HomeMy WebLinkAboutProduct Approval (2) E
EN:m8��
5 XMEMO etc.
ion#32455
ty, PChriistian Street,ertificate tUn t#13
Oxford, CT 06478
(203) 262-9245
ENGINEER EVALUATE TEST CONSULT CERTIFY
EVALUATION O.
CertainTeed Corporation Evaluation Report 3520.03.04-1123
20 Moores Road FL2533-1122
Malvern, PA 19355 Date of Issuance:09/19/2005
(610)651-5847 Revision 23:04/17/2019
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for
compliance with the 6th Edition(2017) Florida Building Code sections noted herein.
DESCRIPTION: Flintlastic® Modified Bitumen Roof Systems
LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s)changes,the referenced
Quality Assurance documentation changes,or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E.of any changes to the
product(s),the Quality Assurance or the production facility location(s). NEMO I etc. requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "NEMO I etc. Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 6, plus a 67-page Appendix.
Prepared by:
`,\gyp:�;nq,,,�•',
Robert J.M.Nieminen .`=
, P.E. r�� �:=,?: The facsimile seal appearing was authorized by Robert
Florida Registration No.59166,Florida DCA ANE1983 ,�,;•„ �,',� Nieminen,P.E.on 04/17/2019.This does not serve as an
electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. NEMO ETC, LLC does not have,nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEMO ETC,LLC is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither NEMO I etc.nor Robert Nieminen,P.E.are,in any way,the Designer of Record for any project
on which this Evaluation Report,or previous versions thereof,is/was used for permitting or design guidance unless retained specifically
for that purpose.
'REVIEWED FOR
ODE COMPLIANCE �
FIS -
ST. LUCIE COUNTY ® y
BOCC I1 ao 9
NNEMOJetc.
ROOFING SYSTEMS EVALUATION:
Product Category: Roofing
Sub-Category: Modified Bitumen Roof Systems
Compliance Statement: Flintlastic° Modified Bitumen Roof Systems, as.produced by CertainTeed Corporation,
have demonstrated compliance with the following sections of the 6"Edition(2017)Florida Building Code through
testing in accordance with the following,Standards. Compliance is subject to the Installation Requirements and
Limitations/Conditions of Use set forth herein.
STANDARDS:
Section Property Standard Year
1504.3.1 Wind FM 4474 2011
1504.7 Impact FM 4470 2012
1507.11.2 Physical Properties ASTM D6162 2008
1507.11.2 Physical Properties ASTM D6163 2008
1507.11.2 Physical Properties ASTM D6164 2011
1507.11.2 Physical Properties ASTM D6222 2011
1507.11.2 Physical Properties ASTM D6509 2009
F3—. REFEREIVCES:
Entity Examination Reference Date
ERD(TST6049) FM 4470 3504.06.01-1 06/05/2001
ERD(TST6049) FM 4470 3513.08.02 08/15/2002
ERD(TST6049) FM 4470 03515.07.03 07/22/2003
ERD(TST6049) FM 4470 3519.12.03 12/22/2003
ERD(TST6049) FM 4470/4474 3522.07.04 07/28/2004'
ERD(TST6049) FM 4470/4474 02843.02.05-11 02/10/2005
ERD(TST6049) FM 4470/4474 3533.01.06 01/06/2006
ERD(TST6049) FM 4470/4474 4674.11.01-1 03/21/2006
ERD(TST6049) Physical Properties 3535.10.06 10/31/2006
ERD(TST6049) FM 4470/4474 3521.07.04-R1 10/26/2007
ERD(TST6049) FM 4470/4474 02764.09.05-111 12/10/2007
ERD(TST6049) FM 4470/4474 02762.03.05-R1 12/10/2007
ERD(TST6049) Physical Properties C7290.01.08 01/16/2008
ERD(TST6049) Physical Properties 010080.09.08 09/04/2008
