Loading...
HomeMy WebLinkAboutNotice of Acceptance ! y MIAMI--RADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street,Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) Miami,Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T(786)315-2590 F(786)315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidaae.eov/econumy Interwrap,Inc. 32923 Mission Way Mission,BC,Canada V2V-6E4 SCOPE: ` This NOA 1s`lieing issued-under the applicable rales and regulations governing the use of construction materials;The documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ). This NOA shall not be valid after the expiration date stated below. The Miami Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to 'have this product or material tested for.quality assurance purposes. If this product or material fails to perform in the accepted, manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product'is approved as described herein,and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Titanium@ UDL-30/Titanium@ PSU 30,Titanium@ UDL-25 PLUS/Titanium®PSU-30, and UDL-MD(2 ply)/Titanium®PSU-30 Underlayment System LABELING:Each unit shall bear a permanent label with the manufacturer's name or logo,city,state and following statement:"Miami-Dade County Product Control Approved",unless otherwise noted herein. RENEWAL`of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code megatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product, for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section of this NOA shall be-cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it shall be done in its entirety., INSPECTION:A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews and revises NOA#13-0730.01 and consists of pages 1 through 7. The submitted documentation was reviewed by Alex Tigera. NOA No.:14-0603.19 Mtartt.waa> cotnm Expiration Date:01/26/22 Approval Date:02/0V17 Page 1 of 7 i ROOFING'COMPONENT APPROVAL Category: Roofing Sub-Catesory: Underlayment Material: Polypropylene i TRADE NAMES OF PRODUCTS MANUFACTURED BY APPLICANT TABLE 1 ' Test Product Product Dimensions Specification __Description TitaraumO'UDL-25 48"x 250'rolls ASTM D226 Woven synthetic polymer underlayment with one PLUS Type I&II side coated with UV protected and slip resistant polymer stabilized polypropylene on both sides. Manufacturing Location#1&#2 I UDL-MD(2P1y system) 48"x 250'rolls ASTM D226 Woven synthetic polymer underlayment with a Type I&II chemical slip resistant and UV protected coating on Manufacturing both sides. Location#2 i Titamumw UDL-30 48"x 250'rolls ASTM D226 Woven synthetic polymer underlayment with two Type I&H sides coated with UV protected and slip resistant Manufacturing polymer stabilized polypropylene on both sides. Location#1&#2 Titanium@ P,SU-30 36"x 72'rolls TAS 103 Unreinforced polymer modified bitumen material adhered to the underside of a polymer-coated, Manufacturing synthetic woven sheet. The underside is backed Location #3 with a release film. MANUFACTURING LOCATIONS: 1. MLI, 2. ML3 3. MIA- y I I i NOA No.:14-0603.19 MIAMtpAD6 covrmr Expiration Date:01/26/22 M. Approval Date:02/02/17 Page 2 of 7 EVIDENCE SUBMITTED: Test Agencv Test Identifier Test Name/Reno Date Intertek Testing Services #3031783 TAS 104 02/19/03 3124826-01 ASTM E108 02119/08 3119607COQ-003B ICC ES AC48 02/20/08 3130639COQ-002A ASTM D226 02/20/08 3124826MID-007 ASTM E108 02/25/08 3146738COQ-003B ASTM D 1876/TAS 117 03/28/08 3146739COQ-003A ASTM D226 04/22/08 Trinity E" 135520.06.11 TAS 103/TAS 104 06115111 135520.06.11 