HomeMy WebLinkAboutProduct Approval 1
File Copy .
11.11
n MIAMI-DADE COUNTY
�(J7v PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami,Florida 33175-2474
REVIEWED FOR T(786)315-2590 F(786)315-2599
NOTICE-OF ACCEPTANCE (NOA) CODE CO PI I'AN IE www'miamidade.Qov/economy
Boral Roofing LLC. ST. LUCIE COUNTY
7575 Irvine.Center Drive, Suite 100 BOCCI
Irvine,CA 92618
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section
(In Miami Dade County) and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this
product or material tested for quality assurance purposes.If this product or material fails to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the'use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein,and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: BORAL TileSeal and BORAL MetalSeal HT
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city,state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION-of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,
for sales,advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA# 18-0502.03 and consists of pages 1 through 4.
The submitted documentation was reviewed by Alex Tigera.
Ise
NOA No.: 19-0109.08
MAMIDADF COUNTY Expiration Date: 08/02/23
Approval Date: 02/07/19
Page 1 of 4
r
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub-Category: Underlayment
Material: SBS
PRODUCTS DESCRIPTION:
' Test Product
Product Dimensions Specification Description
BORAL TileSeal 36"x 36' rolls TAS 103 SBS self-adhering asphalt sheet material with a
36"x 72' rolls ASTM D1970 white glass re-enforced polyester surfacing fabric;
for use as an underlayment in sloped roof
assemblies.
BORAL MetalSeal HT 36"x 36' rolls TAS 103 SBS self-adhering asphalt sheet material with a
36"x 72' rolls ASTM D1970 white glass re-enforced polyester surfacing fabric;
for use as an underlayment in sloped roof
assemblies.
Boral Citadel Plus 36"x 72' rolls ASTM D1970 SBS self-adhering asphalt sheet material with a
poly film-facer; for use as a mid-ply underlayment
in sloped roof assemblies.
MANUFACTURIGN LOCATION:
1'. Brentwood,NH.
2. Houston,TX.
EVIDENCE SUBMITTED:
Test Agency Test Identifier Test Name/Report Date
PRI Construction Materials OCF-356-02-04 ASTM D1623 07/25/18
Technologies,LLC. OCF-356-02-02 TAS 103 07/24/18
OCF-356-02-01 ASTM D1970 07/26/18
OCF-424-02-04 ASTM D1623 07/25/18
OCF-424-02-01 ASTM D1970 07/25/18
OCF-424-02-03 TAS 103 07/25/18
Trinity ERD BRLRF-SC16810.11.17 ASTM D 1876 11/28/17
NOA No.: 19-0109.08
Miarn•naoecouNr�r Expiration Date: 08/02/23
Approval Date: 02/07/19
Page 2 of 4
APPROVED ASSEMBLIES:
Deck Type 1: Wood, non-insulated
Deck Description: 15/32" or greater plywood or wood plank
System E(1): Anchor sheet mechanically fastened deck,membrane adhered.
Base Sheet: One or more plies of ASTM D226 Type II or ASTM D2626 with a minimum 4"head lap and a
6"end lap mechanically fastened to deck with approved nails and tin caps 6" o.c. at the laps
and two staggered rows 12" o.c.the field of the roll.
Ply Sheet Apply one layer of Boral Citadel Plus over Base sheet as per current approval.
(Optional):'
Membrane: One or more plies of BORAL TileSeal or BORAL MetalSeal HT Underlayment with a
minimum 3"head lap and minimum 6"end lap.Place the first course of membrane parallel to
the eave,rolling the membrane to obtain maximum contact. Remove the release membrane as
the membrane is applied. Vertical strapping of the roof with BORAL TileSeal or BORAL
MetalSeal HT Underlayment is acceptable. All end laps and laps without black selvage area
shall be sealed under lap using an SBS modified mastic.
Note: When used in Tile roof systems BORAL TileSeal or BORAL MetalSeal HT
Underlayment shall be back nailed to deck with approved annular ring shank nails and tin caps
at a maximum 12"o.c. at the side laps. No nails or tin caps shall be exposed.
Surfacing: Approved for Adhered Roof Tile using TILE BOND or AH-160,Mechanically Fastened Roof
Tile,Metal Roofing, Wood Shake&Shingles, and Asphaltic Shingle assemblies.
NOA No.: 19-0109.08
MIAMI•DADECOUNTY Expiration Date: 08/02/23
Approval Date: 02/07/19
Page 3 of 4
'i
LIMITATIONS:
1. Fire classification is not part of this acceptance.
2. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code.BORAL TileSeal and BORAL MetalSeal HT underlayment shall be installed in strict
compliance with applicable Building Code.
3. BORAL TileSeal and BORAL MetalSeal HT underlayment shall be applied to a smooth, clean and dry surface
with deck free of irregularities.
4. BORAL TileSeal and BORAL MetalSeal HT underlayment shall not be applied over an existing roof membrane as
a recover,but may be applied over a roofing Base/Anchor sheet underlayment.
5. BORAL TileSeal and BORAL MetalSeal HT underlayment shall not be left exposed as a temporary roof for longer
than 180 days of application.
6. The standard maximum roof pitch for BORAL TileSeal and BORAL MetalSeal HT underlayment shall be 6:12
when tiles are loaded directly to the BORAL TileSeal or BORAL MetalSeal HT underlayment; loading boards or
battens are required on roof pitches greater than 6:12".
