HomeMy WebLinkAboutProduct Approval, windows, fixedDEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
NOTICE OF ACCEPTANCE (NOA)
CGI Windows and Doors, Inc.
3780 W 104 Street
Hialeah, FL 33018
MIAMI—DADE COUNTY, FLORIDA
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599.
�.miamidade0
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER -
Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority
Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control
Section (In Miami -Dade County) and/ or the AHJ (*in areas other than Miami -Dade County) reserve the right
to have this product or material tested for quality assurance purposes. If this product or material fails to
perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may
immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER
reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control
Section that this product or material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building
Code, including the High Velocity Hurricane Zone.-
DESCRIPTION: Series "Sentinel 130" Aluminum Fixed Window — L.M.I.
APPROVAL DOCUMENT: Drawing No. PW130LMI-NOA, titled "Sentinel 130 Alum Fixed Window
(L.M.I.)(S.M.I.)` sheets 1 through 7 of 7, dated 05/22/19, prepared by manufacturer, signed and sealed by
Anthony Lynn Miller, P.E., bearing the Miami -Dade County Product Control Revision stamp with the
Notice of Acceptance number and expirati
Non date by the Miami -Dade County Product Control Section.
Large
MISSILE IMPACT RATING:
LABELING: Each unit shall bear a
and Small Missile Impact Resistant
permanent label with the manufacturer's name or logo, city, state,
series, and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted
herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been
no change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change.
in the materials, use, and/ or manufacture of the product or process. Misuse of this NOA as an endorsement
of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure
to comply with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and
followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is
displayed, then it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA No. 174918.07 and consists of this page 1 and evidence pages E-1, E-2, E-3 and
E4, as well as approval document mentioned above.
The submitted documentation was reviewed by Manuel Perez, P.E.
NOA No. 19-0603.02
Expiration Date: September 22,.2020
Approval Date: July 03, 2019
Page 1
CGI Windows and Doors, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA's
A. DRAWINGS
1. Manufacturer's die drawings and sections.
(Submitted under NOA No. 104510.13)
2. Drawing No. W10-02, titled "Series Sentinel 130 Alum Fixed Window (L.M.I.)
(SOM016) sheets 1, 1.1, 2, 3, 4, 5 and 6 of 6, dated 01 /3 0/ 10, with revision G, dated
08/29/17, prepared by Al-Farooq Corporation, signed and sealed by Javad Ahmad,
P.E.
(Submitted under NOA No.17-0918.07)
B. TESTS
1.
Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
2) Large Missile Impact Test per FBC, TAS 201-94
3) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of a series 7500 PVC fixed
W1ndOW, to qualify DuPont "Butacite" PVB interlayer, Duraseal® and Super Space
insulating glass spacer, prepared by Certified Test Laboratories, Test Report No.
CTLA-3056 WA, dated 03/03/15, signed and sealed by Ramesh C. Patel, P.E.
(,Submitted under NOA No. 15-0413.03)
Test reports on: 1) Uniform Static Air , Pressure Test, Loading per FBC TAS 202-94
2) Large Missile Impact Test per FBC, TAS 201-94
3) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of a series 7400 PVC project
out window, to qualify DuPont "Butacite" PVB interlayer, Duraseal® and Super
Spacer(V insulating glass spacer, prepared by Certified Test Laboratories, Test Report
No. CTLA-3056 NM,, dated 03/03/155 signed and sealed by Ramesh C. Patel, P.E.
(Submitted under NOA No.15-0413.03)
Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
2) Large Missile Impact Test per FBC, TAS 201-94
3) Cyclic Wind Pressure Loading per, FBC, TAS 203-94
along with marked -up drawings and installation diagram of a series 238 aluminum
fixed window, to qualify DuPont "Butacite" PVB interlayer, ® Durasealand Super
Spacer® insulating glass spacer, prepared by Certified Test Laboratories, Test Report
No. CTLA-3056 WC, dated 04/16/15, signed and sealed by Ramesh C. Patel, P.E.
(Submitted under NOA No. l 54413.03)
E-1
Manuel P E.
Product Control za ner
NOA No. 1 03.02
Expiration Date: September 22, 2020
Approval Date: July 03, 2019
CGI Windows and Doors, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
B. TESTS �coNTIlVUED�
4. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94
2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
3) Water Resistance Test, per FBC, TAS 202-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of a Sentinel 13 0 aluminum
fixed window, prepared by Hurricane Test Laboratory,. Test Report No.
HTL-0080-0130-10, dated 03/30/10, signed and sealed by Vinu J. Abraham, P.E.
(Submitted under NOA No. 10-0510.13)
C. CALCULATIONS
1. Anchor verification calculations and structural analysis, complying with FBC 6th
Edition (2017), dated July 15, 2017, prepared by Al-Farooq Corporation, signed and
sealed by Javad Ahmad, P.E.
(Submitted under NOA No.17-0918.07)
2. Glazing complies with ASTM E1300-09.
D. QUALITY ASSURANCE _
1. Miami -Dade Department of Regulatory and Economic Resources (RER)
E. MATERIAL CERTIFICATIONS
1. Notice of Acceptance No. 14-0916.11 issued to Kuraray America, Inc. for their
"SentryGlas® (Clear and White) Glass Interlayers" dated 06/25/15, expiring on
07/04/18.
2. Notice of Acceptance No. 16-1117.01 issued to Kuraray America, Inc. for -their
"Trosifol® Ultraclear, Clear and Color PVB Interlayers" dated O1/19/17, expiring
on 07/08/19.
