HomeMy WebLinkAboutProject Information, Generator InterlockModel
Main Breaker
Generator Breaker
EAT-CH2O0A Pat. l
150 or 200 amp sing
Tote left side 2 Dositi
handle Horizontal throw left (on) to
WARNING
Only qualified personnel should be working on the panel box
An amateur should NEVER open the panel box
Please follow all rules and regulations of the National Electric Code
Step 1: Disassemble the interlock. Place the bottom plate (holes only) above the top left breaker and mark holes. Plate is parallel to
left top breaker and touches the edge of the right top breaker.
Step 2: Turn off main breaker and remove panel cover.
Step 3: Drill holes as marked on panel cover with supplied 3/16 drill bit and remove all burs from drilling cover.
Step 4: Insert screws from rear of cover, install bottom plate, and install top plate (slotted) install tread lock to screws and install
retaining nuts. Ensure proper movement.
Step 5: Install 2 pole Generator breaker on top left side and place Generator Warning Sticker on Generator breaker.
Step 6: Combine the zip ties to make a loop and install zip ties around top set of breakers in panel as shown in picture below. Pull on
ends to make tight around breakers. Trim zip ties as needed and Install Warning label next to release tab on zip tie at
Step 7: Re -Install panel cover, Verify proper operation of interlock. Main breaker ON, generator breaker OFF and generator breaker
CAN NOT be turned on. Generator breaker ON, main breaker OFF and main breaker CAN NOT be turned on. Please
touching all breaker, if not adjust panel cover with to and bottom screw on cover.
Main On
Generator On
Step 8: Place Generator start-up procedure label on panel box, Place CAUTION label on panel box and electric meter pan.
The MAIN and the GENERATOR breakers should NEVER be able to be turned on at the same time. If panel cover is removed the
Generator breaker is NEVER to be turned on. If for any reason the interlock does not function properly, DO NOT USE and contact us
immediately at sales(k6enInterlock.com for support and instructions.
Thank You for your support,
GenInterlock Team
DISCLAIMER: Genlnterlock.com is NOT responsible for misuse or improper installation. All electrical
equipment should be installed and maintained by qualified personnel. Any consequences arising from improper
use is the responsibility of the user.
GenInterlock.com
2227 US Highway 1 — Unit 124
North Brunswick, NJ 08902
Sales eninterlock.com
732-3394191
1. Power Inlet Box
Description: Indoor/Outdoor Power Inlet Receptacle. Provides the means for getting
Electricity from your portable generator to your manual transfer switch
Catalog Numbers Dimensions li•,l
weight Amperage
Receptacle
Veltoe
(lI![ RD)
(tii5.1 %ting
Configuration
fGSPI820 l 6.X fix 5
20
04-20
120 L40, Smie lease
5 i_6 x 61 5
! 3f1
t,4-
t #24f1. 5i 1e Riase
Features & Benefits
• Indoor/Outdoor installation
• Good for: Generators, RV Hook-ups, Tool Inlet Box
• Padlockable
• In use cover
• Surface Mount
• Easy to install. Easy to use.
• 15 year Warranty
Technical Information
• UL Listed
• 120/240 Vac
• 20A, 1PH-3W
• L 14-20 and L 14-30 Receptacles
• NEMA 3R rated Enclosure
Marketing
Why buy an EATON Power Inlet Box?
• A Name YOU can trust — EATON has been powering homes and business
worldwide for over than 100 years. We know Power — and how to use it more
efficiently.
• SAFE, Easy -To -Use, Cost Effective. If power goes out, you may loose more
than just a few lights. Eaton's Power Inlet Receptacle provides with a low cost,
safe, easy -to -use way to plug your portable generator power system.
0 24/7 Technical Support. Need Help? Our Eaton's Generator Support Center is
available to assist you with any technical/installation questions you might have.
Just dial 1(800) ETN-CARE (386-2273). Assistance is FREE
• 3.5 Million People across the US experience power outages each week. Don't be
one of them. Eaton's Power Inlet Receptacle is the solution for your back-up
power needs!
For more information about our products and services, visit our website:
www.eaton.com