HomeMy WebLinkAboutProduct Approval r i j
GREEK TAO BUILDING PRODUCTS
11 ' � Asphalt Shingles
j TECHNICAL SERVICES,LLC
Heritage®Vintage@ Basic Wind Speed(V,,,t): Max. 194 mph
(Phillipsburg) Basic Wind Speed(Vwd): Max. 150 mph j
Deck(HVHZ): In accordance with FBC requirements;
Solidly sheathed min. 19/32 in. plywood or wood plank for
new construction; Min. 15/32 � in. plywood existing
construction. j ';
Deck(Non-HVHZ): In accordance with FBC requirements;
Solidly sheathed min. 15/32 in. plywood or wood plank for
new construction; Min.7/116 in. OSB existing construction.
Underlayment: In accordance with FBC requirements.
Min.slope: 2:12 and in accordance ,with FBC' requirements. Refer to
the manufacturer's application instructions when installing
shingles at slopes greaterlthan 211:12.
Installation(HVHZ): Installed with 5 in. exposure in accordance with RAS 115
and manufacturer's published j,installaltion instructions.
Shingles shall be attached using;'16 Nail Pattern" detailed
below.
Installation (Non-HVHZ): Installed with 5 in. exposure in accordance with FBC
requirements and manufacturer's published installation
instructions. Shingles shall be attached using either"5 Nail
Pattern"or T Nail Pattern"detailed below.
I f 5 1 i{I I
ES�p9"..I•l.1E'd
I SII
Yl.
Figure 12. Heritage®Vintage® I
5 Nail Pattern (non-HVHZ only)
I
xrr=r —sa+r gar— —�aie--► _xe�
Figure 13. Heritage®Vintage®
6 Nail Pattern j
I'" f
TBP15001.4 FL18355-R4 j I Page 8 of 11
This evaluation report is provided for State of Florida product approval under Rule 61G20-3.I The manufacturer shall notify CREEK
Technical Services, LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other!product'attributes
ttributes that are not
specifically addressed herein.
j
I i4I
I'
t
1
TA I i0 BUILDING PRODUCTS
CREEK ! Asphalt Shingles
TECHNICAL SERVICES,LLC
Hip&Ridge Basic Wind Speed(Vu,t): Max. 194 mph
(Frederick&Joplin) Basic Wind Speed(Vasd): Max. 150 mph
Deck(HVHZ): In accordance with FBC requirements;
Solidly sheathed min. 19/32 in. plywood or wood plank for
new construction; Min. 15/32; in. plywood existing
construction. f
Deck(Non-HVHZ): In accordance with FBC requirements;
Solidly sheathed min. 15/32 in. plywood or wood plank for
new construction; Min.7/16 in. OSB existing construction.
Underlayment: In accordance with FBC requirements. '
Min.slope: 2:12 and in accordance with FBC requirements.
Installation: Installed with 5-1/8 inch exposure� in accordance with the
FBC and manufacturer's published installation instructions.
The direction of the exposed end shall be away from the
prevailing wind. J
i
i
Direction.prevailing wind
art 5=1f8" exosurep
here ,�1' ,
I ' I
here . .....'ox osure
i Figure 1 R
I
I
' I I
5- ' ; ,I•
jar
Fastener" ,rf �1,
Fas#
i
1 31
Figure 2 Figure.1;
114°
Figure 14. Hip&Ridge(Frederick&•Joplin) I i
I
it I
I,i !
i ,
I� I
i
TBP15001.4 FL18355-R4 I 1,1 Page 9 of 11
This evaluation report is provided for State of Florida product approval under Rule 61G20 31 The manufacturer shall notify CREEK
Technical Services, LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use,or others iroductiattributes that are not
specifically addressed herein. '
ISI
� I I•!
CREEK TAMKO BUILDING PRODUCTS
! Asphalt Shingles
TECHNICAL SERVICES,LLC
II
. I
Vintage®Hip&Ridge Basic Wind Speed(Vuit): Max. 194 mph
(Phillipsburg) Basic Wind Speed(Vasd): Max. 150 mph I
Deck(HVHZ): In accordance with FBC requirements;
Solidly sheathed min. 19%32 in. plywood or wood plank for
new construction; Mini 15/32'1 in. plywood existing
construction.
Deck(Non-HVHZ): In accordance with FBC requirements,-
Solidly
lquirements,-
Solidly sheathed min. 15/32 in. plywood or wood plank for
new construction; Min.7/16 in.OSB existing construction.
Underlayment: In accordance with FBC requirements.
Min.slope: 2:12 and in accordance with FBC requirements.
Installation: Installed with 5 inch exposure in,accordance with the FBC
and manufacturer's published installation instructions. The
direction of the exposed end shall be away from the
prevailing wind.
i
I
Directiow dt prevailino[Wind
Start W exposure:
ere-
li
.Start II �
liege" 5" exposur.'e.
Figure'l j !
er
fasten
Fastenei
Figure:'2 .Figure3 j
I
Figure 15. Vintage®Hip&Ridge(Phillipsburg)
i
+ I 1
i
Ij
I
TBP15001.4 FL18355-R4 ! Page 10 of 11
This evaluation report is provided for State of Florida product approval under Rule 61G20-3: The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the durationifor which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other.product attributes that are not
specifically addressed herein.
i I
' � I
Ii
TAMKO BUILDING PRODUCTS
CREEKi Asphalt Shingles
I
TECHNICAL SERVICES,LLC
I II I
LIMITATIONS ,l
i I I
1) Fire Classification is not within the scope of this evaluation. j
2) The roof deck and the roof deck attachment shall be designed by others to meet the minimum design loads
established for components and cladding and in accordance with FBC requirements;
3) The mean roof height shall be restricted to a maximum 33 ft in the HVHZ. I ,
4) Classification to ASTM D 7158 applies to exposure B&C with a building mean roofjheight of 60-ft or less.
