HomeMy WebLinkAboutproduct approvalMIAMI•DADE
MIAMI-DADE COUNTY
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA)
www.miamidade.gov/economy
Atlas Roofing Corporation
2000 Riveredge Parkway
Suite 890
Atlanta, GA. 30328
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Gorilla Guard Spec 30 and Gorilla Guard 30
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA# 13-0425.13 and consists of pages I through 3.
The submitted documentation was reviewed by Alex Tigera.
MIAMI-DADECouN7Y r ((-v NOA: 18-0501.06
• Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 1 of 3
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Underlayment
Material: Asphalt
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
Product
Gorilla Guard Spec 30
Manuf. Location 0 1 & 2
Gorilla Guard 30
Manuf. Location # 2
Test
Dimensions Specification
Product
Description
36" x 72' rolls ASTM D 226 Type II Fiberglass reinforced inorganic felt
underlayment
36" x 144.5' ASTM D 226 Type II Fiberglass reinforced inorganic felt
rolls underlayment
MANUFACTURING LOCATION:
1. Meridian, MS
2. Tuscaloosa, AL.
EVIDENCE SUBMITTED:
Test Agency Test Identifier
PRI Construction Materials Technologies ATL-101-02-01
ATL-234-02-01
ATL-235-02-01
INSTALLATION
Test Name/Report
Date
ASTM D 226 Type II
02/18/13
ASTM D 226 Type II
05/24/18
ASTM D 226 Type II
05/24/18
1. Atlas Roofing Corporation's Gorilla Guard Spec 30 and Gorilla Guard 30 and its components shall be installed
in strict compliance with applicable Building Codes.
2. Gorilla Guard Spec 30 and Gorilla Guard 30 shall be installed with 4-inch head laps in a single layer fashion
and a 6-inch end lap.
3. Gorilla Guard Spec 30 and Gorilla Guard 30 shall be fastened with corrosion resistant tin -caps and 12 guage 1-
1/4" annular ring -shank nails, spaced 6" o.c. at the laps and two (2) staggered rows in the field spaced 12" o.c.
4. Gorilla Guard Spec 30 and Gorilla Guard 30 may be used with asphaltic shingles, wood shakes and shingles,
non-structural metal roofing, quarry slate, and tile roofing when used as a mechanically attached base sheet.
BUILDING PERMIT REQUIREMENTS:
Application for building permit shall be accompanied by copies of the following:
1. This Notice of Acceptance.
2. Any other documents required by the Building Official or applicable building code in order to properly
evaluate the installation of this material.
NOA: 18-0501.06
Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 2 of 3
LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product.
2. Gorilla Guard Spec 30 and Gorilla Guard 30 shall not be left exposed for more than 30 days.
3. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code.
4. All packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo and a yellow
line in the center of the roll to identify the ASTM Standard designation or the Miami -Dade County Product
Control Seal as shown below.
END OF THIS ACCEPTANCE
NOA: 18-0501.06
Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 3 of 3
M® MUMADE
MIAMI-DADE COUNTY
r
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
11805 SW 26 Slreet, Room 208
BOARD AND CODE ADMINISTRATION DIVISION
Miami, Florida 33175-2474
T (786) 315-2590 F (786)315-2599
NOTICE OF ACCEPTANCE (NOA)
www.miamidade.eov/economy
CertainTeed Corporation
20 Moores Road
Malvern, PA 19355
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within theirjurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Landmark, Landmark Pro, Landmark Premium, Landmark Impact Resistant, Landmark
Solaris Gold/Platinum and Landmark Pro/Architectural 80
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been tiled and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA # 15-0714.19 and consists of pages 1 through 6.
The submitted documentation was reviewed by Alex Tigera.
MIAMI DADE COUM
, r
NOA No.: 16-1109.18
Expiration Date: 02/28/22
Approval Date: 02/09/17
Page 1 of
MIAMI•DADE
MIAMI-DADE COUNTY
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA)
www.miamidade.gov/economy
Atlas Roofing Corporation
2000 Riveredge Parkway
Suite 890
Atlanta, GA. 30328
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Gorilla Guard Spec 30 and Gorilla Guard 30
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA# 13-0425.13 and consists of pages I through 3.