7. Refer to Prepared Roofing system Product Control Notice of Acceptance for listed approval of this product with
specific prepared roofing products.
8. Tiles shall be stored on battens on roof pitches greater than 6:12".
9. BORAL TileSeal and BORAL MetalSeal HT underlayment may be used with any approved roof covering Notice
of Acceptance listing BORAL TileSeal or BORAL MetalSeal HT underlayment as a component part of an
assembly in the Notice of Acceptance. If BORAL TileSeal or BORAL MetalSeal HT underlayment is not listed, a
request may be made to the Authority Having Jurisdiction(AHJ)or the Miami-Dade County Product Control
Department for approval provided that appropriate documentation is provided to detail compatibility of the
products,wind uplift resistance, and fire testing results.
10. All nails in the deck shall be carefully checked for protruding heads. Re-fasten any loose decking panels. Sweep
the deck thoroughly to remove any dust and debris prior to application.
11. When applying the membrane in the valley, start at the low point and work to the high point,rolling the membrane
from the center outward in both directions. For ridge applications, center the membrane and roll from the center
outward in both directions.
12. Roll or broom the entire membrane surface so as to have 100% contact with the surface,giving special attention to
overlap areas.
13. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance and applicable Building Code.
14. All protrusions or drains shall be initially taped with a 6" piece of underlayment. This target piece shall be pressed
in place and formed around the protrusion to ensure a tight fit. A second layer of BORAL TileSeal or BORAL
MetalSeal HT underlayment shall be applied over the underlayment, and sealed using an SBS modified mastic.
15. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
16. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo, city
and state of manufacturing facility, and the following statement: "Miami-Dade County Product Control Approved"
or the Miami-Dade County Product Control Seal as shown below
MIAMI•DADE COUNTY
�Ljumvjvj
END OF THIS ACCEPTANCE
MIAMI•DADE COUNTY
NOA No.: 19-0109.08
• , Expiration Date: 08/02/23
Approval Date: 02/07/19
Page 4 of 4
MPaMI''Ct4DE
]PRODUCT CONTROL SECTION
DEPAIrrMENT'OF REGULATORY'AND ECONOMIC RESOURCES(RER) 11805 SW 26 Strect,Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami,Florida 33175-2474
T(786)31 S-2590.F(786)315.2599
NOTICE OF ACCEPTANCE(NOA) wiv w:miamidnde.eov/cennomv
TarcolSpecialty Products,Inc.
One Information Way,Suite 225
Little.Rock,AR 72202
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the'use of construction materials.The
documentation,subinitted has been reviewedand accepted by Miami-Dade County:RER-Product Control;Section,wbe
used in Miami Dade County and other.areas where allowed by the Authority Having Jurisdiction,(AHJ).
This NOA'shall not be valid 1.aftef the expiration date stated below.The Miatni-Dade County"Product:Control Section
(in Miami-Dade County)and/or the AHJ(in areas other than Miami-Dade County)'reserve the right to have this
product or material tested forquality,assurance purposes.If this product or material to perform in the accepted
manneri the manufacturer will incur the expense of such testing and the AHJ nay immediately"revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves.the right to revoke this acceptance,
if it,is:determined by Miami-Dade County Product Control Section that this'product or material fails to meet the
requirements of the.applicable building code.
This product is approved as described herein_,and has been designed'to comply with the Florida Building Code.
including the High-Velocity Hurricane Zone of the Florida,Building Code:
DESCRIPTION:,Tarco Rooting Membranes and Underlayments
LABELING:Each uiiif shall'bear a permanent label with the manufacturer's name'onlogo;city,`state and"following
statement."Miami-Dade County Product Control Approved",unless othenvise'noted herein.
RENEWAL of this'NOA shall be considered after a renewal application has been f led.and therehas-been no change
in the applicable building code negatively affecting the.performance of this'product.
TERMINATION of this NOA will occur after the expiration date or if there has,been a revision.or change in the
materials,use,and/or manufacture of the product or process:Misitse of this NOA as'an endorsement of any product,
,for sales,'advertising or:any other purposes,shall automatically terminate this NOA.;FaitIure to comply with any section
of this NOA shall be cause,for termination and removal.ofNOA.
ADVERTISEMENT:'The NOA number preceded by the words,Miam-Dade-County,Florida, and'followed
by the expiration date iliay be displayed,in advertising literature. If any portion of the NOA is displayed„then
it shall be done in iis.entirety.,
INSPECTION:A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall b.Ovailable;for'inspection at the.job site at the request of the Building Official.
This NOA renews NOA No. 12-0420.02 and consists of pages 1 through 15.
