HomeMy WebLinkAboutProduct Approval 4
EXTERIOR RESEARCH&DESIGN,LLC.
Certificate of Authorization#9503
J����' E�® 353 CHRISTIAN STREET,UNIT
OXFORD,CT 06478478
(203)262-9245
EVALUATION REPORT
Owens Corning 'Evaluation Report 037940.02.12-R8
One Owens Corning Parkway FL10674-1113
Toledo,OH 43659• Date of Issuance:02/06/2012
(740)404.7829 Revision 8: 10/09/2017
SCOPE: "
This Evaluation.Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance, with the 6th Edition (2017) Florida Building Code
sections noted herein.
DESCRIPTION:,,OwenscGorriingAspheltRo`ofShingles. -,
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein and,FBC 1507.2:7.1/R905.2.6.1.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen,P.E. if the
product changes or the referenced Quality Assurance documentation changes. TrinitylERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity)ERD Evaluated" may be,displayed in
-advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages'1 through 8.
Prepared by:
aT3
Robert J.M.Nieminen,P.E. .,�;���•_ •:yG;�; i The facsimile seal appearing was authorized by Robert
a'�ln '
Florida Registration No.59166,Florida DCA'ANE1983 Qu W`' Nleminen,RE.on 10/09/2017. This does not serve as an
electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. Trinity IERD does not'have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or.,
distributing products it evaluates.
2. Trinity)ERD is not owned,operated or controlledby any company manufacturing or distributing products it evaluates.
3. Robert Nieminen,P.E.does,not have nor will acquire,a financial Interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen;P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity)ERD nor Robert Nieminen, P.E. are, in any way,_the Designer of_Record for any
project on which this Evaluation Report,or previous versions thereof,is/was,used for permitting or design guidance unless retained
specifically for that purpose.
TRINITY ERS
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning.Asphalt Roof Shingles,as produced by Owens Corning,have demonstrated
compliance with the following sections of the 6t" Edition (2017) Florida Building Code and Florida Building Code,
Residential Volume through testing in accordance with the following Standards. Compliance is subject to'the
Installation Requirements and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Prope Standard Year
1507.2.5,R905.2.4 Physical Properties ASTM D3462 .2010
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2016
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2011
3. REFERENCES:
Entity Examination Reference Date
UL LLC.(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007
UL LLC.(CER9626) Physicals&Wind Resistance 20120516-112453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC--(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/0Z/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various'NOAs Various
UL LLC(QUA9625) Quality Control Service Confirmation Exp.05/16/2020
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shinales:
4.1.1 Classic and Supremes are fiberglass reinforced,3-tab asphalt roof shingles.
4.1.2 Berkshire are fiberglass reinforced,4-tab asphalt roof shingles.'
4.1.3 Devonshire-are fiberglass reinforced,5-tab asphalt roof shingles.
4.1.4 Duration, TruDefinition® Duration®, Duration® Premium Cool, TruDefinition Duration Designer .Color
Collection, TruDefinition Oakridge®, Oakridge® and WeatherGuard® HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.2 Hip&Ridae Shinizles:
4.2.1 Berkshire Hip & Ridge Shingles, High Ridge, WeatherGuard® HP Hip & Ridge Shingles, ProEdge Hip & Ridge
Shingles and DuraRidgeT"Hip&Ridge Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles.
4.3 Accessory Starter Strips:
4.3.1 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
S. LIMITATIONS: .
5.1 This is a building code evaluation. Neither TrinitylERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 Fire Classification is not part of this Evaluation Report;refer to current Approved Roofing Materials Directory
for fire ratings of this product.
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R8
Certificate ofAuthorlsatlon#9503 6'EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R33
Owens Corning Asphalt Roof Shingles Revision 8:10/09/20111
Page 2 of 8
ITRINITY1 ERD
5_4 Wind Classification:
5.4.1 All Owens Corning asphalt shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1
and R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158,Class H, indicating the shingles are acceptable .
for use in all wind zones up to Vasd 150 mph (Vult = 194 mph). Refer to Section 6 for installation
requirements to meet this wind rating.
