HomeMy WebLinkAboutProduct Approval Ml I`9iM1 MIAMI-DADE COUNTY
0
VOA j PRODUCT CONTROL SECTION
11805 SW 26 Street,Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) Miami,Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISIONT(786)315-2590 F(786)31525-99
NOTICE OF ACCEPTANCE (NOA) RECEIVED www.miamidade.gov/economy
Interwrap,Inc. MAR 2 3 202
32923 Mission Way
Mission,BC,Canada V2V-6E4 ST. Lucie County, Permittina
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control
Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to
have this product or material tested for quality assurance purposes. If this product or material fails to perform in
the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately
revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to
revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or
material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Titanium®UDL-25 PLUS,Titanium®UDL-30,Titanium®UDL-50,UDL TT,UDL TF,
UDL TTMC-300,RhinoRoof U10,RhinoRoof U15,RhinoRoof U20,Titanium UDL25,and
RhinoRoof RSA Synthetic Underlayments
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city,state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
,,;: A VERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
�+' expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it shall be done
ii its entirety.
SPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
Ulan be available for inspection at the job site at the request of the Building Official.
his NOA renews and revises NOA No. 13-0610.01 and consists of pages 1 through 5.
he submitted documentation was reviewed by Alex Tigera.
ezentzi
NOA No.: 14-0603.18
MIAMI•DADE COUNTY
APPROVED Expiration Date: 08/08/18
Approval Date: 06/11/15
Page 1 of 5
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub-Category: Underlayment
Material: Polypropylene
SCOPE:
This acceptance is for Titanium®UDL-25 PLUS,Titanium®UDL-30,Titanium®UDL-50,UDL TT,UDL TF,
UDL TTMC-300,RhinoRoof U10,RhinoRoof U15,RhinoRoof U20,Titanium UDL25,and RhinoRoof RSA
Synthetic Underlayments as described in this Notice of Acceptance,for use with approved prepared roof assemblies
where ASTM D226 Type underlayment is specified and installed with prescribed approved fasteners and fastener
densities.Designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the
Florida Building Code
PRODUCT DESCRIPTION:
Test Product
Product Dimensions Specification Description
Titanium®UDL-25 PLUS 48"x 250' rolls ASTM D226 Woven synthetic polymer underlayment with one
Manufacturing Type I&II side coated with UV protected and slip resistant
Location#1  polymer stabilized polypropylene on both sides.
Titanium®UDL-30 48"x 250' rolls ASTM D226 Woven synthetic polymer underlayment with two
Manufacturing Type I&II sides coated with UV protected and slip resistant
Location#1 polymer stabilized polypropylene on both sides.
Titanium®UDL-50. 48"x 250' rolls ASTM D226 Woven synthetic polymer underlayment with two
Manufacturing Type I&II sides coated with UV protected and slip resistant
Location#1 polymer stabilized polypropylene on both sides.
UDL TT 48"x 250' rolls ASTM D226 Woven synthetic polymer underlayment with one
Manufacturing Type I&II side coated with UV protected and slip resistant
Location#1 polymer stabilized polypropylene on both sides.
UDL TF 48"x 250' rolls ASTM D226 Woven synthetic polymer underlayment with two
Manufacturing Type I&II sides coated with UV protected and slip resistant
Location#1 polymer stabilized polypropylene on both sides.
UDL TTMC-300 48"x 250' rolls ASTM D226 Woven synthetic polymer underlayment with two
Manufacturing Type I&II sides coated with UV protected and slip resistant
Location#2 polymer stabilized polypropylene on both sides.
RhinoRoof U10 42"x 286' rolls ASTM D226 Woven synthetic polymer underlayment with two
Manufacturing Type I&II sides coated with UV protected and slip resistant
Location #3 polymer stabilized polypropylene on both sides.