The subinitted documentatiomwas reviewed by Alex Tigera
-N.OA No:16-1116.09
MIAMI•DADE COUNTY
� Expiration Date: 01/25/22
Approval Date: 01/12/17
Page 1 of 15'
ROOFING COMPONENT APPROVAL
,Category:, Roofing
Sub-Cate2ory: Underlayment
Material: Asphalt,SBS,,Polyester
SCOPE:
This acceptance is for Tarco Roofing Membrane and Underlayments,for use with approved-prepared roof
assemblies where-the applicable-TAS/ASTM specific underlayment-is_specifled and installed with prescribed approved
adhesives,fasteners and fastener densities,,as described in this Notice of Acceptance;dcsignedto;comply with the
Florida-Building Code;including the High Velocity Hurricane Zone of the Florida'Building Code.,
TRADE NAMES OF'PRODUCTS MANUFACTURED OR-LABELED BY•APPLICANT:•
Product• Dimensions Test Specification Product Description
30#ASTM 3'x,72"rolls ASTM 6226,Type h Asphalt saturated felt underlayment
Specification Felt
Manufacturing
Location#1&c#2
EnsyLay 3'•x 133 4"rolls ASTM D226 Type"li Shect material comprising a polyester•
Manufacturing ;substratei,coated,with bituminous coating for
Location#2 use.as an underlayment in roofing
applications. Designed as a shingle and,metal
roofiiig.uiiderlaynient:and„for use-in tile,
roofing assemblies whenAised.with.an
approved TAS 103 the underlayment cap
sheet.
.Fiberglass Mineral '3'x 36'rolls ASTM 63909 Mineral surfaced glass,fiber,reinforced',
Surfaced Roll asphalt coated roll roofing for hot mop or cold
Roofing process application.
Manufacturing
Lmatiou:#1
ASTMOrganic Tile• 3'x 36'rolls ASTM D6380 Asphalt;saturated granular surfaced felt
Underlayment Type.II underlayment,for hot mop application.
Man[factoring
Location#1
EasyMop SBS 3.'x 36'rolls, TAS 104 Granular-surfaced polyester reinforced,SBS
dfanuiactu ing modified bituminous membran6;for hot:mop or
Location#1 cold process application.Designed as a tile.
roofing imderlayment.,
NOA No.:16-1116.09
MIAMMADE COUNTY Expiration Date: 01/25/22
FH 8 1
Approval Date: 01/12/17
Page 2 of 15-
Fast96 3'x 36'rolls TAS 103, Granular surfaced,asphalt-impregnated
Mrintifacturing ASTM,D249 organic feltxeinforced,bituminous sheet:
Location#1 ASTM D6380 material with aself=adhdsrve6ottorn,laycr,,,for
use'as an underlayment in sloped roof
assemblies. Designed as a tite roofing.
underlayment.
PS200Hr- 3'x 66'8"roils. TAS f 03 Fabric surfaced,fiberglass reinforced,SBS
Manufacturing self-adhesive
D1970 modified bituminous shcet•material with a
Location#1 self-adhesive bottom layer,for use_as an
underlayment in.sloped roof assemblies.
Design edas'a'suingl"e,-tile and metal roofing;
underlayment.
,,P,S200'1Q 3'x 66'8"rolls ASTM D1970 Film surfaced,fiberglass reinforced;SBS
mu fgcturing modified bituminous,sheet material w th:a
M
Location"I ' self adhesive bottom layer,for use as air.
underlayment in slopcd'roof assemblies,.
Designed as a metal•and shinglex6ofipg
underlayment.
MS300 3'x 66T',r6lls ASTM D1970 Fine granular surfaced;fiberglass reinforced,
Aianefocturing 3'x 33'4"'rolls bituminous sheet maierial with a self-adhesive
Location#1 bottom layer,for use as an underlayment,in
sloped roof assemblies. Designed as an ice
and water shield,and a s}iingle roofing
underlayment.
9S460 5'x 66'8"rolls' ASTM.Di97ll Smootlrsurfaeed,.fiberglass"reinforced,
lliamrfacnu'ing V'x 33'4"rolls bituminous sheet materiat with a self-adhesive
Coronae#1 ng bottom layer,for use as,an underlayment in,
sloped roof assemblies. Designed as an ice
and water"shield,and a shingle and metal
roofing,underlayment.,
NR5OOnT 3'x 66'8"rolls ASTM D1970 Film surfaced,non-reinforced,bituminous
Mom factirring sheet material with a self.-adhesive bottom
Location#3 .layer,for,use as antindeilaymell in sloped
roof assemblies:Designed as an ice and water,
shield,and a shingle and metal roofing
underlayment.
NOA No::,16-1116.69.
MIAM VAOEeouNTY E>plration bate: 01/25/22
. r
Approval Date: b1112117
Page'3 of 15
MANUFACTURING LOCATION:
1. Greencastle,PA
2. Belton,TX:
3. Coshocton;OH
EVIDENCE SUBMITTED:
Test Aaency Test Identifier Test Name/Renort Date
Atlantic'&-CarribeanRoof ACRC06-0.13 TAS 163 06/14/06
Consulting,LLC
TRI.Asphalf Technologies TOT,-003-02-01. ASTM D220 T' ype fI 08/22/02
TOV029-02-01 'TAS.110,ASTM D249&D 6380 01/05/05
TOT-030-02-01 'TAS 110,ASTM D249&D 6380 07/05/05
TOT-04 11 02-0 1 'TAS-110,ASTM D226 Type II 05/24/06
TOT-042-02-01 ASTM D4798&ASTM G155, 05%22/07
Trinity1:E111) T3580.10.06-2 TAS:103 10/26/06
T3580.40.06 TAS"103,ASTM D6380 .10/12/06
T30160.08.09-R1 ASTM'D 1970 '10/12/10
T10550.07.08 ASTM D4798,&ASTM D1970• 07/30/08
T32530.08.10. -ASTMD.1970 08/17/10
T33190.08:1.0 TAS403 08/06/10,
T43930.09.13-R2 TAS 104 09/11/13
T40790.04.12 ASTM D6380 04/06/12
T40780.04.12 ASTM D3909 04/06/12'
T37610.07.11 TAS 114-1) 07/29/11
IRT-Accon IRT07-0606 ASTM.D 1970 07/11/07
IRT 07-0036 ASTM`D 1970 02/22/08
1RT08-0002 ASTM D1970 02R2/08
NOA No.:.16-1116.09
M AWDADECOUNTY Expiration Date: 01/25/22
,Approval DateC 01/12/17
Page 4 of 15
APPROVED ASSEMBLIES-309 ASTM SPECIFICATION FELT:
Deck Type: See Installation Requirements and General Limitations.below.
