No preview available
HomeMy WebLinkAboutProduct Approval S4(/--3 !rf i ff= ,.20C r F:;t F 3MICAT ® F:aS RECM90 DEC 2 6 2019 To Whom It May Concern: ST. Lucie County., Perml!t g As outlined in the Florida Building Code, Extreme Metal Fabricators, LLC.will accept the installation of metal roofing panels over one layer of shingles or modified roofing, assuming all requirements of "Florida Building Code 5h Edition (2094) Section 9510 Reroofing, 9590.3 Recovering versus replacement", andlor"Florida Buiding Code 5°i Edition (2014) Residential Section 905.10 and Reroofing Section 907'have been met. It is important to ensure the existing substrate is not deteriorated, there is no entrapped moisture, meets all code requirements, and to install an approved separator underlayment,between the existing roofing and the metal panels, such as those that comply with ASTM D226 Type I or Type II or ASTM D 1970, or ASTM D 4869.The roofing contractor of record must verify the aforementioned requirements. Having confirmed code requirements, installation in this manner is approved by Extreme Metal Fabricators, LLC as the manufacturer. Plywood sheathing must be minimum 15732" CDX'plywood or'/"wood plank, solid decking, fastened per FBC requirements. The wood substrate must be inspected to ensure that it has not deteriorated and is acceptable as.a suitable substrate for additional roofing. Fasteners used should penetrate minimum '1" through structural decking or a minimum of 1" penetration into a thicker wood substrate, to insure pull-out values remain the same. Consideration should be given to the unevenness of the underlying shingles,which may telegraph through the new metal panels. As in all metal roofing, "oil canning" is an inherent condition that can occur in the panels_ Care should be taken during the installation, to observe the metal panels as they are installed, and adjust installation procedures, if possible, to help to minimize `oil canning". "Oil Canning"is an aesthetic issue not a structural issue, and not a cause for rejection. The energy savings that is normally observed after a new metal roof replaces the previously shingled roof, may be negated due to the underlying shingles holding heat energy much longer than a metal panel installed without shingles beneath it. REVIEWED FOR It is important to comply with allrequjrdments of the Florida Building Code, Fir eQi`MKAANGE code requirements. As always, authorities having jurisdiction, (building depar1rW I rE00 9, Y approve your demolition and reroof installation methods, prior to beginning work. B®CC Ffle Cop Extreme Metal Fabricators, LLC 9 2160 SW Poma Drive Palm City, FL 34990 ©(772) 223-4055 (Phone) w(772)781-7492 (Fax) EXSTO E i �- 'Florida Building Code Online �g�a `;•s v ����'°d`t��#r4�t�������a�•.i_ '�•"�a .� �„��7�'-�� ��� �*r'�i`��" � �z%*�.ir�z,._ _.., S,taut _ �i' SM Hmm S t.og In 1 1.tspr Registration i —TCPI-i Submit$wdwrge 51aes 6 rads i Pubrrt 111 S faC Staff= SM Site Map i Links 't Smrdl i Fioiida uctapprovalR � �xiIOpw:d usm haft Lisw' DEC L 6 2019 Product 0.00rmtal Meru>Product w JipaHrB;tian Ssardr>Aaollratinr+List>6yPIi[atlon QCRan 6 x x C a FU0378-R1 Application Type Revision ST. Lucie County, Permitting Code Version 2017 Application Status Approved Comments Archived Product Manufacturer Extreme Metal Fabricators LLC Address/Phone/Email 2160 SW Poma Drive Palm City,i9..34990 (772)872-8034 iivalidation@yahoo.com Authorized Signature Richard McKuhen fivalidatian@yahoo.com Technical Representative Richard McKuhen Address/Phone/Email 2160 SW Prima Drive Palin City,FL 34990 (772)872-8034 iichard@emfab.net i Quality Assurance Representative REVIEWED F O R Addr*/PhoneiEmatl CODE COMPLIANCE Category Roofing ST. LUCIE COUNTY Subcategory Metal Roofing OCC I Compliance Method Evaluation Report from a Florida Registered Architect or a Licer sed I Florida Professional Engineer