5.4.2 All Owens Corning hip & ridge shingles, Starter Strip Shingle and Starter Strip Plus notedherein are
Classified in accordance with FBC Tables 1507.2.7.1 and R90S.2.6.1 to ASTM D3161, Class F, indicating the
shingles are acceptable for use in all wind zones up to Vasa=150 mph(V,lt=194 mph). Refer to Section 6 for
installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category B or C,as-defined in FBC 1609.4.3, and a mean
roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions
outside these limitations. Contact the shingle manufacturer for data specific to each shingle.
5.4.4 Refer to Owens Corning published information,on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C.Rule 61G20-3.
6. INSTALLATION:
6.1 Underlavment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 611320-3,per FBC 1507.2.3,1507.2.4 or R90S.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using
minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or 11905.2.6, with the following
exceptions:
➢ Berkshiree shingles require minimum five(5)nails per shingle.
➢ WeatherGuarde HP shingles require minimum six(6)nails per shingle.
➢ Devonshire'"shingles require minimum six(6)nails per shingle.
➢ Starter Strip Shingle and Starter Strip Plus require minimum five(5)nails per strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's.published requirements, but not less than FBC
1507.2.6 or R905°2.S. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. See figures below for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
Felt underlayment Deck Fettundediymertt Deck' Sdkdhered
Sell-adhered d
Weather
WeatherLocka i
underlayment
Drip edge
Drip Drip edge ' Drip-
edge edge '
Nails totaled !' Nags located
2"-3"from eave
2°—r from eave
Install first SeK•sealing adhesive Sdtaed ng adhesive
Starter Strip positioned along eave Instal first Starter Strip Phe positiorredalongeave
shingle with \ with 6°removed \
6"removed
Starter Strip shingle overhangs eaves and rakes'/i=r/i' Starter Stdp Nus overhangs eaves and rakes 1/4-3/4"
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-RS
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHz EVALUATION FL30674-R13
Owens Corning Asphalt Roof Shingles Revision 8:10/09/20111
Page 3 of 8
TRINITY 1 ERD
6.2.6 Minimum Nailing—Classic®&Supreme:
Normal Mansard or Area pare Normal Mansard or Area pare
Wind Areas High Wind desvenes yWind Areas High Wind dosvanes y
Area pare vientos normeles Areas vientos fuertes Area Pere vientos normaies Areas vientos fuertes
(A) �"z (A) �'� �• z' (Bf z• �'
t >I u t
S"Exposure 5 6/8"Exposure
Exposicidn Exposicldn
6.2.7 Minimum Nailing—Berkshire®:
Sealant strip Sealant strip
La tira do se8ador La lira de sellador
8 Yz" 9"Yt' 9 Yt' 8 Yf f "8 Ila" 8 Yt' 8 VV 8 W }
1
1
1
Standard Fastening Pattern 6-Nail Fastening Pattern
Sealant strip
La tirade sellador
`p 8 Yt' 8 Yf 8 Vt' 8 Yf
2" Asphaft roofing cement
Cemento de techo de asiafto
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R&
Certificate ofAuthorhation#9503 6T"EDITION(2017)FBC NON-HVH2 EVALUATION FL10674-R13
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 4 of 81
\,\,J
TRINITY I ER®
6.2.8 Minimum Nailing—Devonshire"":
7tr 8a 8" i 8tr H 7"
N
davoz
Nails
-- •'• r P T t
5.5/8'exposureSealant location �'`'
Fxposirabn de 5.518 pulg Ubicacibn del sellador
Ten 1"Spots of Asphalt Roof Cement
Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern
6.2.9 Minimum Nailing — Duration®, TruDefinition® Duration, Duration® Premium Cool & TruDefinitione
•
Duration Designer Color Collection:
4-Nall Fastening Pattern 6-Nail Fastening-Pattem
Sure Nail®fastening area wicith SureNaIM fastening area M1Eth
Nail,Typical Nail,Typical
1" 12^ I 12" i^ i^ _ 12" � 12" r
�bCwrvnp EveVX •.. +•i ]e^e•p O-m+ tuNW • ae.,".CamyEueAL • I '�Jsvr•. �' •D•mf�ump6vNaiB •
6-1/5"&SR" 6.115^S5B"
I.Cnu. eyau-
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slopes Greater Than 21:12
S..N.Ity Wt.ning M.v"eth
Nail,Typical
1- 12" 12" 1"
�.'�-".i•• -•o....+^... waves
e.lre^s•sre^
�r
Four t-Spol..tAaphall Ii..Sng Cement
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,U.C. Evaluation Report 037940.02.12-R81
Ceniflcote of Authorization#9503 6T"EDITION(2017)FBC NON-HVH2 EVALUATION FL10674-11131
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017'
Page 5 of 81
TRINITY�ER®
6.2.1 Minimum Nailing—TruDefinition'Oakridge'P,Oakridge®:
4 Nall Pattern 6 Nail Pattern
Esquema con 4 clavos Esquema con 6 clavos
r r
5 518"Exposure Nails 5 5/8"Exposure Nails
Exposlelon de 66/0pufg. Clavus Exposiddn de 56/8 pulg. 5 5/8"Expostne Clavus 5 518"Exposure
Exposid6n de 6.6/8 pulp Exposlcldn de 66/8 pulp.
