certification L 12-0614.08 06/26/2012
Miami-Dade(CER 1592) Corrosion Resistance(of nails) Certification L 12-0601.24 06/29/2012
Miami-Dade(CER 1592) Corrosion Resistance(of nails) Certification L 15-0421.09 05/07/2015
UL,LLC.(QUA 9625) Quality Control Inspection Report,R15072,GA1 03/23/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R15072,GA2 04/15/2016
Exterior Research and Design,I.I.C. Evaluation Report 01506.02.06-1112
Certificate of Authorisation x9503 FBC NON-HVHZ EVALUATION FL6267-R12
GAF Revision 12:02/14/2017
Page 2 of 10
QO
TRINITY ERD
4. PRODUCT DESCRIPTION:
4.1 Cobra® Exhaust Vent is a low-profile attic ridge vent of mesh-construction for use in shingle roof systems.
The product measures 10%2-inch wide supplied in 20 and 50 ft long rolls, and is supplied with corrosion
resistant 1%-inch coil nails(nail gun version) or 2%2-inch Smart Nails" (hand nail version). Cobra® Exhaust
Vent has a published net free ventilation area (NFVA) of 14.1 in /lineal foot for nail gun version and 16.9
int/lineal foot for hand nail version.
4.2 Cobra® Rigid Vent 3'" is a plastic, low-profile attic ridge vent for use in shingle roof systems with 12-inch
width ridge caps. The product measures 13-13/16-inch wide supplied in 48-inch long sections, and is
supplied with 3-inch corrosion resistant ring shank nails. Cobra® Rigid Vent 3'" has a published net free
ventilation area(NFVA)of 18 in /lineal foot.
4.3 Cobra® Rigid Vent 3' -9" is a plastic, low-profile attic ridge vent for use in shingle roof systems with 10-
inch width ridge caps. The product measures 11%2-inch wide supplied in 48-inch long sections, and is
supplied with 3-inch corrosion resistant ring shank nails. Cobra® Rigid Vent 3' - 9" has a published net
free ventilation area(NFVA)of 18 in /lineal foot.
4.4 Cobra® Snow CountryTM' is a plastic, low-profile attic ridge vent with filter for use in shingle roof systems.
The product measures 13-13/16-inch wide supplied in 48-inch long sections. Cobra*Snow Country' has a
published net free ventilation area(NFVA)of 18 inZ/lineal foot.
4.5 Cobra®Snow Country AdvancedTM' is a plastic, low-profile attic ridge vent with filter for use in shingle roof
systems with 12-inch width ridge caps. The product measures 13-13/16-inch wide supplied in 48-inch long
sections, and is supplied with 3-inch corrosion resistant ring shank nails. Cobra® Snow Country
Advanced'" has a published net free ventilation area(NFVA)of 18 in'/lineal foot.
4.6 Cobra®Snow Country Advanced'"' -9" is a plastic, low-profile attic ridge vent with filter for use in shingle
roof systems with 10-inch width ridge caps. The product measures 11%2-inch wide supplied in 48-inch long
sections, and is supplied with 3-inch corrosion resistant ring shank nails. Cobra® Snow Country
Advanced""-9"has a published net free ventilation area(NFVA)of 18 in'/lineal foot.
4.7 Cobra* Ridge Runner' is a polypropylene plastic, low-profile attic ridge vent for use in shingle roof
systems. The product measures 11%2-inch wide supplied in 20 ft long rolls, and is supplied with corrosion
resistant 1%-inch coil nails. Cobra®Ridge Runner®has a published net free ventilation area(NFVA)of 12.5
in /lineal foot.
4.8 TruSlate® Ridge Vent is a plastic, low-profile attic ridge vent for use in TruSlate® roof systems. The
product measures 11.4-inch wide supplied in 48-inch long sections. TruSlate® Ridge Vent has a published
net free ventilation area(NFVA)of 20 in'/lineal foot.