5) Deck substrates shall be clean, dry, and free from any irregularities and ebris.i;All fasteners in the deck
shall be checked for protrusion and corrected prior to underlayment application. i
6) Shingles shall be installed starting at the eave in horizontal layers such'that the laps shed water from the
deck.
7) Installation of the evaluated products shall comply with this report, the FBG,, and the manufacturer's
published application instructions. Where discrepancies exist between these sources, the more restrictive
j and code compliant detail shall prevail.
8) All products listed in this report shall be manufactured under a quality assuranceprogram in compliance with
Rule 61 G20-3.
I
COMPLIANCE STATEMENT
The products evaluated herein by Zachary R. Priest, P.E. have demonstrated compliance With the Florida Building
Code,6t'Edition(2017)as evidenced in the referenced documents submitted by the named m anufacturer.
iII11111114 . I
��RY R; p���i,
2017.09.2 5
' >' '•. j
No 74'021 1�1 :31 :41
-041001
STATE OF /
' A/: Zachary R. Priest, P.E. I I
R N. Florida Registration.No.74021
Organization No.ANE11666
i I
CERTIFICATION OF INDEPENDENCE i
CREEK Technical Services, LLC does not have,nor will it acquire,a financial interest in any,lcompany manufacturing or distributing
products under this evaluation.
� I
j CREEK Technical Services,LLC is not owned,operated,or controlled by any company manufacturing or distributing products under
j this evaluation.
I I
Zachary R. Priest, P.E:does not have, nor will acquire, a financial interest in any company manufacturing or,distributing products
under this evaluation.
II
Zachary R.Priest,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
I.
product.
I,� I
I I'
I ,
I
I
END OF REPORT
TBP15001.4 FL18355-R4 I Page 11 of 11
This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the duration1for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other'product attributes that are not
j specifically addressed herein.
, II
� I
II
j I
ISO
BCIS Home Log In I User Registration + Hot Topics Submit Surcharge j Stats&Facts Publications FBC Staff i BCIS Site Map j Links Search s
111 II
Rod,
'Product Approval
r
,FUSER:Public User I
Product Approval Menu>Product or Application Search>Application List>Application Detail i r
* FL# FL10758-R7
I '
Application Type Revision
Code Version 2017
Application Status Approved
i
Comments
r
Archived i
Product Manufacturer Owens Corning j
Address/Phone/Email One Owens Corning Parkway j
Toledo,OH 43659 j
(740)404-7829 I
greg.keeler@owenscorning.com ,
I �
Authorized Signature Greg Keeler
I ! �
greg.keeler@owenscorning.com
� I
Technical Representative Greg Keeler
Address/Phone/Email 2790 Columbus Road i
Granville,OH 43023
(740)321-6345 j
greg.keeler@owenscorning.corn i I
i
Quality Assurance Representative
I
Address/Phone/Email
Category Roofing j
Subcategory Roofing Accessories that are an Integral Part of the Roofing System
I f
; i
Compliance Method Evaluation Report from a Florida Registered'Architect or a Licensed Florida
Professional Engineer
Evaluation Report-Hardcopy Received
r
Florida Engineer or Architect Name who developed Zachary R. Priest j
the Evaluation Report
Florida License PE44021
Quality Assurance Entity UL LLC
Quality Assurance Contract Expiration Date 04/13/2018 I
Validated By Locke Bowden
I
fkl Validation Checklist- Hardco I py Received
I
Certificate of Independence FL10758 R7 COI 1 '
03.3 2017 FBC Evaluation Report Owens
Corning Vents final.odf
I
r
li
� Referenced Standard and Year(of Standard) i
I �
II I
Equivalence of Product Standards j
Certified By I
' I I
Sections from the Code
1708.2
r
I I �
I
I
i � '
,
Product Approval Method Method 2 Option B
i
Date Submitted 09/30/2017
Date Validated 10/04/2017
Date Pending FBC Approval 10/08/2017
Date Approved 12/12/2017
I i
Summary of Products
FL# Model,Number or Name Description
10758.1 VentSure 4-Foot Strip Heat and Copolymer plastic low profile attic ridge vents for installation in
Moisture Ridge Vents shingle roof systems
Limits of Use Installation Instructions
Approved for use in HVHZ: No FL10758 R7 IIS OCR14003.3 2017 FBC Evaluation Report
Approved for use outside HVHZ:Yes Owens Corning Vents final.pdf
Impact Resistant:. N/A Verified By: Zachary R. Priest 74021
Design Pressure: N/A Created by Independent Third Party:Yes
Other: Refer to evaluation report Evaluation Reports j
FL10758 R7 AE OCR14003.3 2017 FBC Evaluation Report
Owens Cornina Vents final.odf i
Created by Independent Third Party:Yes
10758.2 VentSure Low Profile Slant Back Roof Galvanized metal I roof vent j
Vent With Exterior Louver I
Limits of Use Installation Instructions
Approved for use in HVHZ: No FL10758 R7 II OCR14003.3 2017 FBC Evaluation Report
Approved for use outside HVHZ:Yes Owens Cornina'Vents final.ndf
Impact Resistant: N/A Verified By: Zachary R. Priest 74021
Design Pressure: N/A Created by Independent Third Party:Yes
Other: Refer to evaluation report. Evaluation Reports I
FL10758 R7 AE OCR14003.3 2017 FBC Evaluation Report
Owens CorninciVents final.pdf
Created by Independent,Third Party:Yes
i
10758.3 VentSure Rigid Roll Ridge Vent Ridge Ventilation System'
Limits of Use Installation Instruction's
Approved for use in HVHZ: No FL10758 R7 II OCRI4003.3 217 FBC Evaluation Report
Approved for use outside HVHZ:Yes Owens Cornino,Vents final.odf I
Impact Resistant: N/A Verified By: Zachary R..Ph,est 74021
Design Pressure: N/A Created by Independent Third Party:Yes
Other:Refer to evaluation report. Evaluation Reports j
FL10758 R7 AE OCR14003.3 2017 FBC Evaluation Report
Owens COrnino'Vents fi6al.pdf
I
Created by Independent'Third Party:Yes
aac€c. FEE t]
I i
I I
Contact Us::2601 Blair Stone Road,Tallahassee FL 32399 Phone:850-487-1824
i The State of Florida is an AA/EEO employer.Copyright 2007-2013 State of Florida.::Privacy Statement::dccessibility Statement::Refund Statement
Under Florida law,email addresses are public records.If you do not want your e-mail address released in response to,a public-(records request,do not send electronic
mall to this entity.Instead,contact the office by phone or by traditional mail.If you have any questions,please contact 850.487.1395.*Pursuant to Section
455.275(1),Florida Statutes,effective October 1,2012,licensees licensed under Chapter 455,F.S.must provide theiDepartment with an email address If they have
one.The emails provided may be used for official communication with the licensee.However email addresses are pdblic record.l If you do not wish to supply a personal
address,please provide the Department with an email address which can be made available to the public.To determine if you are a licensee under Chapter 455,F.S.,
please click here.
