HomeMy WebLinkAboutProduct Approval (2) • File COPY
9tvEWE® FOR
RECEIVE® CODE COMPLIANCENEMO I etc.
Authorization#32455
SEP 2 7 ?019 ��° �—���� s et, Unit#13
®!�� e ford,CT 06478
ST. Lucie County, Permitting (203) 262-9245
ENGINEER EVALUATE TEST CONSULT CERTIFY
REPORTEVALUATION
Owens Corning Evaluation Report 037940.02.12-119
One Owens Corning Parkway FL10674-1114
Toledo,OH 43659 Date of Issuance:02/06/2012
(740)404-7829 Revision 9: 06/13/2019
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen,
P.E.for use of the product under the Florida Building Code and Florida Building Code,Residential Volume. The products
described herein have been evaluated for compliance with the 6th Edition(2017)Florida Building Code sections noted
herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted
herein and FBC 1507.2.7.1/R905.2.6.1
CONTINUED COMPLIANCE: This Evaluation Report is valid until the named product(s) changes, the referenced Quality
Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this
Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. of any changes to the
product(s),the Quality Assurance or the production facility location(s). NEW I etc. requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "NEMO I etc. Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
i
This Evaluation Report consists of pages 1 through 10.
Prepared by:
-dry
Robert J.M.Nieminen P.E. %�,�,',q:�s :.•• The facsimile seal appearing was authorized by Robert
r '.;cSy f�• c' Nieminen,P.E.on 06/13/2019.This does not serve as an
Florida Registration No.59166,Florida DCA ANE1983 ";?'r�..°`.���'•`' electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. NEMOJetc. does not have, nor does it intend to acquire, or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEW I etc.is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen,P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
` S. This is a building code evaluation. Neither NEMO I etc.nor Robert Nieminen,P.E.are,in any way,the Designer of Record for any project
on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained specifically
for that purpose.
ONEMOletc.
ROOFING SYSTEMS EVALUATION:
Product Category: Roofing
Sub-Category: Asphalt Shingles
Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning, have
demonstrated compliance with the following sections of the 6a'Edition(2017)Florida Building Code and Florida
Building Code, Residential Volume through testing in accordance with the following Standards. Compliance is
subject to the Installation Requirements and Limitations/Conditions of Use set forth herein.
STANDARDS:2.
Section Pro a ,_ Standard Year
1507.2.4,R905.2.3 Physical Properties ASTM D1970 2015
1507.2.5,R905.2.4 Physical Properties ASTM D3462 2010
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D3161 2016
1507.2.7.1,R905.2.6.1 Wind Resistance ASTM D7158 2011
3. REFERENCES:
Enti Examination Reference Date
_._. .._. _..._.. _.. _., .. .. .,
PRI(TST5878) ASTM D1970 OCF-382-02-01 10/24/2017
UL LLC(CER9626) Physicals&Wind Resistance File R2453,Vol.3 02/15/2007
UL LLC(CER9626) Physicals&Wind Resistance 20120516-R2453 05/16/2012
UL LLC(TST9628) Physical Properties 06CA20263 04/18/2006
UL LLC(TST9628) Wind Resistance 11CA34308 02/18/2012
UL LLC(TST9628) Physicals&Wind Resistance 4786093137 02/01/2014
UL LLC(TST9628) Wind Resistance 4786126532 02/10/2014
UL LLC(TST9628) Physical Properties Classification letter 02/13/2014
UL LLC(TST9628) Physical Properties Classification letter 10/02/2015
Miami-Dade(CER1592) FBC HVHZ Compliance Various NOAs Various
PRI(QUA9110) Quality Control Service Confirmation 04/05/2020
4. '••• DESCRIPTION:
4.1 ACCESSORYSTARTERS: 71
4.1.1 Starter StripShingle and Starter Strip Plus are start* a ,,
g p r strips for asphalt roof shingles. Meets ASTM D3462.
4.1.2 Starter Shingle Roll is a mineral-surfaced,fiberglass-reinforced,self-adhering SBS modified bitumen starter strip,
nominal 7.2-inch wide x 33-ft 4-inch long roll,for use with asphalt shingles. Meets ASTM D1970.
ASPHALT SHINGLES.� o ` '
4.2.1 Classic and Supreme are fiberglass reinforced,3-tab asphalt roof shingles.Meets ASTM D3462.
4.2.2 Berkshire*are fiberglass reinforced,4-tab asphalt roof shingles. Meets ASTM D3462.
j 4.2.3 Duration*,TruDefinition* Duration*, Duration'Premium Cool,TruDefinition®Duration*Designer Color Collection,
TruDefinition*Oakridge, Oakridge* and WeatherGuard* HP are fiberglass reinforced, laminated asphalt roof
shingles. Meets ASTM D3462.
