HomeMy WebLinkAboutProduct Approval I.
i
' I
EXTERIOR RESEARCH&DESIGN,LLC.
Certificate of Authorization#9503
TRINITY
1 353 CHRISTIAN STREET, UNIT
QO �ERD I' OXFORD,CT 06478478
;(203)262-9245
EVALUATION REPORT I
Owens Corning i Evaluation Report 037940.02.12-R8
One Owe'hs Corning Parkway FL10674-1113
Toledo,OH 43659 Date,of Issuance:02/06/2012
(740)404-7829Revision 8: 10/09/2017
SCOPE: I
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida:The documentation submitted has been 'reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 6th !Edition (2017) Florida Building Code
sections noted herein.
jDESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Qufality Assurance Agency noted
herein and FBC 1507.2.7.1/R905.2.6.1.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as: the named products) changes, the
.referenced Quality Assurance documentation changes, or provisions of the Code that�relate�to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. Trinity)ERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.!
ADVERTISEMENT: The Evaluation Report number preceded by the words "TrinitylERD Evaluated" may be displayed in
advertising literature. -If any portion of the Evaluation Report is displayed,then it shall b€e done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user!by the manufacturer or
its distributors and shall be available for inspection at the job site at the request,of the Building Official.
This Evaluation Report consists of pages 1 through 8.
Prepared by:
RobertJ.M.Nieminen P.E. �r'�F0 Thefacsimilesealappearingwas authorized b Robert
+ t +J�haii�''�,k Nieminen,P.E.on 30/09/2 17.This does not serve as an
Florida Registration No.59165,Florida DCA ANE1983 q
electronically signed document.
CERTIFICATION OF INDEPENDENCE: P, i
1. Trinityl ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates. I 1
2. Trinity ERD is not owned,operated or controlled by any company manufacturing or distributing p'roductsit evaluates.
3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen,P.E.does not have;nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This'is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any sway,the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained
specifically for that purpose. ,
f
I
I
I I
I, I
II '�
V
TRINITY I ERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated
compliance with the following sections of the 6th Edition (2017) Florida Building Code and Florida Building Code,
Residential Volume through testing in accordance with the following Standards. Compliance is subject to the
Installation Requirements and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1507.2.5,R905.2.4 Physical Properties ASTM D3462 2010
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2016
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2011
3. REFERENCES:
Entity Examination Reference Date
UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007
UL LLC(CER9626) Physicals&Wind Resistance 20120516-R2453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various
UL LLC (QUA9625) Quality Control Service Confirmation Exp.05/16/2020
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Classic'and Supreme'are fiberglass reinforced,3-tab asphalt roof shingles.
4.1.2 Berkshire'are fiberglass reinforced,4-tab asphalt roof shingles.
4.1.3 DevonshireT"are fiberglass reinforced,5-tab asphalt roof shingles.
4.1.4 Duration', TruDefinition' Duration', Duration' Premium Cool, TruDefinition' Duration' Designer Color
Collection, TruDefinition'Oakridge', Oakridge® and WeatherGuard' HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.2 Hip&Ridge Shingles:
4.2.1 Berkshire' Hip & Ridge Shingles, High Ridge, WeatherGuard' HP Hip & Ridge Shingles, ProEdge Hip & Ridge
Shingles and DuraRidgell Hip&Ridge Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles.
4.3 Accessory Starter Strips:
4.3.1 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither Trinity)ERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof,is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory
for fire ratings of this product.
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-1113
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 2 of 8
h
� I
,
RIWry I ERD
5_4 Wind Classification:
5.4.1 All Owens Corning asphalt shingles,noted herein are Classified in accordance with FBC'Tables 1507.2.7.1
and R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158,Class H, indicating the shingles are acceptable
for use in all wind zones up to Vasd = 150 mph (V„it = 194 mph). Refer to �ection 6 for installation
requirements to meet this wind rating.
5:4.2 All Owens Corning hip & ridge shingles, Starter'Strip Shingle and Starter Strip Plus noted herein are
Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1;to ASTM D3161, Class F, indicating the
shingles are acceptable for use in all wind zones up to Vasd= 150 mpl (Vul,=Q94 mph). Refer to Section 6 for
installation requirements to meet this wind rating. j
5.4.3 Classification by ASTM D7158 applies to exposure category B or C, ,as defined in FBC 1609.4.3, and a mean
roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions
outside these limitations. Contact the shingle manufacturer-for data'specifi c to eaA shingle.
