HomeMy WebLinkAboutNOA, Underlayments i
RECEtvEo
SOV 2� 1019
artmen< I
MIMMIDWEMIAMI-DART;COUN I Y
Em
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami-,Flotida,33175-2474
T(786)515-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidudc. ovleconomv
Polyglass USA Inc.
1111 W.Newport Center Drive
Deerfield Beach,FL 33442.
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami-Dade County and other areas where.allowed by.the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control.Section
(in Miami-Dade. County)and/or the AHJ(in areas other than Miami-Dade County)reserve the right to have this
product or material tested for quality assurance purposes.If-this product or material fails to perform in the accepted!
manner;the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance;
ifitis.determined by Miami-Dade County Product Control Section that this-product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein,and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION*.Polyglass Polystick Underlayments
LABELING: Each unit shall bear a permanent label with.the manufacturer's name or.logo,city,state and following
statement:"Miami-Dade County Product Control Approved';unless otherwise noted herein.
RENEWAL of.this NOA shall be considered after a renewal applicatioirhas been filed and there has'bee_n no change
in the applicable building code negatively affecting the performance ofthis product.
TERMINATION;of this NOA will occur after the expiration date or if there has been a revision or change-in the
materials,use,And/or.Manufacture of the product or process.Misuse of this-NOA as an endorsement of any produc
.for:sales,advertising or any other purposes shall automatically tenninate this NOA.Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT:The NOA number preceded by the words Miami-DadeCounty, Florida, and followed.
by the expiration date may be-displayed 'in advertising literature. If any portion of.the NOA is displayed,then
it shall be done in its entirety.
i
INSPECTION:A copy of this.entire NOA shall be provided to the user by the manufacturer-or its distributors and
shall be available for inspection at the job site at therequest of the Building Official.
This NOA renews and revises NOA No.14-;0717.08 and consists of pages 1 through S.
The submitted documentation was reviewed by Gaspar J Rodriguez.
File Copy
I
I
e4u K=r=cfl4416LED'FOR NOA No.: 15-0410.04
.� �'®®� �� Expiration Date: 09/13/21
— ® COMPLIANCE Approval Date: 08/11/16
STmIUCIE COUNTY Y Pagel sof 8
i3c)c
ROOFING COMPONENT APPROVAL
Category Roofing
Sub-Category: Underlayment
Material: SBS -,.APP Self-Adhering Modified Bitumen
PRODUCTS DESCRIPTION:
I
Test Product
Product. Dimensions Specification Descrintion
Polystick IR-Xe 65'.x TVA" ASTM-D 1970 A fine granularlsand top surface self-adhering,APP
Or 65'x 3' polymer modified,fiberglass reinforced,bituminous
Manufacturing
Location#1 &_#2 60 mils thick sheet material for.use as an underlayment it sloped.roof
assemblies. Designed as'an ice:&rain.shield.
Polystick.Dual Pro 61':x 3'3 3/8" TAS 103 and A rubberized asphalt self-'adhering,glass.-fiber/polyester
Manufacturing 60 mils thick ASTM-D 1970 reinforced waterproofing membrane. Designed as.a
Location
Manufacturing
metal roofing and roof tile underlayment.
Polystick Tile Pro 61'x.3'-3'/8" TAS 103 and A rubberized asphalt self-adhering,glass-fiber/polyester
Manufacturing 60..mils thick ASTM D 1970 reinforced waterproofing membrane.Designed as a metal
Location 92 roofing.and roof tile underlayment.
Polystick TU Mas 65'8"'x 3'3-3/8" TAS.-103 and A rubberized asphalt self adhering;polyester reinforced_
Marrufagtwi in— 60 mils thick ASTM.D 1979 waterproofing membrane: Designed as a a roof tile
-
Location#1'
Polystick_TU? 3210"x 3'3 i" TAS 103 and A rubberized asphalt waterproofing membrane,glassi
Manufacturing 130 mils thick ASTM D 1970 fiber/polyester reinforced,,with a granular surface
Location#2 designed for use as a tile roof underlayment.
Polystick TU Plus 65'x 3'3 3/s" TAS 103 and A rubberized asphalt self-adhering,glass-fiber/polyester
(Surface Printing) 80 mils thick ASTM D 1970 reinforced waterproofingmembrane..Designed as a metal
Manufacturing roofing and-roof file underlayment.