4.9 Cobra® Hip Vent is a plastic, low-profile attic hip vent with filter for use in shingle roof systems. The
product, only for use on hips, measures nominal 11.4-inch wide supplied in 48-inch long sections, and is
supplied with corrosion resistant 1%-inch coil nails. Cobra® Hip Vent has a published net free ventilation
area(NFVA)of 9 inZ/lineal foot.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither Trinityl ERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
Exterior Research and Design,I.I.C. Evaluation Report 01506.02.06-1112
certificate of Authorization#9503 FBC NON-HVHZ EVALUATION FL6267-R12
GAF Revision 12:02/14/2017
Page 3 of 10
TRINITY ERD
5.3 Minimum Roof Slopes:
Product Minimum Slope
Cobra®Exhaust Vent 2:12
Cobra®Rigid Vent 3'" 3:12
Cobra® Rigid Vent 31-9" 3:12
Cobra®Snow Country'" 3:12
Cobra®Snow Country Advanced'" 3:12
Cobra®Snow Country Advanced" -9" 3:12
Cobra*Ridge Runner,* 3:12
TruSlate®Ridge Vent 5:12
Cobra®Hip Vent Min.3:12 to max. 12:12
5.4 Unless otherwise determined through use of performance levels in Section 5.5, the maximum mean roof
height for Cobra® Exhaust Vent, Cobra® Rigid Vent 3, Cobra® Rigid Vent 3—9", Cobra®Snow Countr",
Cobra® Snow Country Advanced'", Cobra® Snow Country Advanced" — 9", Cobra® Ridge Runner®,
TruSlate®Ridge Vent and Cobra®Hip Vent shall be 33 ft.
5.5 Maximum Allowable Design Pressures: The following performance levels may be utilized for projects
where the maximum mean roof height exceeds 33 ft. The Allowable Design Pressure shall meet or exceed
critical design pressure determined by a qualified design professional in accordance with FBC Chapter 16.
No rational analysis is permitted.
Allowable Design
Substrate: Product Pressure(psf)
Min.7/16-inch plywood Cobra®Exhaust Vent(nail gun version) -150
Min.7/16-inch plywood Cobra®Exhaust Vent(hand nail version) -180
Min.7/16-inch plywood Cobra®Rigid Vent 3", Rigid Vent 31"-9",Snow -215
Country'",Snow Country Advanced'" and Snow
Country Advanced'"-9"
Min. 7/16-inch OSB or Cobra*Ridge Runner® -180
plywood
Min.7/16-inch plywood TruSlate®Ridge Vent -190
Min.7/16-inch plywood Cobra® Hip Vent -205
5.5.1 Allowable Design Pressure is the result of testing for wind load resistance based on allowable wind loads,
and reflects the ultimate passing pressure divided by 2(the 2 to 1 margin of safety per FBC 1504.9 has
already been applied). Refer to FBC 1609 for determination of design wind loads.
5.6 Installation shall result in minimum net free ventilation area requirements set forth in FBC Sections
1203.2. When more than one level of roof ridge existing over a single attic space, use ridge vents only at
the high ridge.
Exterior Research and Design,I.I.C. Evaluation Report 01506.02.06-R12
Certificate of Authorization#9503 FBC NON-HVHZ EVALUATION FL6267-R12
GAF Revision 12:02/14/2017
Page 4 of 10
QO
TRINITY ERS
6. INSTALLATION:
6.1 GAF Roof Ventilation Products shall be installed in accordance with GAF published installation
requirements subject to the Limitations set forth in Section 5 herein and the specifics noted below.
6.2 COBRA®EXHAUST VENT:
6.2.1 Chalk a cut-line 1-inch off each side of the ridge and cut a slot along the apex of the roof measuring 2-inch
(for truss construction) or 3%-inch (for ridge pole construction). The slot should terminate 6-inches from
each end and 12-inches from hip intersections or chimneys. Cut only the sheathing; do not cut trusses.
Figure A.
6.2.2 Unroll the vent along the entire length of the ridge, covering uncut 6-inch sheathing area on both ends.
Shorter lengths can be joined by caulking and butting the ends. Figure B.
6.2.3 Apply a bead of polyurethane roof sealant to the underside of the entire perimeter of the vent and nail
with min. 2%:-inch galvanized roofing nails at each corner and 10-inch o.c. Do not use excessive roof
cement,as it may result in shingle blistering.
6.2.4 Apply a bead of polyurethane roof sealant in the shape of a"C"to the underside of the entire perimeter of
the cap shingles, and install cap shingles directly over the vent using Smart Nails`" or 1%-inch corrosion
resistant coil nails(supplied with the vent). Figure C. Do not use excessive roof cement, as it may result in
shingle blistering.