TAS 103/TAS 104 06/15/11 138010.08.11 ASTM D226 08/11/11 135520.08.11-1 TAS 114 08/12/11 135520.08.11 ASTM D2523/D1781 08/17/11 144970.07.13-Rl ASTM D226,ASTM D1876 09/09/13 and TAS 114(C) NOA No.:14-0603.19 MIAMI-WWECOUNTY Expiration Date:01/26/22 Approval Date;02102117 Page 3 of 7 4 APPROVED TITANIUM UNDERLAYMENT SYSTEM ASSEMBLIES: Deck Type 1: Wood Deck Description: 19/32'or greater plywood or wood plank System E(1): Base sheet mechanically fastened to deck,subsequent cap membtane self-adhered. All General';and System Limitations shall apply. I Base sheet: One or mare plies of Titanium®UDL-25.PLUS or.Titanium®UDL-30 applied with minimum 4"horizontal laps and minimum 6"vertical laps and mechanically fastened as noted below. Note: Titanium@ UDL-30 shall be inverted to provide a smooth bonding surface. Primer is not required when Titanium®UDL-30 is installed inverted(printed side facing down) Fastening: j Miami-Dade approved nails&metal/tin caps spaced 6"o.c.at the 4"horizontal laps and 8" o.c.in a grid pattem1aving three,equally spaced,staggered rows in the field of the sheet. Primer: ; Metal/Tin caps shall be primed with ASTM D41 primer Ply Sheet: (Optional)Titanium@ PSU-30,self-adhered with minimum 3"horizontal laps and minimum 6"vertical laps. Membrane: TitaniumO PSU-30,self-adhered,with minimum 3"horizontal laps and minimum 6" vertical laps. Place the first course of TitaniumD PSU-30 parallel to the eave and field, using a heavy pressure roller under safe conditions to further secure the membrane. Surfacing: Approved for asphalt shingle,mechanically fastened roof tile,foam-on roof tile,metal roofing,wood shakes&shingles or slate roof assemblies. Note: For tile roof assemblies,refer to RAS 118, 119 or 120 and the tile manufacturer's NOA. For foam-on the roof assemblies,approved use with ICP Adhesives Polyset AH-160 and Dow TILE BOND Roof Tile Adhesive. { i NOA No.:14-0603.19 MIAMICADECOTY Expiration Date:41/26/22 Approval Date:02/02/17 Page 4 of 7 Deck Type`1: Wood Deck Description: 19/32" or greater plywood or wood plank System E(2): Base sheet mechanically fastened to deck,subsequent cap membrane self-adhered. All General and System Limitations shall apply. Base sheet:! One or more plies Titanium®UDL-30 applied with minimum 4"horizontal laps and minimum 6"vertical laps and mechanically fastened as noted below. Fastening: ! Miami-Dade approved nails&metal/tin caps spaced 6"ox.at the 4"horizontal laps and 8" o.c.in a grid pattern having three,equally spaced,staggered rows in the field of the sheet. Primer: j TitaniumO UDL-30 shall be primed on the printed side with ASTM D41 primer prior to placement of cap sheet. Ply Sheet; (Optional)Titanium®PSU-30,self-adhered,with minimum 3"horizontal laps and minimum 6"vertical laps. Membrane: Titanium®PSU-30,self-adhered,with minimum 3"horizontal laps and minimum 6" vertical laps. Place the first course of TitaniumUR PSU-30 parallel to the eave,using a heavy pressure roller under safe conditions to further secure the membrane. Surfacing: Approved for asphalt shingle,mechanically fastened roof tile,foam-on roof tile,metal roofing,wood shakes_&shingles or slate roof assemblies. Note: For tile roof assemblies,refer to RAS 118, 119 or 120 and the tile manufacturer's NOA. For foam-on tile roof assemblies,approved use with ICP Adhesives Polyset AH-160 and Dow TILE BOND Roof Tile Adhesive. I I ` i Mtahinape CouN ry NOA No.:14-0603.19 . ,, ,i U Expiration Date:01126/22 Approval Date:02/02117 Page 5 of 7 i Deck Type l: Wood Deck Description: 19/32"or