HomeMy WebLinkAboutProduct Approval CREEK JOHNS MANVILLE CORPORATION
PVC&TPO Single Ply Roofing Systems
TECHNICAL SERVICES. LLC APPENDIX C —APPROVED ASSEMBLIES FOR JIM TPO SINGLE-PLY MEMBRANES
Mechanically Fastened Assemblies over Steel Deck New, Existin , or Recover
System Deck Base Base Top Top Insulation
Membrane Membrane emrane Attachment MDP
No. Detail Insulation Insulation Attachment (pso
Attachment
OPTIONAL Preliminarily 37.5
S-M-4 G33. F.L6, INSULATION Secured or OPTIONAL JM TPO Attached in-lap 12-inch o.c.with (Lim.7;
S24 under min, secured with top Cover Board Preliminarily Secured HL Fasteners&Plat(Min.60 mil) es;
1.5-inch E3 layer Fastener rows max.90-inch inch o.c. H
OPTIONAL Preliminarily HV
5
S-M-S G33, H1, INSULATION Secured or OPTIONAL JM TPO Attached in-lap 12-inch o.c.with (Lim.7;
L6. SH24 under min. secured with top Cover Board Preliminarily Secured (Min.60 mil) HL Fasteners&Plates: Non-
1.5-inch E3 layer Fastener rows max. 90-inch o.c. HVHZ
OPTIONAL Preliminarily (-30
S-M-6 G33. P, L6, INSULATION Secured or OPTIONAL JM TPO Attached in-lap 12-inch o.c.with
Preliminarily Secured Extra HL Fasteners&Plates. Lim.7;
S24 under min. secured with top Cover Board (Min.60 mil)
1.5-inch E3 layer Fastener rows max. 138-inch o.c. Non-
HVHZ)
OPTIONAL Preliminarily
G33, P. L6, INSULATION Secured or OPTIONAL Attached in-lap 12-inch o.c.with
S-M-7 Preliminarily Secured JM 60 HL Fasteners&Plates; (45
S24 under min. secured with top Cover Board (Min.60 mil) Lim 7)
1.5-inch E3 layer Fastener rows max.66-inch o.c.
OPTIONAL Preliminarily Attached in-lap 12-inch o.c.with
S-M-B G80, F2W. INSULATION Secured or OPTIONAL High Load Fasteners and JM -45
L6, S24 under min. secured with top Cover Board Preliminarily Secured JM TPO
High Load Plus Plates; (Lim.7)
OPTIONAL Preliminn
1-inch la Fastener rows max.90-inch o.c.
arily
S-M-9
G80.F1, INSULATION Secured or OPTIONAL JM TPO or Attached in-lap 12-inch o.c.with L6. S18 under min, secured with top Cover Board Preliminarily Secured JM TPO FB Extra HL Fasteners&Plates; -45
1.5-inch E3 layer
Fastener rows max. 114-inch o.c. (Lim.7)
OPTIONAL Preliminarily
S-M-10
G80. F1. INSULATION Secured or OPTIONAL JM TPO or Preliminarily �5
Attached in-lap 6-inch o.c.with
L6. S18 under min. secured with top Cover Board
Secured JM TPO FB HL Fasteners&Plates: (Lim.7)
1.5-inch E3 layer Fastener rows max. 114-inch o.c.
OPTIONAL Preliminarily
S-M-11 G80, F1. INSULATION Secured or OPTIONAL Attached in-lap 6-inch o.c.with
Preliminarily Secured JM TPO or -52.5
L6. S18 under min. secured with top Cover Board y JM TPO FB Extra HL Fasteners&Plates; (Lim.7)
1.5-inch E3 la er Fastener rows max. 114-inch o.c.