6.2.5 Cobra® Exhaust Vent (hand nail version) and Cobra® Exhaust Vent (nail gun version) have a %-inch or
5/8-inch nominal thickness, respectively, to facilitate ventilation. Care shall be taken not to crush or
compact the product during installation. Figure D.
1 1
3�+ S.
Hand-Nail Version Nail Gun Version
Exterior Research and Design,LLC. Evaluation Report 01506.02.06-1112
Certificate of Authorization 119503 FBC NON-HVHZ EVALUATION F1.6267-1112
GAF Revision 12:02/14/2017
Page 5 of 10
TRINITY ERD
6.3 COBRA® RIGID VENT 3^", RIGID VENT 3`" -9",SNOW COUNTRY*"',SNOW COUNTRY ADVANCED'"'AND SNOW COUNTRY
ADVANCED'"A-9":
6.3.1 Mark-off and cut the slot opening as follows, ensuring that the ends of the opening stop at least 6-inch
from any end walls and at least 12-inch from hip and ridge intersections or chimneys.
➢ No Ridge Board:Cut a 7/8-inch opening on each side of the ridge(Figure A).
➢ With Ridge Board: Cut a 1-5/8-inch opening on each side of the ridge(Figure B).
V4"
I I
3'/a
No Ridge Board With Ridge Board
6.3.2 Sealant: Apply a bead of silicone caulking or roof cement to the underside of the outer baffle along both
edges and at exposed ends,ensuring the outside edges where the vent meets the shingles are sealed with
the caulk or flashing cement.
6.3.3 Vent Placement: Starting at one end of the slot, place,center and conform the Cobra® rigid vent over the
slot with the vent firmly against the roof surface,ensuring the vent extends past the slot opening by at
least 6-inch.
6.3.4 Fasteners: For Cobra®Rigid Vent 3'",Cobra®Rigid Vent 3' -9",Cobra®Snow Country Advanced'and
Cobra®Snow Country Advanced'"-9"only,use the 3-inch corrosion resistant ring shank nails(included).
For Cobra®Snow Country",use corrosion resistant nails at least 3-inch or longer. Nails must always
penetrate through plywood decks or at least%-inch into wood planks. NOTE:GAF recommends 3-inch
corrosion resistant ring shank nails for increased uplift resistance.
6.3.5 Spacing: Attach the vent section through the pre-molded nailing holes located at 3, 12, 24,36 and 45-inch
from the start of each 48-inch vent piece.
6.3.6 Joints: Apply the subsequent Cobra® rigid vent sections over the length of the ridge using the
overlap/underlap tabs.
6.3.7 Ridge Shingles: Install ridge shingles in accordance with shingle manufacturer's published installation
instructions, using corrosion resistant nails detailed in 6.3.4. A nail line is inscribed on top of the Cobra®
rigid vent to serve as a guide.
Exterior Research and Design,I.I.C. Evaluation Report 01506.02.06-1112
Certificate ofAuthori:ation#9503 FBC NON-HVHZ EVALUATION FL6267-1112
GAF Revision 12:02/14/2017
Page 6 of 10
TRINITY ERD
6.4 COBRA®RIDGE RUNNER®
6.4.1 Cut slot per 6.3.1.
6.4.2 Tear a 1-foot section to be used as a template for laying the vent out(Figure E-G)and center the template/
locator over the ridge cap shingles at the beginning of the vent slot. Note the location of the baffle(Figure
H). Make sure to do this at both ends of the installation.
� r �
� t
o
6.4.3 Measure the distance from the edge of the roof slot to the exterior baffle(D). Establish a chalk line along
one side of the ridge (Figure 1). Unroll the vent and use the included 1-3/4-inch pneumatic corrosion
resistant roofing nails to attach the first side of the ridge vent with the exterior of the baffle aligned with
the chalk line (Figure J). Proceed with using the V interval EasyTearTM system to custom size the vent to
the appropriate length. If the EasyTearT1 system can not be utilized, use a utility knife to size the vent. Nail
gun targets are embossed on the part as a guide for property attaching vent to the roof.The vent should
be fastened on 6-inch centers(Figure K).
D
elf"line
0
Exterior Research and Design,I.I.C. Evaluation Report 01506.02.06-1112
Certificate of Authorization#9503 FBC NON-HVHZ EVALUATION FL6267-R12
GAF Revision 12:02/14/2017
Page 7 of 10
TRINITY ERD
6.4.4 NOTE: When fastening the vent and cap shingles, be sure that the included 1 3/4-inch corrosion resistant
coil nails completely penetrate plywood or provide at least 3/4-inch penetration into wood planks. In the
case they do not, you must use alternate corrosion resistant nails that provide the required penetration.