greater plywood or wood plank System E(3): Base sheet mechanically fastened to deck,subsequent cap membrane self-adhered. All General and System Limitations shall apply. Base sheet:! One or more plies of UDL-MD(2Ply system)applied with minimum 4."horizontal laps and minimum 6"vertical laps and mechanically fastened as noted below. Fastening: ; Miami-Dade approved nails&metal/tin caps spaced 6"o.c. at the 4"horizontal laps and 8" o.c.in a grid pattern having three,equally spaced,staggered rows in the field of the sheet. Ply Sheet: (Optional)Titanium(D PSU-30,self-adhered with minimum 3"horizontal laps and minimum 6"vertical laps. Membrane:; Titanium@ PSU-30,self-adhered,with minimum 3"horizontal laps and minimum 6" vertical laps. Place the first course of Titanium@ PSU-30 parallel to the eave and field, j using a heavy pressure roller under safe conditions to further secure the membrane. Surfacing: Approved for asphalt shingle,mechanically fastened roof tile,foam-on roof tile,metal roofing,wood shakes&shingles or slate roof assemblies. Note: For tile roof assemblies,refer to.RAS 118, 119 or 120 and the file manufacturer's NOA. For foam-on tile roof assemblies,approved use with,ICP Adhesives Polyset AH-160 and Dow TILE BOND Roof Tile Adhesive. s I Muar�t�ape courrrir NOA No.:14-0603.19 ■ +,,,� �U Expiration Date:01/26/22 Approval Date:62/02/17 Page 6 of 7 BUILDING PERMIT REQUIREMENTS Application for building permit shall be accompanied by copies of the following: 1. This Notice of Acceptance. 2. Any other documents required by the Building Official or applicable building code in order to properly evaluate the installation of this material. LIMITATIONS 1. Fire;classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. This;acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with applicable building code. 3. Titanium Synthetic Underlayments shall be applied to a smooth, clean and dry surface with deck free of irregularities.All nails in the deck shall be carefully checked for protruding heads. Re-fasten any loose decking panels. Sweep the deck thoroughly to remove any dust.and debris prior to application. 4. Titanium(? UDL-25 PLUS / Titanium@ PSU-30, Titanium@ UDL-30 / Titanium® PSU-30, UDL-MD (2P1y system) / Titanium@ PSU-30 two-ply underlayment system, may be used in asphalt shingle, mechanically fastened roof tile,foam-on roof tile,metal roofing,wood shakes&shingles or slate roof assemblies. 5. The standard maximum roof pitch for the Titanium@ UDL-25 PLUS/TitaniumS PSU-30,Titanium@ UDL-30 /Titanium@ PSU-30,UDL-MD(2P1y system)/Titanium@ PSU-30 two-ply underlayment system shall be 5:12 for flat tiles and 6:,12 on profiled tiles with lugs.for flat file applications at slopes exceeding 5:12, flat tiles shall be staged 2 base tiles perpendicular to slope behind a mechanically attached batten or toe board with maximum 7 tiles high on the slope atop base tiles (Total of stack not to exceed 9 tiles). At roof slopes.greater than the above limitations,the use_of loading battens or toe boards are required to load the roof tile. 6. Titanium Synthetic Underlayments shall not be applied over an existing roof membrane as a recover system. 7. Titanium@ UDL-30/Titanium®PSU-30,Titanium@ UDL-25 PLUS/Titanium@ PSU-30,UDL-MD(2Ply system)/Titanium@ PSU-30 two-ply underlayment system shall not be left exposed as a temporary roof for longer than 90 days of application. S. Titanium Synthetic Underlayments are components used in roof system assemblies.Roof system assemblies are approved under a specific Notice of Acceptance.Refer to Prepared Roofing System Product Control Notice of Acceptance for listed approval of this product with specific prepared roofing products. 