Location.#1 
Polystick MTS 65'8"x 3'3 3/8" TAS 103 A homogeneous,rubberized asphalt waterproofing
60 mils thick membrane,glass fiber reinforced with.polyolefinic'f im
Manufacturing - --
Location#2 on the upper surface for use as an underlayment for metal
roofing,roof tile;slate.tiles and shingle underlayment
Polystick MTS_Plus -65'8"x TVA" TAS 103 A homogeneous,,rubberized.asphalt waterproofing
Manufacturing
60 mils thick membrane,glass-fiber reinforced with polyolefinic film
�
Location#2
on the upper surface for use as an underlayment for metal
roofing,roof tile,slate tiles and shingle.underlayment.
Elastoflex S6-G: 32'10"x 3'3-%" TAS 103 and. Polyester reinforced,SBS modified bitumen=membr l e
Manufacturing ASTM D 6164 with a sanded back face and a-granule top surface. For
Location#2 use in roof tile underlayment systems.
NOA No.: 15-0410.04
P41RL 187AF]E c°urmr Expiration Date: 09/13/21
IUM Approval Date: 08/11/16
Page:2 of.8
I
MANUFACTURING PLANTS:
1. Hazelton,PA
2. Winter Haven, FL
EVIDENCE SUBMITTED
Test Agency Test Identifier Test Name/Report Date
Trinity ERD P10870.09.08-R] TAS 103 12/04/08
P10870.04.09 TAS 103/ASTM D4798&G155 04/13/09
P33360.06.10 ASTM D1970 07/01/16
P33370.03.11 TAS 103 03/02/111
P33370.04.11 ASTM D 1623 04/26/11
P36900.09.11 TAS 103/ASTM D4798 &G155 09/01/11
P37300.10.11 TAS 110/ASTM D4798&D1970 10/19/11
P40390.08.12-2 ASTM D 1623 08/07/12
P37590.07.13-1 ASTM D6164 07/02/13
P45270.05.14 TAS 103,TAS 110&ASTM D1623 05/12/14
P46520.10.14 ASTM D1623 10/03/14
P44360.10.14 TAS 103&TAS 110 10/07/14
P43290.10.14 ASTM D 1970&TAS 110 10/17/14
PLYG-SCI0130.06.16-3 TAS 103&TAS 110 06/27/16
PLYG-10130.06.16-1 ASTM D1970&TAS 110 06/27/16
i
PRI Asphalt Technologies PUSA-035-02-01 TAS 103 09/29/06
PUSA-055-02-02 TAS 103 12/10/07
PUSA-089-02-01 TAS 103/ASTM D4798&G155 07/06/0
Momentum Technologies,Inc. JX20H7A TAS 103/ASTM D4798&G155 04/01/08
RX14E8A TAS 103/ASTM D4798&G155 11/09/09
DX23D8B TAS 1'03/ASTM D4798&G155 02/18/16
DX23DSA TAS 103/ASTM D4798&G155 02/18110
LABELING:
1. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo,city
and state of manufacturing facility and the following statement: "Miami-Dade County Product Control Approved"
or the Miami-Dade County Product Control Seal as shown below.
MIAMMADEC®�
BUILDING PERMIT REQUIREMENTS:
1
Application for building permit shall be accompanied by copies of the following:
1.This Notice of Acceptance.
2.Any other documents required by the Building Official or applicable building code in order to properly evaluate the
installation of this materials.
co r NOA No.: 15-04]0.04
Expiration Date: 09/13/21
Approval Date: 08/11/16
Page 3 of 8
' I
INSTALLATION PROCEDURES:
DeciliType 1: Wood,non-insulated
-Deck'Description: Min. 19/32".plywood or wood-pld-nk
System Type E(l):, Anchor sheet mechanically fast6ned to deck;_-
Anchor/Base Sheet: One-or more plies of ASTM-D 226 Type Ror ASTM'D-2626
1" .
Fastening: Per FBC 15.18.2,& 018A Nails and tin caps T21 grid,6o.c.at,'a minimum 4"head lap (for
base.sheet only)
Membrane Polyst ick IR Xe,Po1vstiek Dual,Pro,Polystick Tile Pro,PolystickTU*Max-,Polystie'
TU P,Polystick TU P1119 P ck-MTS&Volys k'W$Plus;-self adhered.: i
Surfacing:. See.defieral Limitations Below:
Do&Type 1:: Wbo'd,no...n. 4nsulated
Deck-Desgri ion� Min.