ERD(TST6049) FM 4470/4474 C8370.08.08-111 10/05/2009
ERD(TST6049) FM 4470/4474 P6860.06.07-R1 09/10/2009
ERD(TST6049) FM 4470/4474 C30310.12.09 12/17/2009
ERD(TST6049) FM 4470/4474 C30560.03.10 03/18/2010
ERD(TST6049) FM 4470/4474 031420.08.10 09/21/2010
ERD(TST6049) FM 4470/4474 C33980.12.10 12/22/2010
ERD(TST6049) FM 4470/4474 C33830.02.11 02/08/2011
ERD(TST6049) TAS 117(B),Rupture C35500.02.11 02/09/2011
ERD(TST6049) FM 4470/4474 037820.07.12 07/24/2012
ERD(TST6049) FM 4470/4474 C37830.07.12 07/26/2012
ERD(TST6049) Physical Properties 042110.08.12 08/13/2012
ERD(TST6049) FM 4470/4474 C39670.08.12 08/20/2012
ERD(TST6049) FM 4470/4474 C42280.08.12 08/20/2012
ERD(TST6049) TAS 117(A) A35880.04.12-R1 10/26/2012
ERD(TST6049) FM 4470/4474 C44580.07.13 07/25/2013
ERD(TST6049) FM 4470/4474 C46090.11.13-A11/20/2013
ERD(TST6049) FM 4470/4474 C45620.03.14 03/27/2014
ERD(TST6049) FM 4470/4474 C46760.06.14 06/19/2014
ERD(TST6049) FM 4470/4474 C47320.03.14-R1 04/01/2015
ERD(TST6049) FM 4470/4474 CTR-SC8995.10.15 10/14/2015
ERD(TST6049) FM 4470/4474 CTR-SC9935.01.16 01/14/2016
ERD(TST6049) FM 4470 CTR-SC9920.01.16-R1 01/20/2016
ERD(TST6049) FM 4470/4474 CTR-SC10420.01.16 01/25/2016
ERD(TST6049) FM 4470/4474 CTR-SC9175.09.16-1 09/06/2016
ERD(TST6049) FM 4470/4474 CTR-SC9175.09.16-1 09/06/2016
,ERD(TST6049) FM 4470/4474 CTR-SC11590.08.16-R1 09/06/2016
NEMO ETC,LLC Evaluation Report 3520.03.04-RZ3
Certificate of Authorization#32455 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL2533-R22
CertainTeed Flintlastic®Modified Bitumen Roof Systems;(610)651-5847 Revision 23:04/17/2019 .
-Page 2 of 6
TRINITY I ERD
5.5 Allowable Roof Covers:
TABLE 1: ROOF COVEROPTIONS
Asphalt Wood Shakes
Underlayment Nail-On Tile Foam-On Tile Metal ' Slate
Shingles &Shingles
EasyLay UDL 15 Yes." No No Yes- Yes Yes
EasyLay UDL 30
(formerly"EasyLay® Yes No -- No Yes Yes Yes
UDL Basic")
EasyLay UDL 50 Yes., No. No Yes Yes Yes-. -
5.6 Exposure Limitations:
LeakBarrier EasyLay UDL 15 shall not be left exposed for longer than 30-days after installation.
LeakBarrier EasyLay UDL 30(formerly"LeakBarrier®EasyLay®UDL Basic)and LeakBarrier EasyLay UDL 50 shall not
be left exposed for longer than 180-days after installation.
6. INSTALLATION:
6.1 LeakBarrier EasyLay UDL Synthetic Roof Underlayments shall be installed in accordance with Tarco Roofing
published installation requirements subject to the Limitations set forth in Section 5 herein and the specifics noted
below.
6.2 Re-fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to
remove any dust and debris prior to application.
6.3 LeakBarrier EasyLay UDL 15,UDL 30(formerly"UDL Basic")or UDL 50:
6.3.1 Shall be installed in compliance with the requirements for ASTM D226, Type I or II underlayment in FBC Table
1507.1.1 or R905.1.1 for the type of prepared roof covering to be installed, taking into account the wider sheet-
width for double-layer applications.
6.3.2 For slopes 4:12 (18.4°) or greater: LeakBarrier EasyLay UDL Synthetic Roof Underlayments shall be laid
horizontally, parallel to the eave with the printed side up, flat and unwrinked and have minimum 4-inch side
(horizontal) laps and minimum 8-inch end (vertical) laps. Side(horizontal) laps shall run with the flow of water in a
shingling manner. End (vertical)laps shall be offset from course to course not less than 3 feet.