9. Titanium Synthetic Underlayments may be used with any approved roof covering Notice of Acceptance listing Titanium Synthetic, Underlayments as a component part of an assembly in the Notice of Acceptance. If Titanium Synthetic Underlayments are not listed, a request may be made to the Authority Having Jurisdiction (AHJ) or the Miami-Dade County Product Control Department for approval provided that appropriate documentation is provided to detail compatibility of the products,wind uplift resistance,and fire testing results. '10. All'membranes or packaging,shall bear the imprint or identifiable marking of the manufacturer's name or logo and.the following statement: "Miami-Dade County Product Control Approved" or the Miami-Dade County Product Control Seal as shown below. M�IA�MI-DADE COUNTY END OF THIS ACCEPTANCE MIAMIDADE COU� NOA No.:14-0603.19 Expiration Date:01/26/22 Approval Date:02/02/17 Page 7 of 7 5 Florida Building Code Online Page 1 of 2 i e i � i � ► �.. � r Q _ BCIS Home ( Log In User Registration Hot Topic Submit Surcharge Stats&Facts € Pub0calions FBC Stag, BCIS Site Map ( Links 4 Search nda r Product Approval iUSER:Public User Sh asQ.ram ! Product Approval Menu>Product or Application Search>Application List>Application Detail - FL# FL10124-R20 Application Type Revision Code Version 2017 Application Status Approved Comments Archived ❑ Product Manufacturer GAF Address/Phone/Email 1 Campus Drive Parisppany,NJ 07054 (800)766-3411 mstieh@gaf.com Authorized Signature Robert Nieminen lindareith@trinityerd.com Technical Representative William Broussard Address/Phone/Email 1 Campus Drive Parsippany,NJ 07054 (800)766-3411 Technica[QuestionsGAF@gaf.com Quality'Assurance Representative Address/Phone/Email Category Roofing Subcategory Asphalt Shingles Compliance Method Evaluation Report from a Florida Registered Architect or a Licensed Florida Professional Engineer ❑ Evaluation Report-Hardcopy Received Florida Engineer or Architect Name who developed Robert Nieminen the Evaluation Report Florida License PE-59166 Quality Assurance Entity UL LLC Quality Assurance Contract Expiration Date 10/20/2018 Validated By John W.Knezevich,PE f ® Validation Checklist-Hardcopy Received Certificate of Independence FL10124 R20 COI 2017 01 COI Nieminen.odf I Referenced Standard and Year(of Standard) Standard Year ASTM D1970 2015 ASTM D3161 2016 ASTM D3462 2010 ASTM D7158 2011 TAS 107 1995 Equivalence of Product Standards Certified By Sections from the Code http://www.floridabuilding.org/pr/pr_app_dtl.aspx?param=wGEVXQwtDquracBeVCbd... 12/14/2017. I I Florida Building Code Online Page 2 of 2 Product Approval Method Method 1 Option D Date Submitted 09/20/2017 Date Validated 09/27/2017 Date Pending FBC Approval 09/28/2017 Date Approved 12/12/2017 Summary of Products FL# Model,Number or Name Description 10124.1 GAF Asphalt Roof Shingles Fiberglass reinforced 3-tab,laminated,5-tab and hip/ridge asphalt shingles Limits of Use Installation Instructions Approved for use in HVHZ:No FL10124 R20 II 2017 09 FINAL ER GAF Asohalt Approved for use outside HVHZ:Yes Shingles FL10124-R20.Ddf Impact Resistant:N/A Verified By;Robert Nleminen PE-59166 Design Pressure:N/A Created by Independent Third Party:Yes Other:Refer to ER,Section 5. Evaluation Reports FL10124 R20 AE 2017 09 FINAL ER GAF Asphalt Shingles FL10124-R20.ndf Created by Independent Third Party:Yes Back Next Contact Us::2601 Blair Stone Road,Tallahassee FL 32399 Phone:850-487-1824 The State of Florida is an AA/EEO employer.Copyright 2007-2013 State of Florida.::Privacy Statement::Accessibility Statement::Refund Statement Under Florida law,email addresses are public records.If you do not want your e-mail address released in response io a public-records request,do not send electronic mail to this entity.Instead,contact the office by phone or by traditional mail.If you have any questions,please contact 850.487.1395.