NOA No.: 14-0603.18
MIAMI.DADE COUNTY
APPROVED Expiration Date: 08/08/18
Approval Date: 06/11/15
Page 2 of 5
RhinoRoof U15 42"x 286' rolls ASTM D226 Woven synthetic polymer underlayment with two
Manufacturing Type I and II sides coated with UV protected and slip resistant
Location #3 polymer stabilized polypropylene on both sides.
RhinoRoof U20 42"x 286' rolls ASTM D226 Woven synthetic polymer underlayment with two
Manufacturing Location #3 Type I and II sides coated with UV protected and slip resistant
polymer stabilized polypropylene on both sides.
Titanium UDL25 48"x 250' rolls ASTM D226 Woven synthetic polymer underlayment with two
Manufacturing Location #3 Type I and II sides coated with UV protected and slip resistant
polymer stabilized polypropylene on both sides.
RhinoRoof RSA 36"x 67' rolls ASTM D1970 Unreinforced polymer modified bitumen material
Manufacturing Location #4 adhered to the underside of a polymer-coated,
synthetic woven sheet. The underside is backed
with a release film.
MANUFACTURING LOCATIONS:
1. ML1
2. ML2
3. ML3
4. ML4
EVIDENCE SUBMITTED:
Test Agency Test Identifier Test Name/Report Date
Intertek Testing Services #3031783 TAS 104 02/19/03
3119607C0Q-003B ICC-ES AC48 02/20/08
3124826-01 ASTM E108 02/19/08
3124826MID-007 ASTM E108 .02/25/08
311801000Q-003 ASTM D226 02/20/08
3130639C0Q-002A ASTM D226 02/20/08
3146738C0Q-003A ASTM D226 06/20/11
3146738C0Q-003B ASTM D 1876/TAS 117 03/28/08
101465036C0Q-001 ASTM D1970 06/27/14
100539395C0Q-006 ASTM D226 06/02/14
101863861C0Q-001A ASTM D226 10/28/14
101823107C0Q-011 ASTM D226 12/09/14
Trinity I ERD 115010.05.10 ASTM D4798/D226 05/14/10
I38010.08.11 ASTM D226 08/11/11
I35520.08.11 ASTM D2523/D1781 08/17/11
NOA No.: 14-0603.18
mukmi•nnne couNnr
APPROVED Expiration Date: 08/08/18
Approval Date: 06/11/15
Page 3 of 5
INSTALLATION SPECIFICATIONS:
Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments
1. Titanium®UDL-25 PLUS,Titanium®UDL-30,Titanium®UDL-50,UDL TTMC-300,UDL TT,UDL TF,
RhinoRoof U10,RhinoRoof U15,RhinoRoof U20,Titanium UDL25,and RhinoRoof RSA Synthetic
Underlayments shall be installed in strict compliance with applicable Building Code.
2. Titanium®UDL-25 PLUS,Titanium®UDL-30,Titanium®UDL-50,UDL TTMC-300,UDL TT,UDL TF,
RhinoRoof U10,RhinoRoof U15,RhinoRoof U20,Titanium UDL25,and RhinoRoof RSA Synthetic
Underlayments shall be installed with a minimum 4-inch head lap in a shingle layer fashion.
3. Titanium®UDL-25 PLUS,Titanium®UDL-30,Titanium®UDL-50,UDL TTMC-300,UDL TT,UDL TF,
RhinoRoof U10,RhinoRoof U15,RhinoRoof U20,and Titanium UDL25 Synthetic Underlayments shall be
fastened with Miami-Dade approved corrosion resistant tin-caps and 12 gauge 1 1/4"annular ring-shank nails,
spaced 6"o.c. at all laps and three staggered rows fastened 12"o.c.in the field of the roll.
