HomeMy WebLinkAboutNotice of Acceptance FILE COPY
Ml�aauE
RECEIVED
MIAMI DADE COUNTY '
JAN 16 � PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RES CES(RER) 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION
ST. Lucie County,Permitting Ivva►m,Florida 33175-2474
goo „ b T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE OA www.miamidade.eov/economy
Polyglass USA,Inc. C
150 Lyon Drive ODE COMPLIANCE
Fernley,NV 89408 ST. LUCIE COUNTV
SCOPE: ®. G� 2-0
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County and other*areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control Section
(In Miami Dade County)and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this
product or material tested for quality assurance purposes.If this product or material fails.to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined.by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein,and has been designed to comply with the Florida-Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.-
DESCRIPTION:
ode.DESCRIPTION:Polyglass Self-Adhered Roof System over Wood Decks -
LABELING:Each unit shall bear-a permanent label with.the manufacturer's name or logo,city,state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,
for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA# 17-1016.01 and consists of pages 1 through 38.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 19-0311.04
MIAMFDADE COUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
h
ROOFING ASSEMBLY APPROVAL
Category Roofing
Sub-Category: Modified Bitumen
Materials SBS/APP/TPO
Deck Type: Wood
Maximum Design Pressure -112.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions Specification Description
Polyanchor 250'x 48" ASTM D 4601, A polymer woven,high performance,synthetic base
Type II sheet.
Polyglass G2 Base 108'x 36" ASTM D 4601, Asphalt-coated fiberglass reinforced base sheet
Type H
Elastoshield HT 65' 8"x 3'3-3/8" ASTM D 6162 SBS modified asphalt coated fiberglass/polyester
reinforced base sheet.
XtraFlex SBS HT 65' 8"x 3',3-3/8" ASTM D 6162 SBS modified asphalt coated fiberglass/polyester
Base 650 reinforced base sheet.
Elastobase 65'2"x 3'3-3/8" ASTM D 6163, SBS modified.asphalt coated fiberglass reinforced
Type I base sheet.
Elastoflex SA V 66' 8"x 3'3 3/s" ASTM D 6163, Self-adhered,fiberglass reinforced,SBS modified
Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA V FR 66' 8"x 3' 3-3/8" ASTM D-6163, Self-adhered,fire-rated,fiberglass reinforced,SBS
Type I modified bitumen membrane witha.self-adhering back
face and a smooth top surface.
Elastoflex SA V 66' 8":0'V/8" ASTM D 6163, SeIf-adhered,fiberglass reinforced,SBS modified
PLUS Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA V 66' 8"x 3'3-3/8" ASTM D 6163, Self-adhered,fire-rated,fiberglass reinforced,SBS
PLUS FR Type I modified bitumen membrane with a self-adhering back
face and a smooth top surface.
XtraFlex SBS Base 66' 8"x 3'3-3/8" ASTM D 6163, Self-adhered,fiberglass reinforced,SBS modified-
SA Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Xtr0lex SBS Glass 65' 8"x 3'3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced
Base Type L base sheet.
Elastobase P 65' 8"x 3'3-3/8" ASTM D 6164, SBS modified asphalt coated polyester reinforced base
Type I sheet.
Elastoflex SA P 32' 10"x 3'3-3/8" ASTM D 6164, Self-adhered,fiberglass reinforced,SBS modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
NOA No.: 19-0311.04
MIAMIDADE COUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
i
Elastoflex SA P FR 32' 10"x3' 3-3/8" ASTM D 6164, Self-adhered,fire-rated,polyester reinforced,SBS
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polyfresko G SBS SA 32' 10"x 3' 3-'/s" ASTM D 6164, Self-adhered,fiberglass reinforced,SBS modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko G SBS SA 32' 10"x 3' V/8" ASTM D 6164, Self-adhered,fire-rated,fiberglass reinforced,SBS
FR Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polyreflect 32' 10"x 3'V/8" ASTM D 6164, Self-adhered,polymer,SBS modified bitumen
Type I membrane with a self-adhering back face and a smooth
top surface.
XtraFlex SBS G SA 32' 10"x 3' 3-3/8" ASTM D 6164, Self-adhered,fire-rated,polyester reinforced,SBS
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polybond 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a bum off polyethylene back
face and a smooth or sanded top surface.
Polyflex 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
XtraFlex APP S 32' 10"x3'3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a bum off polyethylene back
face and a smooth or sanded top surface.