OPTIONAL Preliminarily
S-M-12 G80.F1, INSULATION Secured or OPTIONAL Attached in-lap 6-inch o.c.with 60
L6, S18 under min, secured with top Cover Board Preliminarily Secured JM TPO HL Fasteners&Plates;
1.5-inch E3 layer
Fastener rows max.90-inch o.c. (Lim.7)
OPTIONAL Preliminarily
S-M-13 G33, P,L6 INSULATION Secured or OPTIONALAttached in-lap 6-inch o.c.with
Preliminarily Secured HL Fasteners&Plates:JM TPO or -60
under min. secured with top Cover Board JM TPO F8
1-inch E3 layer Fastener rows max. 114-inch o.c. (Lim.7)
JMC13003.13 FL16758-R13 Page 42 of 46
This evaluation report is provided for State of Florida product approval under Rule 61 G20-3. The manufacturer shall notify CREEK Technical Services, LLC of any product changes or
quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other
product attributes that are not specifically addressed herein.
JOHNS MANVILLE CORPORATION
CREEKPVC 8 TPO Single Ply Roofing Systems
14 TECHNICAL SERVICES. LLC, APPENDIX C —APPROVED ASSEMBLIES FOR JM TPO SINGLE-PLY MEMBRANES
APPROVED ASSEMBLIES FOR JM TPO SINGLE-PLY MEMBRANES
The following notes shall be observed when using the assembly tables below.
1. Allowable pressures were calculated using a 2:1 margin of safety per FBC Section 1504.9.
2. Refer to LIMITATIONS and NOMENCLATURE sections of this evaluation when using the table(s)below.
3. Refer to INSTALLATION section of this report for installation detail when the information is not explicitly stated for the selected assembly.
4. The on-center(o.c.)spacing given is the maximum allowable attachment spacing for the rated system.
5. JM Vapor Barrier SA may be installed direct to deck prior to installing the roof assembly components for the following assembly types: C-M-#. C-W-#.
LC-M-#, LC-W-#, LS-M-#, LS-W-#, S-M-#, S-W-#,W-M-#,and W-W-#
6. As Tested information for roof deck construction is provided for information only. The addition of the As Tested deck information does not obviate the
requirement for rational design of the roof deck and roof deck attachment in accordance with FBC requirements.
Assembly System Numbers and Definitions
C-A-t Adhered Assemblies over Concrete Deck New or Existing)
C-AM-# Assemblies with Adhered Membranes over Insulated Concrete Deck New,Existing,or Recover
C-M_& Mechanically Fastened Assemblies over Concrete Deck
C-W-tt Induction Welded Assemblies over Concrete Deck
CW-A-# Adhered Assemblies over Cementitious Wood Fiber Decks New or Existing)
G-A-# Assemblies with All Layers Adhered over Gypsum Deck New or Existing)
G-AM-# Assemblies with Adhered Membranes over Insulated Gypsum Deck New or Existing)
LC-A-# Adhered Lightweight Concrete Assemblies over Concrete Deck New or Existing)
LC-AM-# Li htwei ht Concrete Assemblies with Adhered Membranes over Concrete Deck New or Existing)
LC-M-# Mechanically Fastened Lightweight Concrete Assemblies over Concrete Deck New,Existing,or Recover
LC-W-# Induction Welded Lightweight Concrete Assemblies over Concrete Deck New, Existing,or Recover
LS-A-# Adhered Lightweight Concrete Assemblies over Steel Deck New or Existing)
LS-AM-# I Lightweight Concrete Assemblies with Adhered Membranes over Steel Deck New or Existing)
LS-M-# Mechanically Fastened Lightweight Concrete Assemblies over Steel Deck New,Existing,or Recover
LS-W-# Induction Welded Lightweight Concrete Assemblies over Steel Deck New,Existing,or Recover
R-A-# Adhered Recover Assemblies
R-M-# Mechanically Fastened Recover Assemblies
R-W-# Induction Welded Recover Assemblies
-AM-# Assemblies with Adhered Membranes over Insulated Steel Deck(New,Existing,or Recover
0"4111111111140- 1 Mechanically Fastened Assemblies over Steel Deck New,Existing or Recover
S-W-# Induction Welded Assemblies over Steel Deck
W-M-## Mechanically Fastened Assemblies over Wood Deck New or Existing)
W-W_# I Induction Welded Assemblies over Wood Deck New or Existing)
JMC13003.13 FL16758-R13 Page 1 of 46
This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK Technical Services, LLC of any product changes or
quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty,installation, recommended use,or other
product attributes that are not specifically addressed herein.
