Loading...
HomeMy WebLinkAboutProduct Approval E D0'9 Permitting EXTERIOR RESEARCH &DESIGN, LLC. Certificate of Authorization#9503 \ ERD 353 CHRISTIAN STREET, UNIT#13 TRINITY. OXFORD, CT 06478 (203) 262-9245 EVALUATION REPORT Owens Corning Evaluation Report 037940.02.12-RS One Owens Corning Parkway FL10674-R13 Toledo,OH 43659 Date of Issuance:02/06/2012 (740)404-7829 Revision 8: 10/09/2017 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 6th Edition (2017) Florida Building Code sections noted herein. DESCRIPTION: Owens Corning Asphalt Roof Shingles LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein and FBC 1507.2.7.1/R905.2.6.1. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity IERD Evaluated" may be displayed in >_1 advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety. INSPERION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. 0 This Evaluation Report consists of pages 1 through 8. Prepared by: ,S rLn;rr. UJ Robert J.M. Nieminen,P.E. The facsimile seal appearing was authorized by Robert Y �] Florida Registration No.591E6,Florida DCA ANE1983 Nieminen,F.E on 10!09/2017. This does not serve as an electronically signed document. U. CERTIFICATION OF INDEPENDENCE: 1. Trinity IERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Trinity ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen,P.E.does not have,nor will acquire, a financial interest in any other entity involved in the approval process of the product. S. This is a building code evaluation. Neither Trinityl ERD nor Robert Nieminen, P.E. are, in any way,the Designer of Record for any project on which this Evaluation Report,or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. � + , . \ / �K��m ���� ~`J K U��U»�K K D +��^�~ ROOFING SYSTEMS EvxWAnOm: 1' Scopo Product Category: Roofing Sub-Category: Asphalt Shingles Compliance Statement: Owens Corning Asphalt Roof Shingles, as produced by Owens Corning,have demonstrated compliance with the following sections ofthe 6"' Edition (20I7) Florida Building Code and Florida Building Code, Residential Volume through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations/Conditions of Use set forth herein. I. STmmoAnos: Section Property Standard� Year 1S07.2.5,R905.2.4 Physical Properties ASTM D3462 2010 1507.2,7.1,R905.2.6.1 Wind Resistance ASTM Daz61 2016 1507.2.7.1,R905.2.6.1 Wind Resistance ASTM o7zSQ zozz 3. RcpsnsmcEu Entity ExaminationReference Date . uLLLC([Ene6aG) Physicals&vwndResistance File R24s]'Vol,a 02/15/2007 uLLLC(c[K96Za) Physicals&Wind Resistance 20120516'112453 05/16/2012 uLLLC(TSTgaZu) Physical Properties 06[A2026] 04Y18/2006 uL LLI(TsTysZo) Wind Resistance 11[x34308 02/18/2013 uLLLC(TSrsG2a) Physicals&Wind Resistance 4786083137 02/01/2014 uL LLI(TITe62u) vvmd Resistance 4786126532 02/10/2014 UL LLI(TsTyolu) Physical Properties Classification letter 02/13/2014 uLLLC(TST96Zo) Physical Properties Classification letter 10/02/2015 xxi^mi'oade([EnzseZ) Fo[HvHzCompliance variousmCA, Various uLLL{ (QV^9625) Quality Control Service Confirmation Exp.05/16/2020 4' PRODUCT DESCRIPTION: 4.1 Asphalt Shingles: 4.1.1 Classic' and Supreme' are fiberglass reinforced,3-tabasphalt roof shingles. 4.1.2 Berkshire' are fiberglass reinforced,4'tabasphalt roof shingles. 4.1.3 Devonshire= are fiberglass reinforced,5-tabasphalt roof shingles. 4.1.4 Duration', TruDefinidnn' Duration~' Duration' Premium Cool, TruDefin\tion' Duration' Designer Color Collection, TruDefinidnn^Oak,idge^, Oakridge' and VVeatherGuand` HP are fiberglass reinforced, laminated asphalt roof shingles. 4.2 Hip&Ridge Shingles: 4.2.I Berkshire~ Hip D. Ridge Shingles, High Phdge,VVeatherGuard' HP Hip & 0dgeSh\n�e� ProEdgeHip & Ridge Shingles and DuraRidge'" Hip&Ridge Shingles are fiberglass reinforced,hip and ridge asphalt roof shingles. 4.3 Accessor Starter Strips: 4.3.1 Starter Strip Shingle,Starter Strip Plus and Starter Shingle Roll are starter strips for asphalt roof shingles. 