-Pursuant to Section 455.275(1),Florida Statutes,effective October 1,2012,licensees licensed under Chapter 455,F.S.must provide the Department with an email address if they have one.The emails provided may be used for official communication with the licensee.However email addresses are public record.If you do not wish to supply a personal address,please provide the Department with an email address which can be madeavailable to the public.To determine If you are a licensee under Chapter 455,F.S.,please click here. Product Approval Accepts: W®� �'if@d1C CiafC� Safes y http://www.floridabuilding.org/pr/pr app_dtl.aspx?param=wGEVXQwtDquracBeVCbd... 12/14/2017 EXTERIOR RESEARCH&DESIGN,I.I.C. Certificate of Authorization#9503 CDp TRINITY ERD 353 CHRISTIAN OXFORD,STREET, UNIT CT 06478478 (203)262-9245 EVALUATION REPORT GAF Evaluation Report 01506.01.08-1122 1 Campus Drive FL10124-1120 Parsippany,NJ 07054 Date of Issuance:01/03/2008 (800)766-3411 Revision 22:09/20/2017 SCOPE: I This Evaluation Report'is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen, P.E:for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have•been evaluated for compliance with the 6th Edition (2017) Florida Building Code sections'noted herein. DESCRIPTION: GAF Asphalt Roof Shingles LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein and FBC 1507.2.7.1/R905.2.6.1. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen,P.-E. if the product'changes or the referenced Quality Assurance documentation changes. TrinitylERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT:The Evaluation Report number preceded by the words "Trinityl ERD Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety. INSPECTION:Upon request,a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 6. Prepared by: - �2 C©y�7-5?1fi6J•i S Robertl.M.Nieminen,P.E. The facsimile seal appearing was authorized byRobert Nteminen, Rtfll Florida Registration No.59166,Florida DCA ANE1983 4 P.E.on 09/20/2017.This does not serve as an electronically signed document CERTIFICATION OF INDEPENDENCE: 1. Trinity IERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Trinityl ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates. 3. Rob'e'rt Nieminen,P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the product. S. This is a building code evaluation. Neither TrinitylERD nor Robert Nieminen; P.E. are, in any way,the Designer of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained specifically for that purpose. i TRINITY`ERD ROOFING'SYSTEMS EVALUATION: 1. SCOPE: Product Category: Roofing Sub-Category: Asphalt Shingles Compliance Statement: GAF Asphalt Roof Shingles, as produced by GAF,have demonstrated compliance with the following sections of the 6th Edition (2017) Florida Building Code and Florida Building Code, Residential Volume through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations/Conditions of Use set forth herein. 