PolyKool 32' 10"x 3'V/8" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
XtraFlex Kool APP S 32' 10"x 3' 3-N8" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
SA Type I bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
Polyflex SA P 32' 10"x 3'V/8" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex SA P FR 32' 10"x 3'V/8" ASTM D 6222, Self-adhered,fire-rated,polyester reinforced,APP "
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polyfresko G APP SA 32' 10"x 3' V/8" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko G APP SA 32' 10"x 3' 3j/g" ASTM D 6222, Self-adhered,fire-rated,polyester reinforced,APP
FR Type I modified bitumen membrane with a self-adhering back
face and a granule top surface
XtraFlex APP G SA 32' 10"x 3' V/8" ASTM D 6222, Self-adhered,fire-rated,polyester reinforced,APP
Type I modified bitumen -membrane with a self-adhering back
face and a granule top surface.
NOA No.: 19-0311.04
r7MrtI4=eFig l4011 Expiration Date: 10/11/22
Approval Date:03/21/19
9
Polyglass APP Base 65' 8"x 3'3-N8" ASTM D 6509, APP modified asphalt coated fiberglass reinforced
Type I base sheet.
PG 100 1,3,5,50,55 gal, ASTM D41 A penetrating solution of solvent and a blend of
tube or 17 oz.spray selected asphalts used to promote adhesion.
can
PG 350 1,3,5,50,55 gal.or ASTM D3019 .A fibered rubberized adhesive designed for use with
tube Type III modified bitumen membranes.
PG 400 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use in
tube ASTM D3409 dry or damp conditions.
PG 425 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use in
tube ASTM D3409 dry or damp conditions.
PG 450 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement.
tube
PG 500 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use
tube with modified bitumen membranes.
POLYPLUS 35 1,3,5,50,55 gal.or ASTM D3019 A fibered rubberized adhesive designed for use with
tube Type III modified bitumen membranes.
POLYPLUS 45 1,3,5,50;55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement.
tube
POLYPLUS 50 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use
tube with modified bitumen membranes.
XtraFlex 10 1,3,5,50,55 gal, ASTM D41 A penetrating solution of solvent and a blend of
tube or 17 oz.spray selected asphalts used to promote adhesion.
can
XtraFlex 35 1,3,5,50,55 gal.or ASTM D3019 A fibered rubberized adhesive designed for use with
tube Type III modified bitumen membranes.
XtraFlex 50 Premium 1,3,5,50,55 gal:or ASTM D4586 A thick,fibered,rubberized flashing cement for use
Modified Wet/Dry tube with modified bitumen membranes.
Cement
WB-3000 5 gallon pail Proprietary A low-VOC,water-based acrylic primer to enhance
adhesion of self-adhered membranes.
NOA No.: 19-0311,04
MAMI•DADecoutm Expiration Date: 10/11/22
Approval Date:03/21/19
APPROVED INSULATIONS:
TABLE 2
Product Name Product Description Manufacturer
(With Current NOA)
Polytherm-H Polyisocyanurate foam insulation Polyglass USA,Inc.
Polytherm Polyisocyanurate foam insulation Polyglass USA,Inc.
Polytherm G Polyisocyanurate foam insulation Polyglass USA,Inc.
XtraFlex Polyiso Polyisocyanurate foam insulation Polyglass USA,Inc.
XtraFlex Polyiso G Polyisocyanurate foam insulation Polyglass USA,Inc.
ACFoam II Polyisocyanurate foam insulation Atlas Roofing Corp
ACFoam-III Polyisocyanurate foam insulation Atlas Roofing Corp
Structodek High Density Fiberboard Roof Wood fiber insulation board Blue Ridge Fiberboard,Inc.
Insulation
DensDeck,DensDeck Prime Gypsum insulation board Georgia-Pacific Gypsum LLC
H-Shield Polyisocyanurate foam insulation Hunter Panels,LLC
H-Shield CG Polyisocyanurate/perlite composite insulation Hunter Panels,LLC
ENRGY-3 Polyisocyanurate foam insulation Johns Manville Corp.
Fesco Board Expanded mineral fiber .Johns Manville Corp.
Multi-Max FA-3 Polyisocyanurate foam insulation Rmax Operating,LLC.