Product Approval Accepts: i
i
0�L
0M ; I
i
i
I Ii
i I
I I
i ij I
i .
I �
I
' Certificateof Authorization No.29824
CREEK �, 17520 Edinburgh Dr
I I Tampa, FL 33647
TECHNICAL SERVICES, LLC (813)480-3421
I !
EVALUATION REPORT FLORIDA BUILDING CODE,6T"EDITION(2017)
I
Manufacturer: OWENS CORNING ROOFING AND ASPHALT LLC l sued SI ptember30, 2017
1 Owens Corning Parkway
Toledo, OH 43657
(800)438-7465
www.owenscorning.com
Ii I
Quality Assurance: UL LLC(QUA9625) i
I
SCOPE
Category: Roofing
Subcategory: Roofing Accessories that are an Integral Part of the Roofing System
Code Sections: 1708.2
Properties: Roof Ventilation
I
REFERENCES
ED-tilt Report No. Sta l dard j(� Year
Architectural Testing,Inc(TST1558) 01-38660.04 TASi 100(A) i ; 1995
Architectural Testing,Inc(TST1558) 01-38660.05 TAS 100(A) 1995
Architectural Testing,Inc(TST1558) C1774.01-109-18 TAS 100(A) I 1995
ASTM D 635! 2010
ASTM D 1929 2012
1 ASTM D 2843 2010
PRI Construction Materials Technologies(TST5878) AVIG-005-02-01 ASTM D 635, I 2010
ASTM D 1929 2012
ASTM D 2843 2010
PRI Construction Materials Technologies(TST5878) AVIG-006-02-01 ASTM G 155 2005a
PRI Construction Materials Technologies(TST5878) OCF-111-02-01 ASTM D 635;' 2010
ASTM D 1929 2012
ASTM D 2843 2010
PRI Construction Materials Technologies(TST5878) OCF-112-02-01 ASTIM G 155 f 2005a
PRI Construction Materials Technologies(TST5878) OCF-116-02-01 TAS 100(A) ' 1995
PRI Construction Materials Technologies(TST5878) OCF-223-02-01 TAS 100(A) i 1995
j PRI Construction Materials Technologies(TST5878) OHI-007-02-01 TAS 100(A) i 1995
I
I.I i
I ;
I !
I
I '
I i !
III
OCR14003.3 FL10758-R7 Page 1 of 5
This evaluation report is provided for State of Florida product approval under Rule 61G20-3.I The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the duration
Ifor which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use,,1or other product attributes that are not
specifically addressed herein.
i
!
i
I
1 ,
I.I
OWENS CORNING ROOFING�AND ASPHALT LLC
CREEKVentSure@ Roof Ventilation
TECHNICAL SERVICES,LLC
I
PRODUCT DESCRIPTION AND APPLICATION j
I
VentSureu4-Foot Strip 1-1/4" x 14-7/8" x 48" low-profile attic ridge vent clnsisting'of a two-layer nylon-
Heat and Moisture Ridge polyester composite. Available with or without a polyester fabric moisture barrier for
Vents: installation in shingle roof systems. ;
48° -.
Ii
14-7/8" II
' II
Deck Type: Roof deck shall be constructed of closely fitted sheathing for new or existing
construction. Roof deck shall be designed and installed in accordance with FBC
requirements.
Roof slope: Minimum 3:12 to maximum 16/12
Installation Height: Maximum 60-ft
Attachment Method: Cut a 2-inch opening (1-inch on each side of the ridge) centered in Ithe deck at the
ridge for ventilation. The slot shall terminate approximately 6'-inches from the rake
edges. Apply a %-inch wide bead of ASTM D 4586 'roofing cement along the entire
length of the outside edges of the vent to seal the vent to the field shingles, taking
care to not completely cover the weep slots in the vent. Center tha vent over the
opening and fasten to the deck using the 11 ga. 2'/-inch galvanized ring shank nails
(shall comply with FBC Section 1506.5) provided with the vent. Fasteners are to be
installed on both sides of the vent 1, 12,24, 36, and 47-inche6;from the start of each
vent piece.
fi
Prepare the adjacent vent section by applying the roofing cement along the edges,
snap together with fixed vent, and fasten to the deck'n the same manner as the first
section. Fasten the ridge shingles over the vent to the deck on the I marked "shingle nail line" with two (2) minimum 11 ga. 2%-inch galvanized ring shank roofing nails
(shall comply with FBC Section 1506.5) provided with the vent or asl directed by the
shingle manufacturer's installation instructions.