DeckDescription: Sce'Installation-Requirements and General Limitations below.
System E(1): Sce Installation Requirements and General Limitations below,
INSTALLATION REQUIREMENTS=30#•ASTM SPECIFICATION FELT:
1. 304 ASTM Specification Felt shall be installed in strict.compliance with applicable Buildin&Codes.
2.. Observe and comply with roofing practices and guidelines as outlined.by the National Roofing Contfactois
Associations(NRCA)when installing 30#Felt.
31. During installation of 30#Felt,comply with Occupational Safety and Health Administration(OSHA)safety.
standards;•use.common sense measures and adequate safety precautions to prevent accidents.
4. 3,09 ASTM Specification Felt shall be installed with a minimum 4"end lap in a shingle layer fashion and
fastened as required by,appUcable system assemblies NOA or FBC 1518.2.
GENERAL-LIMITATIONS--30#ASTM SPECIFICATION FELT:
I, Fire classification,is,not part of this acceptance;refer'to a"current Approved Roofing"Materials birectory for fire
ratings of this product..
2: This acceptance is'for'prepared roofing applications. Minimum ddek redi irements shall be in compliance"with:
applicable building code.
3. 30#ASTM Specification Felt may be used"with any approved roof covering Notice of Acceptance listing
ASTM-D226 Type II felt as a component part of an assembly in the Notice of Acceptance.
4. All products lised herein.shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code,
NOA No.:164116.09
MIAMMADECOUNTY Expiration Date: 01125/22
Approval Date: 01712/17
Page 5 of 15
ti APPROVED ASSEMBLIES-EA$YLAY:
Deck'Type 1: Wood,Non-insulated
Deck Description: 1'hi"or greater plywood or wood plank
System E(2): Anchor sheet mechanically fastened to deck.
AnchorShect: One of more plies of,i3asyLay underlayment,with a minimum 4"wide sidelap and a minimum
'8' wide end.lap,mechanically fastetied'to deck.
Fastening:' Approved nails and,tin caps,6"o.c.within lap and.two equally spaced staggered rows 12"o.c.
in'the field(for Anchor/Base sheet)..
Surfacing: Approved Roof Assemblies in lieu of FBQ perscribed ASTN1 D 226 Type II felt
INSTALLATION REQUIREIMENTS-EASYLAY:
1. EasyLay shall.be installed in strict compliance with applicable Building'Codes.
2. Observe and comply•with roofing practices and guidelines as outlined by the National Roofing Contractors
Associations(NRCA)when installing EasyLay.
3. During installation,comply with Occupational Safety and Health Administration(OSHA)safety standards;use
common sense measures and adequate safety" precautions to prevent accidents.
4. EasyLay.shall be acceptable fof use with asphaltic shingles,mood shakes'and shingles;quarry slate,the and
metal roofing assemblies.
5. Re-fasten,any loose decking panels,and check for protruding'nail heads;prior to the application of EasyLay.
6.1 Place a full,width piece of EasyLay,parallel to the eave(low)edge of the roof.'
7. Unroll EasyLay 2 to 3 feet,with the lay lines facing up,and position the end of it to the edge-of the cave and.
rake.
8. Install a few,fasteners at the top,near the rake,and roll out the sheet to a manageable length.
9. Pull,straighten and align the sheet so that any wrinkles-are eliminated and the sheet is even with the cave edge.
lo. EasyLay shall be fastened with approved roofing nails and tin caps or approved cap nails,driven by,hand or
pneumatically;spaced 6"o.c.at all laps in the center of the-seam area,and.two staggered rows fastened IT'
o.c.in the field of the sheet.
11. When installing nails,apply so that the head of the nail is flush with'fhe EasyLay surface,without cutting into
the EasyLay surface.
12. Fastening shall be done from the top to avoid walking of kneeling on unsecured sheet.
13. Continue on tithe end of the substrate and fasten down.
14. Align the next Poll over the preceding sheet so as to,form a'minimum 4"overlap:
15. -Then install the just placed sheet,per instructions above.
16. The bottom of the second course of EasyLay shall lay on top of the first course so,that any water will flow over
the top of EasyLay.
17. Apply subsequent sheets.in the same manner,with 4"side laps and 6"'end laps over the preceding sheets.
18, When'the top course is reached,lap about 6"of EasyLay over the ridge.
NOA No.:16-1116.09
WMIAMMADECOUNW Expiration Date: 01/25/22
Approval Date: 01/12/17
Page 6 of 15
19., ,Install EasyLay a iniiumum,of 61'up,any vertical surfaces.
20:. Stagger the.end laps a;tninimum of IP,from:the preceding course;
21.. Afterinstalling,EasyLay on the field of the roof,instal l drip edge at`the eaves.6fused).