The submitted documentation was reviewed by Alex Tigera.
MIAMI-DADECouN7Y r ((-v NOA: 18-0501.06
• Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 1 of 3
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Underlayment
Material: Asphalt
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
Product
Gorilla Guard Spec 30
Manuf. Location 0 1 & 2
Gorilla Guard 30
Manuf. Location # 2
Test
Dimensions Specification
Product
Description
36" x 72' rolls ASTM D 226 Type II Fiberglass reinforced inorganic felt
underlayment
36" x 144.5' ASTM D 226 Type II Fiberglass reinforced inorganic felt
rolls underlayment
MANUFACTURING LOCATION:
1. Meridian, MS
2. Tuscaloosa, AL.
EVIDENCE SUBMITTED:
Test Agency Test Identifier
PRI Construction Materials Technologies ATL-101-02-01
ATL-234-02-01
ATL-235-02-01
INSTALLATION
Test Name/Report
Date
ASTM D 226 Type II
02/18/13
ASTM D 226 Type II
05/24/18
ASTM D 226 Type II
05/24/18
1. Atlas Roofing Corporation's Gorilla Guard Spec 30 and Gorilla Guard 30 and its components shall be installed
in strict compliance with applicable Building Codes.
2. Gorilla Guard Spec 30 and Gorilla Guard 30 shall be installed with 4-inch head laps in a single layer fashion
and a 6-inch end lap.
3. Gorilla Guard Spec 30 and Gorilla Guard 30 shall be fastened with corrosion resistant tin -caps and 12 guage 1-
1/4" annular ring -shank nails, spaced 6" o.c. at the laps and two (2) staggered rows in the field spaced 12" o.c.
4. Gorilla Guard Spec 30 and Gorilla Guard 30 may be used with asphaltic shingles, wood shakes and shingles,
non-structural metal roofing, quarry slate, and tile roofing when used as a mechanically attached base sheet.
BUILDING PERMIT REQUIREMENTS:
Application for building permit shall be accompanied by copies of the following:
1. This Notice of Acceptance.
2. Any other documents required by the Building Official or applicable building code in order to properly
evaluate the installation of this material.
NOA: 18-0501.06
Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 2 of 3
MIAMI•DADE
MIAMI-DADE COUNTY
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA)
www.miamidade.gov/economy
Atlas Roofing Corporation
2000 Riveredge Parkway
Suite 890
Atlanta, GA. 30328
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Gorilla Guard Spec 30 and Gorilla Guard 30
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA# 13-0425.13 and consists of pages I through 3.
The submitted documentation was reviewed by Alex Tigera.
MIAMI-DADECouN7Y r ((-v NOA: 18-0501.06
• Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 1 of 3
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Underlayment
Material: Asphalt
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
Product
Gorilla Guard Spec 30
Manuf. Location 0 1 & 2
Gorilla Guard 30
Manuf. Location # 2
Test
Dimensions Specification
Product
Description
36" x 72' rolls ASTM D 226 Type II Fiberglass reinforced inorganic felt
underlayment
36" x 144.5' ASTM D 226 Type II Fiberglass reinforced inorganic felt
rolls underlayment
MANUFACTURING LOCATION:
1. Meridian, MS
2. Tuscaloosa, AL.
EVIDENCE SUBMITTED:
Test Agency Test Identifier
PRI Construction Materials Technologies ATL-101-02-01
ATL-234-02-01
ATL-235-02-01
INSTALLATION
Test Name/Report
Date
ASTM D 226 Type II
02/18/13
ASTM D 226 Type II
05/24/18
ASTM D 226 Type II
05/24/18
1. Atlas Roofing Corporation's Gorilla Guard Spec 30 and Gorilla Guard 30 and its components shall be installed
in strict compliance with applicable Building Codes.
2. Gorilla Guard Spec 30 and Gorilla Guard 30 shall be installed with 4-inch head laps in a single layer fashion
and a 6-inch end lap.
3. Gorilla Guard Spec 30 and Gorilla Guard 30 shall be fastened with corrosion resistant tin -caps and 12 guage 1-
1/4" annular ring -shank nails, spaced 6" o.c. at the laps and two (2) staggered rows in the field spaced 12" o.c.
