HomeMy WebLinkAboutProduct Approval (2) RECEIVED
NOV 0 5 2018
ST, Wrlt County, Permitting
EXTERIOR RESEARCH& DESIGN, LLC.
Certificate of Authorization#9503
TRINITY I 353 CHRISTIAN STREET, UNIT 413
QOERD OXFORD,CT 06478478
(203)262-9245
EVALUATION REPORT
Owens Corning Evaluation Report 037940.02.12-118
One Owens Corning Parkway FL10674-1113
Toledo,OH 43659 1 LE Ittme U, Date of Issuance:02/06/2012
(740)404-7829 Revision 8: 10/09/2017
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 6th Edition (2017) Florida Building Code
sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein and FBC 1507.2.7.1/R905.2.6.1.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 8.
Prepared by: �murrn,,
•o..F, . .,ter,•;._
The
Robertl.M.Nieminen,P.E. appearing wsy Robert
Florida Registration No.59166,Florida DCA ANE1983 NeminenmiPeE5on110/09/2017aThstdoes notserve asan
electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. Trinity lERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinityl ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinity lERD nor Robert Nieminen, P.E. are, in any way,the Designer of Record for any
project on which this Evaluation Report,or previous versions thereof,is/was.used for permitting or design guidance unless retained
specifically for that purpose.
`
. �
ROOFING SYSTEMS EVALUATION: \ ��U " x /ERD
1. SCOPE:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles, es' �producedhy��ensCorni� have demon�r ted
compliance with the following sections of the 6t' Edition (2017) produced
Building Code and Florida Building Code,
�
Residential Volume through testing in �accordance with the following andards. Compliance is subject to the
Installation Requirements and Limitations/Conditions of Use set forth herein.
2' STAmoxnos:
Section Propert/ Standard Year
1507.2.5,R905.2.4 Physical Properties ASTM D3462 znIo
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2016
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D715D 2011
3' RsFsnsmcss,
Entity Examination Reference Date
uLLLC(csRyoos) Physicals&Wind Resistance File R2453,Vol.s 02/15/2007
uLLLC(ccRssls) Physicals&Wind Resistance 20120516'R2453 05/16/2012
uLLLC(TsT962D) Physical Properties no[AzOzoa 04/102006
UL LLC(TST9628) Wind Resistance 11[A34]08 02/18/2012
uLLLC(TSTg678) Physicals&Wind Resistance 4786093137 02/01/2014
ULLLC(TSTg638) Wind Resistance 4786126632 02/I0/2014
uLLLC(TST9sa8) Physical Properties Classification letter 02/13/2014
ULLLC(TsT8G28) Physical Properties Classification letter 10/02/2015
xxiami'Dade(cEnzSsz) FBcHVHZCompliance VariuvsNoAs Various
oLLLC (QVAy6ZS) Quality Control Service Confirmation Exp.05/16/2020
4. PRODUCT DESCRIPTION:
4.1 Asphalt Shingles:
4.1.1 Oasaic^and Supreme'are fiberglass reinforced,3-tabasphalt roof shingles.
4.12 Berkshire'are fiberglass reinforced,4-tabasphalt roof shingles.
4.1.3 DevuushireTmare fiberglass reinforced,S-tabasphalt roof shingles,
4.1.4 Duration~, TruDeOnition^ Duration', Duration' Premium Cool, TruDeOnition~ Duration' Designer Color
[oUecthon, TruDeMnition^Oakh6ge~, Oakridge' and VVpathapGuard^ HP are fiberglass reinforced, laminated
asphalt roof shingles.
4.3 Hip&Ridge Shingles:
4.2.1 Berkshire' Hip & Ridge Shingles, High Ridge, VVeatherGuand^ HP Hip & Ridge Shingles, ProEdgeHip & Ridge
Shingles and DuraRidge'm Hip&Ridge Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles.
4.] Accessory Starter Strips:
4.3.2 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles.
S. UxxnvT/oms:
5.1 This is a building code evaluation. NeitherThnityJERD nor Robert Nieminen' P.E. are, in any Way, the
Designer of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report isnot for use inF8CHVHZjurisdictions.
5.3 Fire Classification is not part of this Evaluation Report;refer to current Approved Roofing Materials Directory
for fire ratings ofthis product.