CREEK Certificate of Authorization 2gh Dr
17520 Edinburgh
urgh Dr
Tampa, FL 33647
TECHNICAL SERVICES. LLC. (813)4803421
EVALUATION REPORT FLORIDA BUILDING CODE,6T"EDITION(2017)
Manufacturer: JOHNS MANVILLE CORPORATION Issued June 19, 2019
P.O. Box 5108
Denver, CO 80217
(303)978-2478
wwwlm,com
Manufacturing Plants: Scottsboro,AL
Pawtucket, RI
Lancaster,SC
Quality Assurance: UL LLC(QUA9625)
SCOPE
Category: Roofing
Subcategory: Single Ply Roof System
Code Sections: 1504.3.1, 1504.6, 1504.7, 1507.13, 1515.1.1 , 1515.1.4, 1515.2.4, 1523.1.1, 1523.6.2,
1523.6.5.2.9
Properties: Wind Resistance, Physical Properties, Impact Resistance
PRODUCT DESCRIPTION
Products Specification Description
JM PVC-50 mil ASTM D 4434 Nominal 50-mil thick polyvinyl chloride with DuPont Elvaloy
KEE single-ply roof membrane with polyester scrim
reinforcement
JM PVC-60 mil ASTM D 4434 Nominal 60-mil thick polyvinyl chloride with DuPont Elvaloy
KEE single-ply roof membrane with polyester scrim
reinforcement
JM PVC-80 mil ASTM D 4434 Nominal 80-mil thick polyvinyl chloride with DuPont Elvaloy
KEE single-ply roof membrane with polyester scrim
reinforcement _
JM PVC Fleece Backed-50 mil ASTM D 4434 Nominal 50-mil thick polyvinyl chloride with DuPont Elvaloy
KEE single-ply roof membrane with polyester scrim
reinforcement and polyester fleece backing
JM PVC Fleece Backed-60 mil ASTM D 4434 Nominal 60-mil thick polyvinyl chloride with DuPont Elvaloy
KEE single-ply roof membrane with polyester scrim
reinforcement and polyester fleece backing
JM PVC Fleece Backed-80 mil ASTM D 4434 Nominal 80-mil thick polyvinyl chloride with DuPont Elvaloy
KEE single-ply roof membrane with polyester scrim
reinforcement and polyester fleece backing
JM PVC SD Plus-50 mil ASTM D 4434 Nominal 50-mil thick polyvinyl chloride single-ply roof
membrane with polyester scrim reinforcement _
JM PVC SD Plus-60 mil ASTM D 4434 Nominal 60-mil thick polyvinyl chloride single-ply roof
membrane with polyester scrim reinforcement
JM PVC SD Plus-80 mil ASTM D 4434 Nominal 80-mil thick polyvinyl chloride single-ply roof
membrane with polyester scrim reinforcement
JM TPO-45 ASTM D 6878 Nominal 45-mil thick thermoplastic polyolefin,heat-weldable,
TAS 131 single-ply roof membrane with polyester scrim reinforcement
JM TPO-60 ASTM D 6878 Nominal 60-mil thick thermoplastic polyolefin,heat-weldable,
TAS 131 single-ply roof membrane with polyester scrim reinforcement
JM TPO-80 ASTM D 6878 Nominal 80-mil thick thermoplastic polyolefin.heat-weldable,
TAS 131 single-ply roof membrane with polyester scrim reinforcement
JMC13003.13 FL16758-R13 Page 1 of 6
This evaluation report is provided for State of Florida product approval under Rule 611320-3. The manufacturer shall notify CREEK
Technical Services, LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not
specifically addressed herein.
{
CREEK JOHNS MANVILLE CORPORATION
PVC&TPO Single Ply Roofing Systems
TECHNICAL SERVICES, LLC
APPENDIX A - INSTALLATION
INSTALLATION
Note-Refer to the APPROVED ASSEMBLIES section of this report for specific installation details of a selected assembly.