Proceed with attaching the other side of the vent. When beginning to nail down the second side, do NOT
begin at the end; begin between the first and second one-foot sections and then return to fasten the first
one-foot section.This will allow for proper fit.
6.4.5 Install ridge shingles in accordance with shingle manufacturer's published installation instructions, using
the nail-lines on top of the ridge vent for proper lapping.
6.5 TRUSLATE®RIDGE VENT:
6.5.1 DO NOT use on hips.
6.5.2 Intall TruSlate®Ridge Vent before installing the field slates.
6.5.3 After determining the total length of TruSlate®Ridge Vent required(for proper ventilation),determine the
necessary slot opening. Mark-off and cut the slot opening, ensuring the ends of the opening stop at least
6-inch from any end walls and at least 12-inch from hip and ridge intersections or chimneys.
Roofs without a ridge board:Cut a 7/8-inch opening along the ridge on each side(Figure A).
Roofs with a ridge board: Cut a 1-5/8-inch opening along the ridge on each side(Figure B).
Fig. A Fig. B
(41 mml t%' 11 a,"xN
(22 mm)7/8- 7/8'(22 mm) L/
3Yi lex mm)
With Ridge Board
1V4"(44 mm)
No Ridge Board
6.5.4 Install an 18-inch wide section of ASTM D1970 self-adhering leak barrier (holding Florida Statewide
Product Approval or Approved on a Local Basis) from the edge of the ridge slot extending down towards
the roof deck on both side of the slot.
6.5.5 Place the TruSlate® Ridge Vent over the ridge slot, "peaked" and centered over the ridge slot, and attach
using minimum 3-inch long corrosion resistant ring-shank nails through the pre-molded nail holes on the
vent, located 3-inch from the ends and 9-inch o.c. Fasteners shall penetrate through plywood decks or
embed minimum%-inch into wood plank decks.
6.5.6 Continue over the length of the ridge, utilizing the male/female connectors to connect units. Ensure the
finished ends include the pre-molded end caps. Cover all exposed nail heads on the vent with silicone
caulk. Intall a bead of exterior grade silicone sealant at the downslope leading edges of the ridge vent, at
the junction of the leading edge and the leak-barrier below.
6.5.7 Install the top course of TruSlate® field slates, UnderBlockTM UV & Moisture Barrier and TruSlate® trim
slates in accordance with GAF published installation instructions. Intall TruSlate®trim slates with 10-inch
exposure using minimum 1-5/8-inch long deck screws through pre-drilled holes,through the ridge vent to
engage the wood deck.
Exterior Research and Design,I.I.C. Evaluation Report 01506.02.06-R12
Certificate of Authorization#9503 FBC NON-HVH2 EVALUATION F1.6267-1112
GAF Revision 12:02/14/2017
Page 8 of 10
TRINITY ERS
Roof Osdc Protection
18' J 10'
257 mm
weather wa l"or
Stam(3 MM Leah Barrier
6.6 COBRA®HIP VENT
6.6.1 The roof deck shall consist of minimum of 7/16 inch thick plywood or OSB wood structural panels. Use
only on roofs with slopes between 3:12 and 12:12. Install only on hips. Do not install Cobra® Hip Vent on
ridges.
6.6.2 Sequencing: If ridge ventilation will be installed, always install the ridge vent to the end of the ridge
before installing Cobra®Hip Vent.
6.6.3 Hip Air Slot: Determine the number of Cobra Hip Vent sections needed for proper ventilation and the
location for cuts in the roof hip. Cobra*Hip Vent is installed over a 2%inch wide slot opening centered on
the hip beginning at 12 inches below the top of the hip and extending 36 inches down the hip for every 4
foot section of Cobra* Hip Vent needed. Leave 12 inches of the hip uncut after each 36 inch opening, and
the lowest opening must stop at the mid-point of the hip and more than 24 inches in from the exterior
warm wall. Wider openings and slots below the midpoint of the hip will not improve ventilation and must
be avoided. Cut away the shingles first with a roofing knife, and then cut the deck with a circular saw. The
saw should be adjusted so that the rafters or trusses are not cut.
Note: The roof decking must be re-nailed to the rafter at the edge closest to the hip to compensate for the
nails removed when the hip slot was cut.