4. Gorilla Guard Spec 30 and Gorilla Guard 30 may be used with asphaltic shingles, wood shakes and shingles,
non-structural metal roofing, quarry slate, and tile roofing when used as a mechanically attached base sheet.
BUILDING PERMIT REQUIREMENTS:
Application for building permit shall be accompanied by copies of the following:
1. This Notice of Acceptance.
2. Any other documents required by the Building Official or applicable building code in order to properly
evaluate the installation of this material.
NOA: 18-0501.06
Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 2 of 3
LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product.
2. Gorilla Guard Spec 30 and Gorilla Guard 30 shall not be left exposed for more than 30 days.
3. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code.
4. All packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo and a yellow
line in the center of the roll to identify the ASTM Standard designation or the Miami -Dade County Product
Control Seal as shown below.
END OF THIS ACCEPTANCE
NOA: 18-0501.06
Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 3 of 3
M® MUMADE
MIAMI-DADE COUNTY
r
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
11805 SW 26 Slreet, Room 208
BOARD AND CODE ADMINISTRATION DIVISION
Miami, Florida 33175-2474
T (786) 315-2590 F (786)315-2599
NOTICE OF ACCEPTANCE (NOA)
www.miamidade.eov/economy
CertainTeed Corporation
20 Moores Road
Malvern, PA 19355
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within theirjurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Landmark, Landmark Pro, Landmark Premium, Landmark Impact Resistant, Landmark
Solaris Gold/Platinum and Landmark Pro/Architectural 80
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been tiled and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA # 15-0714.19 and consists of pages 1 through 6.
The submitted documentation was reviewed by Alex Tigera.
MIAMI DADE COUM
, r
NOA No.: 16-1109.18
Expiration Date: 02/28/22
Approval Date: 02/09/17
Page 1 of
ROOFING ASSEMBLY APPROVAL
Cateeorv:
Roofing
Sub-Cateeorv:
Asphalt Shingles
Materials
Dimensional
Deck Type:
Wood
SCOPE
This acceptance is for CertainTeed Landmark, Landmark Pro, Landmark Premium, Landmark Impact
Resistant and Landmark Solaris Gold/Platinum Shingles as manufactured by CertainTeed Corporation described
in Section 2 of this Notice of Acceptance.
PRODUCT DESCRIPTION
Product Dimensions Test Product Descrintion
Specifications
Certainteed Landmark
,Manufacturing Locations #1, 2, 3, 4, 5, 6, 7, 8, 9,
10
Certainteed Landmark Pro
Manufacturing Locations # I, 3. 4. 5, 6, 9
Certainteed Landmark Premium
Manufacturing Locations # I, 3, 4, 5, 6, 8, 9
Certainteed Landmark Impact Resistant
Manufacturing Locations # 1, 7
Certainteed Landmark Pro/Architect 80
Manufacturing Locations #8
Certainteed Landmark Solaris Gold/Platinum
Manufacturing Locations # 1, 8
Accessory Shingles
A heavy weight, dimensional
13'/V x 38 %" TAS 110 asphalt shingle.
13'/<" x 38 %" TAS 110
13'/a" x 38'/a" TAS 110
13'/V x 38'/a" TAS 110
13''A" x 38'/a" TAS 110
13'A" x 38'/4" TAS 110
A heavy weight, dimensional
asphalt shingle.
A heavy weight, dimensional
asphalt shingle.
A heavy weight, dimensional
asphalt shingle.
A heavyweight, dimensional
asphalt shingle.
A heavyweight, dimensional
asphalt shingle.
various proprietary Accessory shingles for hip, ridge
and starter strip applications.
NOA No.: 16-1109.18
Expiration Date: 02/28/22
Approval Date: 02/09/17
Page 2 of 6
LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for
fire ratings of this product.
2. Gorilla Guard Spec 30 and Gorilla Guard 30 shall not be left exposed for more than 30 days.
3. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code.
4. All packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo and a yellow
line in the center of the roll to identify the ASTM Standard designation or the Miami -Dade County Product
Control Seal as shown below.
END OF THIS ACCEPTANCE
NOA: 18-0501.06
Expiration Date: 06/13/23
Approval Date: 06/21/18
Page 3 of 3