Evaluation Report-Hardcopy Received i Florida Engineer or Architect Name who developed LOCKE BOWDEN the Evaluation Report Florida License PE-49704 Quality Assurance Entity Keystone Certifications,Inc. Quality Assurance Contract Expiration Date 04/22/2024 Validated By Zachary R.Priest,P.E. W Validation Checklist-Hardcopy Received Certificate of independence R20M 111 COI FL 2037a.1 NAILS-T IP 1.0 .032 ALUM sss.ndP Referenced Standard and Year(of Standard) Mandard Year TAS 125 2003 UL 1897 2012 UL 580 2006 Equivalence of Product Standards Certified By Sections from the Code ane Copy httac//www#laridabuildinLy-orF-r/0r/0r a00 dtl.asnx?naram--WGEVXUwtDoua%2flA4Z8n5C_-. 1/312018 1 CREEK Certificate of Authorization No.28824 ' 17520 Edinburgh Dr Tampa, FL 33647 TECHNICAL, SERVICES, LLC (813)480-3421 EVALUATION REPORT FLORIDA BUILDING CODE,6T"EDITION(2017) Manufacturer: ATLAS ROOFING CORPORATION Issued September 30, 2017 2000 Riveredge Parkway, Suite 800 -- — -- Atlanta, GA 30328 RMdEIV� - 0 (770)612-6267 www.atlasroofing.com D EEC 2 6 2019 Quality Assurance: UL LLC(QUA9625) ST. Lucie County, Permitting SCOPE Category: Roofing Subcategory: Underlayments Code Sections: 1507-1.1, 1518.4, 1523.1.1, 1523.6.5.2.1 Properties: Physical properties REFERENCES Eflft Report No. Standard Year PRI Construction Materials Technologies(TST6049) ATL-033-02-01 ASTM D 226 2009 PRI Construction Materials Technologies(TST6049) ATL-068-02-01 ASTM D 1970 2015a PRI Construction Materials Technologies(TST6049) ATL-068-02-01 ASTM D 4798 2011(2016) PRI Construction Materials Technologies(TST6049) ATL-068-02-01 TAS 110 2000 PRI Construction Materials Technologies(TST6049) ATL-069-02-01 ASTM D 1970 2015a PRI Construction Materials Technologies(TST6049) ATL-090-02-01 TAS 103 1995 PRI Construction Materials Technologies(TST6049) ATL-149-02-01 ASTM D 1970 2015a PRI Construction Materials Technologies(TST6049) ATL-164-02-01 ASTM D 1970 2015a PRI Construction Materials Technologies(TST6049) BWR-533-02-01 TAS 103 1995 PRI Construction Materials Technologies(TST6049) BWR-543-02-01 ASTM D 1970 2015a PRI Construction Materials Technologies(TST6049) MSA-004-02-01 ASTM D 1970 2015a PRI Construction Materials Technologies(TST6049) MSA-007-02-01 UL 1897 2012 PRI Construction Materials Technologies(TST6049) MSA-026-02-01 ASTM D 1970 2015a PRI Construction Materials Technologies(TST6049) WRMI-011-02-01 ASTM 1970 2015a PRI Construction Materials Technologies(TST6049) MSA-007-02-01 UL 1897 2012 PRI Construction Materials Technologies(TST6049) MSA-030-02-01 ASTM D 1970 2015a UL LLC(TST1740) 02-NK40952 ASTM D&176 UL LLC(TST1740) 02-NK40952 UL LLC(TST1740) 02-NK40952 26 0 UL LLC(TST1740) 02-NK40952 C® D 380�� � UL LLC(TST1740) 02-NK40952 LUCIE +C �p B®VC H File COPY ATL14001 AA FL17322-R4 Page 1 of 4 This evaluation report[is provided for State of Florida product approval under Rule 61 G20-3. The manufacturer shall notify CREEK Technical Services,LLC of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation reportidoes not express nor imply warranty, installation, recommended use,or other product attributes that are not specifically addressed;herein. , i i r , ����� ATLAS ROOFING CORPORATION Roofing Underlayments TECHNICAL SERYICEs,LLC PRODUCT DESCRIPTION i #15 Specification Felt ASTM D 226, Type I asphalt saturated organic felt underlayment for use in the HVHZ and non-HVHZ. #30 Organic Saturated Felt ASTM D 4869, Type II asphalt saturated organic felt underlayment for use in the non-HVHZ only. #30 Specification Felt ASTM D 226, Type II asphalt saturated organic felt underlayment for use in the HVHZ and non-HVHZ. #43 Base Sheet ASTM D 2626 asphalt saturated and coated, non-perforated, organic felt underlayment for use in the HVHZ and non-HVHZ. #90 Mineral Surface Roll ASTM D 6380, Class M asphalt-saturated organic roll roofing sheet for use in the Roofing HVHZ and non-HVHZ. Gorilla