M �When..applying•EusyLay'in the valley,start of the low point and work to the:high point,rolling,thd membrane_
from the,center,outwird in each direction. Make sure`there are no rips,or.large wrinkles.in:the'Easy4y.
23. Before applying horizontal section&ofEasyLay,install a vertical length;of EasyLay down the center of the
valley.
24, Several.sections;of EasyLay can be';used;but be certain to overlap the'higher sectionsseveral inches so any
water will flow over the top of the sheet.
25. 'EasyLay underlaymerit in the valley.areas-must be covered-whit code presci-ibcd metal or other•approved valley
lining material.
20. Apply a muumum4/16"Cluck uniform layer of SBS trowel grade modified flashing ceineut to'water'proof
,areas-of EasyLay where any cuts.or tears have occurred.Seams or joints;mayrequirethe application of an.SBS
trowel grade,tnodified flashing cement.
2T, Flash vent pipes,stacks,chimneys and penetrations in:comphance with Roof Assembly current
Product_ControI'Notice.of Acceptance and,applicable,Building Code.
GENERAL LIMITATIONS EASYLAY:
1. 'Fire;classification is not part of this,acceptance;ieferto a current Approved Roofing Materials,Directory" for fire,
ratings of this product.
2'. 'This acceptance is for prepared roofing applications. Minimum,deck_reyuiicttents,shall be in corripliance,with
applicable building,code,
3.- EasyLay shall be applied to a clean,and-dry surface.
4•, Easy shall not.'be torched or hot'mopped to. Refer to manufacturer's published aiterature foraddifional
bformation.
6. EasyLay shall not be used on slopes less,than 2:12,unless the slope is acceptable to the weather resistant
covering.' In general,on'slopes'less than 4:12,.a doublMayer of EasyLay is°recommended1.
Double layer application is-best achieved by using 19"side laps,makitig_sure theside laps are`shingled nY to
'shed water.
;6. When installing,EasyLay,the;roofsystem must include proper ventilation.,
7: Refer to prepared roofing systeni.Product Control Notice of Acceptance'forlisted approval ofEasyLay with
specific prepared�roofing products:,EasyLay may be used with any approved roof covering Notice of
Acceptance listing ASTM D 226 Type II felt as a component part of an assembly irk the Notice of Aecepianee.
8; All products,listed.herein shall have_a quality assurance,audif in accordance with the FloridaBuilding Co&and
Rule 61G20-3,of the Florida Adininistritive'Code.,
% ;EasyLay shall not be left exposed:for.longer than 30 days after application:
10. Tlie manufacturer reserves the right to change',p"roduet'exposure period at-any time;not to-exceed the preceding
maximum time:,lirnitations.
NOA No 16-111.6.09'
ttuiMH)AD Courr'rY Expiration Date: 01125122,
F.-M neM
Approval Date: 01/12/17
Page'7 of 15
APPROVED ASSEMBLIES-FIBERGLASS-MINERAL SURFACED ROLL ROOFING:
Deck Type: See,Installation.Requirements and General Limitations below.
Deck Description: See Installation Requirements and General.Limitations below,
Systein,E(3): See Installation Requircments and General Limitations below..
INSTALLATION,REQUIRENIENTS-FIBERGLASS MINERAL SURFACED ROLL ROOFING:
1'. Fiberglass Mineral.Surfaced Roll Roofing may be used with any approved roof covering Notice of Acceptance
listing Fiberglass Mineral Surfaced Roll Roofing as a component part-of an assemblyin.the Notice of
Acceptance or wherever a,ASTM D3909 roof membrane,is specified and.installed.With prescribed approved
asphalt,adhesives.,'fasteners and fastener densities per applicable FBC requirements.
2. =Observe and comply with•roofing piactices;and guidelines as outlined by the National Roofing Contractors
,Associations(NRCA)when installing Fiberglass Mineral Surfaced Roll Roofing.
3. During installation of Fiberglass Mineral Surfaced Ro11.Roofidgi comply with Occupational Safety and Health
Administration(OSHA);safety standards;use common sense ineasures"and adequate safety precautions to
prevent accidents..
GENERAL LIMITATIONS—FIBERGLASS MINERAL SURFACED ROLE ROOFING
I. Fire classification is not part of this acceptance;refer to,a current.Approved Roofing Materials Directory for fire.
"ratings of ihis product,
2. This acceptance is,for,prepared roofing applications:;Minimum deck requirements shall becin compliance with
applicable building codes.
3. All products lisad herein shall have a quality assurance audit in accordance,with the Florida'Building Code and
:Rule 61 G20-3 of the Florida Administrative Code.
N AMPOADECOUNTY NOA No.:16-1116.09
,Expiration Date: 0112SI22
Approval Date: 01/12/17
Page S of 15
APPROVED-ASSEMBLIES ASTM ORGANIC TILE,UNDERLAYMENT
Deck Type: See-Installation Requirerents and General'Limitations below:
Deck Description; See,Install'afion:Requirefncnts and Generat'Limitations below:.
System E(4): See Installation Requirements and General Limitations below;
INSTALLATIOKREQUimmiEwS ..ASTM.ORGANIC-TILE U-NDERLAYIVIENT:
I ASTM Organic TileAUnderlaymeni may.be used with'any approved,roof covering Noticesof Acceptance listing
sASTM;Organic Tile Underlayment asa oomponent•partof an assembly iri-thc"Notice of Acceptance or wherever
a ASTM Db380 roof membrane-is specified"and installedIwith prescribed;approved asphalt,adhesives,
and fastenei•densities per applicable`FBC requirements.
