HomeMy WebLinkAboutProduct Approval (3) MIAMI- MIAMI-DADE COUNTY
4`21LEPPRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOUR 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami,Florida 33175-2474
T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE OA www.miamidade.Eov/huildin1
Sun-Tek Manufacturing,Inc. "05
10303 General Dr.
Orlando,FL 32824 SCOPE: mittingThis NOA is being issued under the applicable rulern a use of construction materials.
The documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control
Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction
(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control
Section(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County)reserve the right to
have this product or material tested for quality assurance purposes.If this product or material fails to perform in
the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately
revoke,modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right
to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or
material fails to meet the requirements of the applicable building code.
This product is approved as described herein,and has been designed to comply with the High Velocity Hurricane
Zone of the Florida Building Code.
DESCRIPTION: MD-CMA.Skylight.
APPROVAL DOCUMENT: Drawing No. CMA-002,titled "MD-CMA",sheets 1 and 2 of 2,prepared by
Sun-Tek Manufacturing,Inc., dated May 09,2011,signed and sealed by James D.Wells,Jr.,P.E.,on October
06,2017,bearing the Miami-Dade County Product Control Revision stamp with the Notice of Acceptance
number and the expiration date by the Miami-Dade County Product Control Section.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
LABELING:Each unit shall bear a permanent label with the manufacturer's name or logo,city,state and
following statement: "Miami-Dade County Product Control Approved"or the Product Control Seal,unless
otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no
change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in
the materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any
product,for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply
with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County,Florida, and followed by
the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it
shall be done in its entirety.
INSPECTION:A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors
and shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA#15-0513.05 and consists of this page 1, evidence submitted pages E-1,E-2, and E-3 as
well as approval document mentioned above.
The submitted documentation was reviewed by He my A.Makar,P.E.,M.S.
1NOA No. 17-1023.18
MIAMI•DADE COUNTYM
� Expiration Date: 03/13/2023
Approval Date: 03/15/2018
/ / Page 1
Sun-Tek Manufacturing,Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL#08-0110.06
A. DRAWINGS
1. Manufacturer's die drawings and sections.
Z. Drawing No. CMA-002, titled "IM-CMA", sheets 1 and 2 of 2,prepared by Sun-Tek
Manufacturing, Inc., dated 09113195 and 04125195, with no revisions, signed and sealed by
Rene J. Quiroga, P.E.
B. TESTS
1. Test reports on 1)Air Infiltration Test,per FBC, TAS 202-94
2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
3) Water Resistance Test,per FBC, TAS 202-94
4)Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
6)Forced Entry Test,per FBC 24113.2.1, TAS 202-94
along with marked-up drawings and installation diagram of Model MD-CMA Curb
Mounted Plastic Dome Skylight,prepared by National Certified Testing Laboratories,
Test Report#210-2885-1, dated 10131102, signed and sealed by W. A. Davis Jr., P.E.
C. CALCULATIONS
1. Anchor calculations prepared by Product Technology Corporation on 02105103,
signed and sealed by A. Perez Maldonado, PE.
D. QUALITY ASSURANCE
1. Miami Dade Building Code Compliance Office(BCCO)
E. MATERIAL CERTIFICATIONS
1. Notice of Acceptance No. 07-0212.01 issued to General Electric Plastics for their
"Leaan Sheet Products", approved 05/25/07, expiring on 07/17/08.
F. STATEMENT
1. Code compliance letter issued by Product Technology Corporation on 02/06/03,
signed and sealed by A. Perez Maldonado
(Evidence Submitted under NOA # 03-0401.07)
G. OTHERS
1. Notice of Acceptance No. 03-0401.07, issued to Sun-Tek Manufacturing,Inc.,
approved on 10/09/03 and expiring on 03/13/08.
2. No change letter issued by Sun-Tek Manufacturing, Inc., dated 01/02/08,signed by
James Feudner.
elmy A.Makar,P.E.,M.S.
Product Control Section Supervisor
NOA No. 17-1023.18
Expiration Date: 03/13/2023
Approval Date: 03/15/2018
E-1
Sun-Tek Manufacturing,Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
2. EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL#11-0601.04
A. DRAWINGS
1. Drawing No. CMA-002, titled ".&M-CMA", sheets I and 2 of 2,prepared by Sun-Tek
Manufacturing, Inc., dated May 09, 2011, signed and sealed by James D. Wells, Jr.,
P.E., on May 08, 2012.
B. TESTS
L Test reports on 1)Air Infiltration Test,per FBC, TAS 202-94
2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-94
3) Water Resistance Test,per FBC, TAS 202-94
4)Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
6)Forced Entry Test,per FBC 24113.2.1, TAS 202-94
along with marked-up drawings and installation diagram of Model MD-CMA Curb
Mounted Plastic Dome Skylight,prepared by National Certified Testing Laboratories,
Test Report No. NCTL-210-3859-1, dated 03104113, signed and sealed by Gerard J.
Ferrara, P.E.