Guard®EVERFELT 30 Asphalt-saturated organic felt underlayment reinforced with glass fiber that meets the performance requirements of ASTM D 226, Type I for use in the HVHZ and non-HVHZ. Slatelfile Underlayment ASTM D 6380, Class M asphalt-saturated organic roll roofing sheet for use in the HVHZ and non-HVHZ. WeatherMaster@)Ice and ASTM D 1970 SBS modified, self-adhering underlayment reinforced with a Water 100 fiberglass mat and a granular surface for use in the HVHZ and non-HVHZ. The self-adhesive side is covered with a release film, which is removed during installation. WeatherMaster@)Ice and ASTM D 1970 SBS modified, self-adhering underlayment reinforced with a Water 200 fiberglass mat and a granular surface for use in the HVHZ and non-HVHZ. The self-adhesive side is covered with a split-release film, which is removed during installation- WeatherMaster@)Ice and ASTM D 1970 SBS modified, self-adhering underlayment reinforced with a Water 216 fiberglass mat and a granular surface for use in the HVHZ and non-HVHZ. The self-adhesive side is covered with a split-release film, which is removed during installation. WeatherMasterO Flexible Ice ASTM D 1970 SBS modified, self-adhering underlayment with plastic film surface and Water for use in the HVHZ and non-HVHZ. The self-adhesive side is covered with is split-release film,which is removed during installation. WeatherMaster@)Pro-Grade ASTM D 1970 SBS modified, self-adhering underlayment with a fiberglass mat Ice and Water reinforcement and a poly-fabric surface for use in the HVHZ and non-HVHZ. The self-adhesive side is covered with a release film, which is removed during installation. WeatherMaster@)Tile TAS 103 SBS modified, self-adhering underlayment with a fiberglass mat reinforcement and a poly-fabric surface for use in the HVHZ and non-HVHZ. The self-adhesive side is covered with a release film, which is removed during installation. ATL14001.4A FL17322-R4 Page 2 of 4 This evaluation report is provided for State of Florida product approval under Rule 61 G20-3. The manufacturer shall notify CREEK Technical Services,LLC of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are;not specifically addressed herein. I ' ATLAS ROOFING CORPORATION CREEKRoofing Underlayments TECHNICAL SERVICES, LLC APPLICATION METHOD Installation shall be in,accordance with the published manufacturer's installation instructions, the FBC, and the requirements below. Deck substrates shall be clean, dry, and free from any irregularities and debris. All fasteners in the deck shall be checked for protrusion and corrected prior to underlayment application. The roof deck shall be constructed of closely fitted plywood sheathing for new or existing construction. Plywood deck shall be installed in accordance with FBC requirements. Roof decks shall have no more than 1/8" gap at abutting joints. Exposure of the underlayments shall be limited to a maximum 30 days except as follows: a) #15 Specification Felt, #30 Specification Felt, and#40 Base Sheet—exposure for than 24 hours may adversely affect product performance b) WeatherMaster® Ice and Water 100, WeatherMaster@ Ice and Water 200, and WeatherMaster® Ice and Water 216—maximum 30 days c) WeatherMaster® Pro-Grade Ice and Water and WeatherMaster® Flexible Ice and Water—maximum 30 days d) WeatherMaster® Tile—maximum 90 days Self-adhering underlayments may be adhered to primed or unprimed plywood substrates in the non-HVHZ. Roof coverings shall be mechanically fastened through the underlayment to the roof deck except as follows (or as indicated in other current FBC product approval documents): a) WeatherMaster® Pro-Grade Ice and Water or WeatherMaster® Tile—ICP Adhesives Polyset AH-160 b) Slate/Tile Underlayment or#90 Mineral Surface Roll Roofing — Convenience Products Touch n' Seal Storm Bond Roof Tile Adhesive, Dow TileBond, or ICP Adhesives Polyset