No preview available
HomeMy WebLinkAbout2017 Owens Corning manf specsA 1 [ .� FFii" fn' EVALUATION REPORT Owens Corning One ©wens Corning Parkway Toledo, OH 43659 (740)404-7829 EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization #9503 353 CHRISTIAN STREET, UNIT #13 OXFORD, CT 06478 (203) 262-9245 Evaluation Report 037940.02.12-1118 FL10674-R13 Date of Issuance: 02/06/2012 Revision 8: 10/09/2017 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 61h Edition (2017) Florida Building Code sections noted herein. DESCRIPTION: Owens Corning Asphalt Roof Shingles LABELINrs: (Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein and FBC 1507.2.7.1 / R905.2.6.1. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. TrinitylERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity[ERD Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 8. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCA ANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 10/09/2417. This does not serve as an electronically signed document. CERTIFICATION OF INDEPENDENCE: 1. TrinitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Trinityl ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither TrinitylERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. '�,-�TPJNMYJERD ROOFING SYSTEms EVALUATION: 1. SCOPE; Product Category: Roofing Sub -Category: Asphalt Shingles Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have demonstrated compliance with the following sections of the 6'h Edition (2017) Florida Building Code and Florida Building Code, Residential Volume through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations/ Conditions of Use set forth herein. 2. STANDARDS. Section Property Standard Year 1507.2.5, R905.2.4 Physical Properties ASTM D3462 2010 1507.2.7.1, 8905.2.6.1 Wind Resistance ASTM D3161 2016 1507.2.7.1., R905.2.6.1 Wind Resistance ASTM D7158 2011 3. REFERENCES: Entity Examination Reference Date UL LLC (CER9626) Physicals & Wind Resistance File R2453, Vol. 3 02/15/2007 UL LLC (CER9626) Physicals & Wind Resistance 20120516-R2453 05/16/2012 UL LLC (TST9628) Physical Properties 06CA20263 04/18/2046 UL LLC (TST9628) Wind Resistance 11CA34308 02/18/2012 UL LLC (TST9628) Physicals & Wind Resistance 4786093137 02/01/2014 UL LLC (TST9628) Wind Resistance 4786126532 02/10/2014 UL LLC (TST9628) Physical Properties Classification letter 02/13/2014 UL LLC (TST9628) Physical Properties Classification letter 10/02/2015 Miami -Dade (CER1592) FBC HVHZ Compliance Various NOAs Various UL LLC (QUA9625) Quality Control Service Confirmation Exp. 05/16/2020 4. PRODUCT DESCRIPTION: 4.1 Asphalt Shingles: 4.1.1 Classic' and Supreme' are fiberglass reinforced, 3 -tab asphalt roof shingles. m 4.1.2 Berkshire are fiberglass reinforced, 4 -tab asphalt roof shingles. 4.1.3 Devonshire'" are fiberglass reinforced, 5 -tab asphalt roof shingles. 4.1.4 Duration, TruDefinition' Duration', Duration' Premium Cool, TruDefinition Duration" Designer Calor Collection, Tru Definition' Oakridge', Oakridge' and WeatherGuard' HP are fiberglass reinforced, laminated asphalt roof shingles. 4.2 Hip & Ridge Shingles: 4.2.1 Berkshire® Hip & Ridge Shingles, High Ridge, WeatherGuard' HP Hip & Ridge Shingles, ProEdge Hip & Ridge Shingles and DuraRidge'" Hip & Ridge Shingles are fiberglass reinforced, hip and ridge asphalt roof shingles. 4.3 Accessory Starter Strips: 4.3.1 Starter Strip Shingle, Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles. S. LIMITATIONS: 5.1 This is a building code evaluation. Neither Trinityl ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions. 5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire ratings of this product. Exterior Research and Design, LLC, Evaluation Report 037940.02.12 -RB Cerrditcnre ofAurhorizarlon #9509 6'" EDITION {2017) FISC NON.HVHZ EVALUATION FL10674-R13 Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 2 of 8 TT�INJW ER® 5.4 Wind Classification: 5.4.1 All Owens Corning asphalt shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for use in all wind zones up to Vasd = 150 mph (V,,It = 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.2 All Owens Corning hip 8a ridge shingles, Starter Strip Shingle and Starter Strip Plus noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and 8905.2.6.1 to ASTM D3161, Class F, indicating the shingles are acceptable for use in all wind zones up to Va,d = 150 mph (V„It = 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.3 Classification by ASTM D71S8 applies to exposure category B or C, as defined in FBC 1609.4.3, and a mean roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. 