The URL can be used to link to this page

Home My WebLink AboutProduct ApproalMIAM4DADE MIAMI-DADE COUNTY E PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOM w .miamidade.sovieconomv Maxim Industries, Inc. 1630 Terre Colony Court Dallas, Texas 75212 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER-Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Model BCM Curb Mount Skylight APPROVAL DOCUMENT: Drawing No. MS0217, titled "Model BMC Dade Curb Mount Skylight", prepared by Maxim Industries, Inc., dated February 10, 2017, sheet 1 and 2 of 2, signed and sealed by Theodore Berman, P.E., on February 10, 2017 bearing the Miami -Dade County Product Control Approval stamp with the Notice of Acceptance number and the approval date by the Miami -Dade County Product Control Section. MISSILE IMPACT RATING: Large and Small Missile Impact Resistant LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and the following statement: "Miami -Dade County Product Control Approved or MDCPCA", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA consists of this page 1, evidence submitted page E-1 as well as approval document mentioned above. The submitted documentation was reviewed by Helmy A. `M�(7akar, P.E., M.S. MIAM4DADE COUNTY jQ, ` f NOA No. 17-0411.02 �Ut�IU� , . • , Expiration Date: 08/03/2022 O8fa �?-Z/7 Approval Date: 08/03/2017 Page 1 Maxim Industries, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED A. DRAWINGS 1. Drawing No. M50217, titled "Model BMC Dade Curb Mount Skylight", prepared by Maxim Industries, Inc., dated February 10, 2017, sheet I and 2 of 2, signed and sealed by Theodore Berman, P.E., on February 10, 2017. B. TESTS 1. Test reports on ])Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 along with marked -up drawings and installation diagram of Model BCM, prepared by Intertek/Architectural Testing, Test Report No. G5934.01-801-18, dated 01103117, signed and sealed by Tyler Westerling, P.E. C. CALCULATIONS Anchor calculations, 7 sheets, issued by Ted Berman and Associates, LLC, dated March 30, 2017, signed and sealed by Theodore Berman, P.E. D. QUALITY ASSURANCE 1. Miami Dade County Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATION 1. None. F. STATEMENTS 1. Florida Building Code, 2014 Edition, Compliance Letter issued by Ted Berman and Associates, LLC, dated March 30, 2017, signed and sealed by Theodore Berman, P.E. L,Helmy A. Makar, P.E., M.S. Product Control Section Supervisor NOA No. 17-0411.02 Expiration Date: 08/03/2022 Approval Date: 08/03/2017 E-1 Model BCM Design Pressure = +60psf/ -60psf (test pressure = +180psf/-120psQ Frames Width = 72,5' (Maximum) C6 j 0 0 N II m c W n O DL Opening = 60.000" —41 4" from ea Corr r Max 6" O.0 L f d z e X h p Fv Notes: 1. This skylight is designed to comply with all requirements of the 2014 edition of the Florida Building Code. 2, This skylight is designed to comply with all winds zones, including the HVHZ, of the 2014 edition of the Florida Building Code. 3. This skylight meets small & large missle impact resistance TAS -201 and no other protection is required. 4. This skylight complies with TAS 201, 202, 203 5. This skylights complies with AAMA/WDMA/CSA 101/I.S.2/A440 and AAMA 101 6. All sizes equal to or less than the test size total square footage are to be accepted under this product approval; NOA, FBC#, TDI Report, UFC 4-010-01, and GSA-TS01-2003. 