Ridge
Air Sloh
Hip Midpoint
I
I
I
I
I
FtdP Sid length nearest
midpoint may vary
N j
Deck
I
I
Eave
I
I
I
Must be at least 24"1610 mm)from the warm wall
Exterior Research and Design,I.I.C. Evaluation Report 01506.02.06-1112
Certificate of Authorization#9503 FBC NON-HVH2 EVALUATION FL6267-R12
GAF Revision 12:02/14/2017
Page 9 of 10
QO
TRINITY ERD
6.6.4 Sealant: Seal all cut-edges of the asphalt shingles to the roof sheathing along all sides of the hip air slot
openings, using a bead of ASTM C920 polyurethane sealant,to prevent water infiltration.
6.6.5 Orientation: Always install Cobra® Hip Vent with the "Towards Peak" arrows on the top surface of the
vent pointing up towards the peak of the roof.
6.6.6 Attachment: Cobra*Hip Vent is fastened to the deck starting at the bottom of the hip and then up along
the entire length of the hip (this includes un-cut portions of the hip). Fasten Cobra* Hip Vent to the deck
with the included 1%-inch inch long collated galvanized steel roofing nails, or longer corrosion resistant
roofing fasteners,to achieve penetration through plywood or OSB decks or minimum 3/4-inch embedment
into wood planks. Attach the Cobra® Hip Vent section through the pre-marked 6-inch increment nail
targets.
6.6.7 Joints &Terminations: Apply the subsequent Cobra® Hip Vent sections over the length of the hip using
the overlap/underlap tabs. For roofs with ridge vents, lengths of the hip vent must be butted tightly to
sections of ridge vents and install a 3 inch by 12-inch strip of self-adhering leak barrier over all junctions.
For roofs without ridge vents,sections of hip vent from adjacent hip runs must be mitered together tightly
where they intersect and install a 3 inch by 12-inch strip of self-adhering leak barrier over all junctions.
Refer to GAF published installation instruction for details.
6.6.8 Ridge Shingles: Cobra Hip Vent is then covered with ridge cap shingles and this entire assembly is nailed
to the sheathing with the included 1%-inch inch long collated galvanized steel roofing nails. Depending on
the field and ridge cap shingles used, longer length corrosion resistant fasteners may be necessary. The
ridge cap shingles are installed per the shingle manufacturer's instructions and Florida Product Approval,
with a minimum of two nails per shingle and a shingle to shingle nail spacing of 8 inches on center or less.
Refer to the shingle manufacturer's Florida Product Approval for ridge cap shingle fastening and sealing
requirements. Do not overdrive the nails or crush/compact the product during installation.
7. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
8. MANUFACTURING PLANTS:
Contact the manufacturer or the named QA entity for information on plants covered under Rule 61G20-3 QA
requirements.
9. QUALITY ASSURANCE ENTITY:
UL, LLC.—QUA9625;(847)664-3281
-END OF EVALUATION REPORT-
Exterior Research and Design,I.I.C. Evaluation Report 01506.02.06-1132
Certificate of Authorization#9503 FBC NON-HVHZ EVALUATION F1.6267-1112
GAF Revision 12:02/14/2017
Page 10 of 10
RECEIVED
JAN 0 3 2018 EXTERIOR RESEARCH 8, DESIGN, LLC.
Certificate of Authorization#9503
R ST. Lucie County, Permitting 353 CHRISTIAN STREET,UNIT#13
FtRINITY ERD OXFORD,CT 06478
PHONE:(203)262-9245
FAX:(203)262-9243
EVALUATION REPORT
GAF ;M i Evaluation Report 01506.01.08-1121
1 Campus Drive
FL10124-1119
Parsippany, NJ 07054 Date of Issuance:01/03/2008
Revision 21:08/26/2016
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code
sections noted herein.
DESCRIPTION: GAF Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. Trinity I ERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity)ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 6.