6.3.3 For slopes 2:12 (9.4°)to <4:12 (18.4°): LeakBarrier EasyLay UDL Synthetic Roof Underlayments shall be applied
in a double coverage method, flat and unwrinkled. Begin by applying a 24-inch wide starter-strip along the eaves.
Then place a full-width sheet over the starter, with the lower edge flush to the starter's lower edge. Apply
succeeding 48-inch wide courses up the roof slope, overlapping each previous course a minimum of 20-inches in a
"shingle fashion"with minimum 12-inch end (vertical) laps. End (vertical)laps shall be offset from course to course
not less than 3 feet.
6.3.4 Where laps or joints require sealant or adhesive use plastic cement recommended by Tarco Roofing. Tarco Roofing
recommends sealing all laps and joints where the underlayment will be exposed to wind-driven rain.
6.3.5 Attachment: Use corrosion-resistant or stainless steel roofing nails with 3/8-inch diameter heads or low-profile
plastic cap-nails with 1-inch diameter heads spaced 9-inch o.c. at all laps and 12-inch o.c. at two(2)staggered rows
in the field of the sheet. If wind or rain is expected prior to finished roofing application, use 1-inch diameter plastic
cap nails.
Code Reference: The Exception statement in FBC 1507.1.1 and FBC R905.1.1 requires use of metal cap nails where
the ultimate design wind speed,V,,,,equals or exceeds 150 mph.
NEMO ETC,LLC Evaluation Report 4930.02.14-R4
Certificate of Authorization 1/32455 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL16884-114
LeakBarrier EasyLay UDL Synthetic Roof Underlayments;(254)913-7750 Revision 4:02/14/2018
Page 3 of 4
TRINi-ryIERD
7. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
8. MANUFACTURING PLANTS:
Contact the noted QA agency for information on product locations covered for F.A.C. 611320-3 QA requirements.
The following plants have qualified products under their respective physical properties specifications.
Plant Specification Product(s)
LeakBarrier EasyLay UDL 15,LeakBarrier EasyLay UDL 30(formerly
Gujarat,India FBC 1507.1.1(Exception) "LeakBarrier®EasyLoy®UDL Basic"),LeakBarrier EasyLay®UDL 50
QUALITY9.
UL,LLC.—QUA9625;(414)248-6409;karen.buchmann@ul.com
-END OF EVALUATION REPORT-
NEMO ETC,LLC Evaluation Report 4930.02.14-114
Certificate of Authorization#32455 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL16884-R4
LeakBarrier EasyLay UDL Synthetic Roof Underlayments;(254)913-7750, Revision 4:02/14/2018
Page 4 of 4
S
N
MEMO etc.
5.1 This is a building code evaluation. Neither NEMOIetc. nor Robert Nieminen, P.E. are,in'any way,the Designer of
Record for any project on which this Evaluation Report,or previous versions thereof,is/was used for permitting or
design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in HVHZ jurisdictions.
5.3 This Evaluation Report does not purport to address codified fire requirements. Refer to a current Approved Roofing
Materials Directory for fire ratings of this product.
5.4 For steel deck installations,foam plastic insulation shall be separated from the building interior in accordance with
FBC 2603.4 unless the exceptions stated in FBC 2603.4.1 and 2603.6 apply.
5.5 The roof system evaluation herein pertains to above-deck roof components. Roof decks and structural members
shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. Load
resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation.
5.6 For recover installations,the existing roof shall be examined in accordance with FBC 1511.
5.7 For mechanically attached insulation or membrane or strip-bonded insulation,the maximum design pressure for
the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC Chapter
16. Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the
elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29,
Roofing Application Standard RAS 117 and Roofing Application Standard RAS 137. Assemblies marked with an
asterisk*carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29(January 2016)
for Zone 2/3 enhancements.
5.8 For assemblies with all components fully bonded in place,the maximum design pressure for the selected assembly
shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No rational analysis
is permitted for these systems.
5.9 For mechanically attached insulation or membrane over existing roof decks,fasteners shall be tested in the existing
deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the
minimum requirements for the system. Testing and analysis shall be in accordance with ANSI/SPRI FX-1 or Testing
Application Standard TAS 105.