7. All framing, roof deck, Flashing, and fasteners are by others and must comply with the 2014 Florida Building Code or local building code. S. For attachment of skylight to curb see bill of materials. Spacing shall be 4" from each corner and 6" on center maximum. E U 910 X .375" fastener o� r —1—(see Detail #1 &BOM #B) Corner Detail see Detail #1 & #4) nstallation Fastener Others (see note 8) Frame Detail Detail #1, #3 & #4) Glazing Edge Detail see Detail #1 & #2) Bill of Materials: 1. 6063-T5 Extruded Aluminum Frame mitered and welded at four corners. 2. 6063 -TS Extruded Aluminum Angle, 2" X 2", mitered and welded at four corners. 3. Covestro SL or PalRam UV Enhanced .118" Polycarboante dome. 4. Gallina PoliCarb 5 Layer 16mm RDC Multiwall Polycarbonate. S. Dow Corning 795 Silicone Building Sealant located between aluminum angle and outer dome. 6. ITV✓ SM 5127 Sealant Tape located between 16mm RDC muldwall and extruded aluminum frame. 7. #10 X.375" Stainless steel fasteners 4" from each corner, maximum 6" on center. 8. For Wood Curb #12 x 1.5 SS Min. Wood Density= 0.42 Min. Embedment 1- 1/4" Min. Edge Distance 2-1/2" Date gy 10 FM ME X O � ❑ U V U) M O Ft -L d Q T Q N L co N to 0 a)OD O N � (Jp]o 0 .LC 'tcoo C2 Q � uo N M No OR814 >TAT�= OF THEODORE BERMAN, P.E. NO, 09814 0010117 DATE: 02/10/17 DWG #: MS0217 I SCALE: N.T.S. I SHEET: 1 of 2 Detail #2: Glazing Detail Covestro Makrolon SL - or PalRam PalSunm UV Enhanced Polycarbonate.118" Dome Gallina USA PoliCarb- 5 Layer RDC Multiwall Polycarbonate ITW SM5127 Sealant Tape; .625" X .50" or Essenta VHB Acrylic Tape; 1" X .090" Detail #1: Frame, Angle & Glazing Section Detail Covestro Makrolon SL® or PalRam PalSun- UV Enhanced Polycarbonate .118" Dome Gallina USA PoliCarb- 5 Layer RDC Multiwall 0.630'716mm Polycarbonate OSI® Quad- Max Sealant Detail #3 Aluminum Shape Weld Detail AFCO Part #AF -4950 Maintain weld height - no "V" weld acceptable. Location of heliarc weld APRT'`; as cc:Ta1?,'i,6 w�ci'= ux: ' 10A#f-7 — ffi -0 0 Minimum .25" weep hole located at each corner. Detail #4 Lv �ytvWI - `'E'�'., Aluminum Angle Weld Deta AFCO Part #AF -4230 NO 09014 2"X2 = zw 'Z -O. --G STATE 0,F y"4u a: w ��7�lfEtnSiiSz��4 ® THEODORE BERMAN, P.E. NO. 09814 Location of heliarc weld 02110117 DATE: 02/10/17 DWG #: MS0217 SCALE: N.T.S. SHEET: 2 of 2 h U� z Z 0 LID- U � w}� 20_ z� ED H JO O } 0::D V Dow Corning- 795 Silicone Building Sealant; 2" glazing bite. LU ITW SM5127 Sealant Tape; .625"X.125" Q W Q .085" 6063 TS Extruded aluminum angle. o #10 X.375" stainless steel fastener. ��rr 6063 TS Extruded aluminum frame. W Minimum #12 X 1.5" stainless steel F fastener with minimum 1.25" embedment. All framing, roof deck, flashing and curb CO renderings are for testing and or rendering (p I„_ c- E purposes only and all components, other Q3 Ri a) O than the tested skylight specimen, are by pig U others. C U) 03 O °.omo 0 CL <a o` ` r OD m E m o Q a1) —no c `o .E V ? �30. <� Q Gf� 3 N Co Detail #4 Lv �ytvWI - `'E'�'., Aluminum Angle Weld Deta AFCO Part #AF -4230 NO 09014 2"X2 = zw 'Z -O. --G STATE 0,F y"4u a: w ��7�lfEtnSiiSz��4 ® THEODORE BERMAN, P.E. NO. 09814 Location of heliarc weld 02110117 DATE: 02/10/17 DWG #: MS0217 SCALE: N.T.S. SHEET: 2 of 2