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slopes Greater Than 21:12
S—N111111,11,1119 e1,*11114
N,u,rypkifl
i" 12" I I 12- 1^
S-f18ar,518�
•�2"
Four 1-Spot&of mphe1t Roofing Cement
Mansard or Steep.Slope Fastening Pattern
6.2.1 Minimum Nailing—WeatherGuard®HP:
li-- 2' 7 '--1►I
s: •3 •• FielwfffR7�tt�tlhiilit�
Ci>Mriblfr��
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-REI
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13i
Owens Corning Asphalt Roof Shingles Revision 5:10/09/20171
Page 6 of 131
"INRYIERD
6.3 Hip&Ridge Shingles:
6.3.1 Installation of Berkshire Hip and Ridge Shingles, High Ridge, WeatherGuard® HP Hip and Ridge Shingles
and ProEdge Hip & Ridge Shingles shall comply with the Owens Corning current published instructions,
using four (4) nails per shingle. Installation of DuraRidgeym Hip & Ridge Shingles shall comply with the
Owens Corning current published instructions, using two (2) nails per shingle. Refer to Owens Corning
published information on wind resistance and installation limitations, including the use of hand-sealing for
wind warranties.
6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berkshire®Hip&Ridge and High Ridge:
Fig.1 4 Fig.2
t— Prevailim�VlAnd
Direction A TopView SltleNevi
Naos A Nails NNIS
R
� r I Top laminated
A Piece
A
I I
4 1 I I
I I 1 I I
A I I I I I
I� y W W I
Exposure I
I
I
I
I
I
I
6.3.4 Minimum Nailing—WeatherGuard®HP Hip and Ridge:
Fig.A 44
Fig.C Hip&Ridge Shingle Fastening
Prevalling Wind Top Viety
f—Direction p
A
Nails q q
Nails Nails
A I I 1 •
ANr-
`t' 'i' ♦ r'
£aposure
S. Exposure
12
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-Rg
Certiflcate ofAuthori:ation#9503 6T"EDITION(2017)FBC NON-HVH2 EVALUATION FL10674-R331
Owens Corning Asphalt Roof Shingles Revision 5:10/09/2017'
Page 7 of 8
TRINITY�ER®
6.3.5 Minimum Nailing-ProEdge Hip&Ridge Shingles:
Prevailing Standard
Wind Direction Fastening
Sealant Strip Pattern
6°Exposure 21
12° i Sealant
Fasten 71 z 7�lEp 6°Exposure
Cover Exposed 111 IL
Fasteners with
<Roof Cement I•--12°
6.3.6 Minimum Nailing—DuraRidgelm Hip&Ridge Shingles:
Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer to Owens Corning
published installation instructions for their minimum requirements.
Ptdraifng Wind Diracden Top View
roaiondornimntodivmr �..�li- Vtueenperbr I-IH
Dimodondolvisrrto prodomimma
4 T
s G
n 2!e" . Ovrenv Corning SutnNa➢' . ew»
Clarwr�
I
�I2a
' J
Sld$
I i�,mill
�- i r —,I
7. LABELING:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC
Table 1507.2.7.1/R905.2.6.1.
S. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N-3 QA
requirements.
10. QUALITY ASSURANCE ENTITY:
UL LLC—QUA9625;(631)546-2458;Kanchi.Agrawala-Dokania@ui.com
END OF EVALUATION REPORT-
Exterior Research and Design,I.I.C. . Evaluation Report 037940.02.12-REI
Certificate of Authorization#9503 6TH EDITION(2017)FBC NON-HVHZ EVALUATION F1.10674-11131
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017'
Page 8 of S1