Unless otherwise specified in this report the following installation details shall be met for the named products:
Component Product Installation Detail
#14 fasteners;Min.3/4-inch penetration through the top rib
JM All Purpose Fastener of the steel deck or wood deck; Min. 1-inch penetration into
concrete deck
JM APB Plates 2-inch diameter;Galvalume steel plate with reinforcing ribs
and barbs
JM Extra High Load Fastener #21 fastener;Min. 314-inch penetration through the top rib of
_ the steel deck,
JM Extra High Load Plates 3-inch diameter,Galvalume steel plate with eyehooks
JM High Load Plates 2 3/8-inch diameter;Galvalume steel plate with eyehooks
JM High Load Plus Plates 2 314-inch diameter; Galvalume steel plate with barbs
JM High Load Fastener #15 fastener,Min.3/4-inch penetration through the top rib of
the steel deck or wood deck,
JM High Load LH Fastener #15 fastener with oversized head,Min.3/4-inch penetration
__ through the top rib of the steel deck or wood deck,
JM UltraFast Fastener #12 fastener;Min. 3/4-inch penetration through the top rib of
the steel deck or wood deck
JM UltraFast Plate(Round) 3-inch diameter round,Galvalume steel plate
Fasteners,Battens& JM UltraFast Plate(Square) 3-inch square;Galvalume steel plate
Plates Min. 1.8-inch galvanized steel tube and coated-steel locking
JM Ultra Lok Fastener staple pre-assembled with 2.7-inch diameter Galvalume steel
plate
JM Polymer Membrane Batten Membrane anchors and plastic strips
JM Purlin Fastener Min.3/4-inch penetration through purlin
Min. 3-inch diameter,Induction welded in the field of
JM PVC RhinoPlate membrane,welds not permitted at lap seams;For use only
with bareback membrane
Min. 3-inch diameter;Induction welded in the field of
JM TPO RhinoPlate membrane,welds not permitted at lap seams;For use only
_ with min.60 mil thick bareback membrane
Base sheet fastener with 1.75-inch galvanized steel shank
OMG CR Base Sheet Fastener coated with CR-10 and integrated 2 75-inch diameter
Galvalume plate.
Trufast Deep Well Batten Bar Galvalume steel membrane batten with recessed holes
Trufast Straight Line Batten Bar Galvalume steel membrane batten for use with Twin-Loc Nail
without integrated plate
Trufast Twin Loc-Nail Min. 1.4-inch shank;Base sheet fastener with and without
integrated 2.7-inch diameter plate.
JM MBR Bonding Adhesive Fully adhered at a rate of 1.5-2.0 gal/100 ft2
JM One-Step Foamable Adhesive
ICP Adhesives CR-20
OMG OlyBond 500
JM Two Part Urethane Insulation Adhesive Ribbon adhered in 3/4 to 1-inch wide beads
Insulation Adhesives Canister or JM Two-Part UTA Canister
JM Two Part Urethane Insulation Adhesive
or JM Two-Part UTA
JM Roofing System Urethane Adhesive
JM Urethane Insulation Adhesive Ribbon adhered in 1/2-inch wide beads
ASTM D 312,Type IV asphalt
Fully adhered within the EVT range at a rate of 25-40 lbs/100
Min.0.5-inch, min. 1.8 pcf(HVHZ)or min. 1.5 pcf(non-
Insulation/Cover EPS HVHZ)expanded polystyrene;Adhered boards shall be a
Boards _ maximum 4-ft x 4-ft
Georgia-Pacific DensDeck Min. 1/4-inch thick
JMC13003.13 FL16758-R13 Pae 1 of 5
This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK
Technical Services, LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not
specifically addressed herein.