5. LIMITATIONS: 51 This is a building code evaluation. NeitherThnitylERD nor Robert Nisminsn' P.E. are. in anyway the Designer of Record for any project on which this Evaluation Report,or previous versions thereof,\s/wasused for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report isnot for use inFBCHVHZjurisdictions. 5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire ratings ofthis product. Exterior Research and Design,LLC. Evaluation Report o3re4o.oz.zz'xo Certificate af»wa",u"m,"#9503 GT'EDITION(mz7)pacmom'ov*zEVALUATION pu06/4-n13 Owens Coming Asphalt Roof Shingles Revision m:zo/oy/nmz/ Page oofa TRfNITY ERD 5.4 Wind Classification: 5.4.1 All Owens Corning asphalt shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161,Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for use in all wind zones up to Vasd = 150 mph (V,it = 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.2 All Owens Corning hip & ridge shingles, Starter Strip Shingle and Starter Strip Plus noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the shingles are acceptable for use in all wind zones up to Vasd= 150 mph (V,It= 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.3 Classification by ASTM D7158 applies to exposure category B or C, as defined in FBC 1609.4.3, and a mean roof height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. 5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations. 5.5 All products in the roof assembly shall have quality assurance audit in accordance with F.A.C.Rule 61G20-3. 6. INSTALLATION: 6.1 Underlavment: 6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product Approval,or be Locally Approved per Rule 61G20-3, per FBC 1507.2.3,1507.2.4 or R905.2.3. 6_2 Asphalt Shingles: 6.2.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following exceptions: Berkshires shingles require minimum five(5) nails per shingle. WeatherGuarda HP shingles require minimum six(6)nails per shingle. Devonshire'"shingles require minimum six(6)nails per shingle. Starter Strip Shingle and Starter Strip Plus require minimum five(5) nails per strip. Refer to Owens Corning published information on wind resistance and installation limitations. 6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required. See figures below for details. 6.2.5 Minimum Nailing—Starter Strip Shingle and Starter Strip Plus: Felt underlayment Deck Fek tndedeyment %„ fleck W4dhered Self-adhered laymcrtl -adhered _ WeatherLock8 WeatherLock4 ci underlayment I it Drip_ Drip edge trip-- Dip edge Drip— edge ,. edge Nails located Na&located 2'from eave 3'hom save Install first Self-searing adhesive S.jf c aFng adhesiva Starter SriP positioned along eave Instal rust sane•Strip MIS positioned along ea" shingle with _ with 6'mmoved 6"removed \ Starter Strip shingle overhangs eaves and rakes,y"-s.' Startw Stip Pks overhangs raves and ekes 114--3/4' Exterior Research and Design,LLC. Evaluation Report 037940.02.12-118 Certificate of Authorization#9503 6r"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-R13 Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 3 of 8 i y TRINITY'ERD 6.2.6 Minimum Nailing—Classic®&Supreme: Normal Mansard or Area para Normal Mansard or Arca para WlYnd Arses High Wind d■svones y Wind Aram High Wind desvanes y Area pars vientos normales Areas vientos fuertes Arca pan vientos normales Areas vientos fuertes �'" (B rr r �u IBl rz. i. 5'Expown 5 5/8'Exposure Erposici6n Exposici6n 6.2.7 Minimum Nailing—BerkshireO: &tahrt snip Sealant strip Le!sr de sa.adu /la fea de sellador 8 Y:' 9 Y: 9 Yf S Y f Ott" 8 W 8 ve . r Standard Fastening Pattern 6-Nail Fastening Pattern Sealant strq, La Lira da sa.txbr 1' t - - 1 - 2' Asphak roofing oanenl Camartlo de!Echo de asI9a Mansard or Steep Slope Fastening Pattern Exterior Research and Design,LLC. Evaluation Report 037940.02.12-R8 Certificate o(Authorizotion#9503 6"EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-1113 Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 4 of 8 ~ � � ( \ / ���x����� ��� ' K ��Kn `�U U V '^-^^�� 6l8 Minimum Nailing—Devonshre=: FF-- I I Nails Ten V Spot of Asphalt goof Cement Standard 6-maUFastening Pattern Mansard or Steep Slope Fastening Pattern 6.2.9 Minimum Nailing — Duration', Truoefnitions Duration, Duration" Premium Cool Q TmDefnition^ Duration Designer Color Collection: 4-Nall Fastening Pattern "all Fastening Fattem ir Ir _7L!411 Standard Fastening Pattern s-mai|Fastening Pattern -L!;-f Mansard o,Steep Slope Fastening Pattern Exterior Research and Design,LLC. Evaluation Report ozm4uoz.zz-Ro Certificate"fx"th"rizau""m,03 s`"EDITION(zoo)rocmom'xvxzEVALUATION pu0674-1113 owensco,n/"o*anno/txuo,so/nn/es Revision u.zn/oo/zo1r Page s"fo -.-,--JTRINITY'ERD 6.2.1 Minimum Nailing—TruDefinition'Oalkridgee,Oakridge®: 4 Nail P&om 6 Nail Pattern E;quama con 4 earns Esqjema con 6 c1ms T-4 F F7 5 BIr Exposure5 B.S-Eqm Hals Nails EXP017cun de 5 S/C pLdq� 6 5..S'Exposm IQ 5 5;8'Exposure Clavas clavos Eqpasici6a de 6 5!'GPzdg. Expas;cidn de 6 5,1S pdg. Standard Fastening Pattern 6-Nail Fastening Pattern Fastening for Slopes Greater Than 21:12 - kkh q Wy W ir Ir Mansard or Steep Slope Fastening Pattern 6.2.1 Minimum Nailing—WeatherGuarP.HP: Ungle 61clie%qW 2 Exterior Research and Design,I.I.C. Evaluation Report 037940.02.12-R8 Certificate of Authorization 9503 6"EDITION(2017)FBC NON-HVHZ EVALUATION I'l-10674-1113 Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 6 of 8 .y TRINITY ERD 6.3 Hip&Ridge Shingles: 6.3.1 Installation of Berkshire' Hip and Ridge Shingles, High Ridge, WeatherGuardt HP Hip and Ridge Shingles and ProEdge Hip & Ridge Shingles shall comply with the Owens Corning current published instructions, using four (4) nails per shingle. Installation of DuraRidgeTM" Hip & Ridge Shingles shall comply with the Owens Corning current published instructions, using two (2) nails per shingle. Refer to Owens Corning published information on wind resistance and installation limitations, including the use of hand-sealing for wind warranties. 6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.3.3 Minimum Nailing—Berkshire" Hip&Ridge and High Ridge: Fig.t I i Fig.2 ` I D"celiianNal�/ �. _ i I 7oFVIeM SideViea Nails —� �•. \+-- I �-' Z. 'TOF Larvla:af I N it a ! >P. �— rr-- >, I I I 6.3.4 Minimum Nailing—WeatherGuard° HP Hip and Ridge: Fig.A 9 Fig.C Hip&Ridge Shingle Fastening PnzvaQlnq r'trlo q'-'� '. Top Vl+rl E—prectiF n n, Halls q to i I 1 • I I I I v v • �re S � EYposuna Exterior Research and Design,LLC. Evaluation Report 037940.02.12-RE Certificate of Authorization#9503 6EDITION(2017)FBC NON-HVHZ EVALUATION FL10674-1113 Owens Corning Asphalt Roof Shingles Revision 8:10/09/2017 Page 7 of 8 6 � � , \~ mERD 4/ TRINITY, 63.5 Minimum Nailing ProEdQe Hip&Ridge Shingles: Standard Prevailing Fastening Wind Direction s,,ant strip Pattern 12. sealant Fasten 71h, 6'Ex4pasur* Cover d RW Cement 636 Minimum NaU\ng—DucaRidge"Hip&Ridge Shingles: Note:The drawings below pertain to minimum,as-tested attachment requirements. Refer toOwe Ins Coming published installation instructions for their minimum requirements. TOP Yl� Na 7. Lxasums: 7.1 Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. 7] Asphalt shingle wrappers shall indicate compliance with one of the required classifications detailed in FB[ Table z5O7.2.7.1/R9nS.2.6.1. 8. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 9. K8mxUp4crnmmGPL4mTs: Contact the named OA entity for information on which plants produce products covered by F\ohda'Rv\e9N'3 CIA requirements. 10' QUALITY ASSURANCE ENTITY: ULLLC—WJ48G25 ;(63I) 546-2458; KanchiAgravva|a'Dokania@uicum - END OFEVALUATION REPORT- Exterior Research and Design,LLC. Evaluation Report o3/n4o.Oz�2-na Certificate of Authorization#9503 s—EDITION<zozr>pocmow'xv*ZEVALUATION pu0674-1113 Owens Corning Asphalt Roof Shingles ' Revision o:on/oy/zuz/ Page uo*a —