5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations.
I; I
5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C.Rule 61G20-3.
I
6. INSTALLATION:
I
6_1 Underlayment: r'
6.1.1 Underlayment shall be acceptable to Owens Corning and shall Bold current Florida Statewide Product
Approval,or be Locally Approved per Rule 61G20-3,per FBC 1507.2.3,1507�2.4 or R905.2.3.
6_2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the Owens Corning curme,)t published instructions, using
minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R9051.2.6, with the following
exceptions: e
Berkshire shingles require minimum five(5) nails per shingle.
i WeatheeGuarde HP shingles require minimum six(6)nails per shingle. ;
DevonshireT"'shingles require minimum six(6)nails per shingle'
i Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip.
I,
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special i ethods of fastening are
required. See figures below for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
I 'I
I
Felt undedayment Deck Feltunderlayinent Deck Selftidhered
Weatherl ock'a
Self-adhered I l undedayment
WeatherLocke'
underlayment
� Drip edge
i
Uaigpe Drip edge DDnpe
Nags looted
Nails located 2—3 from save
2'-3"from eave a,• '
i
Install firstSelf-sealing adhesiveInstalrstStarter Salkealing adhesive
Starter Si.*p .••- positioned along eave vgith 6'rremoved
6'removStrip Pius I positioned along eave
shingle with
ed \ Sb I S 'mP"os a% eaves and rakes 7/4'-3/4'
Starter Strip shingle overhangs eaves and rakes/r=3i"
t
Exterior Research and Design,LLC. rl Evaluation Report 037940.02.12-118
Certificate of Authorization#9503 6r"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 3 of 8
I ,
I I;
TRINITY,ERD
6.2.6 Minimum Nailing—Classic®&Supreme:
Normal Mansard or Area para Normal Mansard or Area para
Wind Areas High Wind dsvin•s y Wind Areas High Wind desvanes y
Am¶ vientos normales Areas vierrtos fu&rtes Area pare vientos normal*& Areas vientos fuertas
ua ttt
5"Exposure 5 518,Exposure
Expo&ic:Mn
ExposlaM
6.2.7 Minimum Nailing—Berkshire®:
Sealantstrip Sealant strip
La fira da secador Le tLa de sellador
8 Yz' 9 Yf 9 Yf 8 trf '
)04, •814" 814• a Yi" aLILL
�• �•J 1 p .J
r
r
1
Standard Fastening Pattern 6-Nail Fastening Pattern
Sealant strip
La tka de sallador
t,8Yf 8Yf a Yf a Yf
r
r
2' Asphalt roofing cement
Camento de recho de astaflo
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-118
Certificate of Authorization tl9503 6T"EDITION(2017)FBC NON-HVH2 EVALUATION FL10674-R13
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 4 of 8
I
I
i
f TRINITY I ERD
6.2.8 Minimum Nailing–Devonshire'rm:
r
I'
I '
1" 7" { 8"- , 8" I--8-1---H 1" j111 f'
4T;
a77as i, d
s; Nail's
5-518'exposureSealant location " E
6tposiclb de 5.5/8 pulg Ubicadk del sellador �,,• _ I, l"
by
Ten t"Spots of ke haft Roof Cement
Standard 6-Nail Fastening Pattern Mansa M or Steep Slope�Fastening Pattern
6.2.9 Minimum Nailing – Duration®, Tru Definition° Duration, Duration® Premium, Cool & TruDefinitlon®
Duration®Designer Color Collection: ;
I
4-Nail Fastening Pattern I il 6-Nail Fastening Pattern
Sb•.N.Wastmng ar.a Width 'sur.nalm tawning.wlmh
tta7.lypieai tWLryW-1
es-.»ean:,u.w.r._.uva-.s:.-- �om-ru ;..:ate. ..,:.,..r <:•...; ww. ,ry .M<:: ..,o*;,- .•s:• �-o...x. ,>-•s
Standard Fastening Pattern 6-NailF6steninlg Pattern
Fastening for Slopes Greater Than 21:12 I
611nNtlW b.bn4p 6N WQID '
N.4 TYp�-W
I
t• tr tr I
T�: mnfw�w •+✓- � wa`• nom• I
'T-sem. .t^'Pt
I
F—t`spW—(MplWt nnallrp
Mansard or Steep Slope Fastening Pattern
' ' d
I
I
'
i• �
I
Exterior Research and Design,LLC. I Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6r"EDITION(2017)FBC NON-HVHZ EVALUATION �' FL10674-1113
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 5 of 8
I�
i
'\�TRJN1TYjERD
6.2.1 Minimum Nailing—TruDefinitiono Oakiridge",OakridgeO:
4 Nail Paltsm 6 Nail Pattani
BWOMa CM 4 CIMS Eslquema con 6 davos
ir
5 518"
Exposure 6518" M Nails
5 Nags 5 Sir FxPMM 5 51ir Exposure
ES ,i d. slspuiq. clavas Egaildtin de 5 SIC pdq. Claws Exposid6n 6 618Ptdg.