Pt -:19/32" ply.w.o6do-rwood plank
System Type E(2): Anchor sheet medhanic-ally,fastengd.tp deqlq ThOrhbraneAdhered,
Anchor/Base Sheet: One.ormore- plies Of ASTM--D 226 Type 11 or;
ASTM D:2626.
Fastening: Per FBC 1518.2&:15:18.4 Nail- andtin cap a 4mi4imum lap.
s - 4 iT�grid,6"o.c. 't- .0 _4"head
base:sheet,only)
Membrane: Elastoflex S6 G,hot asphalt applied
_Surfacing: Se&Gcneral-Urnit-ationsBelow.
D&k Tvve:1: Wood I s ,
nbn-ift ulated
Dodkbeser-lp.604: 19/32"plywood or wood plank.
System Type E(3): Base sheet mechanically fastened to deck,stibsequent cap-membrane self-adhered.
Angkor/Base Sheet- One:6r mote plies of ASTM D 226 Type I1'or,ASTM D 2626.
Fastening: Per FBC 1518.2-2& 1519.4 Nails and tin caps 11"vid,6"-o.cat a minimum 4'-'head lap or
base sheet only)
Ply-Sheet:. Polystick MTS Plus.self: dhered With minimum,31"horizontal laps and.iniiihnumi6".vertical
laps.
Membrane:: Polystigk TU-Plu- s,:§elf-adhekcd.
`Surfacifig. See General Lirnit#i.6fts,9.eloWi
NOA No.: 15-0410.04
lrEIl4NA =ECOi1Pt3Y Expiration Date: 09/i3/21.
I 'I
Approval Date: 08/11/16
Page 41of 8'
'INSTALLATION REQUIREMENTS:
A, All nails din the deck-shall:becarefully checked.for protruding heads. Re-fasten any loose deck:,panels,and
sweep the deck-thoroughly to.remove any dust and debris,prior to,application.
2:, Place the underlayment;over metal drip edge-in,accordance With-RASA I I
3: Place,the first course of membrane parallel to the eave,rolling the'riiembrane to obtain maximum.contact.
Remove the release film as themembrane is applied. All side laps shall be.a:minimum_of V/2"and end laps
shaIla e a minimum of 6", Roll the membrane into.place,after removin the release strip. Vertical strapping of
the roofwithis acceptable. Membrane shall be back nailed inaccordance wth_applicable building.
code.
4. When'apply,ing the membrane in the valley;start at the low point land.workto the high point,rolling the
membrane from the center outward in both-'directions:
5. For ridge applications,center the membrane and roll from the Center outward;in both directions..
6. Rollor broom=the entire membrane surface so as.to have.full contact with the;surface,givingspecial attention
to lap areas..
7. Flash Vent pipes,stacks;chimney_s and penetrations in-compliance:`with Roof Assembly.current Product Control
Notice of Acceptance.:
8. All protrusions or drains shall be initially.taped;with a 6"piece.of'underlayment. The flashing tape shall be
pressed in place�and formed;around thp-protrusion to ensure a tight fit: A`second layer of Polystick shall be;
applied over the.underlayment.
GENERAL LIIVIITATIQNS:
1. Fire classification is:not part of this-966'ptance.
2. Polystick Oual Pro,Polystick`Tde Pro,Polystick TU Plus,Polystick MTS and Polystick MTS Plus may'be
used in asphaltic shingles,wood-shakes and shingles,non-structural metal roofing,roof file systems and quairy
slate roof assemblies:.
Polystick TU P may be used in all the previous-assemblies-listed exceptmetal roofing.
Polystick IR Xe'may be used in all the previous assemblies listed except metal.roofing.and:roof tile systems.
Polystick TU.Maa may be used mnon=structural metal"roofing;jh&roof the systems.
Elastoflex S6 G may be used in roof tile systems only.
3. Deck requirements shall:be in compliance with applicable building code.
4. Polystick IR-Xe,Polystick Dual:Pro,Polystick Tile Pro,Polystick TU.Max,Polystick TU P,Polystick TU
Plus,Polystick MTS and Polystick NITS Plus shall be applied to a smooth,clean and dry surface. The deck
shall be free of irregularities.
5; Polystick.IR-Xe,Polystick Dual Pro;Polystick Tile Pro,Polystick TU 1VIax;Polystick TU P Polystick TU
Plus,Polystick-MTS and Polystick MTS Plus shall not be adhered_d rectly.over a pre-existing roof membrane
as a.recover system.