4. Titanium®UDL-25 PLUS,Titanium®UDL-30,Titanium®UDL-50,UDL TTMC-300,UDL TT,UDL IF,
RhinoRoof U10,RhinoRoof U15,RhinoRoof U20,Titanium UDL25,and RhinoRoof RSA Synthetic
Underlayments may be used with Asphaltic shingles,Wood shakes and shingles,Non-structural metal roofing,
and quarry slate.Titanium®UDL-30,Titanium®UDL-50,UDLTTMC-300,UDL TT,UDL TF,RhinoRoof
U10,RhinoRoof U15,RhinoRoof U20,Titanium UDL25 and RhinoRoof RSA Synthetic Underlayments shall
not be used as roof tile underlayments.
5. For Roof Tile applications;Titanium®UDL-25 PLUS may be used as an anchor sheet in roof tile applications
when used in combination with a top membrane layer,consisting of a Miami-Dade approved TAS 103 self-
adhering underlayment. (See current NOA listing of approved TAS 103 self-adhering underlayment for
installation guidelines and limitations of use).
6. For fire classification of specific roof assemblies using Titanium® UDL-25 PLUS, Titanium® UDL-30,
Titanium®UDL-50,UDL TTMC-300, UDL TT, UDL TF,RhinoRoof U10, RhinoRoof U15,RhinoRoof U20,
Titanium UDL25, and RhinoRoof RSA Synthetic Underlayments_refer to a current Approved Roofing
Materials Directory for fire ratings of this product.
BUILDING PERMIT REQUIREMENTS:
Application for building permit shall be accompanied by copies of the following:
1. This Notice of Acceptance.
2. Any other documents required by the Building Official or applicable building code in order to properly
evaluate the installation of this material.
NOA No.: 14-0603,18
MANMADE COUNTY
APPROVED Expiration Date: 08/08/18
Approval Date: 06/11/15
Page 4 of 5
LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product.
2. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code.
3. Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall be applied to a smooth, clean and dry surface with deck free of irregularities.All nails in
the deck shall be carefully checked for protruding heads. Re-fasten any loose decking panels. Sweep the deck
thoroughly to remove any dust and debris prior to application.
4. Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall not be hot mopped,refer to manufacturer's published literature for product compatibility.
5. Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall not be applied over an existing roof membrane as a recover system.
6. Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments shall not be left exposed as a temporary roof for longer than 30 days of application.
I 7. UDL_TTMC-300 Synthetic Underlayment shall not be left exposed as a temporary roof for longer than 180
days of application.
8. Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments are components used in roof system assemblies. Roof system assemblies are approved under a
specific Notice of Acceptance. Refer to Prepared Roofing system Product Control Notice of Acceptance for
listed approval of this product with specific prepared roofing products.
9. Titanium® UDL-25 PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF,
RhinoRoof U10, RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic
Underlayments may be used with any approved roof covering Notice of Acceptance listing Titanium®UDL-25
PLUS, Titanium® UDL-30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF, RhinoRoof U10,
RhinoRoof U15, RhinoRoof U20, Titanium UDL25, and RhinoRoof RSA Synthetic Underlayments as a
component part of an assembly in the Notice of Acceptance. If Titanium® UDL-25 PLUS, Titanium®,UDL-
30, Titanium® UDL-50, UDL TTMC-300, UDL TT, UDL TF, RhinoRoof U10, RhinoRoof U15, RhinoRoof
U20, Titanium UDL25, and RhinoRoof RSA Synthetic Underlayments are not listed, a request may be made
to the Authority Having Jurisdiction (AHJ) or the Miami-Dade County Product Control Department for
approval provided that appropriate documentation is provided to detail compatibility of the products, wind
uplift resistance,and fire testing results.
10. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo
and the following statement: "Miami-Dade County Product Control Approved" or the Miami-Dade County
Product Control Seal as shown below.
CUECOUNTY
APPROVED
11. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code
and Rule 61 G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 14-0603,18
MANMADE COUNTY
APPROVED Expiration Date: 08/08/18
Approval Date: 06/11/15
Page 5 of 5
EXTERIOR RESEARCH&DESIGN, LLC.
