The URL can be used to link to this page

Home My WebLink AboutProduct Approval (2) FILECOEXTERIOR RESEARCH& DESIGN,LLC. Certificate of Authorization#9503 QO �f RINITY Ef�� 353 CHRISTIAN STREET,UNIT OXFORD,CT 06478478 ECEIVED PHONE:(203)262-9245 D FAX:(203)262-9243 EVALUATION REPORT Owens Corning FEB t 4 ?018 Evaluation Report 037940.02.12-R7 One Owens Corning Parkway F1.10674-1112 Toledo,OH 43659 ST• Lucie County, Permitting Date of Issuance:02/06/2012 Revision 7: 04/18/2016 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 51h Edition (2014) Florida Building Code sections noted herein. DESCRIPTION: Owens Corning Asphalt Roof Shingles LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 8. Prepared by: °:pro-s„•ss” '*"_ "' 'P'•.=Q?t�,,.•T ,•' The facsimile seal appearing was authorized by Robert Nieminen, Robert J.M.Nieminen,P.E. Y'%%r'�OUat��p4 P.E.on 04/18/2016.This does not serve as an electronically signed Florida Registration No.59166,Florida DC4 ANE1983 ✓ """t""ss document.Signed,sealed hardcopies have been transmitted to the Product Approval Administrator and to the named client CERTIFICATION OF INDEPENDENCE: 1. Trinity lERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Trinity ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither TrinitylERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report,or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. • r- TRINITY ERS ROOFING SYSTEMS EVALUATION: 1. SCOPE: Product Category: Roofing Sub-Category: Asphalt Shingles Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated compliance with the following sections of the Florida Building Code and Florida Building Code, Residential Volume through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations/Conditions of Use set forth herein. 2. STANDARDS: Section Property Standard Year 1507.2.5,R905.2.4 Physical Properties ASTM D3462 2009 1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2009 1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2008 3. REFERENCES: Enti Examination Reference Date UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007 UL LLC(CER9626) Physicals&Wind Resistance 20120516-112453 05/16/2012 UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006 UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012 UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014 UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014 UL LLC(TST9628) Physical Properties Classification letter 02/13/2014 UL LLC(TST9628) Physical Properties Classification letter 10/02/2015 Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various UL LLC (QUA9625) Quality Control Service Confirmation,R2453 Exp.08/20/2017 4. PRODUCT DESCRIPTION: 4.1 Asphalt Shingles: 4.1.1 Classic and Supreme'are fiberglass reinforced,3-tab asphalt roof shingles. 4.1.2 Berkshire*are fiberglass reinforced,4-tab asphalt roof shingles. 4.1.3 Devonshire'" are fiberglass reinforced,5-tab asphalt roof shingles. 4.1.4 Durations, TruDefinition* Durations, Duration* Premium Cool, TruDefinition' Duration* Designer Color Collection, TruDefinition®Oakridge, Oakridge® and WeatherGuard' HP are fiberglass reinforced, laminated asphalt roof shingles. 4.2 Berkshire" Hip & Ridge Shingles, High Ridge, WeatherGuard® HP Hip & Ridge Shingles, ProEdge Hip & Ridge Shingles and DuraRidge'" Hip&Ridge Shingles are fiberglass reinforced, hip and ridge asphalt roof shingles. 4.3 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles. 5. LIMITATIONS: 5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report,or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in the HVHZ. 5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire ratings of this product. Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization 119503 FL10674-1112 Revision 7:04/18/2016 Page 2 of 8 TRINITY 'ERD 5.4 Wind Classification: 5.4.1 All Owens Corning shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for use in all wind zones up to Vasd= 150 mph (V,it= 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.2 All Owens Corning hip&ridge shingles,Starter Strip Shingle and Starter Strip Plus noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161,Class F, indicating the shingles are acceptable for use in all wind zones up to Vasd = 150 mph (Vnit= 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.3 Classification by ASTM D7158 applies to exposure category B or C and a building height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. 5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations. 5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building Code and F.A.C. Rule 61G20-3. 6. INSTALLATION: 6.1 Underlayment: 6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product Approval,or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3. 6.2 Asphalt Shingles: 6.2.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using minimum four (4) nails per shingle in accordance with FBC Sections 1507.2 or R905.2, with the following exceptions: Berkshire®shingles require minimum five(5)nails per shingle. ➢ WeatherGuarde HP shingles require minimum six(6)nails per shingle. ➢ Devonshiret"'shingles require minimum six(6)nails per shingle. Y Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip. Refer to Owens Corning published information on wind resistance and installation limitations. 6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required. See figures below for details. 6.2.5 Minimum Nailing–Starter Strip Shingle and Starter Strip Plus: Felt underlayment Deck Felt underleyment r Deck SaM+dhered _ WowtherLoi Sell-adhered J u^dadaymet WeatherLocke underlayment = Drip edge Drip edge Drip— edge Naffs located Nails located 2'-3'from eave Y-3'from eave Install first Self-sealing adhesive Sa f�eealing adhesive Starter Strip positioned along eave ��6rre oveeder Snip pWs positioned along eave shingle with \ 6"removed Starter ngs eaves and rakes r. Starter Strip overhangs eaves and rakes 1/0"-3/4" Strip shitgk overhaH-'/: ip Plu Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization#9503 FL10674-R12 Revision 7:04/18/2016 Page 3 of 8 (Tt�INITY ERS 6.2.6 Minimum Nailing—Classic®&Supreme: Normal Mansard or Area pare Normal Mansard or Area pin Wind Arose High Wind desvanes y Wind Are" High Wind desveares y Area para vientos normsies Areas vientos fuertes Ares para Want"normal" Areas vieertos fuartes r TAI r r z' IB z' r T !A) r t• z" tr tt• •�I 5"Exposure 5 BIB"Exposwa Exposition Exposk;& 6.2.7 Minimum Nailing—Berkshire®: Sealant strip Sealant strip La lira de seHada La dra de wHador 0-0 t81h• 9 Yf 9 Vf 8 Vf t "8 Vt" 81h" 8 ui" 8 r r Standard Fastening Pattern 6-Nail Fastening Pattern Sealant strip La Vra de sellador IN • 04----------0-• 04----------+•4---►• "8 Y?' 8 V;" 8 Yf 8 Vt• t t.. 1 2 Asphalt rooting cement Cemento de techo de astatto Mansard or Steep Slope Fastening Pattern Exterior Research and Design,U.C. Evaluation Report 037940.02.12-117 Certificate of Authorization#9503 F1.10674-1112 Revision 7:04/18/2016 Page 4 of 8 TRINITY ERS 6.2.8 Minimum Nailing—Devonshire TM I r l 2„ i 8„ I 8., I B. I 7- I _� N h. paws � AWIs .._... r 5.518"exposure Sealant location Exposiei6n de 5.5/8 pulp Ubicaci6n del selladix sw• e Ten 1"Spots of As haft Roof Cement Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern 6.2.9 Minimum Nailing—Duration®,TruDefinition® Duration, Duration® Premium Cool &TruDefinition� Duration• Designer Color Collection: 4-Nall Fastening Pattern 6-Nall Fastening Pattern SIMMONS fas»I•ng aw rlola Sta•NWae IMStffffeg ar•a W kh Nal4 lvWral W TVPIM r 12^ tr r + fr 1r 1^ �e�>.