2. Observe'and comply with roofing practices and guidelines as outli.ned'by,the National'Roofing.Contractors
Associations(NRCA)ivlten,installitig ASTM Organic"Tile'Underlayment..
3. ''During installationvf ASTM Organic Tile Underlayment;comply with Occupational Safety and Health
Administration(OSHA):safety standards;use'commonsense measure"sand adequate safety precautions to.
prevent accidents,.,
•v
GENERAL LTVII uolsls—ASTM OR6AIV7C TILE'LINDERLAYMENT:
1. Fire classification;is not,part•of this acceptance;refer to a'current,Approved,Roofing 1 fdtertalsvDireefory'for fire.
ratings of this product.
2. This acceptance is forprepared roofing applicaiions;,Minimum_,deck tequiremenis shall be iti cotupliance with.
:applicable building codes.
3. All products lised bercin shalt have.a quality assurance audit in accoidance.with the.Florida,Building_ Code and
Rule 61 G20=3.of the;Plorida_Administrative Code.
a Mwrttanoecurarr- NOA,No 1611"MOO
Ezplratlon Date 01/25/22
Approval Datc: 01/12h7
Page'9:of 15
.APPROVED•ASSEMBLIES—EAsyMoP;SBS:
beck'Type`l: Wood,Non-Insulated.
Deck`Description:. Minimum 19/32"plywood,wood plank
System E(5): Anchor sheet mechanically fastened to deck,membrane;adhered with Hot asphalt or
Approved.adhesive..
-Arichor/Base Sheet: One or more plies of ASTM 13226 Type 1I or ASTM D2626 with a minimum 4"wide side;
lap and'a minimum 9"wid'e end lap;mechanically fastened,to deck.,
1asfening: Approved nails and tin caps 6"o.c.within lap and.two equally spaced staggered rows IT'
o.c,in the field(for Anchor/Base sheet only):
,Membrane; EasyMop SBS applie&to Anchor/Base Sheet with hot asphalt or with approved:adhesive as
specified.in RAS;Ill 8,119 or IX
(See#13 in Installation Requirements for back nailing)
Surfacing: Approved Roof Assemblies as specified below.
INSTALLATION REQUIREMENTS—EASYMOP SBS:
1. Tareo EasyMop SBS shall be4tistalled in'strict compliance with applicable Building.Codes.
2. Observe and comply with,roofi'ng practices and guidelines as outlined by the National Roofing Contractofs
Associations(NRCA)when•instaliing EasyMop SBS.
3. During installation,comply with Occupational Safety and Health Administration(OSHA)safety.staridards;use
common sense,measures and adequate,safety precautions to prevent aceidcnts.
4. EasyMop SBS shall'be an acceptable underlayment for mechanically fastened roof tile and-adhered roof tile.
Applications,
5. Re-fasten any loose decking panels;and check for protruding nail heads:prior to the application of EasyMop
SBS.
6. EasyMop SBS shall not be adhered:directiy over any pre-existing roof membrane.
7. All approved substrates are to be,clean,'dry and free of any loose debris or moisture prior to the.applicaaon of
the EasyMop;SBS. Refer to applicable building.codes prior to installation to verify acceptable substrates.
8.. Prime,alII metal collars,flashing,valleys;,liner,drip edge and concre'te.deck substrate with ASTM-D 41 primer.
9. Applicator may cut.EasyMop SBS into sections for workability and allow to relax prior to application.
10. Place EasyMop.SBS-over metal drip edge in,accordance with RAS 141.
1.1. Install the first course of EasyMbp.SBS parallel to the'eave edge.
12. It is recommended that end laps be:staggered a minimum of.1 V from the preceding""course.
.
13. EasyMop SBS shall be back nailed along the head lap.",
he nails shall be;1 i gauge V 4"approved ring shank
type;gpplicd witlra minimum of;a.flh'-approved tin.cap.or.approved"capnailas requiredper the High Velocity
Hurricane Zone.(IIYI secnon;of,the FBC,at a minimum rate of"12"'o.c. The head.la_p of the preceding
layer-of underlayment is.to cover the area being baek,nailed'.
14. Flash vent pipes;stacks,chimneys andpenetrations in compliance with Roof Assembly.-current Product,
Control Notice.of Acceptance_Arid applicable Building'Code.
T5. Vertical sti-apping of EasyMop SBS membranes is acceptable.
hDnoEcouwTY NOA No.:16-1116.09`
MIAM
Expiration Date:,01/25/22'
Approval Dater 01/1VI`7
Psigejo,of 15.
GENERAL LIMITATIONS=EASYMOP SBS:
1. Fire classification is not part of this acceptance;refer to a current ApprovedRoofng Materials,Directory,for fire
;ratings of this product.
2. This acceptance is for prepared roofing applications..Minimumdeck requirements shall be incompliance with
applicable building code.
3. Tarco EasyMop SBS shall not be installed when any fonts of moisture'such as water,dew,rain,etc.is present
on the substrate.
4. Tarco EasyMop SBS are to be applied'to a smooth,clean and dry surface,with the deck free,from irregularities.
5. Ensure roof has positive drainage prior to installation of Tarco EasyMop SBS.
6. Tarco EasyMop SBS shall not be applied over a pre-existing roof membrane or system.
7. Care should be taken during the loading procedure.to keep foot traffic to a minimum and avoid dropping the
roof covering directly on the underlayment.