5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations. 5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C. Rule 61G20-3. 6. INSTALLATION: 6.11 Underlayment: 6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product Approval, or be Locally Approved per Rule 61G20-3, per FBC 1507.2.3, 1507.2.4 or R905.2.3. 6.2 Asphalt Shingles: 6.2.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following exceptions: i Berkshire' shingles require minimum five (5) nails per shingle. > WeatherGuard HP shingles require minimum six (6) nails per shingle. F Devonshirer" shingles require minimum six (6) nails per shingle. > Starter Strip Shingle and Starter Strip Plus require minimum five (5) nails per strip. Refer to Owens Corning published information on wind resistance and installation limitations. 6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required. See figures below for details. 6.2.5 Minimum Nailing —Starter Strip Shingle and Starter Strip Plus: Felt undetlagntent s, Deck Self -adhered x Wealherlosk" Drip— .: underlayntent Drip_ Drip edge edge Na7s located -'Nails lOuter Instalfirst Starter Strip %us 2"-3" front eave Install first Self-sealing adhesive Starter Stripp positioned along eave shingle with S" removed Starter Strip siningleoverhangseaves and takes !j' V Fekundedayment F.r Deck SeNedhered WeatherLorlit underlayment grip edge Drip— edge Na7s located _ 2"-3" from eave Instalfirst Starter Strip %us _ Stillaealing adhealve posidonedalong eave wlthS,removed-------- --�-• °' Starter Strip Me overhangs eaves and rakes 174'AM' Exterior Research and Design, I.I.C. Evaluation Report 037940.02.12-R8 Certificate of Autharizatian #9503 if" EDITION {20171 FBC NON-HVHZ EVALUATION F110674 -R13 Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 3 of 8 6.2.6 Minimum Nailing --Classic®& Supreme: Normal Mansard or Area pars VWnd Areas Nigh Wind dssvensa y Arse pare vientoa narmafea Arepa viontae IaarUs �' iA1 w w ig z w ww• 5" Expawre Zko"te " 6.2.7 Minimum Nailing— Berkshire®: Standard Fastening Pattern �l 1 KILN ERD Normal Mansard or /incl pare Wind Areas Migh 1"nd daavanaa y Area pare vfentw non"tea Areas vientaa faerba r IIII w" a" z (B a• t• 4 g 618' Exposure !ltp0e1016e 8aa1ant strip 1a tko de ratador a th' 8 W 1" 1 6 -Nail Fastening Pattern Seabrg Strip La th de oWkdk . rSyt' • 0 eS ►a.0- vp vp S -e 1" e _ 1 re •�rr Asomit Rafinso moral f; eaaata da reeho de asialm Mansard or Steep Slope Fastening Pattern Exterior Research and Design, I.I.C. Evaluation Report 037940.02.12-118 Certificate of Authorizatlan M03 6rK EDITION (2017) FeC NON-HVHZ EVALUATION FL10674-RlS Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 4 of 8 6.2.8 Minimum Nailing- Devonshirerm: N - GIFY07 Rill" exposure Sealant laatian bixisitilb de 5 -5/8 ping U6leed6n doi seliadur 6.2.9 Standard 6 -Nail Fastening Pattern QoTpj"Ty I ERD Mansard or Steep Slope Fastening Pattern e Minimum Nailing - Duration®, TruDefinitian Duration, Duration Premium Cool & TruDefinition Duration Designer Color Collection: 4 -Nall Fastening Pattern SEveNallNtMW" moa WWtlE Nae, tip" t" 5r tr t" FT -0 �,w..o�....x--�,•-moi , -tea w" -o.. wa.