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slopes Greater Than 21:12
K.B.
It,
Foul
641r.5.5V
V Spoft 01 Mphaft Kbonng C-1
Mansard or Steep Slope Fastening Pattern
6.2.1 Minimum Nailing—WeatherGuardO HP:
SWIF10 side V1WW
4—
LkW
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-118
Certificate of Authorization#9503 EDITION(2017)FBC NON-HVHZ EVALUATION FI-10674-1113
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 6 of 8
i
TRINI7`Y I ERD
6,=3 Hip&Ridge Shingles: I
6.3.1 Installation of Berkshire Hip,arid;Ridge Shingles, High Ridge, WeatherGuatd® HPC Hip and Ridge Shingles
and ProEdge.Hip & Ridge Shingles shall comply with the Owens Corning,icurrent published instructions,
using four (4) nails per shingle. Installation of DuraRidgeT"I Hip & RidgeShingles shall comply with the
Owens Corning current published instructions, using two (2) nailsjper shingle. Refer to Owens Corning
t published information on wind resistance and installation limitations, Incluil'ing the use of hand-sealing for
.� wind warranties.
6.3.2 Fasteners shall-be in accordance with the manufacturer's publishe3d requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berkshire"Hip&Ridge and High Ridge:
Flg,'1 Fig.2
a
F_— PnYailatp Wnd '
DirectionA IToI'vler .E Sideviaw
' ll t- TnP paninated � rT'
A 3'1 1 ace
I
I I 1 I
A 1 1 !
I i i
'til
t'
1 E'
1
63.4 Minimum Nailing—WeatherGuard®HP Hip and Ridge:
Fi .A v 4 Fig.C Hip&Ridge Shingle Faatening
g 11%, WkW � ToliVinl�
F—Dlroel A I F• pp
A
Nabs__'--..--.—•.--.� q � �: ;�„
A i I I
Nails Na Rs
A i i r' i II
IV,
G
i k
Exterior Research and Design,LLC, i. Evaluation Report 037940.02.12-R8
Certificate ofAuthorization#9503 6T"EDITION(2017)FBC NOWHVHZ EVALUATION ( F1.10674-1113
Owens Corning Asphalt Roof Shingles c Revision 8:10/09/2017
Page 7 of 9
TRINITY J ERD
6.3.5 Minimum Nailing-ProEdge Hip&Ridge Shingles:
Prevailing Fastening
.--71'—►
Wind Strip nd Direction Fastening
pmrePattern
tt
'Exposure I rw
t,
y., 12• Se«tam
Fasten 71h' 71h' 6'
-, Covsr Exposed 'f l
Fasteners with
Rcaf Cee:eat
6.3.6 Minimum Nailing–DuraRidgel Hip&Ridge Shingles:
Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer to Owens Corning
published installation instructions for their minimum requirements.
_Proniing Wird anto don ve en�ptan
Dirvaiondrxnimnwdurmt I- Vfsraeuperlor
ew
Dirombn dol tiontn Pradrxnironto
f�
NO
} z i t a �,OuvcntCormngSurelyal'����y Gmo
A I I ly
r 4 l v r Ule$
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table.1507.2.7.1/R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC–QUA9625;(631)546-2458;Kanchi.Agrawala-Dokania@ul.com
END OF EVALUATION REPORT-.
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-118
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-1113
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 8 of 8