8. All tiles shall.be staged(two tiles perpendicularto slope,four tiles on top parallel to slope)as per
manufacturer's requirements,not to exceed 6-high,to the standard maximum roof pitch of 5:12 for flat tiles
and 6:12 for lugged tiles(See Tile Staging Method diagram.below).
At roof slopes greater;than the above l mitadons,'the use of,loading battens or toe boards are required to load the
roof tile.
Tile Staging Method
Z
a
�V\.�� .� .,. t `�✓� .��.� rya.
.b +1
`F
- i 3
Front View-Staged Tiles(Slope Side View-Staged Tiles(Slope 1)
9. The manufacturer reserves the right to change the the staging method at any as well as the number of tiles
stacked, not to exceed the precedingaitaximum number of tiles limitation.
10. Tarco EasyMop SBS shall not be left exposed as a temporary roof for longer than 180 days after application.
The manufacturer reserves the right to change product exposure period at any time;not to exceed the preceding
maximum time limitations.
11. Refer to prepared roofing system Product Control Notice of Acccptance;for.listed approval of Tarco
underlayments with specific prepared roofing products. Tarco EasyMop SBS may be used with any approved
roof coverings Notice of Acceptance-listing Tarco EasyMop SBS or TAS.104 standard as a'component part of
an assembly in,the Notice of Acceptance.
If Tarco EasyMop SBS or the TAS.104.stand5rds are:not listed,arequest„may be,made to the Authority Having
Jurisdiction(AHJ)or the Miami-Dade County Product,Control Department for approval provided that
appropriate documentation is provided to detail compatibility of the product,wind uplift resistance,and fire
testing results.
112. All products lised herein shall have a"quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
NOA 14o.:16-1116.00
MAWDADEeourrrr Expiration Date: 01/25/22
' Approval Date: 01/12/17
page 11 of 15
APPROVED ASSEMBLIES—TARCO,SELF-ADHERED"UNDERLAYMENTS
i
t Deck Type 1:; Wood,Non-lnsulated
Deck Description: Minimum.l9/32"plywood,wood,plank
System E(6): Anchor sheet mechanically fastened to deck,membrane adhered.
Anchor/Base Sheet: One or more plies of ASTM D226 Type II,ASTM D2626,or EasyLay.undcrlayment,with
a minimum 4"wide side lap and a minimum 8"%vide,end lap,mechanically fastened io
deck.
Fastening: Approved nails and tin caps 6"o.e.,within lap and two equally spaced staggered rows 12"
o.c,in the field(for,Anchor/Base?sheet'only).
Membrane: All Tarco self-adhered membranes applied to approved-Anchor/Base Sheet.
(Sec#.1'5 in Installation'Requiremetits for back.nailing)
Surfacing: Approved Roof Assemblies as specified below.
Deck Type 3: Concrete,Non-Insulated.
Deck,Description: Structural concrete or concrete plank min.2500 psi
System F(1): Membrane self-adhered to concrete deck.
Deck Preparation: The concrete deck shall be clean and dry and.cured for a minimum of 28 days
Anchor/Base Sheet: None.
,Fastening: Membrane shall be back nailed with approved concrete fasteners and.15/8"approved tin
caps at_a,maximum spacing of 9"o.c:at the head laps,and be covered by the preceding
layer.M..back nail fasteners or tin caps shall remain exposed).
Membrane' Tarco PS200HT"self adhered membrane applied directly to concrete deck.
(See Fastening above for back nailing)
Surfacing: Approved Roof Assemblies as specified below.
NOA No.s 16-1116.09
MIAMI4DADECOUNTY Expiration Date: 01/25/22
Approval Date: 01/12/17
Page,12 of 15
INSTALLATION REQUIREMENTS,--TARCO SELF-ADHERED UNQE,RLAVMENT$:
1. Tafco.self adhering underlaymentsAiall be installed in strict compliance with applicable Building Codes,
2. Observe and comply withroofing practices and ituidqlincs as outlined by the-National Roofing Contractors
Associations(NRCA)'*lien installing T&cS self adhering underlaymenis:
3. During,installation,-coMply,.vith.'OccupationaI Safety and Health Administration(OSHA)safety standards use
common.sense',mcasures and adequate safety,precautions to prevent accidents.
4. Fast90 and PS2004T shall'be acceptable underlayments for mechanically fastened rcioflile.a,rid adhered roof tile
applications. ,M8300,atfd'SS400sl.ial I be-hc6eotable,underlaynientg,for asphaltic shingles,-wood shakes and.
shingles,and,slAte or simulated slate.roof assemblies. PS200"u and NR5001T-shall be acceptable
underlayments for asphaltic shinglesi wood shakes.shingles,:and metal roof panel assemblies.
5. Re-fasten,ariv loose decking panels,1addche&for,protfuding,nail headsp'rioi'to the application of the Tarco
self adhering underlayinents.
6t Tiirco,,self'adhering,underlayments sliall not be adhered directly over ahy,pie-existing roof membrane..
7. All:approvedsubstrates are to be.elean.,dry r litAicatfon of and free of loose debris or moisture prio to-die a
the.,Tarco self adhering underlayments. Refer app,lic#16 building codes,prior to installation to verify
acceptable-substrates.