5.10 For bonded insulation or membrane over existing substrates in a re-roof (tear off) or recover installation, the
existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If any
surface conditions exist that bring system performance into question, field uplift testing in accordance with
ANSI/SPRI IA-1,ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124 shall
be conducted on mock-ups of the proposed new roof assembly.
5.11 For bonded insulation or membrane over existing substrates in a recover installation,the existing roof system shall
be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having
Jurisdiction, as documented through field uplift testing in accordance with ASTM E907, FM Loss Prevention Data
Sheet 1-52 or Testing Application Standard TAS 124.
5.12 Metal edge attachment (except gutters), shall be designed and installed for wind loads in accordance with FBC
Chapter 16 and tested for resistance in accordance with ANSI/SPRI ES-1 or Roofing Application Standard RAS 111,
except the basic wind speed shall be determined from FBC Figure 1609.3(l),1609.3(2)or 1609.3(3).
5.13 All products in the roof assembly shall have quality assurance in accordance with FAC Rule 611320-3.
NEMO ETC,LLC Evaluation Report 3520.03.04-1123
Certificate of Authorization#32455 6-EDITION(2017)FBC NON-HVHZ EVALUATION FL2533-R22
CertainTeed Flintlastic®Modified Bitumen Roof Systems;(610)651-5847 Revision 23:04/17/2019
Page 5 of 6
U-
NNEMOletc.
6.1 Flintlastic® Modified Bitumen Roof Systems shall be installed in accordance with CertainTeed Corporation
published installation instructions,subject to the Limitations/Conditions of Use herein.
6.2 System attachment requirements for wind load resistance are set forth in Appendix 1. "MDP"=Maximum Design
Pressure is the result of testing for wind load resistance based on allowable wind loads, and reflects the ultimate
passing pressure divided by 2(the 2 to 1 margin of safety per FBC 1504.9 has already been applied). Refer to FBC
1609 for determination of design wind loads.
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
8. MANUFACTURING PLANTS: I
Contact the named QA entity for manufacturing facilities covered by F.A.C.Rule 611320-3 QA requirements.
-QUALITY
UL, LLC.—QUA9625;(414)248-6409, karen.buchmann@us.ul.com
-THE 67-PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT-
NEMO ETC,LLC Evaluation Report 3520.03.04 RZ3
Certificate ofAuthorization#32455 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL2533-R22
CertainTeed Flintlastic®Modified Bitumen Roof Systems;(610)651-5847 Revision 23:04/17/2019
Page 6 of 6
-' RECEIVED
NOV 15 15 2019 NEMO I etc.
Si-. Lucie County, Permitting Certificate of Authorization 1132455
3 Christian Street, Unit#13
Oxford,CT 06478
(203)262-9245
ENGINEER EVALUATE . TEST CONSULT CERTIFY
EVALUATION REPORT
Tarco Roofing Evaluation Report 4930.02.14-114
One Information Way,Suite 225 FL16884-114
Little Rock,AR 72202 Date of Issuance:02/27/2014
(254)913-7750 Revision 4:02/14/2018
SCOPE:
This Evaluation Report is issued under-Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 6th Edition (2017) Florida Building Code
sections noted herein.
DESCRIPTION: LeakBarrier EasyLay UDL Synthetic Roof Underlayments
LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes,the referenced
Quality Assurance documentation changes,or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. of any changes to
the product(s),the Quality Assurance or the production facility location(s). NEMO I etc. requires a complete review of
this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "NEMOJetc. Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed,then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 4.
Prepared by:
Robert J.M.Nieminen,P.E. The facsimile seal appearing was authorized byRobertNleminen,
'h;�Sg Y••�•"G''C P.E.on 02/14/2015.This does not serve as an electronically signed
Florida Registration No.59166,Florida DCAANE1983 �,,;� „,;:•'
document.
CERTIFICATION OF INDEPENDENCE:
1. NEMO ETC, LLC does not have, nor does it intend to acquire or will it acquire,a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEMO ETC,LLC is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E.does not have, nor will acquire,a financial interest in any other entity involved in the approval process of the
product. J
5. This is a building code evaluation. Neither NEMO Ietc. nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof,is/was used for permitting or design guidance unless retained
specifically for that purpose.