C. CALCULATIONS
1. Anchor calculations prepared by J&L Wells Consulting LLC, 19 pages, dated
0311912013, signed and sealed by James D. Wells, Jr., P.E.
D. QUALITY ASSURANCE
1. By Miami-Dade County Department of Regulatory and Economic Resources.
E. MATERIAL CERTIFICATIONS
1. None.
F. STATEMENT
1. Florida Building Code, 2010 Edition, compliance letter prepared by J&L Wells
Consulting LLC, dated 0412512012, signed and sealed by James D. Wells, Jr., P.E.
3. EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL#15-0513.05
A. DRAWINGS
1. Drawing#CM4-002, titled "MD-CMA", sheets 1 and 2 of 2,prepared by Sun-Tek
Manufacturing,Inc., dated 05109111, signed&sealed by James D. Wells,Jr., P.E., on
05108112.
B. TESTS
1. None.
C. CALCULATIONS
1. None.
y A.Makar,P.E.,M.S.
Product Control Section Supervisor
NOA No. 17-1023.18
Expiration Date: 03/13/2023
Approval Date: 03/15/2018
E-2
Sun-Tek Manufacturing,Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
D. QUALITY ASSURANCE
1. By Miami-Dade County Department of Regulatory and Economic Resources.
E. MATERIAL CERTIFICATIONS
1. None.
F. STATEMENT
1. Florida Building Code, 2014 Edition, compliance letter prepared by J&L Wells
Consulting LLC, dated 0510512015, signed and sealed by James D. Wells, Jr., P.E.
4. NEW EVIDENCE SUBMITTED
A. DRAWINGS
1. Drawing No. CMA-002, titled "MD-CMA", sheets 1 and 2 of 2,prepared by Sun-Tek
Manufacturing, Inc., dated May 09, 2011, signed and sealed by James D. Wells, Jr.,
P.E., on October 06, 2017.
B. TESTS
1. None.
C. CALCULATIONS
1. None.
D. QUALITY ASSURANCE
1. By Miami-Dade County Department of Regulatory and Economic Resources.
E. MATERIAL CERTIFICATIONS
1. None.
F. STATEMENT
1. Florida Building Code, 2017 Edition, compliance letter prepared by J&L Wells
Consulting LLC, dated 1010612017, signed and sealed by James D. Wells, Jr., P.E.
elmy A.Makar,P.E.,M.S.
Product Control Section Supervisor
NOA No. 17-1023.18
Expiration Date: 03/13/2023
Approval Date: 03/15/2018
E-3
�li,�t,attttrrj,
e� W jo
J&L Wells Consulting LLC
Engineer of Record: 1453 Arbitus Circle
g dV�t. 53616
James D.Wells,Jr.,P.E. Oviedo,FI.32765 arm
Professional Engineer No.53616 (407)496-5484 = i _��
Certificate of Authorization No.27162 STATE OF ,r� �,
pp;
PARTA 0—C 2
A PLA YM I DRAWN t3Y: L 8. RE DWG. CMA—pO2
{ —w--3.000OS14.625---! rl11II1
VILER CONE.070 Poo dPH?U2
.070 POCYCAROOW$SHLtR
PALRAN PAlS5UOrI
SNEONE CEDDNO(00NIORM) SXEriX WxR0.0N m
Si5-lOSOOL" i SEN SWC U.M 9D3.
M (COHrOLSDI)
p pco o(CD I„c sn_ZZre
0 QQ o60 rwCR N.LN4HUH
O (,7 NAISNEwt0E0RfDaNEaS o nvs huam PW
,� � ,187((5tt�1• )5 NuMn,vn RUeI 4JyLp-}Pu ,p}0 PagewoMm
{1J�4Z smE PAUAY
SM
HIrXAN�±ON.or
(10%2 PHULIP3 PAN MEAD 5!&ET UEUE SLREW
(A)ON LONE 9ori(3)ON$Hoar SIRE _
DIMENSIONS FOR
X `1A1
v
FASTENER LOCATIONS lY 01 WS�LL1.htr Ml
d ro:3'Ncs))ON LCMD S+DEsix , 14`• OMIMCRS COUNr(YJ� rD p rt')
14 FASTENERS ,Q r�H4"011K j CR—'—��. G]
T❑ CURB MD—CMA 2246 n! ACCOR"Icl; rH%MA sLmws(2)
2r STP(SC 455)CURB HECHL 70 DE
VwSV7nGENr r0 4NN7NN
Gr rwNtt fp r suaVM[
RIVETS SWPUED Br O)MPS IN
MOTE:
POLY TO ALUM (A7PROKO R7 DA%j COON 71
RIVET LOCATIONS SYM o (1) ALL ROOFING DETAILS SHALL COMPLY WITH
C) CHAPTER 15 OF THE 2017 FLORIDA 13UILDING CODE
oDESIGN PRESSURE RATING
(2) 4"MINIMUM DISTANCE FROM ANGLE LIP TD ROOF +— 6O PSE.