CREEK PVC JOHNS MANVILLE CORPORATION
&TPO Single Ply Roofing Systems
TECHNICAL SERVICES. LLC APPENDIX A- INSTALLATION
Component Product i Installation Detail
JM ENRGY 3
JM ENRGY 3 C1
JM ENRGY 3 AGF Min 1/2-inch thick,Min. 20 psi; Adhered boards shall be a
JM ENRGY 3 CGF maximum 4 ft x 4 h
JM ENRGY 3 C1 CGF
JM ENRGY 3 FR
JM Fesco Board Min.3/44nch thick;Min.20 psi
JM Fesco Foam Min. 1.5-inch thick;Min.20 psi; Adhered boards shall be a
maximum 4ftx4ft
JM Invinsa Roof Board _
JM Invinsa Foam Roof Board 1/4-inch thick;Adhered boards shall be a maximum 4 ft x 4 ft
Insulation/Cover JM Invinsa FR Roof Board
Boards(Cont'd) JM ProtectoR HD _ 1/2-inch thick;Min.80 psi;Adhered boards shall be a
JM ProtectoR HD FR maximum 4 ft x 4 ft
JM Retro-Fit Board
1/2-inch thick;Adhered boards shall be a maximum 4 ft x 4 it
JM RetroPlus Roof Board
JM SECUROCK Glass-Mat Roof Board
JM SECUROCK Gypsum-Fiber Roof Min. 1/4-inch thick
Board
National Gypsum DEXcell Cement Roof Min.7/164nch thick;Adhered boards shall be a maximum 4
Board ft x 4 ft
National Gypsum DEXcell Glass Mat Roof
Board
Min 1l4-inch thick
National Gypsum DEXcell FA Glass Mat
Roof Board
Base Ply and Vapor ADCO Millennium Hurricane Force Ribbon adhered in 3/4 to 1-inch wide beads
Barrier Adhesives Membrane Adhesive
ASTM D 312,Type IV asphalt Fully adhered within the EVT range at a rate of 2540 lbs/100
ft,For use only with JM PVC Fleece Backed membranes
JM PVC Membrane Adhesive(Low VOC) Fully adhered at rate of 50-90 ft'/gal; Applied simultaneously
to underside of membrane and substrate
PVC Membrane Fully adhered at a rate of 90-130 ft2/gal;Two-side application
Adhesives JM PVC Membrane Adhesive(Water required for bareback TPO;Applied only to substrate when
Based) used with fleeceback TPO
JM Roofing System Urethane Adhesive Ribbon adhered in 1/2 to 3/44nch wide beads
_ JM MBR Bonding Adhesive Fully adhered at a rate of 1.5-2.0 gal/100 W
ASTM D 312,Type IV asphalt Fully adhered within the EVT range at a rate of 2540 lbs/100
ft;For use only with JM TPO FB 150 and 175 membranes
JM Roofing System Urethane Adhesive Ribbon adhered in 3/4 to 1-inch wide beads
JM Membrane Bonding Adhesive(TPO& Fully adhered at rate of 50-90 /gal; Applied simultaneously
EPDM) to underside of membrane and substrate
JM TPO Membrane Adhesive(Low VOC) Fully adhered at rate of 50-90 /gal; Applied simultaneously
TPO Membrane to underside of membrane and substrate
Adhesives JM LVOC Membrane Adhesive(TPO& Fully adhered at rate of 0.55-0.83 gaill 001112 in two-sided
EPDM) application(1.1-1.67 gal/100ft2 total)
JM TPO Water Based Membrane Fully adhered at a rate of 0.6-0.8 gal/1 ;Two-side
Adhesive application required for bareback TPO;Applied only to
substrate when used with fleeceback TPO
JM Two Part Urethane Insulation Adhesive Applied in spatter pattern at a rate of 0.32 gal/100112 or 112-
Canister inch wide beads _
SA Primer JM SA Primer Low VOC Applied at rate of 0.5 gal/sq.
JM DynaBase HW Min.3-inch wide side-laps;Min.6-inch end laps,Torch
adhered to primed concrete deck
Vapor Barriers JM DynaBase Min 3-inch wide side-laps;Min.6-inch end laps;Applied with
hot or cold approved adhesives
JM Vapor Barrier SA Self-adhered to primed wood,gypsum or concrete decks
Min.3-inch sides laps;Min.64nch end laps
JMC13003.13 FL16758-R13 Page 2 of 5
This evaluation report is provided for State of Florida product approval under Rule 61G20-3 The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the duration for which this report is valid
This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not
specifically addressed herein
CREEK JOHNS MANVILLE CORPORATION
PVC 8 TPO Single Ply Roofing Systems
TECHNICAL SERVICES. LLC
COMPLIANCE STATEMENT
The products evaluated herein by Zachary R. Priest, P.E. have demonstrated compliance with the Florida Building
Code, 6"'Edition (2017)as evidenced in the referenced documents submitted by the named manufacturer.