`•r.� • n..p a.w lww • .w.s Eaw."-""""'s...___��. __. +moo •ow.r++•�I+,• sto-s•aro^ sin^san- Standard Fastening Pattern 6-Nail Fastening Pattern Fastening for Slopes Greater Than 21:12 S."I ?o f-WIN—rrldth N.I.Typ ul IrFIsfn•ssn^ Four 7•Spon of AspMN•wMq Cunsm Mansard or Steep Slope Fastening Pattern Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-117 Certificate ojAuthori:odon#9503 FL10674-R12 Revision 7:04/18/2016 Page 5 of 8 TRINITY ERS 6.2.1 Minimum Nailing–Tru Definition'Oakridge®,Oakridge®: 4 Nail Pattern 6 Nail Pattern Esquema con 4 clavos Eu Mersa con 6 clavus 1" r 1 r ir Ir 66/8"ExposureNags 5518 Exposuw Nails Exposidondo56/8pufg. Claws Exposid6ndo56/8pulg. 5StrExposure, Clercs 65/8"Exposuw Exposid6n de 66/9 pu(g. Exposidvn de 65/8 puig. Standard Fastening Pattern 6-Nail Fastening Pattern Fastening for Slopes Greater Than 21:12 S—N•IN f.--g Nell.Typlul 1' 12' e-1n• ssro- 0 Four 1-SpM o1 AWiad1 ftOO"Ca—o1 Mansard or Steep Slope Fastening Pattern 6.2.1 Minimum Nailing—WeatherGuardo HP: 1• �' t ViM�rdNew k— _• 'moi •'� :ti;�Q+ :f lrlwwr7iww�Nil{iN 6iuwwi4Nrri+diw Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization#9503 F1-10674-1112 Revision 7:04/18/2016 Page 6 of 8 TRINITY ERD 6.3 Hip&Ridge Shingles: 6.3.1 Installation of Berkshire* Hip and Ridge Shingles, High Ridge, WeatherGuard' HP Hip and Ridge Shingles and ProEdge Hip&Ridge Shingles shall comply with the manufacturer's current published instructions, using four (4) nails per shingle. Installation of DuraRidge'" Hip & Ridge Shingles shall comply with the manufacturer's current published instructions, using two (2) nails per shingle. Refer to Owens Corning published information on wind resistance and installation limitations, including the use of hand-sealing for wind warranties. 6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.3.3 Minimum Nailing—Berkshire®Hip&Ridge and High Ridge: Fig.1 4 Fig.2 P�rlx�rllr DYeaioN p TopVlew 9doNON Nato A Nato Nail; r I I Top lanYlalad Plop I I A I 1 r 4 1 I I 1 I I I I p I I 1 I I 1 I 1 1 I p 1 I I I 41 .jr + .1' ♦ I r P I 1 1 I I I 6.3.4 Minimum Nailing—WeatherGuard®HP Hip and Ridge: Fig.C Hip&Ridge Shingle Fastening Fig.A Y q TopVlew Prevalling Whd DlnMbn —� A Nails A i i Kalb WIY I 7• Z. 1- A I I I A �� I 1 6• E[pOa11N1 11 �7 Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R7 Certificate of Authorization#9503 FL10674-R12 Revision 7:04/18/2016 Page 7 of 8 i TRINITY ERS 6.3.5 Minimum Nailing-ProEdge Hip&Ridge Shingles: Prevailing Standard 11. Wind Direction Fastening Sealant Strip Pattern 6'Exposure r-� 12' I Sealant Fasten 71h' 7h• 8'Expewre Cover Exposed Fasteners with Reef Content I`�72•_—tel 6.3.6 Minimum Nailing—DuraRidge'" Hip&Ridge Shingles: Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer to Owens Corning published installation instructions for their minimum requirements. r—Pnraifn,Wird Dintean Top en— Direaien dhent•di rant Vkta t'VMn I- Dincoon da*l dant•pradonxranu I .t. q'w • Own•Carting SuraNai' • �" Naib�� l Oar•• 1 I • 1 1 �_ IVg — 12-- 7. LABELING: 7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. 7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC Table 1507.2.7.1/R905.2.6.1. 8. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 9. MANUFACTURING PLANTS: Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA requirements. 10. QUALITY ASSURANCE ENTITY: UL LLC—QUA9625;(414)248-6409;karen.buchmann@ul.com - END OF EVALUATION REPORT- Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R7 Certificate of Authorization#9503 FL10674-R12 Revision 7:04/18/2016 Page 8 of 8