I
j Allowable Roof Coverings: Asphalt shingles
• I,I
I
I
I`I I
OCR14003.3 FL10758-R7 I ; Page 2 of 5
This evaluation report is provided for State of Florida product approval under Rule 61G20-3.• The manufacturer shall notify CREEK
Technical Services, LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use,'or other product attributes that are not
specifically addressed herein.
I � I
Pp
OWENS CORNING ROOFING AND ASPHALT LLC
CREEK ventsu ie® Roof Ventilation
TECHNICAL SERVICES,LLC (; I
' Y I
VentSure Low Profile 18"x 24"x 2-3/16"(32"x 23"flange base)static off-ridge vent composed of ASTM
Slant Back Roof Vent A653 galvanized steel (available with painted finish). Material shall conform with
with Exterior Louver: FBC Section 1507.4.3. i 4
1
1 91
' F
s
Deck Type: Roof deck shall be constructed of closely fitted sheathing for new or existing
construction. Roof deck shall be designed and installed in,Accor i ante with FBC
requirements.
Roof slope: Minimum 3:12 i I
Installation Height: Maximum 33-ft
I Attachment Method: Cut an 11 x 11-inch hole through wood sheathing only approximately 18-inches from
the ridge. Apply 1/4-inch thick by 3-inch wide bed of ASTM1 D 4586 roofing cement
around inner and outer flange. Place vent directly over the Ilole, ensuring the vent
j sits flat on the roof. Fasten vent 4-inches o.c. and 1-inch from outside edge of flange
with minimum 12 ga. ring shank roofing nails (shall comply with FBC Section
1506.5), ensuring %-inch penetration through wood deck ( IMIinimum 18 nails per
vent). p I
Install baffle in '/-inch bed of ASTM D 4586 roofing cement and secure with
minimum 12 ga. ring shank roofing nails (shall comply with:jFBC Section 1506.5)
spaced 8-inches o.c. (total of (3) nails) while ensuring '/4ch penetration through
wood deck. Seal all nails and vent flange with ASTM D 4586 roofing cement.
I;r
i
Allowable Roof Coverings: Asphalt shingles I'j
I l
I
�l I
i
OCR14003.3 FL10758-R7 I Page 3 of 5
This evaluation report is provided for State of Florida product approval under Rule 61G20-3.,I The manufacturer shall notify CREEK
Technical Services, LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use,ior other product attributes that are not
specifically addressed herein. I
� 'I j
I I
I
CD � OWENS CORNING ROOFING:AND ASPHALT LLC
j� VentSureO Roof Ventilation
TECHNICAL SERVICES,LLC I,'
I I
VentSureo Rigid Roll 5/8"x 11-1/4"x 20'attic ridge vent composed of high density polypropylene with a
Ridge Vent: spun-bond polypropylene fabric. j
00
-fly s
Deck Type: Roof deck shall be constructed of closely fitted sheathinlg for new or existing
construction. Roof deck shall be designed and installed in'accordance with FBC
requirements.
I � I
Roof slope: Minimum 2:12 to maximum 20:12
Installation Height. Maximum 60-ft
Attachment Method: Cut a 2-inch opening (1-inch on each side of the ridge) centered in Le deck at the
ridge for ventilation. The slot shall terminate approximately 12; -inches from the rake
edges. Apply a continuous bead of polyurethane adhesive sealant along the entire
length of the outside edges of the vent to seal the vent to the,field shingles. Center
the vent over the opening and fasten the vent 24-finches oic. to 'the deck using
minimum 12 ga. ring shank roofing nails (shall comply with FBC Section 1506.5),
ensuring%-inch penetration through wood deck.
Fasten the ridge shingles over the vent to the deck on the marked "shingle nail line"
with two(2) minimum 12 ga. ring shank roofing nails (shall comply with FBC Section
1506.5) or as directed by the shingle manufacturer's installation instructions,
ensuring%-inch penetration through wood deck..Outside edges of thie shingles shall
be sealed with flashing cement. I
i I
Allowable Roof Coverings: Asphalt shingles
• i I �
I
II
I
LIMITATIONS
1) Fire Classification is outside the scope of this evaluation. i !
2) This report is not for use in the HVHZ. j
3) The roof deck and deck attachment shall be designed by others in accordance with the FBC.
4) All products listed in this report shall be manufactured under a quality assurance program lin compliance with
Rule 61 G20-3.
5) Owens Corning vents shall be installed in strict compliance with' this evaluation report and the
manufacturer's published installation instructions. In the event of conflict, the more restrictive installation
shall be enforced. I
6) Deck substrates shall be clean, dry, and free from any irregularities and debris.;,;All faslteners in the deck
shall be checked for protrusion prior to installation.
! 7) Installation of the roof assembly is outside the scope of this evaluation. I
8) Owens Corning vents are intended to provide passive ventilation for an enclosed attic in residential
construction applications. I
I
OCR14003.3 FL10758-R7 I ! Page 4 of 5
! This evaluation report is.provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK
Technical Services, LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not
specifically addressed herein.
I �
• I
CREEK OWENS CORNING ROOFING AND ASPHALT LLC
VentSure® Roof Ventilation
TECHNICAL SERVICES,LLC I
I
I
COMPLIANCE STATEMENT
� I
The products evaluated herein by Zachary R. Priest, P.E. have demonstrated compliancIe!with the Florida Building
Code;,6U'Edition(2017)as evidenced in the referenced documents submitted by the named,manufacturer.
P'' �':' 2017 09 30
Na. 74021 15:16:17
r
Z.