3. Notice. of Acceptance. No. 17-0712.03 issued to Eastman Chemical:.Company (VIA) .
for their "Saflex CP —Saflex and Saflex HP Composite Glass Interlayers with _
PET C-ore" dated 09/07/ 17, expiring on 12/ 11 / 18 . .-
4. Notice of Acceptance No. 17-0712.05 issued to Eastman Chemical Company (VIA)
for their "Saflex Clear and Color Glass Interlayers" dated 09/07/17, expiring on
OS%21/21.
F. STATEMENTS
1. Statement letter of conformance, of complying with FBC 5th Edition (2014), with
FBC 6th Edition (2017) and of no financial interest, dated August 15, 2017, issued by
Al-Faxooq Corporation, signed and sealed by Javad Ahmady P.E.
(Submitted under NOA No.17-0918.07)
Manue a z, P.E.
Product Con of aminer
NOA 9-0603.02
Expiration Date: September 22, 2020
Approval Date: July 03, 2019
E-2
CGI Windows and Doors, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
F. STATEMENTS �cONTIlVUED)
2. Laboratory compliance letter for Test Report No. HTL-0080-010340, issued by
Hurricane Test Laboratory, LLC, dated March 3 0, 2010, signed and sealed by Vinu J.
Abraham, P.E.
(Submitted under NOA No.104510.13)
3. Test Proposal for the qualification of Butacite® PVB glass interlayer by Kuraray
America, Inc., as well as Duraseal® and Super Spacer@ Standard warm -edge
flexible insulating glass spacers, dated December 16, 2014, issued by RER, Product
Control Section, signed by Jaime Gascon, P.E., Supervisor, Product Control Section.
(Submitted under NOA No. 154413. 03)
G. OTHERS
1. Notice of Acceptance No. 154413.03, issued to CGI Windows & Doors, for their
Series "Sentinel 130" Aluminum Fixed Window — L.M.I. approved on 06/25/15 and
expiring on 09/22/20.
2. NEW EVIDENCE SUBMITTED
A. DRAWINGS
1. Drawing No. PW130LMI-NOA, titled "Sentinel 130 Alum Fixed Window
(L.M.I.)(S.M.I.)
", sheets 1 through 7 of 7, dated 05/22/19, prepared by manufacturer,
signed and sealed by Anthony Lynn Miller, P.E.
B. TESTS
1. Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94
2) Large Missile Impact Test per FBC, TAS 201-94
3) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of a series 560 aluminum
sliding glass door, prepared by Fenestration Testing Laboratory, Inc., Test Report No.
FTL494916, dated 04/10/19, signed and sealed by Idalmis Ortega, P.E.
2. Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94
2) Water Resistance Test, per FBC, TAS 202-94
3) Small Missile Impact Test per FBC, TAS 201-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked -up drawings and installation diagram of a series 13 0 and 410
aluminum fixed windows, prepared by Fenestration Testing Laboratory, Inc., Test
Report No. FTL49-8917, dated 04/09/19, signed and sealed by Idalmis Ortega, P.E.
v Product Co rol E miner
NOA-0603.02
Expiration Date: September 22, 2020
Approval Date: July 03, 2019
E-3
CGI Windows and Doors, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
C. CALCULATIONS
1. None
D. QUALITY ASSURANCE
1. Miami -Dade Department of Regulatory and Economic Resources (RER)
E. MATERIAL CERTIFICATIONS
1. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their
"SentryGlas® (Clear and. White) Glass Interlayers" dated 12/28/17, expiring on
07/04/23. -
2. Notice of Acceptance No. 17-1114.14 issued to Kuraray America, Inc. for their
"Trosifol® Ultraclear, Clear and Color PVB Glass Interlayers" dated O1/18/18,
expiring on 07/08/19.
3. Notice of Acceptance No. 18-0301.06 issued to Eastman Chemical Company (VIA)
for their "Saflex CP - Saflex and Saflex HP Composite Glass Interlayers with PET
Core" dated OS/17/18, expiring on 12/11/23.
Notice of Acceptance No. 17-0712.05 issued to Eastman Chemical Company (VIA)
for their "Saflex Clear and Color Glass Interlayers
OS/21/21.
" dated 09/07/ 17, expiring on
F. STATEMENTS
1. Statement letter of conformance, complying with FBC 6t'' Edition (2017), dated May
23, 2019, issued by manufacturer, signed and sealed by A. Lynn Miller, P.E.
2. Statement letter of no financial interest, dated May 23, 2019, issued by manufacturer,
signed and sealed by A. Lynn Miller, P.E.
3. Proposal No. 19-0219 issued by the Product Control Section, dated March 13, 2019,
signed by Ishaq Chanda, P.E..
4. Notification of Successor Engineer for manufacturer's NOA document per Section
61G15-27.001 of the Florida Administrative Code, notifying original engineer that
the successor engineer is assuming full professional and legal responsibility for all
engineering documents pertaining to this NOA, dated May 22, 2019, signed and sealed
by A. Lynn Miller, P.E.
G. OTHERS
1. Notice of Acceptance No. 17-0918.07, issued to CGI Windows and Doors, Inc. for
their Series "Sentinel 130" Aluminum Fixed Window -L.M.I. approved on 11/22/17
and. expiring on 09/22/20.
Manuel"Per .E.
Product Control xa ner
NOA No. 1 - 3.02
Expiration Date: September 22, 2020
Approval Date: July 03, 2019
E-4