HomeMy WebLinkAboutProduct Approval i
TEAM ORN R
Unit Specifications
S0125 80145 80225 80120R S0166R
BTUs 80/80%80. 101,OO.Q 1f0U0; 143.,000. 110,UOQ . X2$xQ00 .
(water temp/ambientair/ 80/80/63 95,000 112,000 134,000 103,000 120,000
relative humidity)
80150(G3 . .. .` 62,QOU 75000 9,0,000 72,OOQ ;; 82,OQ0
C.O.P. 80/80/80 6.5 6.8 6.5 5.5 5.6
Coefficient ofPerformance
(water temp/ambient air/ 80/50/63 4.0 4.2 4.0 4.0 4.0
relative humidity)
Refrigerant ;'< 'R41OA " R410A R41pA
Electrical Heat or Heat&Cool H H H H &C H &C
kW lhput41
A-208-230/60/1 Voltage/Hz/Phase A A, B &G A, B, E& G A&B A, B, E& G
B-200-230/60/3 Max :,:A
60; A _60, A 60::. : ;:A
E-380-415/60/3 B 50 E3 50 `B 60 B0
0-460/60/3
Min.Circuit Ampacity A-40.5 A-42.1 A-42.1 A-38.5 A-42.1
B-31.0 B-33.3 B-31.0 B-33.3
G-14.2 E-18.4 E-18.4
G -16.2 G-16.2
Water Flow MtnJMaX Sgpmj 30/7 30170D/70 30170 : 30170
A Heater Bypass Kit Is required when flow rates exceed the maximum
Physical vght'pos) 268 328 328 ::268 >' 328
Length x Width x Height(in) 34"x 34"x 44" 34"x 34"x 44" 34"x 34.x 44" 34"x 34"x 44" 34"x 34"x 44"
Shipping Wetght{lost X90
Length x Width x Height(in) 38"x 36"x 49" 38"x 36"x 49" 38"x 36"x 49" 38"x 36"x x 36"x 49
FlBtfad in ai Cordantkwith AAYstantiarr 1160 w2mr templambient lr/relative huttiidity
$pecifications subjectfo.change
us
MM IN USA .
:z
57i�Ns'�+1flhiGi l5f�1M A3MV-PS
HeatWave SuperQuiet@ SQ1 2@Re),Re» Products» HeatWave SuperQuiet@ SQ120R
1
The NEWLY redesigned HeatWave
r��"'aJ y P•W ��, � * SuperQuiet® SQ120R comes equipped
with all standard features.The Patented
Titanium Heat Exchanger
at its core makes this unit a power-
house that's built to last. The SQ120R
features IceBreaker°technology which
allows you to heat and cool your pool.
f Plus, IceBreaker�'units extend the
swimming season longer than any other
heat pump by continuing to operate in
low temperatures.
• Corrosion proof cabinet with
AquaTop
Scroll Compressor-for quiet
operation
• Microprocessor Controls
• Off-Set Plumbing
heat oast and Axing estit �ti .
Document LTPOO98 rev 2a
Page Location: Home> Installation> Plumbing>Clearances
ICLEARANCES
• Proper air circulation is required for the heat pump to operate efficiently.Avoid placing objects near or
on top of the heat pump.This includes shrubbery and lawn furniture.These objects will also hinder
maintenance access.
• Avoid storing chemical containers near the heat pump.The chemicals can cause equipment damage.
Overhead Clearance
OverhanqwM
gutter
--J
OVERHEAD
5 feet
Rainiun-off and it 52 CMI
spanklersshould be
directed away from heater
HeatWave SuperQuiee and TropiCalo Crop View)
BACK
6inches
CM)
"IDES
S SIDES
I toot I foot
130 cm] 130 cm]
FIR NdT
3 feet
(91 CM]
c
7fz' "hir-
naand.Rauiwsxer:Runoff
A
. Irrigation water may damage heat pump components.Hive irrigation water directed away from the heat pump.
. The heat pump will withstand normal rainfall.Do not allow a roof slope to direct rainwater onto the heat pump_
Have a gutter installed on the roof edge to direct this water away from the heat pump. Or install the heat pump in
another location.
lanuiag fot;Cvnd�aaon `�.. v "
The heat pump can produce a large amount of water in the fotna of condensation.The amount of water
depends on air temperature and humidity.
. Install the heat pump with enough heigbt to allow for water drainage.
. Plan for water drainage disposal as needed.
ounm��'ad,Regai�epe�s -� --
. Build the heat pump pad out of concrete or another code-approved material.
• Confirm the pad can support the weight of the heat pump. See"Weights"on page 40.
. Elevate the pad enough to allow for drainage.
. Make sure the pad is flat and level.
. Have the pad extend at least 6 inches from the heat pump base in all directions.
. Do not install the heat pump on soil or grass.
. Do not allow the heat pump base to touch the buildings foundation-
Do not place the heat pump directly on a concrete floor inside a building.This can cause noisy equipment
vibration.Install vibration dampeners between the heat pump base and floor.
. Equipment pad must meet all requirements of authorities having code-related jurisdiction.
[AAnchormg-to Pad _
. Follow all applicable local,state,and national requirements regarding wind load anchoring.
. The shipping brackets used to tie the heat pump to the pallet are approved mounting(hurricane)brackets.They
can be used to anchor the heat pump to the pad `
. If needed, contact AquaCar Customer Support to obtain the,correct anchoring kit information.Please have the
heat pump model number and serial number when requesting support. See"Identifying Model Specifications"on
Page 39-
.3 --
3.3.a-Clearances
. Proper air circulation is required for the heat pump to operate efficiently.Avoid placing objects near or on top of
the heat pump.
and lawn furniture.These objects will also hinder maintenance access.
This includes shrubbery
. Avoid storing chemical containers near the heat pump.The chemicals can cause equipment damage.
Page-5