.c� b h6igmdbf Srfiary-Glial yA:.:.
rte:13 :S :�` -04'00,STATE O F " ,
0 R Q C?�s` Zachary Ri.
Priest,iPLE. I
N;A1 �� Florida Registration{No.74021
��i��p -. ��,
01211ll�r�;��� Organization No.AINE9641
I IS
iII
CERTIFICATION OF INDEPENDENCE
CREEK Technical Services, LLC does not have, nor will it acquire,a financial interest in any,companyimanufacturing or distributing
products under this evaluation. I
CREEK Technical Services,LLC is not owned,operated,or controlled by any company manufacturing'or distributing products under
this evaluation.
Zachary R. Priest, P.E.does not have, nor will acquire, a financial interest in any company;manufacturing or,distributing products
under this evaluation. !
! Zachary R.Priest,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
C product. '!
I i4�
I;
I
,I
fir I
Ir,
I
i I
, I
r
END OF REPORT
i iI i
OCR14003.3 FL10758-R7 r l j Page 5 of 5
This evaluation report is provided for State of Florida product approval under Rule 61G20-3.j The manufacturer shall notify CREEK
Technical Services, LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use,for other'product attributes that are not
specifically addressed herein.
i
li
I �
BCIS Home 's Log In User Registration Hot Topics i Submit Surcharge [ Stats&Facts j Publications S ir
F"BC Staff BCIS Site Map I Links I Search
. R IZ E..
I i
Product Approval
FUSER:Public User
i Product Approval Menu>Product or Application Search>Aoolication List>Application Detail j
FL# FL18355-R4
Application Type Revision I I
I
Code Version 2017
Application Status Approved i I
I
Comments
Archived
l � I
Product Manufacturer TAMKO Building Products,Inc. I i
. i
Address/Phone/Email PO Box 1404
Joplin, MO 64802
(417)624-6644 Ext 2305'
kerri_eden@tamko.com
i
Authorized Signature Kerri Eden
kerri_eden@tamko.com
Ii
Technical Representative Kerri Eden
Address/Phone/Email PO Box 1404
Joplin,MO 64802
(417)624-6644 Ext 2305
kerri_eden@tamko.com
i
I I
Quality Assurance Representative I ;
Address/Phone/Email I
Category Roofing
Subcategory Asphalt Shingles
! Compliance Method Evaluation Report from a Florida Registered'Architect or a Licensed Florida
Professional Engineer I
EJ Evaluation Report-Hardcopy Received
I j
Florida Engineer or Architect Name who developed Zachary R. Priest I
the Evaluation Report
Florida License PE-74021
Quality Assurance Entity UL LLC
Quality Assurance Contract Expiration Date 01/07/2019 I '
Validated By Locke Bowden I
iia Validation Checklist- Hardcopy)Received
I
I ' I I
Certificate of Independence FLIB355 R4 COI TBP150014201 7;FESC Eval Report Shingles final.odf
II j
Referenced Standard and Year(of Standard) Standard i Year
ASTM D 3161 I I 2016
ASTM D 3462 2010
i
ASTMD D 7158 j 2011
j TAS 100 1995
Equivalence of Product Standards j
Certified By Approved Testing Lab
FL18355 R4 Eauiv UL letter for standards for FBC 2017.odf
, I
ii
i
I
Sections from the Code
� I
l I !
Product Approval Method Method 1 Option D l
Date Submitted 09/25/2017
Date Validated 09/27/2017
Date Pending FBC Approval 10/08/2017
Date Approved 12/12/2017 I:
'I I
I
Summary of Products
FL# Model,Number or Name Description
18355.1 Glass-Seal, Elite Glass-Seal, ASTM D 3462 asphalt shingles and hip and ridge shingles
Heritage, Heritage Premium,
Heritage Woodgate,Heritage !
Vintage,Hip and Ridge,and Vintage I I l
Hip and Ridge Shingles I
Limits of Use a Installation Instructions
Approved for use in HVHZ:Yes FL18355 R4 IIi TBP15001.4 2017 FBC Eval Report Shinoles
Approved for use outside HVHZ:Yes fins df I i
Impact Resistant: N/A Verified By: Zachary R.Priest PE174021
Design Pressure: N/A Created by Independent Third Party:Yes
Other:See evaluation report for limits of use. Evaluation Reports 1`,j 1
FL18355 R4 AtTBP15001.4 2017 FBC Eval Reoort Shinoles
final. dI
Created by Independent nThird Party:Yes
Eck] faext I'
II
Contact Us::2601 Blair Stone Road,Tallahassee FL 32399 Phone:850-467-1824
I The State of Florida is an AA/EEO employer.Copyright 2007-2013 State of Florida.::Privacy Statement::Accessibility Statement::Refund Statement
Under Florida law,email addresses are public records.If you do not want your e-mail address released In response to.a public-records request,do not send electronic
mail to this entity.Instead,contact the office by phone or by traditional mail.If you have any questions,please.contact 850.487.1395.*Pursuant to Section
455.275(1),Florida Statutes,effective October 1,2012,licensees licensed under Chapter 455,F.S.must provide the Department with an email address if they have
one.The emails provided may be used for official communication with the licensee.However email addresses are public record.!If you do not wish to supply a personal
