HomeMy WebLinkAboutProduct Approval (2) MIAMI•DADE
o MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami,Florida 33175-2474
T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
Southeastern Metals Manufacturing C mpanv. Inc._
11801 Industry Dr. RECEWED
Jacksonville,FL. 32218
JUL 11 7
SCOPE:
This NOA is being issued under the applicab ST. Lucie Dunt Permi " ruing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County PERA-Product Control Section to
be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section
(In Miami Dade County)and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. PERA reserves the right to revoke this
acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to
meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Aluminum Ridge Vent
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein.
0 RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use,and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
UJfor sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This renews NOA# 12-0426.02 and consists of pages 1 through 3.
k
�� The submitted documentation was reviewed by Freddy Semino
1
NOA No.: 17-0609.03
M;�tDADE COUNTY Expiration Date: 09/20/22
Approval Date: 10/05/17
Page 1 of 3
x.
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub-Category: Roof Vent
Material: Aluminum
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT
Product Dimensions Test Product
Specification Description
Aluminum Ridge Vent W=9-7/16" TAS-100 Aluminum low profile attic ridge vent for
H= 1.5" installation in shingle roof systems.
L=8"
TRADE NAMES OF PRODUCTS MANUFACTURED BY OTHERS
Test Product
Product Dimensions Specification Description Manufacturer
Roofing Nails 11 ga.X 2"x TAS 114 Galvanized smooth shank, Any Miami-Dade
3/8" roofing nail County Listed
Suppliers
Flashing cement Various ASTM D 4586 Cut back, asphalt modified Generic
adhesive for flashing (with current NOA)
attachment.
MANUFACTURING LOCATION
1. Jacksonville,FL.
EVIDENCE SUBMITTED
Test AEency/Identifier Name Report Date
PRI Construction Materials Technologies TAS 100(A) SEM-006-02-01 03/19/07
APPROVED APPLICATIONS
Tradename: Aluminum Ridge Vent
System Type: Mechanical attachment of ridge vent.
Slot: Cut a minimum 2" slot along the apex-of the roof by cutting 1" on each side of the ridge.
The slot shall terminate approximately 6" from the rake edge.
Installation: Install Aluminum Ridge Vent by centering it over the 2"wide opening. Fasten vent to
the the deck with 11 ga. 2"x 3/8" smooth shank galvanized roofing nails placed through
the factory formed nailing locations on the vent.
Ventilation Calculations: Refer to manufacturer's published literature
NOA No.: 17-0609.03
Mtartt•papecouNrir Expiration Date: 09/20/22
Approval Date: 10/05/17
Page 2 of 3
LIMITATIONS:
i
1. Refer to applicable Building Code required ventilation.
2. Ridge Vent shall comply with applicable Building Code.
3. Ridge Vent shall not be installed on rof mean heights greater than 33 feet.
4. Ridge Vent shall comply with 1517.6 of the Florida Building Code(FBC).
5. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
DETAm A
1.5"
9 711
-16
ALUMINUM RIDGE VENT
END OF THIS ACCEPTANCE
NOA No.: 17-0609.03
APPMtAh11DAROVED1 TY Expiration Date: 09/20/22
Approval Date: 10/05/17
Page 3 of 3