Exterior no,e^rcx,anuDesign,LLC. Evaluation Report o3m«o.oz12-no
Certificate w'Authorization#9s03 o"'EDITION(zoz/)Facmom-xxxzEVALUATION ruosm'nzs
Owens Coming Asphalt Roof Smnu/m Revision 8:10/09/2017
Page xv,o
TRINITYIERD
5.4 Wind Classification:
5.4.1 All Owens Corning asphalt shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1
and R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable
for use in all wind zones up to Vasa = 150 mph (V„it = 194 mph). Refer to Section 6 for installation
requirements to meet this wind rating.
5.4.2 All Owens Corning hip & ridge shingles, Starter Strip Shingle and Starter Strip Plus noted herein are
Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the
shingles are acceptable for use in all wind zones up to Vasd=150 mph (V,,it= 194 mph). Refer to Section 6 for
installation requirements to meet this wind rating.
5.4.3 Classification by ASTM D7158 applies to exposure category B or C, as defined in FBC 1609.4.3, and a mean
roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions
outside these limitations. Contact the shingle manufacturer for data specific to each shingle.
5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C.Rule 611320-3.
6. INSTALLATION:
6.1 underlavment:
6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 61G20-3, per FBC 1507.2.3,1507.2.4 or R905.2.3.
6.2 Asphalt Shingles:
6.2.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using
minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following
exceptions:
i Berkshire®shingles require minimum five(5) nails per shingle.
> WeatherGuarde HP shingles require minimum six(6)nails per shingle.
Devonshire'""shingles require minimum six(6) nails per shingle.
Starter Strip Shingle and Starter Strip Plus require minimum five(5) nails per strip.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are
required. See figures below for details.
6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus:
Felt undedayment Deck Feltundedayment i Deck W4dhered
{
Self-adhered and r�layment�
WeatherLock*
underlaymeni
Drip edge
Drip_ Drip edge Drip—
edge edge
Nails located Naos located
2'-3'from eave
2"3"from eave
Install first Self-sealing adhesive SeNseiling adhesive
Starter Strip positioned along eave Mittal first Starter Strip Plus •' positioned along eave
shingle with with 6 removed
6"removed
Starter Strip shingle overhangs eaves and rakes 1/4'44" Starter St ip Plus overhangs eaves and rakes t/4'-3/4'
Exterior Research and Design,I.I.C. r Evaluation Report 037940.02.12-R8
certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 3 of 8
TRINITY J ERD
6.2.6. Minimum Nailing—Classic®&Supreme:
Norma! Mansard or Are&pare Normal Mansard or Area para
Wind Areas High Wind desvanes y Wind Areas High Wind desenrnes y
Area pars viontos normals# Areas vientos fuartes Area pans vientos normal** Areas vientas fnertes
fi21 +� t2S
fie• (A) fi' �' Z' (B E2' e' t• _ i(A}� fi^ r ....Z. (B? z. fi.
S Exposure 6 Blti•Exposure
Expo#i06n Exposici6n
6.2.7 Minimum Nailing—Berkshire0:
Sealant strip Sealant strip
to fka de'seCada to tki de sellador
9 w 9 Yf 9 Yf a Yf t `,811' B Sz` 81@"
t- ,•J V
Standard Fastening Pattern 6-Nail Fastening Pattern
Sealard strip
La iks de saltador
t 81(f awl 4-1ci
2• Asphak roofing oemant
Comento da!echo de astabo
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization 119503 6'"EDITION(2017)FBC NON-HVH2 EVALUATION F1.10674-1173
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 4 of 8
f1
f
\\j
TRINITY i ERD
6.2.8 Minimum Nailing—Devonshire'":
1" s 7" l 811 I 8" 8" 7" —1"
N �
davo�
e 7 r
5.5/8'exposure SealaExposici6n de 5.518 pulg Uhicadci6n 6n del location
del sellador Sx• 6L•
Ten 1"Spots of Asphalt Roof Gement
Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern
6.2.9 Minimum Nailing ®_. uDefinition° Duration, Duration® Premium Cool & TruDefinition
Duration Designer Color Collection:
4-Nall Fastening Pattern 15-Nall Fastening Pattern
SurlNalMA tasLting area Width Su N"tasttNng Fns Width
Nall cal Nae, UI
�^ 12" 1r r r 1r
.s+...e..o"..n.e;;. ,,:•- "-^o,.n•'.;,,�.u:r u.b s..w+•a...�: :�. ...v.s i�-1'�^t"- —�—..,.o � I-•a:., —.:,i
6-118^ 5618 f-' i'rhs{{ iinl :i.k6-1e366" li:'111.