address,please provide the Department with an email address which can be made available to the public.To determine if you are a licensee under Chapter 455,F.S.,
please click here
•I Product Approval Accepts: fel
I
i
�i
I
I
I,I I
i , I
i�
I �
I �
,•i I
I,I I
r
j
Certificate of Authorization No.29824
CREEK ! 17520 Edinburgh Dr
iTampa,FL 33647
TECHNICAL SERVICES, LLC ; I (813)480-3421
I
EVALUATION REPORT FLORIDA BUILDING CODE,6Tj EDITION(2017)
Manufacturer: TAMKO BUILDING PRODUCTS Issued September 25, 2017
1 220 West 4v'Street I '
Joplin, MO 64801 i I
(417)624-6644
Manufacturing Plants: Joplin, MO
Phillipsburg, KS
! Frederick, MD I,
I Dallas,TX
Tuscaloosa,AL I
Quality Assurance: UL LLC(QUA9625)
I
I '�I
SCOPE
I
Category: Roofing
Subcategory: Asphalt Shingles
Code Sections: 1504.1.1, 1507.2.5, 1507.2.7.1, 1523.6.5.1
Properties: Physical properties,Wind Resistance,Wind Driven Rain I 1
REFERENCES
1 itl
' I
I
Enti Report No. Standard I I Year
PRI Construction Materials Technologies(TST5878) TAP-043-02-01 TAS 100 I. 1995
r PRI Construction Materials Technologies(TST5878) TAP-051-02-01 TAS 100 j',� 1995
PRI Construction Materials Technologies(TST5878) TAP-054-02-01 TAS 100 11995
j PRI Construction Materials Technologies(TST5878) TAP-114-02-01 TAS 100 1995
PRI Construction Materials Technologies(TST5878) TAP-117-02-01 TAS 100 JI 1995
PRI Construction Materials Technologies(TST5878) TAP-130-02-01 TAS 100 I 1995
PRI Construction Materials Technologies(TST5878) TAP-131-02-01 TAS 100 I 1995
PRI Construction Materials Technologies(TST5878) TAP-165-02-01 TASI 100 j 1995
PRI Construction Materials Technologies(TST5878) TAP-280-02-01 TASI 100 I 1995
PRI Construction Materials Technologies(TST5878) TAP-303-02-01 TAS'100 j,j 1995
PRI Construction Materials Technologies(TST5878) TAP-307-02-01 TASI 100 ! 1995
PRI Construction Materials Technologies(TST5878) TAP-314-02-01 Rev 2 TAS]100 1995
PRI Construction Materials Technologies(TST5878) TAP-315-02-01 ASTM D 638,1;+� 2008(2013)e1
PRI Construction Materials Technologies(TST5878) TAP-317-02-01 TAS!100 1 ! 1995
UL LLC(TST9628) 02NK9507 ASTM D 31611 2016
UL LLC(TST9628) 04NK24366 ASTM D 34621 2010A
UL LLC(TST9628) 05NK28006 ASTM D 638'1 2008(2013)e1
UL 2390 j
ASTM D 7158 2011
UL LLC(TST9628) 06NK03898 ASTM D 316!11 2016
ASTjM D 3462; 2010A
UL LLC(TST9628) 08CA59132 ASTM D 3161 2016
j UL LLC(TST9628) 09NK07896 ASTM D 31611,1 2016
ASTM D 3462 2010A
UL LLC(TST9628) 1 OCA50498 ASTjM D 3462 2010A
UL LLC(TST9628) 1 OCA64882 ASTM D 31611 2016
UL LLC(TST9628) 11NK14014 ASTM D 3161 j 2016
ASTM D 34621 2010A
UL LLC(TST9628) 12CA24551 ASTM D 3161, 2016
UL LLC(TST9628) 4786110543 ASTM D 6381' 2008(2013)el
UL LLC(TST9628) 4787043752 ASTM D 31611 2016
UL LLC(TST9628) 4787148748 ASTM D 7158 2011
ASTM D 3161 h 12016
ASTM D 34621 2010A
CREEK Technical Services LLC(ANE11669) T131315001.3 Calculations] I 2017
! TBP15001.4 FL18355-R4 I Page 1 of 11
1 This evaluation report is provided for State of Florida product approval under Rule 611320-3.1 The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout ttie durationjfor which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other!product attributes that are not
specifically addressed herein.
i
k
1
TAI K'O BUILDING PRODUCTS
CREEK i Asphalt Shingles
TECHNICAL SERVICES,LLC
i
I
PRODUCT DESCRIPTION
Elite Glass-Seal® 12-1/4" x 36", ASTM D 3161, Class F and ASTM D 7158, Class H self-sealing, 3-tab
(Frederick,Joplin& asphalt shingle with fiberglass mat coated on both sides with asphalt and surfaced with
Tuscaloosa) ceramic granules complying with ASTM D 3462.
i
Glass-Seal 12-1/4" x 36", ASTM D 3161, Class F and ASTM D 7158, Class H self-sealing, 3-tab
(Frederick& asphalt shingle with fiberglass mat coated on both sides with asphalt land surfaced with
Tuscaloosa) ceramic granules complying with ASTM D 3462. i
' i
Glass-Seal 12-1/4°x 36", ASTM D 7158, Class H self-sealing, 31b asplialt shingle with fiberglass
(Joplin) mat coated on both sides with asphalt and surfaced with ceramic granules complying
with ASTM D 3462. Shingles shall be used in the non-lHVHZ only.
Heritage@ 13-1/4" x 39-3/8", ASTM D 3161, Class F and ASTM D 7158, Class H fiberglass
(Dallas,Frederick, reinforced, laminated architectural asphalt shingle surfaced; with mineral granules.
Joplin,Phillipsburg& complying with ASTM D 3462. I I
r
Tuscaloosa)
Heritage@ Premium 13-1/4" x 39-3/8", ASTM D 3161, Class F and ASTM D 7158, Class H fiberglass
(Dallas,Frederick, reinforced, laminated architectural asphalt shingle;surfaced with imineral granules
i Phillipsburg& complying with ASTM D 3462.
Tuscaloosa)
Heritage@ Premium 12" x 36", ASTM D 3161, Class F and ASTM D 7158, Class;H fiberglass reinforced,
(Frederick) laminated architectural asphalt shingle surfaced with mineral granules complying with
ASTM D 3462.