AH-160 Allowable Roof Coverings: Metal Roof:^. Zompositwor:;. -Wood Asphalt: Panels and: Photovoltaic 'Shingles and Slate Clay and Underlayment. Shingles 'Shingles: Shingles Shakes ::Shingles. Concrete Tile` #15 Specification Felt Y Y Y Y2 Y N #30 Organic Saturated Felt Y Y Y Y Y N #30 Specification Felt Y Y Y Y Y Y #43 Base Sheet Y Y Y N Y Y #90 Mineral Surface Roll Roofing Y' N N N N Y Gorilla Guard®EVERFELT 30 Y Y Y YZ Y N SlateTle Underlayment Y' N N N N Y WeatherMaster®Ice and Water 100 Y Y Y N Y N WeatherMastea Ice and Water 200 Y Y Y N Y N WeatherMasterO Ice and Water Y Y Y N Y N 216 WeatherMasterO Flexible Ice and Y Y Y N Y N Water WeatherMaster®Pro-Grade Ice Y Y Y N Y N and Water WeatherMaster®Tile Y Y Y N Y Y Notes: 1)Open valley applications per 1507.2.9.2 2)Wood shingles only ATL14001.4A FL17322-R4 Page 3 of 4 This evaluation report is provided for State of Florida product approval under Rule 61 G20-3. The manufacturer shall notify CREEK Technical Services,LLC of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty, installation, recommended use, or other product attributes that are not specifically addressed herein. i GREEK ATLAS ROOFING CORPORATION Roofing Underlayments TECHNICAL SERVICES,LLC WIND RESISTANCE(NON-HVHZ ONLY) The Maximum Design Pressures shown below were calculated using a 2:1 margin of safety per FBC Section 1504.9. Underlayment System No.1—WeatherMaster@ Tile only Roof Deck: Min. 15/32-inch CDX plywood attached to wood supports spaced a maximum 24"o.c. Underlayment: WeatherMasterS Tile shall be fully adhered to the optionally primed plywood deck. Maximum Design -52.5 psf Pressure: LIMITATIONS 1) Fire Classification is not within the scope of this evaluation. 2) Roof slope limitations shall be in accordance with FBC requirements. 3) Installation of the evaluated product shall comply with this report,the FBC, and the manufacturer's published application instructions. Where discrepancies exist between these sources, the more restrictive and FBC compliant installation detail shall prevail. 4) Products described within this report may be used as described in other current FBC product approval documents. 5) Roof coverings shall not be adhered directly to the underlayment unless otherwise approved in this or other current FBC product approval documents. 6) All products listed in this report shall be manufactured under a quality assurance program in compliance with Rule 61G20-3. COMPLIANCE STATEMENT The products evaluated herein by Zachary R. Priest P.E. have demonstrated compliance with the Florida Building Code, 6►'Edition(2017)as evidenced in the referenced documents submitted by the named manufacturer. %,G%XP�G E N' 2 017 09 3 0 ' No 74021 /� •2 12:44. 2 7� �= -04'00' STATE OF :4� AllO R t p P'NZachary R. Priest, P.E. Florida Registration No. 21 Organization No.ANE9641 CERTIFICATION OF INDEPENDENCE CREEK Technical Services,LLC does not have,nor will it acquire,a financial interest in any company manufacturing or distributing products under this evaluation. CREEK Technical Services,LLC is not owned,operated,or controlled by any company manufacturing or distributing products under this evaluation. Zachary R. Priest, P.E.does not have, nor will acquire, a financial interest in any company manufacturing or distributing products under this evaluation. Zachary R.Priest,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the product. END OF REPORT i ATL14001 AA I. FL17322-R4 Page 4 of 4 This evaluation report is provided for State of Florida product approval under Rule 61 G20-3. The manufacturer shall notify CREEK Technical Services,LLC of any product changes or quality assurance changes throughout the duration for which this report is valid. This evaluation report does not express nor imply warranty,installation, recommended use, or other product attributes that are'not specifically addressed herein. I