REVIEWED FOR -p��—o3o�
FILE C"'OPYCODE COMPLIANCE
ST. LUCIE COUNTY
BOCC
��TRINITYIERD
ROOFING COMPONENT EVALUATION:
1. ••
Product Category: Roofing
Sub-Category: Underlayment
Compliance Statement: LeakBarrier EasyLay UDL Synthetic Roof Underlayments, as produced by Tarco Roofing,
have demonstrated compliance with the following sections of the 6th Edition (2017) Florida Building Code through
testing in accordance with applicable sections the following Standards. Compliance is subject to the Installation
Requirements and Limitations/Conditions of Use set forth herein.
2. STANDARDS'
Section Property Standard Year
1507.1.1,R905.1.1 Exception Unrolling,Breaking Strength,Pliability ASTM D226 2009
1507.1.1,R905.1.1 Exception Tear Strength ASTM D1970 2015
1507.1.1,R905.1.1 Exception Tear Strength ASTM D4533 2015
TAS 110 Accelerated Weathering ASTM D4798 2011
3. REFERENCES:
Entity. Examination Reference Date
ERD(TST6049) Physical Properties SC4950.02.14 02/27/2014
ERD(TST6049) FBC 1507.1.1(Exception) TAR-SC16115.17 10/02/2017
UL,LLC(QUA9625) Quality Control Service Confirm,10227624 Exp.11/22/2019
PRODUCT4. DESCRIPTION:
4.1 LeakBarrier EasyLay UDL 15 consists of a woven-polymeric scrim with a textured fabric on the top surface; meets
FBC 1507.1.1&R905.1.1(Exception).
4.2 LeakBarrier EasyLay UDL 30(formerly"LeakBarrier®EasyLay®UDL Basic")consists of a woven-polymeric scrim with a
textured fabric on the top surface; meets FBC 1507.1.1&R905.1.1(Exception).
4.3 LeakBarrier EasyLay UDL 50 consists of a woven-polymeric scrim with a non-woven fabric on the top surface and
a rubberized polymeric coating on the back surface; meets FBC 1507.1.1&R905.1.1(Exception).
S. •
5.1 This is a building code evaluation. Neither NEW ETC, LLC nor Robert Nieminen, P.E. are, in any way,the Designer
of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting
or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 Fire Classification is not part of this report; refer to current Approved Roofing Materials Directory or test report
from accredited testing agency for fire ratings of this product.
5.4 LeakBarrier EasyLay UDL Synthetic Roof Underlayments may be used with any prepared roof cover where the
product is specifically referenced within FBC approval documents. If not listed, a request may be made to the
Authority Having Jurisdiction for approval based on this evaluation combined with supporting data for the prepared
roof covering.
NEMO ETC,LLC Evaluation Report 4930.02.14-R4
Certificate ofAuthorization 1132455 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL16884-Re.
LeakBarrier EasyLay UDLSynthetic Roof Underlayments;(254)913-7750 Revision 4:02/14/i.0.18'' -
Page 2 of 4
Y�
O
NEMO etc.