Heritage@ Vintage@' 17-1/2"x 40",ASTM D 3161, Class F and ASTM D 7158, Class H fiberglass reinforced,
i (Phillipsburg) laminated architectural asphalt shingle surfaced with mineral 'granule's complying with
ASTM D 3462.
I II
Heritage@ Woodgate 13-1/4" x 39-3/8", ASTM D 3161, Class F and ASTM D 7158, Class H fiberglass
(Dallas&Frederick) reinforced, laminated architectural asphalt shingle, surtac'dl with mineral granules
complying with ASTM D 3462.
` Heritage@ Woodgate 12" x 36-3/8", ASTM D 3161, Class F fiberglass reinforced; laminated architectural
(Frederick) asphalt shingle surfaced with mineral granules complying with,ASTM D 3462. Shingles
shall be used in the non-HVHZ only.
i
Hip and Ridge Shingles 12-1/4" x 12", ASTM D 3161, Class F fiberglass reinforced, hip land ridge asphalt
(Frederick&Joplin) shingle surfaced with mineral granules complying wit til ASTM D�3462.+
Vintage@ Hip and Ridge 12" x 12 ASTM D 3161, Class F fiberglass reinfor led, MIDI and ridge asphalt shingle
(Phillipsburg) surfaced with mineral granules complying with ASTM D 3462.1 ,
I !
lI
I �
i 1 I I
i I
TBP15001.4 FL18355-R4 ; Page 2 of 11
This evaluation report is provided for State of Florida product approval under Rule 61G20-3.I The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use,for other product attributes that are not
specifically addressed herein.
i
iil I
� I I
I �
1����i'n TAMKO BUILDING PRODUCTS
i Asphalt Shingles
i
l TECHNICAL SERVICES,LLC
I
k �
INSTALLATION
Elite Glass-Seal® Basic Wind Speed(V„ir): Max. 194 mph
(Frederick,Joplin& Basic Wind Speed(Vasa): Max. 150 mph I;
Tuscaloosa) Deck(HVHZ): In accordance with FBC requirements;
& Solidly sheathed min. 19/32 in. plyiwood for wood plank for
Glass-Seal new construction; Min: 15/32 in. plywood existing
(Frederick,Joplin(Non- construction.
HVHZ)&Tuscaloosa) Deck(Non-HVHZ): In accordance with FBC requirements;
Solidly sheathed rein. 15%;32 in. plywood for wood plank for
new construction; Min. 7/16 in. OSB existing construction.
Underlayment: In accordance with FBC requirements.
Min.slope: 2:12 and in accordance with FBC i requirements. Refer to
the manufacturer's application instructions when installing
shingles at slopes greater,than 21,:12.
Installation(HVHZ): Installed with 5-1/8 inch exposure,in accordance with RAS
115 and manufacturer's published;installation instructions.
Shingles shall be attached using;;6 Nail Pattern" detailed
below.
Installation (Non-HVHZ): Installed with 5-1/8-inch exposure lin accordance with FBC
requirements and man 6 facture�'s published installation
instructions. Shingles shall be atfached using either"4 Nail
Pattern"or T Nail Pattern"detailed below.
ji
I
Mailing
X718
Area.. . ,. .�.. . .,.. ...
fte
Figure 1. Elite Glass-Seal&Glass-Seal
4 Nail Pattern (Non-HVHZ only)
,I
I I
I
MAILS
Nailing
Alyea - -_..__.-- -----..._ ---- --------- --� ------- --- L , �
5- 18'x:
. ,Butt<Edge' i I
Figure 2. Elite Glass-Seal&Glass-Seal j
6 Nail Pattern
I I
i TBP15001.4 FL18355-R4 l Page 3 of 11
This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the duration;for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not
specifically addressed herein. id
j
i
i I
CREEi� TAMKO BUILDING PRODUCTS
K Asphalt Shingles
I � I
TECHNICAL SERVICES,LLC
i
Heritage@ Basic Wind Speed(Vuit): Max. 194 mph
(Dallas, Frederick,Joplin, Basic Wind Speed(Vasd): Max. 150 mph
Phillipsburg&Tuscaloosa) Deck(HVHZ): In accordance with FBC r equirernents;
& Solidly sheathed min. 19/32 in. plywood for wood plank for
Heritage@ Premium new construction; Min 15/32 in. plywood existing
(Dallas, Frederick construction.
Phillipsburg&Tuscaloosa) Deck(Non-HVHZ): In accordance with FBC requirements;
& Solidly sheathed min. 15%32 in, plywoodlor wood plank for
Heritage@ Woodgate new construction;Min. 7/16 in.OSB existing construction.
(Dallas&Frederick) Underlayment: In accordance with FBC requirements.
Min.slope: 2:12 and in accordance with FBC!requirements. Refer to
the manufacturer's application instructions when installing
shingles at slopes greater than 21:12.
Installation(HVHZ): Installed with 5-5/8 in. exposure in accordance with RAS
115 and manufacturer's,publishedinstallation instructions.
Shingles shall be attached using ,"6 Nail Pattern" detailed
below.
Installation (Non-HVHZ): Installed with 5-5/8 in. exposure in accordance with FBC
requirements and manufacturer's published installation
instructions. Shingles shall be attached using either'A Nail
Pattern"or"6 Nail Pattern"detailed below.
I
l
I .
FASTENERS
N
AIL ZONE,:
`<COMMON
BOND:
EXPOSU'IE
�'r -- 12.12"—► -- 12=3I$" --1 ± =n`1.2
I i
Figure 3. Heritage@, Heritage@ Premium,and Heritage@ Woodgate(Dallas)
4 Nail Pattern (non-HVHZ only)
FASTENERSr` NAIL TONE
COMMQPl.