Certificate of Authorization#9503
353 CHRISTIAN STREET, UNIT#13
TRINITY ER® RECEIVED OXFORD,CT 06478
(203)262-9245
EVALUATION REPORT
Owens Corning
MAR 2 3 £Ii 18 Evaluation Report 037940.02.12-R8
One Owens Corning Parkway FL10674-R13
Toledo,OH 43659 ST. Lucie County, Permitting Date of Issuance:02/06/2012
(740)404-7829 Revision 8: 10/09/2017
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 6th Edition (2017) Florida Building Code
sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein and FBC 1507.2.7.1/R905.2.6.1.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes,'the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. Trinity!ERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity'ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 8.
Prepared by: a31Yo7,,,,
•
Sn
..+•ex-.,
r fi
Robert J.M.Nieminen,P.E. • '1¢ySg,;J`',U�`,,tt; The facsimile seal appearing was authorized by Robert
•" Florida Registration No.59166,Florida DCA ANE1983 ��,,,,,,�s"'' Nieminen,P.E.on 10/09/2017.This does not serve as an
F electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. Trinity'ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
£ r 2. Trinity I ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
$ 3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
imzsj which the evaluation reports are being issued.
4. Robert Nieminen, P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation.. Neither Trinity'ERD nor Robert Nieminen, P.E. are, in any way,the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained
specifically for that purpose.
TRINITY ER®
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles,as produced by Owens Corning,have demonstrated
compliance with the following sections of the 6th Edition (2017) Florida Building Code and Florida Building Code,
Residential Volume through testing in accordance with the following Standards. Compliance is subject to,the
Installation Requirements and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1507.2.5,R905.2.4 Physical Properties ASTM D3462 2010
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2016
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2011
3. REFERENCES:
Entity Examination Reference Date
UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007 '
UL LLC(CER9626) Physicals&Wind Resistance 20120516-R2453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various
UL LLC (QUA9625) Quality Control Service Confirmation Exp.05/16/2020
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Classic and Supreme®are fiberglass reinforced,3-tab asphalt roof shingles.
4.1.2 Berkshire are fiberglass reinforced,4-tab asphalt roof shingles.
4.1.3 Devonshire""are fiberglass reinforced,5-tab asphalt roof shingles.
4.1.4 Duration®, TruDefinition® Duration", Durations Premium Cool, TruDefinition® Duration® Designer Color
Collection, TruDefinition"Oakridge, Oakridge° and WeatherGuard® HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.2 Hip&Ridge Shingles:
4.2.1 Berkshire Hip & Ridge Shingles, High Ridge, WeatherGuard HP Hip& Ridge Shingles, ProEdge Hip & Ridge
Shingles and DuraRidgeT"Hip&Ridge Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles.
4.3 Accessory Starter Strips:
4.3.1 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
5. LIMITATIONS:
5.1 This is a building code evaluation. Neither Trinity'ERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory
for fire ratings of this product.
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6 EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 2 of 8
i
TRINITY ERD
5.4 Wind Classification:
5.4.1 All Owens Corning asphalt shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1
and R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158,Class H, indicating the shingles are acceptable
for use in all wind zones up to Vasd = 150 mph (V„It = 194 mph). Refer to Section 6 for installation
requirements to meet this wind rating.
5.4.2 All Owens Corning hip & ridge shingles, Starter Strip Shingle and Starter Strip Plus noted herein'are
Classified in accordance with FBC Tables 1507.2:7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating}the
shingles are acceptable for use in all wind zones up to Vasd=150 mph(Vu1t=194 mph). Refer to Section 6 for
installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category B or C, as defined in FBC 1609.4.3, and a mean
roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions
outside these limitations. Contact the shingle manufacturer for data specific to each shingle.
5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C.Rule 61G20-3.
6. INSTALLATION:
6_1 Underlayment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 61G20-3,per FBC 1507.2.3,1507.2.4 or R905.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using
minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following
exceptions:
> Berkshire shingles require minimum five(5)nails per shingle.