SECUROCK Gypsum-Fiber Roof Board Fiber reinforced coverboard United States Gypsum
Corporation
N.OA No.: 19-0311.04
tau �•nAAPPROVED
rry Expiration Date: 10/11/22
Approval Date:03/21/19
APPROVED FASTENERS:
TABLE 3
Fastener Product Product Manufacturer
Number Name Description Dimensions (With Current NOA)
1. Dekfast DF-912-PH3 Insulation fastener for wood, SFS Group USA,Inc.
steel and concrete decks
2. DekfastDF-#14-PH3 Insulation fastener for wood, Various SFS Group USA,Inc.
steel and concrete decks
3. Dekfast DF-#15-PH3 Insulation fastener for wood, Various SFS Group USA,Inc.
steel and concrete decks
4. Dekfast PLT-H-2-7/8 Galvalume hex stress plate. 2 7/8"x SFS Group USA,Inc.
3 '/A"
5. #14 Roofgrip Insulation and membrane Various OMG,Inc.
fastener
6. Flat Bottom Metal Plate A2-SS aluminized steel plate 3"square OMG,Inc.
7. Trufast#14 HD Fastener Insulation fastener for steel and Altenloh,Brinck&Co.
wood decks U.S.,Inc.
8. Trufast 3"Metal Insulation Round Galvalume AZ50 steel 3.23 round Altenloh,Brinck&Co.
Plate plate 3"round U.S.,Inc.
9. Polygrip Fasteners#12 Insulation fastener for wood, Various Polyglass USA,Inc
steel and concrete decks
10. Polygrip Fastener#14 Insulation fastener for,wood, Various Polyglass USA,Inca
steel and concrete decks
11. Polygrip Fastener#15 Insulation fastener for wood, Various Polyglass USA,Inc.
steel and concrete decks
12. Polygrip Hex Plates Galvalume hex stress plate. 2 7/8"x Polyglass USA,Inc
3 ''/a"
13. OMG 3 in.Ribbed Galvalume stress plate. 3"round OMG,Inc.
Galvalume Plate(Flat)
14. OMG 3"Galvalume Steel Galvalume stress plate. 3"round OMG,Inc.
Plate
15. Dekfast PLT-R-3 Galvalume stress plate. 3"round SFS Group-USA,Inc.
16. Millennium One-Step A two component,low rise, Adco Products,Inc.dba"
Foamable Adhesive polyurethane foam adhesive Royal Adhesives&
Sealants
17. Millennium One Step Green A two component,low rise, Adco Products,Inc.dba
Foamable Insulation polyurethane foam adhesive Royal Adhesives&
Adhesive Sealants
18. Millennium PG-1.Pump A two component,low rise, Adco Products,Inc.dba
Grade-Adhesive polyurethane foam adhesive Royal Adhesives&
Sealants
NOA No.: 19-0311.04
Mwru•a4pe couw7�r Expiration Date: 10/11/22
Approval Date:03/21/19
APPROVED SURFACING:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions.
Number Product Product Application Specification Manufacturer
Name Description Rate
1. Gravel To be installed in a flood coat 4001bs/sq N/A Generic
of approved asphalt at 601bs/sq
2. Slag To be installed in a flood coat 3001bs/sq N/A Generic
of approved asphalt at 60 lbs/sq
3. KM Acryl 15 A premium white or tinted 1-1'/z gal/sq ASTM D6083 Polyglass USA,
clastomeric acrylic based roof Inc.
coating(water-based). A
polyester fabric may be used
for reinforcement with this
coating.
4. KM Acryl 15 QS ' A premium white or tinted 1-1'/2 gal/sq ASTM D6083 Polyglass USA,
quick setting,elastomeric Inc.
acrylic based roof coating
(water-based). A polyester
fabric may be used for
reinforcement with this
coating.
5. KM Acryl 25 A premium white or tinted 1-1'/2 gal/sq ASTM D6083 Polyglass USA,
elastomeric acrylic based roof Inc.
coating(water-based). A
polyester fabric may be used
for reinforcement with this
coating. .
6. KM Acryl 25 QS A premium white or tinted 14%2 gal/sq ASTM D6083 Polyglass USA,
quick setting,elastomeric Inc.
acrylic based roof coating
(water-based). A polyester
fabric may be used for
reinforcement with this
coating.
7. KM-PS#220 A single component,solvent, 1.25 gal/sq ASTM D6694 Polyglass USA,
white or tinted,silicone Inc.
coating.
8. KM-PS#250 A premium grade high solids, 1.25 gal/sq ASTM D6694 Polyglass USA,
white or tinted,single Inc.
component,moisture cure,
fluid applied silicone coating
NOA No.: 19-0311.04
MIAMI•DADE COU Expiration Date: 10/11/22
Approval Date:03/21/19
APPROVED SURFACING:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions.