Prepared by: ,`�����t��►r��,^,,���,
Robert J.M.Nieminen P.E. '-,�S�"'•''ya The fa[smlleseal appearing was authorized byRobert Nieminen,
z '�4`t- �L i`sa, P.E.on 08/26/2016.This does not serve as an electronically signed
Florida Registration No. 59166,Florida DCA ANE1983 "� "'" document.signed,sealed hardcoples have been transmitted to the
Product Approval Administrator and to the named client
CERTIFICATION OF INDEPENDENCE:
1. TrinitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity I ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity)ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
TRINITY ERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: GAF Asphalt Roof Shingles, as produced by GAF, have demonstrated compliance with the
following sections of the Florida Building Code and Florida Building Code, Residential Volume through testing in
accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations /
Conditions of Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1507.2.4,R905.2.3 Physical Properties ASTM D1970 2009
1507.2.5,R905.2.4 Physical Properties ASTM D3462 2009
1507.2.7.1, R905.2.6.1 Wind Resistance ASTM D3161 2009
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2008
1507.2.7.1,R905.2.6.1 Wind Resistance TAS 107 1995
3. REFERENCES:
Entity Examination Reference Date
GAF(PDM 1915) Letter of Equivalency Seal-A-Ridge Impact Resistant IR 01/13/2012
PRI(TST 5878) Physical Properties GAF-025-02-01 03/27/2002
PRI(TST 5878) ASTM D3462 GAF-059-02-01 09/02/2004
PRI(TST 5878) ASTM D3462 GAF-080-02-01 05/25/2005
PRI(TST 5878) Physical Properties GAF-324-02-01 12/01/2011
PRI(TST 5878) Wind Driven Rain GAF-407-02-01 01/21/2013
UL(TST 1740) ASTM D3462 93NK629S 11/29/1993
UL(TST 1740) ASTM D3462 99NK43835 01/12/2000
UL(TST 1740) TA5 107 94NK9632 03/29/2000
UL(TST 1740) ASTM D3462 01NK06632 02/02/2001
UL(TST 1740) ASTM D3161,TAS 107 01NK9226 05/21/2001
UL(TST 1740) ASTM D3161 01NK37122 12/18/2001
UL(TST 1740) ASTM D3462 01NK37122 12/19/2001
UL(TST 1740) ASTM D3161,TAS 107 02NK12980 04/10/2002
UL(TST 1740) ASTM D3161,TAS 107 02NK30871 09/09/2002
UL(TST 1740) ASTM D3161 03CA5367 03/11/2003
UL(TST 1740) ASTM D3462 03NK26444 10/17/2003
UL(TST 1740) ASTM D3462 04NK13850 06/07/2004
UL(TST 1740) ASTM D3161 04NK138S0 06/23/2004
UL(TST 1740) ASTM D3161 04NK30546 03/10/2005
UL(TST 1740) ASTM D3462 04NK22009 05/06/2005
UL(TST 1740) ASTM D3161 04NK22009 OS/09/2005
UL(TST 1740) ASTM D3462 05NK27924 02/10/2006
UL(TST 1740) ASTM D3161 05NK27924 02/11/2006
UL(TST 1740) ASTM D3161,D3462 06CA18077 06/05/2006
UL(TST 1740) ASTM D3161,133462 06CA18074 06/16/2006
UL(TST 1740) ASTM D3161,D3462 06CA35251 10/18/2006
UL(TST 1740) ASTM D3462 06CA31603 12/01/2006
UL(TST 1740) ASTM D3161,D3462 06CA41095 12/27/2006
UL(TST 1740) ASTM D3161 07NK05228 03/13/2007
UL(TST 1740) ASTM D3161 06CA31611 04/04/2007
UL(TST 1740) ASTM D3161 06CA61148 04/09/2007
UL(TST 1740) ASTM D3161,D3462 07CA31742 11/08/2007
UL(TST 1740) ASTM D3161,D7158, D3462 08CA06100 03/13/2008
UL(TST 1740) ASTM D3161,D3462 07CASS908 04/01/2008
Exterior Research and Design,LLC. Evaluation Report 01506.01.08-1121
Certificate of Authorization#9503 F1.10124-1119
Revision 21:08/26/2016
Page 2 of 6
TRINITY ERD
Entity Examination Reference Date
UL(TST 1740) ASTM D3161,D3462 09CAlOS92 03/26/2009
UL(TST 1740) ASTM D3161,D3462 09CA06856 05/15/2009
UL(TST 1740) ASTM D3161,D7158,D3462 09NK06647 08/01/2009
UL(TST 1740) ASTM D3161,D71S8, D3462 09CA27281 08/27/2009