> WeatherGuard HP shingles require minimum six(6)nails per shingle.
> DevonshireTM shingles require minimum six(6)nails per shingle.
> Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. See figures below for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
r ,
Felt underlayment Deck Felt undertayment �/ Deck Sdfasdhered
leedrlayment
Self-adhered 'w_ underlayment
�✓1j WeatherLocke 'I
l(((am underlayment l(
00
`7� �I� Drip edge
Drip^\\\\
J�-i Drip edge Dr p— e,
edge Wt edge `
O O
Nails located Nags located
-3'from eave
®� 2'-3"from eave
Install first Self-sealing adhesive SeN•sealing adhesive
Starter S . ® positioned aloe eave Instal first Starter Strip Plus ® positioned along cave
shingle \ P g with 6"removed
9 ..
6"removed r Starter StripPius overhangs eaves and rakes 1/4=3/4"'
Starter Strip shingle overhangs eaves and rakes V.1"-ii" 9
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 3 of 8
TRINITY EP
6.2.6 Minimum Nailing—Classic°&Supreme:
gammu
Normal Mansard or Area para Normal Mansard or Area pare
Wind Areas High Wind desvanes y Wind Areas High Wind desvanes y
Area pare vientos normales Areas vientoa fuertes Area pare vientos norrnales Areas vientoa fuertes
IMEAMILIMu ° r - IN
MEM 111111.1111 MEM aninifill
5"Exposure- 5 5/8"Exposure
Exposicidn Exposieidn
6.2.7 Minimum Nailing—Berkshire°:
Sealant strip- Sealant strip
Latin de seUador l La tira de sellador
,— a Yx" s vz" -. g Vf a 81/2" t V S Vz" a,h.. g 1/2" 6 Vz" r
," ,"J ,. J
•
Standard Fastening Pattern 6-Nail Fastening Pattern
Sealant strip
La tira de sellador
&
•t—Vf ser-- aYf e • • 9 V2C a F----►•
a V2'
2" -Asphalt rooting cement
• Cemento de techo de asfalto
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6'"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 4 of 8
CTTRINITY ERD
6.2.8 Minimum Nailing—DevonshireTM':
I I
1,. H 711 I ErlipI g1 I 8" I 711 A • fin
N. '
I . _r 40. 1
�e�
5518°exposure _el =
Exposician de 5.5/8 pulg ine tom` a w.itititi• min 1..
Sealant location
Ubicacibn del sellador �•�, � I I �.
Ten 1"Spots of Asphalt Roof Cement
Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern i
6.2.9 Minimum Nailing — Duration®, TruDefinition® Duration, Duration® Premium Cool & TruDefinition•
Duration®Designer Color Collection:
4-Nail Fastening Pattern 6-Nail Fastening Pattern
SlneNan fastening area width SureNaltS Typicalfastening area width
Nail. Nall,Typlral
12" en ��t2" �I' 12"
-1 [I- 12" It"
C p.rccemysv vae- • s'»"a • o.wca..cS.e • , r1 ` M••[ ....• .-• •TVaa•••• •woor=w s:..rav a
6178^5-618" - \ 1 _
6.178"5.518"
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slopes Greater Than 21:12
SurONelta fastening area Meth I
Neil,Typical
1" 12^ 1r 1"
[ -• •-.pnyeo-r,vr. •-m®s.."c....r.". •
6.1/8"5ncee�.� 1111Uffrile•
I r
�_�
Four 1"Spots of Asphalt Roofing Cement
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6'"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 5 of 8
I
QC
TRINITY EI4D
•
6.2.1 Minimum Nailing—TruDefinition Oakridge®,Oakridge®:
4 Nail Pattern 6 Nail Pattern
Esquema con 4 clavos Esquema con 6 claims
IIIMENEE
1 r
—0. _FE— 12"—54
10:111nEriall
5 5/8 Exposure Nails 5 5/8"Exposure Nails
15 5/8 Csuie 5 5/8"Exposure Exposition de55/Spu14• Claws Expostcr6nde56/8pulg. FxP CLtvos po
Exposieidn de 55/9 pu1g. Expostcidn de 5 6/8;wig.