SURFACE IS FOR SHINGLE. OR B.U.R. WITHOUT
INSULATION, FOR INSULATION AND TILE ROOF ADD LARGE MISSILE IMPACT RESISTANCE
TILE HEIGHT AND INSULATION THICKNESS TO 4"
MINIMUM HEIGHT.
(3) ANCHORS TO BE MADE OF NON—CORROSIVE MATERIAL.
-- COMPATABLE WITH ALUMINUM.
13.625--►
27.256 MAX.
aa.RO.&3L'(-' 'REVISED
FASTENER SCHEDULE SKYLIGHT TO CURB FASTENER SCHEDULE CURB RIVET SCHEDULE OECD RS CO`s Y G
010 X 2 PAN HEAD SHEET METAL SCRE S TO DECK OID X 3- DECK TO POLYCARBONATE 3/16" OLA, p in with tlr0 FlmYiGl
SCREWS i3311;j>:KS @�".G,�qy
PER LONG PER SHORT PER LONG PER SHORT PER LONG PER-S;ORT -r-LCOD+'rt
MODEL SIDE SIDE SIDE SIDE SIDE SIDE can(a No
Exp#tr I "a Date O G?
246 4 3 4 3 2 1 pyj
2 306 4 3 a 3 2 1 �V
3 _
3
1919 3 3 3 3 i t ltila`!` t I} UC'
1446 4 a 3 1
i
1422 3 3 3 1 1
4 4 2 2
RLv7StON EVIStONI PRObUCT NAME+
ID—CMA SUN-TEK MANUFACTURINEFL
L32�8244
T :5 31 ALEr G N(C A- 10303 GENERAL DRIVE ORLANDO.
J&L Wells Consulting LLC �v.%'0
1453 Arbitus Circle
Engineer of Record:
Oviedo,FL 32765 0. 3616
01�4i
James D.Wells,Jr.,P.E, (407)496-5489
Owl
Professional Engineer No.53616 Certificate of Authorization No.27162
01'k
4%_& STAIM OF -Z-
PART NAME: PRO C7 I SHE Z
0 2
DRAWN BY. J6
,-,
DESIGN PRESSURE RATING //J111111110""
+- 60 PSF
910 X 2" SCREW PPH LARGE MISSLE IMPACT RESISTANCE OUTER DOME .070 POLYCARBONATE
(4) ON LONG SIDE& (3) ON SHORT SIDE (Pairom Polsun,
MINIMUM ENBEDMENT 1'* Sheffield Mokrolon or
Subic Lexan 9034) SILICONE BEDDING (CONTINUOUS)
DECO RING STI-275 BUTYL RUBBER SEALANT
.060 THICK ALUMINUM
6063 76 MITRE BETWEEN SKYLIGHT
AND WELDED CORNERS AND CURB (continuous)
INNER LINER .030 polycorbonote 5-1/2" DOME RISE SHIM( EA ANCHOR (TYP)
(Polrom Polsun, AIR FILIED INSULATED SPACE WITH LOAD BEARING SHIM
Sheffield Mokrolon or 0.500 MAX.
Sobic Lexon 9034)
xxy_y"ywyv� xxxxxx%x:l
as cornlllying witi'tl"q.-Vid.
Building Code 3/16" RIVET
AccepCinco No I I-10 4? /LONG SIDE
EViz ti Datet> m/SHORT SIDE
BY
'5U Mimni ad C 0 r0. ff 10 x 3" DECK SCREW
FINISHED WALL MATERIAL (4) ON LONG SIDE FLASHING BY OTHERS IN
"' U U
Dad
4" MINIMUM (3) ON SHORT SIDE
r' BY OTHERS ( APPROVED [ACCORDANCE WITH NRCA
SEE NOTE #2
DADE COUNTY) MINIMUM ENBEDME
S-ONCLES (2)
a Ln
NOTE: 000
. �
(1) ALL ROOFING DETAILS SHALL COMPLY WITH M
CHAPTER 15 OF THE 2017 FLORIDA BUILDING CODE
(2) 4" MINIMUM DISTANCE FROM ANGLE LIP TO ROOF
SURFACE IS FOR SHINGLE. OR B.U.R. WITHOUT
2X SYP (SG 0.55) CURB HEIGHT INSULATION. FOR INSULATION AND TILE ROOF ADD
TO BE SUFFICIENT TO MAINTAIN TILE HEIGHT AND INSULATION THICKNESS TO 4"
4" MINIMUM AT LOWEST POINT MINIMUM HEIGHT.
OF FRAME TO ROOF SURFACE (3) ANCHORS TO BE MADE OF NON-CORROSIVE MATERIAL, ROOF DECK
SUPPLIED BY OTHERS AN COMPATABLE WITH ALUMINUM,
(APPROVED BY DADE COUNTY) STS7"'-100_'
0 SEALANT (CONTINOUS)
REVISION: REVISION.. PeoDucf NAa1E+
ID-CMA SUN-TEK MANUFACTURING, INC,
IINI, ATEIDAT -SCALr: I DWG No.(MA-002 10503 GENERAL DRIVE ORLANDO, FL 32824