HIP&R'1bGE SHINGLES:..
4.3.1 Berkshire*Hip&Ridge Shingles with Sealant,DuraRidge®Hip&Ridge Shingles with Sealant,ProEdge®Hip&Ridge
Shingles and WeatherGuard*HP Hip&Ridge Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles.
Meets ASTM D3462.
NEMO ETC,LLC Evaluation Report 037940.02.12-R9
Certificate of Authorization#32455 9-EDITION(2017)FBC NON-HVHZ EVALUATION F1.10674-1114
Owens Corning Asphalt Roof Shingles Revision 9:06/13/2019
Page 2 of 10
ONEMOletc.
LIMITATIONS:5.
5.1 This is a building code evaluation. Neither NEMO ETC,LLC nor Robert Nieminen,P.E.are,in any way,the Designer
of Record for any project on which this Evaluation Report,or previous versions thereof,is/was used for permitting
or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for
fire ratings of this product.
5.4 Wind Classification:
5.4.1 The Owens Corning asphalt shingles noted in Section 4.2 are Classified in accordance with FBC Tables 1507.2.7.1
and R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158,Class H, indicating acceptable use in all wind zones
up to Vasd=150 mph(Vult=194 mph). Refer to Section 6 for installation requirements to meet this wind rating.
Note: Classification by ASTM D7158 applies only to exposure category B or C,as defined in FBC 1609.4.3, and a
mean roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions
outside these limitations. Contact the shingle manufacturer for data specific to each shingle.
5.4.2 Starter Strip Shingle and Starter Strip Plus noted in Section 4.1.1 and the Owens Corning hip&ridge shingles noted
in Section 4.3 are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F,
indicating acceptable use in all wind zones up to Vasd=150 mph(Vult=194 mph). Refer to Section 6 for installation
requirements to meet this wind rating.
5.4.3 Refer to Owens Corning published information on wind resistance and installation limitations.
5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C.Rule 61G20-3.
6. INSTALLATION:
6 1 GENERAL
6.1.1 Roof deck, slope, underlayment and fasteners shall comply with FBC 1507.2 / R905.2 and the shingle
manufacturer's minimum requirements.
6.1.2 Underlayment shall be acceptable to the shingle manufacturer and shall hold current Florida Statewide Product
Approval,or be Locally Approved per Rule 61G20-3,per FBC Sections 1507.2.3,1507.2.4 or R905.2.3.
6.1.3 Fasteners shall be in accordance with the shingle manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.1.4 Owens Corning asphalt shingles are acceptable for use in reroof(tear-off)or recover applications,subject to the
limitations set forth in FBC Section 1511 or R908 and published installation instructions.
6 2 ACCESSORY STARTERS
6.2.1 instructions,using using minimum five(5)nails per strip.
Felt r
Plus shall comply with the Owens Corning current published
Fdtrmdulaynient Deck w andaure.ar t>e<k wt.r a ed
SeU adhtred. Wwalam
WeatherLocN
tmdo ayawnt (
Drip edpa _
��0e
e
Na1s loafed °
Ya°'fromoars Y 3 hamem
hMas fast SaEseafmg adhesive edeshe
Starterstr'� positioned along eave wMcra or �aMgave
shmcle with -..
6°removed StarttaS*shingle ovedunpssam and rakesW4 Sunee P6 —1t1aK M—Wr*K114 dW
Figure 1:Minimum Nailing,Starter Strip Figure 2:Minimum Nailing,Starter Strip Plus
NEMO ETC,LLC Evaluation Report 037940.02.12-R9
Certificate of Authorization N32455 0 EDITION(2017)FBC NON-HVHZ EVALUATION F1.10674-1114
Owens Corning Asphalt Roof Shingles Revision 9:06/13/2019
Page 3 of 10
fONEMOjetc.
6.2.2 Installation of Starter Shingle Roll shall comply with the Owens Corning current published instructions.
Deck
Underlayment
Drip edge s,d
Drip edge
E SJ f.
Starter Shingle Roll adhered
4
directly to underlayment and
primed drip edge
Self-sealing adhesive
positioned along eaves
Figure 3:Starter Shingle Roll
6 , ASPHALT SHINGLES:
6.3.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using
minimum four(4)nails per shingle in accordance with FBC 1507.2.7 or R905.2.6,with the following exceptions:
➢ Berkshire shingles require minimum five(5)nails per shingle.