UL(TST 1740) ASTM D3161,D7158,D3462 10CA35554 03/05/2010
UL(TST 1740) ASTM D3161,D7158,D3462 IOCA13686 05/15/2010
UL(TST 1740) ASTM D3462 10CA07264 OS/27/2010
UL(TST 1740) ASTM D3462 10CA11953 10/29/2010
UL(TST 1740) ASTM D3161,D7158, D3462 1ONK11951 10/30/2010
UL(TST 1740) ASTM D3161,D7158, D3462 IONK12070 11/04/2010
UL(TST 1740) ASTM D3161,D7158,D3462 08CA06100 01/30/2010
UL(TST 1740) ASTM D3161,D7158,D3462 10CA53934 03/31/2011
UL(TST 1740) ASTM D3161,D7158,D3462 11CA48924 10/22/2011
UL(TST 1740) ASTM D3161,D7158,D3462 11CA47919 12/03/2011
UL(TST 1740) ASTM D3161,D7158,D3462 11CA48408 12/08/2011
UL(TST 1740) ASTM D3161,D7158,D3462 11CA48725 12/09/2011
UL,LLC.(TST 9628) ASTM D3462 12CA34891 10/12/2012
UL,LLC.(TST 9628) ASTM D3161,D7158,D3462 12CA58151 02/15/2013
UL,LLC.(TST 9628) ASTM D3161 12CA38083 02/26/2013
UL,LLC.(TST 9628) ASTM D3161 13CA32332 06/18/2013
UL,LLC.(TST 9628) ASTM D3161 13CA37934 08/02/2013
UL,LLC.(TST 9628) ASTM D3161,D71S8,D3462 4786875675 07/17/2015
UL,LLC.(TST 9628) ASTM D3161,D7158,D3462 4787434542 05/17/2016
UL,LLC.(QUA 9525) Quality Control Inspection Report,R21,Mobile,AL 12/28/2015
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Myerstown,PA 02/23/2016
UL,LLC.(QUA 9525) Quality Control Inspection Report,R21,Tuscaloosa,AL 02/26/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Michigan Cty,IN 03/02/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Shaffer,CA 02/18/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Savannah,GA 02/24/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Minneapolis,MN 02/09/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Mt.Vernon,IN 02/09/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Baltimore,MD 03/01/2016
UL,LLC.(QUA 9525) Quality Control Inspection Report,R21,Tampa,FL 02/29/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21, Dallas,TX 02/17/2016
UL,LLC.(QUA 9625) Quality Control Inspection Report,R21, Ennis,TX 02/03/2016
UL,LLC. (QUA 9625) Quality Control Inspection Report,R21, Fontana,CA 03/03/2016
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Marquis" WeatherMaO, Royal Sovereign' and Sentinel' are a fiberglass reinforced 3-tab asphalt roof
shingles.
4.1.2 Camelot", Camelot® II, Fortitude", Glenwood'", Grand Canyon°, Grand Sequoia, Grand Sequoia® IR,
Grand Sequoia® ArmorShieldTM, Monaco®, Sienna®, Timberline" American Harvest®, Timberline®
ArmorShield'" II,Timberline® Natural Shadow®, Timberline HDI, Timberline® Cool Series®,Timberline Ultra
HDPO and WoodlandQ9 are fiberglass reinforced, laminated asphalt roof shingles.
4.1.3 Slateline"'is a fiberglass reinforced 5-tab asphalt roof shingle.
4.2 Hip& Ridge Shingles:
4.2.1 Seal-A-Ridges Ridge Cap Shingles, Seal-A-Ridgem IR Impact-Resistant Ridge Cap Shingles, Seal-A-Ridge®
ArmorShield" Ridge Cap Shingles and Timbertex® Premium Ridge Cap Shingles are fiberglass reinforced, hip
and ridge asphalt roof shingles.
Exterior Research and Design,LLC. Evaluation Report 01506.01.08-R21
Certificate of Authorization#9503 FL10124-R19
Revision 21:08/26/2016
Page 3 of 6
TRINITY ERS
4.3 Accessory Starter Strips:
4.3.1 Pro-Start"' Eave/Rake Starter Strip Shingles and WeatherBlocker— Premium Eave/Rake Starter Strip Shingles
are starter strips for asphalt roof shingles.
4.3.2 QuickStart' Peel & Stick Starter Roll is a is a mineral-surfaced, fiberglass-reinforced, self-adhering SBS
modified bitumen starter strip, nominal 9-inch x 33 ft roll, for use with asphalt shingles with exposure of 6-
inch or less.
