HomeMy WebLinkAboutProduct Approval RECEIVED EXTERIOR RESEARCH St DESIGN, LLC.
Certificate of Authorization#9503
APR 12 2018 353 CHRISTIAN STREET, UNIT#13
Q0TRINITY11ERD OXFORD,CT 06478
T. i.uelo County, Permitting (203)262-9245
EVALUATION REPORT
Owens Corning valuation Report 037940.02.12-R8
One Owens Corning Parkway FL10674-1113
Toledo,OH 43659 Date of Issuance:02/06/2012
(740)404-7829 FILE COPYRevision 8: 10/09/2017
SCOPE:
This Evaluation Report is issued under Rule 611320-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 6th Edition (2017) Florida Building Code
sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein and FBC 1507.2.7.1/R905.2.6.1.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. TrinitylERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 8.
Prepared by:
STTS OF
Robert J.M.Nieminen,P.E. %�S�iv;''`ti";,' The facsimile seal appearing was authorized by Robert
Florida Registration No.59166,Florida DCA ANE1983 "W" Nieminen,P.E.on 10/09/2017. This does not serve as an
electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. TrinityJERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity I ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
TRINITY ERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles,as produced by Owens Corning, have demonstrated
compliance with the following sections of the 6th Edition (2017) Florida Building Code and Florida Building Code,
Residential Volume through testing in accordance with the following Standards. Compliance is subject to the
Installation Requirements and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Prope Standard Year
1507.2.51 R905.2.4 Physical Properties ASTM D3462 2010
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2016
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2011
3. REFERENCES:
Entity Examination Reference Date
UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007
UL LLC(CER9626) Physicals&Wind Resistance 20120516-132453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various
UL LLC (QUA9625) Quality Control Service Confirmation Exp.05/16/2020
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Classic and Supreme are fiberglass reinforced,3-tab asphalt roof shingles.
4.1.2 Berkshire are fiberglass reinforced,4-tab asphalt roof shingles.
4.1.3 Devonshire TM are fiberglass reinforced,5-tab asphalt roof shingles.
4.1.4 Duration, TruDefinition' Duration, Duration Premium Cool, TruDefinition Duration Designer Color
Collection, TruDefinition*Oakridge*, Oakridge and WeatherGuard* HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.2 Hip&Ridge Shingles:
4.2.1 Berkshire* Hip & Ridge Shingles, High Ridge, WeatherGuard' HP Hip& Ridge Shingles, ProEdge Hip & Ridge
Shingles and DuraRidgeym Hip&Ridge Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles.
4.3 Accessory Starter Strips:
4.3.1 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report,or previous versions thereof, is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory
for fire ratings of this product.
Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6'EDITION(2017)FBC NON-HVHZ EVALUATION F1.10674-1113
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 2 of 8
TRINITY ERD
5.4 Wind Classification:
5.4.1 All Owens Corning asphalt shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1
and R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158,Class H, indicating the shingles are acceptable
for use in all wind zones up to Vasd = 150 mph (V,lt = 194 mph). Refer to Section 6 for installation
requirements to meet this wind rating.
5.4.2 All Owens Corning hip & ridge shingles, Starter Strip Shingle and Starter Strip Plus noted herein are
Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the
shingles are acceptable for use in all wind zones up to Vasd=150 mph(V„ft= 194 mph). Refer to Section 6 for
installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category B or C, as defined in FBC 1609.4.3, and a mean
roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions
outside these limitations. Contact the shingle manufacturer for data specific to each shingle.
5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C.Rule 61G20-3.
6. INSTALLATION:
6.1 Underlayment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 611320-3, per FBC 1507.2.3,1507.2.4 or R905.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using
minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following
exceptions:
➢ Berkshires shingles require minimum five(5)nails per shingle.
➢ WeatherGuarde HP shingles require minimum six(6)nails per shingle.
➢ DevonshireTM shingles require minimum six(6)nails per shingle.
➢ Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. See figures below for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
Felt undedayment Delle Felt onderbyrnerrt Deck Sd4&ered
WeatlrorL.ode�a
Self-adhered underlayment
Weatherl-ocka
underlayment
edge_ Dnp edge Drip
Dripedge
edge
Nails located Nai located
res"from eave
2"-3"from eave
l astall first Self-sealing adhesive Instd first Starar P Pkn Sd ka*v admires
Starter Strip \ positioned along eave with 6"removed .• P do"aava
shinglewrth '•.,. ••.•
6"removed
Starter Strip shingle overhangs eaves and rakes'/i 4i" Snrter Strp PWa warh-ngs saves and rakes 1/4-3/4"
Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 61H EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 3 of 8
INIF E
6.2.6 Minimum Nailing—Classic®&Supreme:
Normal Mansard O► Area pare Normal Mansard or Area pare
Wind Areas High Wind desvanes y Wind Areas High Wind desvanes y
Area pare vie Mos normals! Areas vfentos fuertes Area para vientos normales Areas vientos fuertes
IA) ,B (A) — (B►
r �• � z• x• t � _ r r z• r r-�
•r ,z, u,
P
5"Exposure 5 5/8"Exposure
Exposition Exposition
6.2.7 Minimum Nailing—Berkshire®:
3+alant 161- Sealant stnp
to tire da se!latia La i.n,de seUadoi
i • • • • •
Standard Fastening Pattern 6-Nail Fastening Pattern
SraFant aip
La tva de sellatior
-----------0. •� .•F re
r
r � -
r Asphalt roofing cement
Ceaento de techo de astaho
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-118
Certificate ofAuthorization#9503 6T"EDITION(2017)FBC NON-HVH2 EVALUATION 1`11.10674-1113
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 4 of 8
QOTRINITYIERD
6.2.8 Minimum Nailing—Devonshire':
1'= 7" i 8„ i 8" 8" T'
N
...... Cuva
Nab
r c r
5.5/8'exposure Sealant location
Exposiciiin de 5.5/8 ping
Ubicacion del sellador '
Ten 1"Spots of As haft Roof Cement
Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern
6.2.9 Minimum Nailing — Duration®, TruDefinition® Duration, Duration® Premium Cool & TruDefinitione
e
Duration Designer Color Collection:
4-Nail Fastening Pattern 6-Nail Fastening Pattern
sureNain9 Waning ana wWm SueNNle tastin0 area Wath
Nall,lYpical
12" _ 2UN,1YWn1
t^ ttx^ t^ t tr tr t^
......., ...,..,,.n,: • e,..ec�N„r • i�naru. eo...c.rrawwra_._�
8-tq" s sn" 6-t T' 6dle"
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slopes Greater Than 21:12
sunN Int toning w{EM
Nail,Typ 1
12' t'
M-e...w..r• nr m»e a w.yuw�(.