�� PaY R
t111111111111,11,
%%%%
N 2019.06. 19
• SF �s�
No 74021
13:10:53
-04'00'
: 3 STATE OF 44/
'••.• G% Zachary R. Priest, P.E.
SfON q!r� ` Organa ation No.ANE9641on No. 021
CERTIFICATION OF INDEPENDENCE
CREEK Technical Services,LLC does not have, nor will it acquire,a financial interest in any company manufacturing or distributing
products under this evaluation.
CREEK Technical Services LLC is not owned,operated,or controlled by any company manufacturing or distributing products under
this evaluation.
Zachary R Priest, P E does not have, nor will acquire, a financial interest in any company manufacturing or distributing products
under this evaluation
Zachary R Priest, P.E does not have, nor will acquire,a financial interest in any other entity involved in the approval process of the
product.
APPENDICES
1) APPENDIX A—Installation (5 pages)
2) APPENDIX B—Nomenclature(4 pages)
3) APPENDIX C—Approved Assemblies for JM TPO Single-Ply Membranes(46 pages)
4) APPENDIX D—Approved Assemblies for JM PVC Single-Ply Membranes (26 pages)
JMC13003 13 FL16758-Rl3 Page 6 of 6
This evaluation report is provided for State of Florida product approval under Rule 61G20-3. The manufacturer shall notify CREEK
Technical Services,LLC of any product changes or quality assurance changes throughout the duration for which this report is valid.
This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not
specifically addressed herein,
Docu5 ,t;
■ sscu..o
Certificate Of Completion
Envelope Id:5BEC233A788C4CD081E05E1077E7E8B6 Status:Completed
Subject:Please DocuSign:3939 St.Lucie Blvd,Ft.Pierce FSC DSIGNED.pdf
Source Envelope:
Document Pages. 1 Signatures: 1 Envelope Originator:
Certificate Pages:2 Initials:0 Jorge F.Gonzalez
AutoNav:Enabled 10735 SW 216 St
Envelopeld Stamping:Enabled Unit#416
Time Zone:(UTC-08:00)Pacific Time(US&Canada) Miami,FL 33170
jgonzalez@floridatec.net
IP Address 98.211.218.250
Record Tracking
Status:Original Holder:Jorge F Gonzalez Location:DocuSign
12/10/2019 12:48:05 PM jgonzalez@floridatec.net
Signer Events Signature Timestamp
Jorge F.Gonzalez Ej�ENCD20090]45 -L.._ Sent: 12/10/2019 12:48:15 PM
jgonzalez@floridatec.net �°�"7�'�'7 Viewed:12/10/2019 12:48:21 PM
Engineer Signed:12/10/2019 12:48:50 PM
Florida TEC Freeform Signing
Security Level:Email,Account Authentication Signature Adoption:Pre-selected Style
(None) Using IP Address:98.211.218.250
Electronic Record and Signature Disclosure:
Not Offered via DocuSign
In Person Signer Events Signature Timestamp
Editor Delivery Events Status Timestamp
Agent Delivery Events Status Timestamp
Intermediary Delivery Events Status Timestamp
Certified Delivery Events Status Timestamp
Carbon Copy Events Status Timestamp
Elthon COPIED Sent:12/10/2019 12:48:51 PM
elthon@floridatec.net
Security Level:Email,Account Authentication
(None)
Electronic Record and Signature Disclosure:
Not Offered via DocuSign
Michael Sent: 12/10/2019 12:48:51 PM
mwinant@tectaamerica.com CO PI E D J
President
Tecta America Southeast LLC
Security Level:Email,Account Authentication
(None)
Electronic Record and Signature Disclosure:
Not Offered via DocuSign
Witness Events Signature Timestamp
v
12/10/2019 Google Maps
Go gle Maps
1 �
7
r
y
f
le -
�. t
IL
Imagery 02019 Google,Map data @2019,Map data 02019 10 ft
haps://www.google.com/maps/place/Coca-Cola+Bottling+Col@27.4840858,-80.3642066,53a,35y,180.14h.45.07t/data=!3m 1!1 e3!4m6!3m5!1 sOx88def... 1/1