4.3.3 StarterMatch'" Sharter Strip Shingles are color-coordinated starter strips for use with Grand Canyon" and
Grand Sequoia' series asphalt shingles. StarterMatch`" are installed as the second starter for Grand
Canyon®and Grand Sequoia' series installations.
5. LIMITATIONS:
5.1 This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials
Directory for fire ratings of this product.
5.4 Wind Classification:
5.4.1 The GAF asphalt shingles noted in Section 4.1 are Classified in accordance with FBC Tables 1507.2.7.1 and
R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for
use in all wind zones up to Vasd= 150 mph (Vu,t= 194 mph). Refer to Section 6 for installation requirements
to meet this wind rating.
5.4.2 The GAF hip & ridge shingles noted in Section 4.2 are Classified in accordance with FBC Tables 1507.2.7.1
and R905.2.6.1 to ASTM D3161,Class F,indicating the shingles are acceptable for use in all wind zones up to
Vasd= 150 mph(V,,,t= 194 mph). Refer to Section 6 for installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies only to exposure category B or C, as defined in FBC 1609.4.3, and a
mean roof height of 60 feet or less. Calculations by a qualified design professional are required for
conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building
Code and F.A.C-Rule 61G20-3.
6. INSTALLATION:
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to GAF and shall hold current Florida Statewide Product Approval, or be
Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3.
6.2 Starter Shingles or Starter Strip:
6.2.1 Installation of Pro-Start Eave/Rake Starter Strip Shingles, WeatherBlocker Premium Eave/Rake Starter Strip
Shingles and QuickStart Peel &Stick Starter Roll shall comply with the GAF current published instructions.
6.3 Asphalt Shingles:
6.3.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using
minimum four (4) nails per shingle in accordance with FBC Sections 1507.2 or R905.2, with the following
exceptions:
i Camelot, Camelot II, Grand Canyon,Grand Sequoia, Grand Sequoia IR, Grand Sequoia ArmorShield, and
Woodland require minimum five(5)nails per shingle.
Slateline requires minimum six(6)nails per shingle.
Exterior Research and Design,LLC. Evaluation Report 01506.01.08-RZ1
Certificate of Authorization 119503 FL10124-R19
Revision 21:08/26/2016
Page 4 of 6
TRINITY ERD
6.3.2 Fasteners shall be in accordance with manufacturer's published requirements, but not less than FBC 1507.2.6
or R905.2.5. Staples are not permitted.
6.3.3 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. Contact the shingle manufacturer for details.
6.4 Hip&Ridge Shingles:
6.4.1 Installation of Seal-A-Ridge Ridge Cap Shingles,Seal-A-Ridge IR Impact-Resistant Ridge Cap Shingles and Seal-
A-Ridge Armor5hield Ridge Cap Shingles shall comply with the manufacturer's current published instructions
with a minimum two(2)nails, minimum 3/8-inch head diameter,per shingle and nominal 0.25-inch diameter
beads of Henkel"Loctite PL S30 Roof& Flashing Sealant".
11.5' Sealant
1• (292 m112"
Sellante
(25 mm) Enduil d'etancheite
(305 mm)
llavc
ail
65/8'-75/8' Clouer
(168-194 mm)
12"
(305 mm)
6.4.2 Installation of Timbertex Premium Ridge Cap Shingles shall comply with the manufacturer's current
published instructions with a minimum two (2) nails, minimum 3/8-inch head diameter, per shingle and
beads of Sonneborn NP1 Gun Grade Polyurethane Sealant or Henkel PL Roofing and Flashing Sealant.
1' (a
11 Is, u
1 Seanl
mml
(25 mrn; (25 mrSMIran4
t+ Sal lut d'itar iei
Oat
[Hauer (305 mm)
3'
1229 rnm)
11 1
1r
(3r05 mm)
6.4.3 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
Exterior Research and Design,LLC. Evaluation Report 01506.01.08-R21
Certificate of Authorization#9503 FL10124-R19
Revision 21:08/26/2016
Page 5 of 6
TRINITY ERD
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 61G20-3 QA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC—QUA9625; (847)664-3281
END OF EVALUATION REPORT-
Exterior Research and Design,LLC. Evaluation Report 01506.01.08-R21
Certificate of Authorization#9503 F1.10124.1119
Revision 21:08/26/2016
Page 6 of 6