2. STANDARDS: Section Property Standard Year 1507.2.4/1507.1.1, Physical Properties ASTM D1970 2015 R905.2.3/R905.1.1 1507.2.5,R905.2.4 Physical Properties ASTM D3462 2010 1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2016 1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2011 1507.2.7.1,R905.2.6.1 Wind Resistance TAS 107 1995 3. REFERENCES: Enti Examination Reference Date GAF(PDM 1915) Letter of Equivalency 1 Seal-A-Ridge Impact Resistant IR 01/13/2012 PRI(TST 5878) Physical Properties GAF-025-02-01 03/27/2002 PRI(TST 5878) ASTM D3462 GAF-059-02-01 09/02/2004 PRI(TST 5878) ASTM D3462 GAF-080-02-01 05/25/2005 PRI(TST 5878) Physical Properties GAF-324-02-01 12/01/2011 PRI(TST 5878) Wind Driven Rain GAF-407-02-01 01/21/2013 UL(TST 1740) ASTM D3462 93NK6295 11/29/1993 UL(TST 1740) ASTM D3462 99NK43835 01/12/2000 UL(TST 1740) TAS 107 94NK9632 03/29/2000 UL(TST 1740) ASTM D3462 01NK06632 02/02/2001 UL(TST 1740) ASTM D3161,TAS 107 01NK9226 05/21/2001 UL(TST 1740) ASTM D3161 OINK37122 12/18/2001 UL(TST 1740) ASTM D3462 OINK37122 12/19/2001 UL(TST 1740) ASTM D3161,TAS 107 02NK12980 04/10/2002 UL(TST 1740) ASTM D3161,TAS 107 02NK30871 09/09/2002 UL(TST 1740) ASTM D3161 03CA5367 03/11/2003 UL(TST 1740) ASTM D3462 03NK26444 10/17/2003 UL(TST 1740) ASTM D3462 04NK13850 06/07/2004 UL(TST 1740) ASTM D3161 04NK13850 06/23/2004 UL(TST 1740) ASTM D3161 04NK30546 03/10/2005 UL(TST 1740) ASTM D3462 04NK22009 05/06/2005 UL(TST 1740) ASTM D3161 04NK22009 05/09/2005 UL(TST 1740) ASTM D3462 05NK27924 02/10/2006 UL(TST 1740) ASTM D3161 65NK27924 02/11/2006 UL(TST 1740) ASTM D3161,D3462 06CA18077 06/05/2006 UL(TST 1740) ASTM D3161,D3462 06CA18074 06/16/2006 UL(TST 1740) ASTM D3161,D3462 06CA35251 10/18/2006 UL(TST 1740) ASTM D3462 06CA31603 12/01/2006 UL(TST 1740) ASTM D3161,D3462 06CA41095 12/27/2006 UL(TST 1740) ASTM D3161 07NK05228 03/13/2007 UL(TST 1740) ASTM D3161 06CA31611 04/04/2007 UL(TST 1740) ASTM D3161 06CA61148 04/09/2007 UL(TST 1740) ASTM D3161,D3462 07CA31742 11/08/2007 UL(TST 1740) ASTM D3161,D7158,D3462 08CA06100 03/13/2008 Exterior Research and Design,I.I.C. Evaluation Report 01506.01.08-R22 Certiflcote ofAuthorization#9503 GP EDITION(2017)FBC NON-HVHZ EVALUATION F1.10124-1120 GAF Asphalt Roof Shingles Revision 22:09/20/2017 Page 2 of 6 (-)o TRINITY I ERD Enti Examination Reference Date UL(TST 1740) ASTM D3161,D3462 07CA55908 04/01/2008 UL(TST 1740) ASTM D3161,D3462 09CA10592 03/26/2009 UL(TST 1740) ASTM D3161,D3462 09CA06856 05/15/2009 UL(TST 1740) ASTM D3161,D7158,D3462 09NK06647 08/01/2009 UL(TST 1740) ASTM D3161,D7158,D3462 09CA27281 08/27/2009 UL(TST 1740) ASTM D3161,D7158,D3462 IOCA35554 03/05/2010 PL(TST 1740) ASTM D3161,D7158,D3462 10CA13686 05/15/2010 UL(TST 1740) ASTM D3462 IOCA07264 05/27/2010 UL(TST 1740) ASTM D3462 1OCA11653 10/29/2010 UL(TST 1740) ASTM D3161,D7158,D3462 IONK11951 10/30/2010 UL(TST 1740) ASTM D3161,D7158,D3462 IONK12070 11/04/2010 UL(TST 1740) ASTM D3161,D7158,D3462 08CA06100 01/30/2010 UL(TST 1740) ASTM D3161,D7158,D3462 IOCA53934 03/31/2011 UL(TST 1740) ASTM D3161,D7158,D3462 11CA48924 10/22/2011 UL(TST 1740) ASTM D3161,D7158,D3462 11CA47919 12/03/2011 UL(TST 1740) ASTM D3161,D7158,D3462 11CA48408 12/08/2011 UL(TST 1740) ASTM D3161,D7158,D3462 11CA48725 12/09/2011 UL,I.I.C.(TST 9628) ASTM D3462 12CA34891 10/12/2012 UL,LLC.(TST 9628) ASTM D3161,D7158,D3462 12CA58151 02/15/2013 UL,LLC.(TST 9628) ASTM D3161 12CA38083 02/26/2013 OL,LLC.(TST 9628) ASTM D3161 13CA32332 06/18/2013 UL,LLC.(TST 9628) ASTM D3161 13CA37934 08/02/2013 UL,I.I.C.(TST 9628) ASTM D3161,D7158,D3462 4786875675 07/17/2015 UL,LLC.