6. Polystick IR-X-,Polyst ckDnal Pro,.Polystick Tile Pro,Polystick TU Max,,Polystick TU P,Polystick TU
Plus,Polystick MTS and.Polystiek'MTS Plus shall be left.exposed as:a temporary roof for longe_r'than'the
amount of days listed in thetable below after:.application:.Polyglass reserves:the rightao revise or alter product
exposure times:not,to exceed the preceeding-maximumtime limitations.
Ex_osure Limitationsa s
MTS IR-Xe Elastotle-x TU TU_P He Pro Dual Pro TUAtax MTS A us
S6 G Plus
Winter Haven,FL 180 - 90 180 180 180 180 180 180 180.1
Hazelton;PA N/A . 90 Nh4 180 N/A N/A N/A 180: N/Al
=EC(jUPM
NOANo- 15-0410.04.Expiration Date._.09/13/21
Approval Dater 08/h/,16
Page 5;of 9
i
p quality � accordance with.the Florida Building Code and
7., All products'listed her shall have a uali assurance audit in
Rule 6.1 G- 16-3 of the Florida Administrative Code.
In-roof tile,application,-,data for-the attachment resistance of roof tiles shall be as set forth-in the-roof tile
malnufacturer?sNot,1deto of
Polystick TU Max,Polystick-TU Plus or Elastoflex' G:S6 may tie used in:both adhesi
Polystick Tile Prove
set and mechanicaHv'fastened roof tile applications:
Polystick Dual Pro i§.-limited.to mechanically fastened roof.tile applications, j
Polystck.MTS and Polystick MTS Plus.are limited to mechanically fastened with the limitations outlined in
Section 9.
Polystick TU P maybe used-in mechanically fastened roof file applications with the ekception:of mortal settile
applications.
e y. ( )
9: When loadin roof tiles on roof file underla ment for 'di
_ rect to-deck dile.assemblies,.the maximum,roof slo pe
shall be as follows:(See`Table Belo w)
Tile Profile Poly_stick MTS Elastofleg Polystick TU Plus,TU-P, Polyst ck Polystick
S6 G Tile Pro,Dual Pro: TU Maio MTS Plus
Plat Tile Prohibited 4:12 6:12 6;12 5-12'
without battens.-
Profiled Tile Prohibited 4.12. 6:12 4:12
without battens
The above slope limitations canoe=exceeded only by using-battens in accordance.with the Approved'Tile System
Notice of Acceptance and applicable Florida.Building.CoIde requireme,nts. When battens are required,they shall
. _ . _
be utilized during loading and°installation of tiles.
10. Care should:be taken;during the lgadi ig.Procedure to keep foot traffic to a minimum and to avoid dropping of
Iile directly,on the underlayment Refer to Polyglass'Tile loading'detail below for loading procedure two tiles
laid perpendicular to.slope followed by a maximum four tile stackparallel to the slope,for a total of 6tiles—,�or
all.:uriderlayme-nts except Polystick MTS.which shail'be loaded onto battens.
Robflhg Tiles
= (6 Max Per Stack) -
a 12
0 6�—
t0 -
13of Deck prepared lith
F LWfic lU Pigs:
� {I
I
NOA No.:' 15-0410.04
lias+°e€�utrnr Expiration Date:' 09/ !3/21
Approval Date: 08/111/16
Page& f 8:
1 ' i
I1. Refer to prepared roofing system Product Control Notice of Acceptance for listed approval of this product with
specific prepared roofing products. Polystick IR-Xe,Polystick Dual Pro,Polystick Tile Pro,PoIystiek TU
Max,Polystick TU P,Polystick TU Plus,Polystick MTS,Polystick MTS Plus or Elastoflex S6 G may be
used with any approved roof covering Notice of Acceptance listing Polystick IR-Xe,Polystick Dual Pro,
Polystick Tile Pro,Polystick TU Max,Polystick TU P,Polystick TU Plus,Polystick MTS,Polystick MTS
Plus or Elastoflex S6 G as a component part of an assembly in the Notice of Acceptance.
If Polystick IR-Xe,Polystick Dual Pro,Polystick Tile Pro,Polystick TU Max,Polystick TU P,Polystick
TU Plus,Polystick MTS,Polystick MTS Plus or Elastoflex S6 G are not listed,a request may be made to the
Authority Having Jurisdiction(AHJ)or the Miami-Dade County Product Control Section for approval provided
that appropriate documentation is provided to detail compatibility of the products,wind uplift resistance,and fire
testing results.