➢ WeatherGuard'HP shingles require minimum six(6)nails per shingle.
Where the roof slope exceeds 21 units vertical in 12 units horizontal,special methods of fastening are required
Refer to Owens Corning published information on wind resistance and installation limitations.
6.3.1.1 Classic®&Supreme:
Normal Mansard or Area psra Normal Mansard or Area pare
Wind Areas High Wind desvanes y Wind Areas High Wind desvanes y
Area pare vientos normalas Areas vientos faerte3 Area pen vientos normeles Areas vienros fuertes
t' (A) 1., F.I. r (B 2• t' t"2 fA►
tt^ tr
• t t2t
. . . . . . . . . . . . . . . . .
S"Exposure 6 Wir Exposure
Exposicion Exposicidn
Figure 4:Minimum Nailing,Classic&Supreme Figure 5:Minimum Nailing,Classic&Supreme
j (Standard Size) (Metric Size)
NEMO ETC,LLC Evaluation Report 037940.02.12-119
Certifrcote of Authorization#32455 6-EDITION(2017)FBC NON-HVHZ EVALUATION F1.10674-1134
Owens Corning Asphalt Roof Shingles Revision 9:06/13/2019
Page 4 of 10
ONEMOletc.
6.3.1.2 Berkshire®:
Seabrt strip Sealantswp
Lathe da-se kdr.. La fua de sellador
1 8 Vz 9 yz" 9 W $Vt'. "8 pie" 8 7h" 8 rff 8 W,
Figure 6: S-Nail Pattern,Berkshire Figure 7: 6-Nail Pattern,Berkshire
Seab strIp
La tZra de wlkdor
:t3Yt 8�P $V
1
`X.
24 Asphalt roof
oig:cement
Ceiimnfodelecho.de dodd
Figure 8: Mansard or Steep Slope Pattern,Berkshire
I
NEW ETC,LLC Evaluation Report 037940.02.12-119
Certificate of Authorization#32455 6-EDITION(2017)FBC NON-HVHZ EVALUATION F1.10674-1114
Owens Corning Asphalt Roof Shingles Revision 9:06/13/2019
Page 5 of 10
ONEMOjetc.
6.3.1.3 Duration®,TruDefinition®Duration Duration®Premium Cool&TruDefinitiono Duration*Designer Color Collection:
4-Nail:FasteningPattern
SureN"fastenin8 area vu dtli
' Nail,_7ypical
- r�,cwierg surety •; .,�.�o �!�s� `r• orn.n candy sm.wa+� ,..o:.
r �
Figure 9:Standard 4-Nail Pattern,Duration
6-N911.Fastening_PattgM
SureNalN0fastening;area wlc th,
Nall;lyplcal,
1" 127• 42" 1"
-.Wr Scwi g 3—Mi J-,a a••-,,7: -L...:8uwn�
Figure 10: 6-Nail Pattern,Duration
Fastening fo-r:Slopes:GreaterThan,2112
SureNall®.faetening,area'iwldt6
Nall,Typical
1" 12" 12" 1"
r.'pxensCum!nps- 1.%_.;' ae.+5.815utoJ suae+0'c.- - �Oiaem CaNiq SiaeNaln "-ram.
exp"
'2R
6444
Four 1"Spots'ofAsphalt Rooflng:Cement
Figure 11: Mansard or Steep Slope Pattern,Duration
I
NEW ETC,LLC Evaluation Report 037940.02.12-119
Certificate ojAuthorization#32455 a EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R14
Owens Coming Asphalt Roof Shingles Revision 9:06/23/2019
Page 6 of 10
I '
ONEMOjetc.
6.3.1.4 TruDefinition"Oakridee®,Oakridee®:
-4 Na(i Pattern ,
'Esquema cor14 davos=
i
5$I8e Exposure,.. Nails
cfavos. 5 518 Exposure
£>rposfdonde5b/Spufg. Exposrc(dnde5&/Bprrlg
Figure 12:Standard 4-Nail Pattern,Oakridge
G-Naii`t'attem
wfta con 6 ctavos
. ' tz —
Nails:
53/8"Exposure Ctavos '5 518 Exposure -
Expos+cfort;de vr5/8pyfg: Fxposrcidride b5/8'pilg.
Figure 13:6-Nail Pattern,Oakridge
Fastening far Mopes Greater T,han;21:12.