Entity Examination Reference Date
ERD(TST6049) FM 4470/4474 CTR-SC12255.12.16 12/27/2016
ERD(TST6049) Criticality ICP-SC15630.09.17 09/06/2017
ERD(TST6049) Criticality ICP-SC16225.09.17 09/06/2017
ERD(TST6049) FM 4474 CRT-SC15775.17 09/13/2017
FM Approvals(TST1867) FM 4470 OE3A2.AM 03/30/1982
FM Approvals(TST1867) FM 4470 3WOA4.AM 03/16/1993
FM Approvals(TST1867) FM 4470 3WOA2.AM 03/17/1993
FM Approvals(TST1867) FM 4470 3WOA3.AM 03/17/1993
FM Approvals(TST1867) FM 4470 1Z4A6.AM 09/11/1996
FM Approvals(TST1867) FM 4470 3Y8A1.AM 09/30/1996
FM Approvals(TST1867) FM 4470 2D5A9.AM 06/22/1999
FM Approvals(TST1867) FM 4470 3009502 12/12/2000
FM Approvals(TST1867) FM 4470 3008869 03/19/2001
FM Approvals(TST1867) FM 4470 3009610 10/15/2001
FM Approvals(TST1867) FM 4470 3006025 12/28/2001
FM Approvals(TST1867) FM 4470 3012321 07/29/2002
FM Approvals(TST1867) FM 4470 3009814 09/06/2002
FM Approvals(TST1867) FM 4470 3014502 04/04/2003
FM Approvals(TST1867) FM 4470 3015444 07/11/2003
FM Approvals(TST1867) FM 4470 3014692 08/05/2003
FM Approvals(TST1867) FM 4470 3014751 08/27/2003
FM Approvals(TST1867) FM 4470 3018579 10/09/2003
FM Approvals(TST1867) FM 4470/4474 3020703 07/30/2004
FM Approvals(TST1867) FM 4470/4474 3021759 06/03/2005
FM Approvals(TST1867) FM 4470/4474 3022038 04/05/2006
FM Approvals(TST1867) FM 4470/4474 3023458 07/18/2006
FM Approvals(TST1867) FM 4470/4474 3026128 08/04/2006
FM Approvals(TST1867) FM 4470/4474 3024311 11/01/2006
FM Approvals(TST1867) FM 4470/4474 3025766 11/13/2006
FM Approvals(TST1867) FM 4470/4474 3028410 02/19/2007
FM Approvals(TST1867) FM 4470/4474 3026964 07/25/2007
FM Approvals(TST1867) FM 4470/4474 3031262 11/30/2007
FM Approvals(TST1867) FM 4470/4474 3031199 12/23/2008
FM Approvals(TST1867) FM 4470/4474 3032172 06/12/2009
FM Approvals(TST1867) FM 4470/4474 3037127 01/11/2010
FM Approvals(TST1867) FM 4470/4474 3039848 12/02/2011
FM Approvals(TST1867) FM 4470/4474 3046104 08/13/2013
FM Approvals(TST1867) FM 4470/4474 3048520 09/19/2013
FM Approvals(TST1867) FM 4470/4474 3055491 12/05/2016
FM Approvals(TST1867) FM 4470/4474 3063970 09/14/2018
MTI(TST2508) Physical properties DX08C4A 03/22/2004
MTI(TST2508) Physical properties DX20E3A 03/22/2004
MTI(TST2508) Physical properties DX2OE3A-001 01/04/2006
MTI(TST2508) Physical properties AX31G8A 08/21/2008
MTI(TST2508) Physical properties AX31G8D 09/05/2008
MTI(TST2508) Physical properties AX31G8F 06/05/2009
MTI(TST2508) Physical properties AX21G8C 01/28/2011
NEMO(TST6049) FM 4474 4L-CTR-18-002.09.18-1;CTR-Cl,C2 09/21/2018
NEMO(TST6049) FM 4474 4L-CTR-18-002.09.18-2;CTR-C3 09/21/2018
NEMO(T5T6049) FM 4474 4L-CTR-18-002.10.18;CTR-Al,A2,C4 10/22/2018
NEMO(TST6049) FM 4474 4L-CTR-18-002.03.19A;CTR-05 TO C8 03/07/2019
NEMO(T5T6049) FM 4474 4L-CTR-18-002.04.198;CTR-C11 04/12/2019
NEMO(TST6049) FM 4474 2L-CTR-18-001;CTR-C9&CTR-C10 04/17/2019
PRI(TST5878) Physical Properties' CTC-032-02-01 01/16/2008
PRI(TST5878) Physical Properties CTC-034-02-01 11/24/2008
PRI(TST5878) Physical Properties CTC-066-02-01 08/08/2011
PRI(TST5878) Physical Properties CTC-067-02-01 08/08/2011
PRI(TST5878) Physical Properties CTC-068-02-01 08/08/2011
PRI(TST5878) Physical Properties CTC-070-02-01 08/08/2011
PRI(TST5878) Physical Properties CTC-071-02-01 08/08/2011
PRI(TST5878) Physical Properties CTC-093-02-01 08/08/2011
PRI(TST5878) Physical Properties CTC-116-02-01 04/03/2012
PRI(TST5878) Physical Properties CTC-183-02-01 10/04/2013
PRI(TST5878) Physical Properties CTC-259-02-01 12/11/2015
UL,LLC.(QUA9625) Quality Assurance Service,Confirmation,R11656 03/09/2017
NEMO ETC,LLC Evaluation Report 3520.03.04-1123
Certificate o/Authorization 832455 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL2533-R22
CertainTeed Flintlastic®Modified Bitumen Roof Systems;(610)651-5847 Revision 23:04/17/2019
Page 3 of 6
OC
MEMO I etc.