F�z`
ko r-r7ry�{ir f,
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for Slopes Greater Than 21:12
S—mw S Mbning area width
Nall,Ty;I
1" 12^ 12- 1'
au•ssra" W11111,
i
Fou11^Spoh of Aaphah Roaarg c—.t
Mansard or Steep Slope Fastening Pattern
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-1118
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 5 of 8
TRINITYD
6.2.1 Minimum Nailing—TruDefinition'OakridgeO,OakridgeO:
4 Nall Pattom 6 NWI Pattom
Esquema con 4 clavos Esquerna con S CJMS
r4
5 5/8"Exposure 5510"Exposuft
Nals NODS
Erposicida do 6 Glepufq. clayos Expo&Wn de 6 GICptig. 5 5/8'Expmfe Claws 5518 Exposure
&posicMnd&G518jatdg Exposici6n do 5518pufg
Standard Fastening Pattern 6-Nail Fastening Pattern
Fastening for slopes Greater Than 21*.12
t..k'Q—width
12' Ir
6.118 5M
-T,
F—V Spots of A.Phft ft—%Q C-4
Mansard or Steep Slope Fastening Pattern
6.2.1 Minimum Nailing—WeatherGuard'HP:
gle side WOW
"MNil Lln�
-
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13
Owens Coming Asphalt Roof Shingles Revision 8:10/09/2017
Page 6 of 8
\ ( TRINITY(ERD
I
6.3 Hip&Ridge Shingles:
6.3.1 Installation of Berkshire' Hip and Ridge Shingles, High Ridge, WeatherGuard' HP Hip and Ridge Shingles
and Prolidge Hip & Ridge Shingles shall comply with the Owens Corning current published instructions,
using four (4) nails per shingle. Installation of DuraRidge'" Hip & Ridge Shingles shall comply with the
Owens Corning current published instructions, using two (2) nails per shingle. Refer to Owens Corning
published information on wind resistance and installation limitations, including the use of hand-sealing for
wind warranties.
6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.3.3 Minimum Nailing—Berksh)reO Hip&Ridge and High Ridge:
Fig.1 oq Fig.2
F— prtvdtinp lMnd
fNredlon A Top Ylew SldeView
Nails—��] A
Nails Nails
4
!E711 Top LanfalW Z'kt
A I I 4- piece
1 I �
4 I I
I
I I I I I
<I
Exposure -I '
Ir
6.3.4 Minimum Nailing—WeatherGuarda HP Hip and Ridge:
Fig.A 9? Fig.C Hip&Ridge Shingle Fastening
PMVattn2Wknd �
lopftw
DlMdb
<—NlrMba
A
Nails
\ ^• I I Nape Nails
Z"
/ \ Ap• I I i I rr �„
I I I I
r • r
Exposure
^ � 5" Exposure
Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8
Certificate of Authorization#9503 6'"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-1313
Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017
Page 7 of 8
. ` .
Qfi:RINITYIERD
�
5.3.5 Minimum Nailing'PrnEdQeHip&Ridge Shingles:
Prevailing Standard
Wind Direction strip Fastening
Pattern
6'Exposure
1-r —I-1 r
Sealant
Fa sten 7111. t
6*Exposure
Cor sod
Fa tor=,th
Roof Cement
63.6 Minimum Nailing—DuraRldge=Hip&Ridge Shingles:
Note The drawings below pertain tominimum,as-tested attachment requirements. Refer toOwens Corning
published installation instructions for their minimum requirements.
Top View
Npak
Ulm
7. LAacuwa:
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FB[
Table 1507.2.7.1/R9O5.2.6.z.
O' BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 9N'3 QA
requirements.
`
10. QUALITY ASSURANCE ENTITY:
UiLLC—{\UA9§2S;(631)545'245D;KanchiAQrawa|a'Dokania@uicom
-
END OFEVALUATION REPORT'
Exterior Research and Design,LLc Evaluation Report oa/94m.u2.zzxo
Certificate of A"mwiz"x" ^9503 o=EDITION(znz7)mcwnm-ovuzEVALUATION ru06/41113
' owvmo,m/voxarxouxvmsunu/es Revision o.zn/os/zoo
Page xn/u