+ lila" ed'a- Standard Fastening Pattern e.NaiI Fastening PatterneN heeaaM" Wa WNMa re NATO" it ' r 4- 111: 6afr' ".ems• pea Greater Than 21:12 wnxre taatx"ng ana MOt� r- malt, 1W.] IW f 1" Spas tlAaPIWI RooaEEp wawEiE 6 -Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern Exterior Research and design, I.I.C. Evaluation Report 037940,02.12-R8 Certificate ofAuthorhntion 119503 0 EDITION 12017) FK NON-HVHZ EVALUATION FL10674-R13 Owens Corning Asphalt Roof Shingles Revision 8:10/04/2017 Page 5 of 8 6.2.1 Minimum Nailing–Trul)efinition�Oakridge®, Oakridge®: 4 Nail Pattern Esquema con 4 clavos 6 518" ExposureNails 5 618" Exposu�m &pas1d*nde66/8Pu1g• clauos EwsfdOnde6618putg. Standard Fastening Pattern TRwirrlERo 6 Nall Pattern Esguema can 6 clavos Nal9s 5 518" Expose 5518"Exposure GWas Expa9Wr?do65/8Pedg. &posPeicn da bdlBPulg. 6 -{ail Fastening Pattern 6.2.1 Minimum Nailing – WeatherGuard® HP: F-- �—plfsingle iVie"ka d •z; :`�� '•.r• ThWA* ���Jeiwle�l�arfilr Exterior Research and Design, LLC. Evaluation Report 037940.02.12-R8 Certff ote ofAurhorizarlon 179503 6" EDITION {2017) FBC NON-HVHZ EVAWATION FL10674-713 Owens Coming Asphalt Root Shingles Revision 8:10/0912017 Page 6 of 8 TRINITY ERD 6.3 Hip & Ridee Shingles: 6.3.1 Installation of Berkshire Hip and Ridge Shingles, High Ridge, WeatherGuard HP Hip and Ridge Shingles and ProEdge Hip & Ridge Shingles shall comply with the Owens Corning current published instructions, using four (4) nails per shingle. installation of DuraRidge"' Hip & Ridge Shingles shall comply with the Owens Corning current published instructions, using two (2) nails per shingle. Refer to Owens Corning published information on wind resistance and installation limitations, including the use of hand -sealing for wind warranties. 6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.3.3 Minimum Nailing — Berkshire® Hip & Ridge and High Ridge: Fig. 2 Tap'A" sweView Nods Is t' T Top '"b' tm i' Pima a Y 1 i �I JI 8' �I I 1 I I I I I 6.3.4 Minimum Nailing—WeatherGuard® HP Hip and Ridge: Fig. A a 4 Pre4aa91g 4YAld� %tMrectbn F' �• A••� A Nails`""i'44 A i I l I I I ,15 4 I I y I I W W Fig. G Hip S Ridge Shingle Fastening TapView Nails Mils T� 7• Z. 1` 1' g' Fkpisuw Exterior Research and Design, I.I.C. Evaluation Report 037940.02.12-R8 taWftcate OfAuthorkation 98503 em EDITION (2017) FBC NON-HVHZ EVALUATION FL10674-R33 Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017 Page 7 of 8 6.3.5 Minimum Nailing - ProEdge blip & Ridge Shingles: Prevailing Wind Direction Sealant Strip A—` a' SlEposure Fasten 711z" Cover Exposed Fasteners with Roof Cement - TTRINffYIERD Standard .-�11'—� Fastening Pattem 12" Sealant 7'!e" e" Exposure 6.3.6 Minimum Nailing - DuraRidgeTm Hip & Ridge Shingles: Note: The drawings below pertain to minimum, as -tested attachment requirements. Refer to Owens Corning ublished installation instructions for their minimum requirements. p pnnairng Wind Direcdm �'- Dimaionda iri ntadu+mc Direcdtndolvimroprod: nimnra Ind' 'R b e I I Ctarro�tl'+�, _ v r I I I I a I I I°tsjl 7. LABELING: 7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. 7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC Table 1507.2.7.1 / R905.2.6.1. 8. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 9. MANUFACTURING PLANTS: Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA requirements. 10. QUALITY ASSURANCE ENTITY: UL LLC- QUA9625 ; (631) 546-2458; Kanchi.Agrawala-Dokania@ul.com - END OF EVALUATION REPORT - Exterior Research and Design, W.C. Evaluation Report 037940.42.12-118 Certificate ojAuthorixation#9503 6" EDITION (2017) FBC NON-HVH2 EVALUATION FL10674-R13 Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 8 of 8 Top View Vae on plan - II- Visrassgerior I'I- 2W, 2 W, e pWgASC011ing S11RNWr''P a ChW V I awl.. C 4 v u I� g-, a 1*- 17" I 7. LABELING: 7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. 7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC Table 1507.2.7.1 / R905.2.6.1. 8. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 9. MANUFACTURING PLANTS: Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA requirements. 10. QUALITY ASSURANCE ENTITY: UL LLC- QUA9625 ; (631) 546-2458; Kanchi.Agrawala-Dokania@ul.com - END OF EVALUATION REPORT - Exterior Research and Design, W.C. Evaluation Report 037940.42.12-118 Certificate ojAuthorixation#9503 6" EDITION (2017) FBC NON-HVH2 EVALUATION FL10674-R13 Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 8 of 8