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slopes Greater Than 21:12
SureNa119 fastening area Width
Ir Rea.Typical
1" 12" 12' r
I IMO . •
c.
)2"
Four 1"Spats of Asphalt Roofing Cement
Mansard or Steep Slope Fastening Pattern
6.2.1 Minimum Nailing—WeatherGuard®HP:
$Inpl.61d01Mw
tict7,112.
IRaty Neil On
1 fT•1••.''fr
Clow erileknow da flldb
•
J
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6 EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 6 of 8
r X
.7 .f
$ a
p O
al al al fT km
a ; w w w w Iw
z a
S W NI—'
o ,
o En
5 o � 3 6 � 5 fist
v -
cc, CIfD Oa m Ro
Ln c
1/1111' / D v / / z mc ^� r3D mlc
O ° 70w =
it-
i
I'~i, f1 A mp �.n N y z z O� y 01 Oq3fDov tv i, N - c ' ti, 3 � �,�a �Df mimr. N Sso '.} N
.s I -0 tDcu
SII mII®fD -0....)ii
133//m IIIf® VI
33 .
CU Ln
j' ; HlE
v < 3 cu d Oo
2 o< Q. 1110 < jFIIJ
C. N N Q 3 30
Do d r, (i, G
o < c
S fp (D -n i0 c et N 00 fL 'rt cm
ID C = I< •
�' '�°� N fD Z 3 O DO S A
N D k----°4 `/I' -1.---)1-1.---)1 '0 A CD fl.
� tlo
0 4. 4.. 4_: I:iii ;•=t7 2IL 3 -.
.� s S O ar fD in fD
co
7 Center Lino P.r • fD M O C.
4 > c ��. .11 W .0 n v, Oao 3 L7
H Er m 3 c C 7 fD fro C
N :IV f]. 5• H 1
F. ;t—� O 7 0o S c.
< co y fD rr
E. A 3 S tl0 fD
Tr c fD 13 x
O ' • •r 6 v, fD U,
= C '6 72 0.) 0- cu)
a fD .,
0 10
N 4 O 3- n S a
o' p a 70
RI-
RD V N 0- fp 'v • 4 .
. LO en
-n L1D
m o o S Iv A * C In
- - % al °;N 0 –• o - m
----------- ---
--_ - C)A
30_in _ -ON C..-e 0O_ hWO = ®A -, Qo fD IA V w 03
QTRINITY ER®
6.3.5 Minimum Nailing-ProEdge Hip&Ridge Shingles:
Prevailing Standard
—11"
Wind Direction Fastening
Sealant StripPattern }
6"Exposure c
Ft 1.iI*2"
illiM"
12° I r—Sealant
/
ON Fasten 7'J\ j
7�!=" 6"Exposure
t
C venerposed1 I
Fasteners with
�` \Roof Cement 'c I. 12"--.1
6.3.6 Minimum Nailing—DuraRidgeTM Hip&Ridge Shingles:
Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer to Owens Corning
published installation instructions for their minimum requirements.
Pravaiing Wind Dirocdon Vuo View
'r—Diro¢iondamininra&nxat 441t.II. V[ueenp plan 1-141.nr
Dirocdon dal vianta prod:minvsto
T �cio'u
s
lb%-- —t , 2,�.e 1• Owens Corning Sure
C��01iO
8losm
SlQI I
"� Ia
ap
slgb
= F l ♦ st iv lag .
It ��yel� u I.1
I
I
fa" — a 1 I2- >I
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1. 1
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC—QUA9625;(631)546-2458;Kanchi.Agrawala-Dokania@ul.com
- END OF EVALUATION REPORT-
j
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 8 of 8