POLYGLASS GENERAL APPLICATION GUIDELINES FOR POLYSTICK MEMBRANES
PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC APPLICATIONS.
LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS.
1. Polyglass does accept the direct application of Polystick underlayment membranes to wood decks. Installers!are
cautioned to refer to applicable local building codes prior to direct deck installation to ensure this is acceptable.
Please also refer to applicable Product Data Sheets of the corresponding products.
2. All rolls,with the exception of Polystick TU Plus should be back-nailed in selvage edge seam as per Polyglass
Back Nailing Guide. Nails shall be,l l gauge ring shank type,applied with a minimum I %" metal disk as
required in Miami-Dade County or simplex type nail as otherwise allowable in other regions,at a minimum rate
of 12"o.c. Polystick TU Plus should be back nailed in designated area marked"nail area,area para clavae'on
the face of membrane,with the above stated nails and/or disks.The head lap membrane is to cover the area being
back-nailed.(Please refer to applicable local building codes prior to installation.)
3. All seal lap seams(selvage laps)must be rolled with a hand roller to ensure full contact.
4. All fabric over fabric;and granule over granule end laps,shall have a 6"wide,uniform layer of Polyglass
Polyplus 55 Premium Modified Flashing Cement,Polyglass Polyplus 50 Premium MB Flashing Cement,
XtraFlex 50 Premium Modified Wet/Dry Cement,Polyglass PG500 MB Flashing Cement,applied in between
the application of the lap.The use of mastic between the laps does not apply to Polystick MTS.
5. A maximum of 6 tiles per stack are allowed when loading tile on the underlayments.Refer to the Polyglass Tile
Loading Guidelines.See General Limitations#9 and#10.
6. Battens and/or Counter-battens,as required by the the manufacturers NOA,must be used on all projects for
pitch/slopes of 7"/12"or greater. It is suggested that on pitch/slopes in excess of 6 '/4'/12",precautions should be
taken,such as the use of battens to prevent file sliding during the loading process.
7. Minimum cure time after membrane installation&,before loading of roofing tiles is Forty-Eight(48)Hours.
8. Polystick membranes may not be used in any exposed application such as crickets,exposed valleys,or exposed
roof to wall details.
9. Repair of Polystick membranes is to be accomplished by applying Polyglass Polyplus 55 Premium Modif ed
Flashing Cement,Polyglass Polyplus 50 Premium MB Flashing Cement,XtraFlex 50 Premium Modified j
Wet/Dry Cement, Polyglass PG500 MB Flashing Cement to the area in need of repair,followed by a patch of the
Polystick material of Iike kind should be set and hand rolled in place over the area needing such repair. Patching
membrane shall be a minimum of 6 inches in either direction. The repair should be installed in such a way so
that water will run parallel to or over the top of all laps of the patch.
NOA No.: 15-0410.04
atas Expiration Date: 09/13/21
Approval Date: 08/11/16
Page 7�of 8
I
I
i • I
I
i
10. All self-adhered membranes must be rolled to ensure full contact with approved substrates. Polyglass requires a
minimum of 40 lbs for a weighted roller for the rolling of the Feld membrane. Hand rollers are acceptable fob
rolling of patches or small areas of the roof. Brooming may be used where slope prohibits rolling.
11. All approved substrates should be dry,clean and properly prepared,before any application of Polystick
membranes commences. An approved substrate technical bulletin'can be furnished upon request.It is 1
recommended to refer to applicable building codes prior to installation to verify acceptable substrates.
12. The Polyglass Miami-Dade Notice of Acceptance(NOA)approval for Polystick membranes can be furnished
upon request by our Technical Services Department by calling l (800)8944563.
13. Questions in regards to the application of Polyglass products should be directed to our Technical Services
Department at 1 (800)894-4563.
14. Polyglass recommends that applicators follow good roofing practices and applicable procedures as outlined b
the National Roofing Contractors Association(NBCA).
PLEASE CHECK WITH LOCAL iBUILDING CODES REGARDING LIMITATIONS OF SPECIFIC APPLICATIONS.
LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOIVIMENDATIONS. .
END OF THIS ACCEPTANCE
NOA No.: 15-0410.04
Expiration Date: 09!13/21
Approval Date: 08/111/16
Page 8 of 8
I