(TST 9628) ASTM D3161,D7158,D3462 4787434542 05/17/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Mobile,AL 10/25/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Myerstown,PA 10/20/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Tuscaloosa,AL 11/11/2016 UL,I.I.C.(QUA 9625) Quality Control Inspection Report,R21,Michigan Cty,IN 11/01/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Shafter,CA 11/17/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report, R21,Savannah,GA 11/11/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Minneapolis,MN 10/25/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Mt.Vernon,IN 10/25/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Baltimore,MD 10/21/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Tampa,FL 11/17/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Dallas,TX 11/04/2016 UL,LLC.(QUA 9625) Quality Control Inspection Report,R21,Ennis,TX 11/03/2016 UL,LLC.(QUA 9625) Quality Control Inspection Repoft,R21,Fontana,CA 11/01/2016 4. PRODUCT DESCRIPTION: 4.1 Asphalt Shingles: 4.1.1 Marquis® WeatherMax", Royal Sovereign® and Sentinel® are a fiberglass reinforced 3-tab asphalt roof shingles. 4.1.2. Camelot®, Camelot® II, Fortitude'", Glenwood"m" Grand Canyon®, Grand Sequoia®, Grand Sequoia® IR, Grand Sequoia® ArmorShield TM, Monaco®, Sienna®, Timberline® American Harvest®, Timberline° ArmorShield"' II,Timberline® Natural Shadow®,Timberline HD®,Timberline®Cool Series®,Timberline Ultra HD®and Woodland®are fiberglass reinforced,laminated asphalt roof shingles. 4.1.3 Slateline®is a fiberglass reinforced 5-tab asphalt roof shingle. 4.2 Hip&Ridge Shingles: 4.2.1 Seal-A-Ridge® Ridge-Cap Shingles, Seal-A-Ridge® IR Impact-Resistant Ridge Cap Shingles, Seal-A-Ridge® ArmorShield'" Ridge Cap Shingles and Timbertex® Premium Ridge Cap Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles. Exterior Research and Design,LLC. Evaluation Report 01506.01.08-R22 Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION F1.10124-1120 GAF Asphalt Roof Shingles Revision 22:09/20/2017 Page 3 of 6 TRINITY ERD 4.3 Accessory Starter Strips: 4.3.1 Pro-Start®Eave/Rake Starter Strip Shingles and WeatherBlocker''Premium Eave/Rake Starter Strip Shingles are starter strips for asphalt roof shingles. 4.3.2 QuickStart° Peel & Stick Starter Roll is a is a mineral-surfaced, fiberglass-reinforced, self-adhering SBS modified bitumen starter strip,nominal 9-inch x 33 ft roll,for use with asphalt shingles with exposure of 6- inch or less. 4.3.3 StarterMatch1m Starter Strip Shingles are color-coordinated starter strips for use with Grand Canyon® and Grand Sequoia° series asphalt shingles. StarterMatchTm are installed as the second starter for Grand Canyon®and Grand Sequoia®series installations. S. LIMITATIONS: 5.1 This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was Used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions. 5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire ratings of this product. 5.4 Wind Classification: 5.4.1 The GAF asphalt shingles noted in Section 4.1 are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158,Class H,indicating the shingles are acceptable for use in all wind zones up to Vasd=150 mph(V„It=194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.2 The GAF hip&ridge shingles noted in Section 4.2 are Classified in accordance with FBC Tables 1507.2.7.1 and R9012.6.1 to ASTM 133161,Class F, indicating the shingles are acceptable for use in all wind zones up to Vasd=150 mph(Vult=194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.3 Classification by ASTM D7158 applies only to exposure category B or C, as defined in FBC 1609.4.3,and a mean roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. 