SureNan fastening area width
Nall,Typical
Ir
..P"m CmdC5.�1-.. • ? .MCSdNo1..�0" ^..L cn fanb SSYta1 :�..
t -
e.t�"
Four v SpotS WAsphelt Roofing Cement
i
Figure 14:Mansard or Steep-Slope Pattern,Oakridge
NEMO ETC,LLC Evaluation Report 037940.02.12-R9
Certificate of Authorization#32455 0 EDITION(2017)FBC NON-HVHZ EVALUATION F1.10674-1114
Owens Corning Asphalt Roof Shingles Revision 9:06/13/2019
Page 7 of 20
ONEMOjetc.
6.3.1.5 WeatherGuard®HP:
'�
't�t2p 9�� I�
no am
E�dc6ti�de 5 68 ping. fitposiC�n do 6 pW�g.
Figure 1S:6-Nail Pattern,WeatherGuard HP
6 Nail Pattern
Esquema con 6 davos Nail 61/8'from,bottom
of,shilgle.
$518'Ex wre 8'Fasteners pave a 6118 pping de le
po 6 parte infeiorde la t4a
Exposici3n de 5 518 pulg. ,suJet rs.
2• t • —
Four 1'Spots of Asphalt Roof Cement
Cuatro puafos de cemado do tecbo de asfalto de 1 pulgada
Figure 16:Mansard or Steep-Slope Pattern,WeatherGuard HP
6.4 HIP'&RIDGE SHINGLES.
6.4.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions.
➢ Berkshire® Hip and Ridge Shingles with Sealant and DuraRidge® Hip& Ridge Shingles with Sealant require
minimum two(2)nails per shingle.
➢ WeatherGuard' HP Hip and Ridge Shingles and ProEdge® Hip & Ridge Shingles require minimum four(4)
nails per shingle.
Refer to Owens Corning published information on wind resistance and installation limitations.
NEMO ETC,LLC Evaluation Report 037940.02.12-119
CertifrcateofAuthorization#32455 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R14
Owens Corning Asphalt Roof Shingles Revision 9:06/13/2019
Page 8 of 10
ONEMOjetc.
6.4.1.1 Berkshire®Hip&Ridge with Sealant and DuraRidge®Hip&Ridge Shingles with Sealant:
Fig. A Fig. B
Prevailing Wind Direction Top View
Direccon del viento predominante Vista superior
Nail
25ln Clavo
A I e' .Owens:Comfng SiseNg",
Nails 4 �"
Clavos
1 I
I I I
I I I EI e
g EXIM,
Wn de e ping V
II I
A
12"
Figure 17:Isometric View,Berkshire and DuraRidge Figure 18:Plan View,Berkshire and DuraRidge
6.4.1.2 WeatherGuard®HP Hip&Ridge Shingles:
Fig;.A q Ftg C:Hip&-Ridge Shingle Fasterong.`
Preva�Ing 1NIad TopVkiY
Direction ."
Nails q`q
I I
A i i Nails Nails
I[ i1i
�osure .
5 Exposure.
Figure 19:Isometric View,WeatherGuard HP Hip&Ridge Figure 20:Plan View,WeatherGuard HP Hip&Ridge
NEMO ETC,LLC Evaluation Report 037940.02.12-R9
Certiflcateof Authorization#32455 6m EDITION(2017)FBC NON-HVHZ EVALUATION F1.10674-R14
Owens Corning Asphalt Roof Shingles Revision 9:06/13/2019
Page 9 of 30
i
I
ONEMOjetc.
6.4.1.3 ProEdge®Hip&Ridge Shingles:
Prevailing Standard11°
Wind Direction Fastening
SealarnStrip Pattern.
6•Exposure
j12Sealant
Fasten 711 78°Expos t eCover Exposed 1
Fasteners with
':Roof Cement
MIN
Figure 21:Isometric View,ProEdge Figure 22: Plan View,ProEdge
LABELING:7.
7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
7.2 Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FBC Table
1S07.2.7.1/R90S.2.6.1.
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation
of this product.
9. MANUFACTURING PLANTS:
Contact the named QA entity for information on which plants produce products covered by Florida Rule 61G20-3
QA requirements.
QUALITY10.
PRI Construction Materials Technologies,LLC—QUA9110; 813 621-5777;bwilson@pricmt.com
END OF EVALUATION REPORT-
NEMO ETC,LLC Evaluation Report 037940.02.12-R9
Certificate of Authorization#32455 6TM EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-1114
Owens Corning Asphalt Roof Shingles Revision 9:06/23/2019
Page 10 of 10