PRODUCT DESCRIPTION:
This Evaluation Report covers Flintlastic® Modified Bitumen Roof Systems installed in accordance with
CertainTeed Corporation published installation instructions and the Limitations/ Conditions of Use herein. The
following CertainTeed products make up the subject systems.
TABLE 1:ROLL-GOODS FOR FLINTLASTICO MODIFIED BITUMEN ROOF SYSTEMS
TYPE PRODUCT SPECIFICATION
REFERENCE GRADE TYPE
Flintlastic®SA NailBase ASTM D4601 N/A II
GlasbaseTm Base Sheet ASTM D4601 N/A II
All Weather/Empire'"Base ASTM D4601 N/A II
Base Sheets FlexiglasT'Base ASTM D4601 N/A II
Flintlastic"'Base 20 ASTM D4601 N/A II
Flintlastic Poly SMS Base Sheet ASTM D4601 N/A II
Yosemite®Venting Base ASTM D4897 N/A II
Ply Sheets Flintglas®Ply 4 ASTM D2178 N/A IV
Flintglas®Premium Ply 6 ASTM D2178 N/A VI
Flintlastic®APP Base T ASTM D6509 N/A N/A
Base/Ply Membranes(APP) Flintlastic®STA ASTM D6222 S I
Flintlastic°STA Plus ASTM D6222 S I
Flintlastic®STA ASTM D6222 S I
Flintlastic°STA Plus ASTM D6222 S I
Cap Membranes(APP) Flintlastic®GTA ASTM D6222 G I
Flintlastic®GTA CoolStar'" ASTM D6222 G I
Flintlastic®GTA-FR ASTM D6222 G I
Flintlastic®GTA-FR CoolStar'" ASTM D6222 G I
Flintlastic°SA PlyBase ASTM D1970 N/A N/A
Black Diamond®Base Sheet ASTM D1970 N/A N/A
Flintlastic°SA Mid Ply ASTM D6163 S I
Base/Ply Membranes(SBS) Flintlastic°Ultra Glass SA ASTM D6163 S I
Flintlastic°Base 20 ASTM D6163 S I
Flintlastic Base 20 T ASTM D6163 S I
Flintlastic°Ultra Poly SMS Base Sheet ASTM D6164 S I
Flintlastic°FR Dual Cap ASTM D6162 G I
Flintlastic SA Cap FR ASTM D6163 G I
Flintlastic°FR Cap 30 ASTM D6163 G I
Flintlastic°FR Cap 30 CoolStar'" ASTM D6163 G I
Flintlastic FR Cap 30 T ASTM D6163 G I
Flintlastic°FR Cap 30 T CoolStarT"" ASTM D6163 G I
Cap Membranes(SBS) Flintlastic°SA Cap ASTM D6164 G I
Flintlastic°FR-P ASTM D6164 G I
Flintlastic°FR-P CoolStar'' ASTM D6164 G I
Flintlastic°GMS ASTM D6164 G I
Flintlastic°GMS CoolStar'" ASTM D6164 G I
Flintlastic°GTS-FR ASTM D6164 G II
Flintlastic°Premium FR-P ASTM D6164 G II
NEMO ETC,LLC Evaluation Report 3520.03.04-R23
Certificate of Authorization#32455 6T"EDITION(2017)FBC NON-HVHZ EVALUATION F1.2533-1122
CertainTeed Flintlastic®Modified Bitumen Roof Systems;(610)651-5847 Revision 23:04/17/2019
Page 4 of 6