5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C.Rule 61G20-3. 6. INSTALLATION: 6.1 Underlayment: 6.1.1 Underlayment shall be acceptable to GAF and shall hold current Florida Statewide Product Approval, or be Locally Approved per Rule 61G2&-3,-per FBC 1507.2.3,1507.2.4 or R905.2.3. 6.2 Starter Shingles.or Starter Stria: 6.2.1 Installation of Pro-Start Eave/Rake Starter Strip Shingles,WeatherBlocker Premium Eave/Rake Starter Strip Shingles and QuickStart Peel&Stick Starter Roll shall comply with the GAF current published instructions. I 6.3 Asphalt Shingles: 6.3.1 Installation of asphalt shingles shall comply with the GAF current published instructions,using minimum four (4)nails per shingle in accordance with FBC 1507.2.7 or R905.2.6,with the following exceptions: ➢ Camelot, Camelot II, Grand Canyon, Grand Sequoia, Grand Sequoia IR, Grand Sequoia ArmorShield, and Woodland require minimum five(5)nails per shingle. ➢ Slateline requires minimum six(6)nails per shingle. 6.3.2 Fasteners shall be in accordance with manufacturer's published requirements,but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.3.3 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required..Contact the GAF for details. Exterior Research and Design,LLC. Evaluation Report 01506.01.08-1122 Certificate of Authorization#9503 6n'EDITION(2017)FBC NON-HVHZ EVALUATION F1.10124-1120 GAF Asphalt Roof Shingles Revision 22:09/20/2017 Page 4 of 6 Q TRINITY f ERD 6.4 Hip&Ridge Shingles: 6.4.1 Installation of Seal-A-Ridge Ridge Cap Shingles, Seal-A-Ridge IR Impact-Resistant Ridge Cap Shingles and Seal-A-Ridge ArmorShield Ridge Cap Shingles shall comply with the GAF current published instructions with a minimum two (2) nails, minimum 3/8-inch head diameter, per shingle and nominal 0.25-inch diameter beads of Henkel"Loctite PL S30 Roof&Flashing Sealant". 11.5b Sealant 1 (292 mm) 1' 1 %lame. {25,mm} (25 mm) E6du'it'd'6tanch6R6 � ti,�,' x � (305 mm) Nair Glavo. 6 518":-7518° Glouer (968-194 mm), 12 (305.min) � 6.4.2 Installation of Timbertex Premium Ridge Cap Shingles shall comply with GAF current published instructions with a minimum two (2) nails, minimum 3/8-inch head diameter,per shingle and beads of Sonneborn NP1 Gun Grade Polyurethane Sealant or Henkel PL Roofing and Flashing Sealant. 1 " '�-{2E�2 nSn1f 4" Sul P2 r�rna [g5 rA Grt ittrint t ►tv I s i NOV t� Vow kt1S rtxtt) 6" MM) 6.4.3 Fasteners shall be in accordance with GAF published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. i i Exterior Research and Design,U.C. Evaluation Report 01506.01.08-1122 Certfcate of Authorization#9503 6'"EDITION(2017)FBC NON-HVHZ EVALUATION F1.10124-1120 GAF Asphalt Roof Shingles Revision 22:09/20/2017 Page 5 of 6 t TRINIW I ERD .7. •LABELING: 7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. 7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC Table 1507.2.7.1/R905.2.6.1. 8. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 9. MANUFACTURING PLANTS: Contact the named QA entity for information on which plants produce products covered by Florida Rule 611320-3 QA requirements. 10. QUALITY ASSURANCE ENTITY: UL LLC—QUA9625;(847)664-3281 END OF EVALUATION REPORT- i I { i j i j i Exterior Research and Design,I.I.C. Evaluation Report 01506.01.08-1122 Certificate ofAathorization#9503' 6'"EDITION(2017)FBC NON-HVHZ EVALUATION FL10124R20 GAF Asphalt Roof Shingles Revision 22:09/20/2017 Page 6 of 6