I;B N
O D'
I ,
561'/S"
EXPQSURE 5 5I8°`
�
1—� }t-7=112-►�7 f/2 -�►�1-1-3/8'-�-7'ice:-►�-7,='1I2"-� I1-1`1 i
Figure 4. Heritage@&Heritage@ Premium
6 Nail Pattern
i
i
I '
I i
TBP15001.4 FL18355-R4 j Page 4 of 11
This evaluation report is provided for State of Florida product approval under Rule 61G20-3.;The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the duration Ifor which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other:product attributes that are not
specifically addressed herein.
i
, I
I
I
j
i
����� TAMKO BUILDING PRODUCTS
j j I Asphalt Shingles
TECHNICAL SERVICES,LLC I
it
SCENIS p
�!COMNt N BAND
i ..
I
. f,.• EXPgSU�ES�lB ' � i
A l• 1 Y
I
Figure 5. Heritage®Woodgate
6 Nail Pattern
i 12-112"- w' i --12=1Y2"`
FASTENERS
i s � j
«.
to o
N
Figure 6. Heritage®, Heritage®Premium, &Heritage®Wood!gate
Alternate 6 Nail Pattern
� I
x I
I
IVAILzONE
a.
MXP SURE
j Dq.NOT FASTEN'
ALONG ED�"� �0 i
$ A� g,< C�dIUIMON BONG£
i
z � �
x ppR6FERFl~
�1:�5,CATfkON ' �
Figure 7. Heritage®(Tuscaloosa)
Expanded Nail Zone
Nail patterns from Figures 3,4,and 6 may be placed in the nail zone as described above
I
TBP15001.4 FL18355-R4 i' Page 5 of 11
j This evaluation report is provided for State of Florida product approval under Rule 61G20-3.I The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the durationlfor which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not
specifically addressed herein.
i
I
I '
I i
� I
TAMKO BUILDING PRODUCTS
SCREEK l i Asphalt Shingles
TECHNICAL;SERVICES,LLC I j
{ I I
Heritage®Premium Basic Wind Speed(Vuit): Max. 194 mph
(Frederick) Basic Wind Speed(Vasa): Max. 150 mph
Deck(HVHZ): In accordance with FBC requirements;
Solidly sheathed min. 19/32 in. plywood or wood plank for
new construction; Min'l 15/32 1 in. plywood existing
construction. I
Deck(Non-HVHZ): In accordance with FBC requirements;
Solidly sheathed min. 15%32 in. plywood�or wood plank for
new construction; Min.7/16 in. OSB existing construction.
Underlayment: In accordance with FBC requirements.
Min.slope: 2:12 and in accordance with FBC;requirements. Refer to
the manufacturer's application instructio s when installing
shingles at slopes greater,than 21':12. .
Installation(HVHZ): Installed with 5 in. exposure in accordance with RAS 115
and manufacturer's published j installation instructions.
Shingles shall be attached using ';6 Naii Pattern" detailed
below.
Installation (Non-HVHZ): Installed with 5 in. exposure in accordance with FBC
requirements and manufacture''''s published installation
instructions. Shingles shall be attached using either"4 Nail
Pattern"or T Nail Pattern"detailed below.
I I
' II
"FAS.TEMERS �t7Mmo- BQI U
r � I
Ei(I?i'JSIJRE'S"
1' ii"> 12•• ���t � ' I �
Figure 8. Heritage®Premium(Frederick) i
4 Nail Pattern (non-HVHZ only)
`NAIL ZONEI I .
FASINEIS ;('AC1N'16(IND
r
EXPOSURE "
Figure 9. Heritage®Premium (Frederick) '
6 Nail Pattern i
I
I •
i .
i I
i TBP15001.4 FL18355-R4 ( Page 6 of 11
This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the durationifor which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or otherlp�oduct attributes that are not
specifically addressed herein. I I
li I
I
1
TAMKO BUILDING PRODUCTS
ACKEEK
I Asphalt Shingles
TECHNICAL SERVICES,LLC
jl
Heritage®Woodgate Basic Wind Speed(Wit): Max. 194 mph
(Frederick) Basic Wind Speed(Vasa): Max. 150 mph
Deck(Non-HVHZ): In accordance with FBC requirements;
Solidly sheathed min. 15/32 in. plywood or wood plank for
new construction; Min.7/16 in. OSB':existing construction.
Underlayment: In accordance with FBC requirements. I
Min.slope: 2:12 and in accordance with FBC,�equirements. Refer to
the manufacturer's application instructionls when installing
shingles at slopes greater than 21:12.
Installation (Non-HVHZ): Installed with 5 in. exposure in';accordance with FBC
requirements and manufacturer'si published installation
instructions. Shingles shall be attached using either"4 Nail
Pattern"or"6 Nail Pattern"detailed below!
�'I I
' I
N `1UZONED
COMMON BOND-;
I
I
i I
Y i i
�!-'1 �` 'ii • �12-318"--�- `li��: ,,,,a �1�� � ; I
Figure 10. Heritage®Woodgate(Frederick)
4 Nail Pattern (non-HVHZ only)
NAIIZONEt
_ MN
r.
I:..
r
i
�•1�'"` � EItPDSURES"
1° •8;1�2��;:�►�'��9=318'.x-�►�#3'?R�F`9�1/2'fP.� �-1•"' �,i I
Figure 11. Heritage®Woodgate(Frederick) j
6 Nail Pattern
i I
I jl i
I Ii� I
I
' I
� I
TBP15001.4 FL18355-R4 j Page 7 of 11
I This evaluation report is provided for State of Florida product approval under Rule 61G20-31 The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use or other product'attributes that are not
specifically addressed herein.
I I
i I
I I
I