9. Prime-all metal collars,flaslimg,Valleys,liner;drip edge and coricreteAecksubstrate,with ASTMD,41 primer,
water based acrylic oruwater based,polyffier modified'primer:
9. 6turactor may-cutthe underlayments' ,jp ed�etnacco o'npgections forrworkability aq4AIlqw to,relax,prjqr-.to.application,
-10. Plac.6the,unddilaym&iitsdveriiieial-dri" ' 'd, ance With RAS111.
11, install the first'coutsd of underlayi-fient pqrallel,to the gave"edge.
12, Apply the underlayment,working front the centerofthe material continuously.to the ends,of the°shleet(half.of
the length of the sheet.is the center);taking care to avoid wrinkles and ridges.
13. Remove the underlayments release film rapidly in"a continuous fashion. Ensure the bottom adhesive side of
the membrane does not adhere to its self. In the event'this transpires,separate the two layers immediately.
After some time i impossible to do,so,widioutdamaging the material.
Kmgybecomei.
14.. It is recommended that end laps be staggered a minimum,of 18",from the preceding course.
5'. Undeflaynients'ake to 0a,c-k naAcd alongthchead faij,The nail§'Shall,ho,i-l- approved,ring shank
gapgc'11�47`
type ap_plied with.a minimum of aV/a"approved.tin cup or approved caphail'as,required,per.thd High Velocity Hurricanelone,(HVHZ)section of the FBC,at a:miiiimum rate of 9"o'x. The head lap of the preceding layer
of underlayment. is to cover the area being back.nailed.
16., Roll orbroorn the entire membrane surface paying special attention to aLt,"overlap areas"side'laps,endlapsj—
joints"to ensure adhesion with acceptable substrates. A minimum of.a-28 lb weighted,roller-m4y,be used1or
'steep sl6pe4ppli'catiotis. The use ofa'soft bristled push bi-60in is acceptable on steeper'sliap The above.
mentioned procedures are ncc6ssaryJn order to apply uniform pressure and,alloW.fbr contact-of the
'membranes.
17. Apoly'18'?thick uniform layer of S)3S trowel grade modified bitumefi asphalt zidlibsiVe/-flashing cement
throughout the contact area of the.6"granule over granule and fabric over1fabric end laps. Once the
aforementioned procedure has bderi completed the membrane must thcn,bc hand rolled''Jn-place in order to
i ensure,contact.oftnembrane and achieve a minimum of IMP"aspha'it i6'bledd out in designated area
18. Tarro self adhering underlayments Alill'be applied to,protrusions,,slope changes,valleys,curbs,and other roof
top penetrations before any othersections of thd root,
.19. "When applying underlayments in the valley,start at the low point and work to,the high-poini,roiling the
membrane from the center outward in each direction.
NOA Nb.;16-1116.09
MrM'1AM1-DADE COUNTYM Expiration'Rate, 01/15/22'
Approval Date;-Of/12/1.7
Page 13 6f,15
20: For ridge applications,center theV iddithyinent and roll'from the center-6 in otli directions:_
21. Flash vent pipes,stacks,chimneys and pepetrations in compliance with Roof Assembly current Product
Control Notice of Acceptance and applicable Building Code.
22. All protrusions or drains shall be initially taped with a 6"piece of like kind membrane. The flashing tape shall
be-pressed in place and fonned around the protrusion td,ensure a tight fit. A second layer of.like kind
membrane shall be applied over the flashing detail.
23. Vertical strapping of Tarco self adhering membranes'is.acceptable.
GENERAL LIMITATIONS—TARCO SELF-ADHERED UNDERLAY MENTS:
1. Fire classification is not part of this acceptance;refer to a current Approved Roofing Materials-Directory for fire
ratings of this product.
2. This acceptance.is for prepared roofing applications.'Miniuium deck requirements shall be in compliance with
applicable.building code.
3. Tarco self adhering underlayments shall be applied only when material interface temperatures are 400 F and
rising.
4. Tarco self-adhered underlaytnents,shall not be installed when any form of moisture such as water,dew,,rain,etc,
i`s'present on the substrate:
5. Tarco-self-adhered underlayments are to be applied to;a smooth,clean and dry surface,with the deck free from
irregularities:
6. Ensure roof has positive drainage prior to installation of Tarco self-adhered underlayments.
7. Tarco self-adhered underlayments shall not-be.applied over a preexisting roof membrane or system.
8. After installation of,Tarco,self-adhered membranes,wait a minimum of 48 hours before,roo'f loading of tiles.
9. Care should betaken during the loading'procedure to keep foot traffic'to a minimum and avoid dropping the
roof covering directly on thc.undcrlayment.
10. All tiles shall be staged(two tiles perpendicular to slope,fourtiles on.top parallel to slope)as per
manufacturer's requirements,not to exceed 6-high,to the standard maximum roof pitch of 6-:12 for flattiles
And 6:12 for'lugged tiles(See Tile Staging Method diagram below).
At roof slopes greater than the above limitations,,the use of loading battens or toe boards are required to load the
roof tile.
Tile Stagine Method
»nor a fin.,
ut+
Front View-Staged Tiles(Slope Side View-Staged Tiles(Slope l)
'NOA No.:16-111609
MIAMWADEcouMY Expiration Date.' 01/25/22
Approval Dater 01%12h7
Page 14 of 15