6-1n"s-sls"
�x.
tour t^spoor or A.p,.h Roo"Cm
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6'EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 5 of 8
TRINITY ERD
6.2.1 Minimum Nailing–TruDefinition*Oakridge®,Oakridge®:
4 Nail Pattem 6 Nail Pattem
Esquema con 4 claws Esquema con 6 clavas
t^ 1'
V r
Imo— rr —►I {E— tr'—�{
IF 12-
6 5a,
•55/8"Exposure Rams 5 5/8"Exposure Nails
Fxposiamrde65/0pdq. clavas Exposiraonde56/Spulg. 55/8"Exposure Clavas 5518 Exposure
Exposici6n de 6 5/8 pulg. Exposidtin de 6 5/8 ping.
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slopes Greater Than 21:12
Suw.N..h.t.mne sr.3 w1eM
t
1
2 �NY,ltrp4al
6-ire•. 5 y9..
*-12'
►our t'Spots-9'-ph-ft Room,C—M
Mansard or Steep Slope Fastening Pattern
6.2.1 Minimum Nailing–WeatherGuard®HP:
Onb,liVbwd
s:ti :•'i: lion=ilWwl� flir
Ci1�aw Lirr i fiFdis
Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9SO3 6'EDITION(2017)FBC NON-HVH2 EVALUATION F1.10674-1113
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 6 of 8
TRINITY ERS
6.3 Hip&Ridge Shingles:
6.3.1 Installation of Berkshire* Hip and Ridge Shingles, High Ridge, WeatherGuard' HP Hip and Ridge Shingles
and ProEdge Hip & Ridge Shingles shall comply with the Owens Corning current published instructions,
using four (4) nails per shingle. Installation of DuraRidgeTMl Hip & Ridge Shingles shall comply with the
Owens Corning current published instructions, using two (2) nails per shingle. Refer to Owens Corning
published information on wind resistance and installation limitations, including the use of hand-sealing for
wind warranties.
6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berkshire®Hip&Ridge and High Ridge:
Fig.7 4 Fig.2
�- Pmaikm MNltl
Dseaion p TopVlm SI"VNsa
Nalls Nails
\ 4
Top LaMmled r 7
A I 1 Y Plss
I 1
A i i r r
4 I a
1 I
Epwlrle �
I
I
I
I
I
I
6.3.4 Minimum Nailing—WeatherGuard®HP Hip and Ridge:
Fig.A 9 T Fig.C Hip&Ridge Shingle Fastening
13maNalg Wind Top Vlew
f-Dlwtim p _
A
MSAs����] Y
A � � r,all,; ww
p I I
2.�I Z„
I 1
1 I I 1 �' �•
A I i I I
I I
�E7gowll
S' EYp08UR
1 17
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6T"EDITION)2017)FBC NON-HVHZ EVALUATION F1.10674-R13
Owens Corning AsphaR Roof shingles Revision 8:10/09/2017
Page 7 of 8
Q0TRINITYIERD
6.3.5 Minimum Nailing-ProEdge Hip&Ridge Shingles:
Prevailing Standard �.
Wind Direction FasteningSeallant
Sealant Strip Pattern
8'Exposure T-I r� ~�-� I•T
12' i So""
Fasten 71' �'h6"Expes
cover x
Faab witEpoaahd 1
Raaf Cenent
6.3.6 Minimum Nailing—DuraRidge'm Hip&Ridge Shingles:
Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer to Owens Corning
published installation instructions for their minimum requirements.
Pnaing Wind Dirxdm T*pVbw
~—Direaien dornimnto du ant WE r
Direcdon del•irrto predQt�atr II" vied wgerkr I'
ILiY • 2 , • Orveru Coning Su~ • �"e
Gast\ I � I
•IS
•
g
I
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC—QUA9625;(631)546-2458; Kanchi.Agrawala-Dokania@ul.com
- END OF EVALUATION REPORT-
Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6T'EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-1113
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 8 of 8