Number Product Product Application - Specification Manufacturer
Name Description Rate
9. PG 300 An asphalt cutback fibered roof 1'/2-2 gal/sq ASTM D4479 Polyglass USA,
coating. May be applied by Inc.
brush or spray equipment to
rejuvenate aged BUR
10. PG 600 Non-fibered aluminum roof %2-1 gal/sq ASTM D2824 Polyglass USA,
coating. Type I Inc.
11. PG 650 Fibered aluminum roof coating. 1'/2-2 gal/sq ASTM D2824 Polyglass USA,
Type III Inc.
12. PG 700 A premium white or tinted 1-1'/2 gaUsq ASTM D6083 Polyglass USA,
elastomeric acrylic based roof Inc. .
coating(water-based). A
polyester fabric-may be used
for reinforcement with this
coating.
13. PG 700 QS A premium white or tinted 1-1'/2 gal/sq ASTM D6083 Polyglass USA,
quick setting,elastomeric Inc.
acrylic based roof coating
(water-based). A polyester
fabric may be used for
reinforcement with this
coating.
14. PG 800 An asphalt based,non-fibered 3 gal/sq in two ASTM D1227 Polyglass USA,
clay emulsion coats.' Inc.
15. PolyBrite 70 A premium white or tinted 1-1%2 gal/sq ASTM D6083 Polyglass USA,
elastomeric acrylic based roof Inc.
coating(water-based). A
polyester fabric may be used
for reinforcement with this
coating..
16. PolyBrite 70 QS A premium white or tinted 1-1'/2 gal/sq ASTM 1)6083 Polyglass USA,
quick setting,elastomeric Inc.
acrylic based roof coating
(water-based). A polyester
fabric may be used for
reinforcement with this
coating.
17. PolyBrite 90 A premium grade high solids, 1.25 gal/sq ASTM D6694 . Polyglass USA,
white or tinted,single Inc.
component,moisture cure,
fluid applied silicone coating
NOA No.: 19-0311.04
h IAMM ape COUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
APPROVED SURFACING:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions.
Number Product Product Application Specification Manufacturer
Name Description Rate
18. PolyBrite 95 A single component,white or 1.25 gal/sq ASTM D6694 Polyglass USA,
tinted,solvent,moisture cure Inc.
silicone coating.
19. POLYPLUS 60 Non-fibered aluminum roof '/2-1 gal/sq ASTM D2824 Polyglass USA,
coating. . Type I Inc.
20. POLYPLUS 65 Fibered aluminum roof coating. 116-2 gal/sq ASTM D2824 Polyglass USA,
Type III Inc.
21. XtraFlex 60 Aluminum Non-fibered aluminum roof 16-1 gal/sq ASTM D2824 Polyglass USA,
Roof Coating coating. Type I Inc.
22. XtraFlex 65 Aluminum Fibered aluminum roof coating. 1%2-2 gal/sq ASTM D2824 Polyglass USA,
Roof Coating Fibered Type III Inc.
23. XtraFlex 70 Premium A premium white or tinted 1-1'/2 gaUsq ASTM D6083 Polyglass USA,
Acrylic FR Roof elastomeric acrylic based roof Inc.
Coating coating(water-based). A
polyester fabric may be used
for reinforcement with this.
coating.
24. XtraFlex 80 Emulsion An asphalt based,non-fibered 3 gaUsq in two ASTM D1227 Polyglass USA,
Roof Coating clay emulsion coats Inc.
25. XtraFlex 30 An asphalt cutback fibered roof 1'/2-2 gal/sq ASTM D4479 Polyglass USA,
Bituminous Roof coating. May be applied by Inc.
Coating Fibered brush or spray equipment to
rejuvenate aged BUR
26. XtraFlex SRC 8000 A single component,white or 1.25 gal/sq ASTM D6694 Polyglass USA,
tinted,solvent,,moisture cure Inc.
silicone coating.
27. XtraFlex SRC 9600 A premium grade high solids, 1:25 gal/sq ASTM D6694 Polyglass USA,
white or tinted,single Inc.
component,moisture cure,
fluid applied silicone coating
NOA No.: 19-0311.04
MAM4403ADE couNW Expiration Date: 10/11/22
Approval Date:03/21/19
EVIDENCE SUBNIITTED:
Test Aaency Test Name/Report Report No. Date
Factory Mutual Research 4470 2W7A7.AM 08.04.94
Corporation 4450 2D5A9.AM 0622.99
4470 3000857 01.12.00
4470 3004091 01.12.00
4470 3001334 02.15:00
4470 3014692 08.05.03
4450 3014751 08.27.03
4450 3019317 06.30.04
4470 3024311 , 11.01.06
4470 3012321 07.29.07
4470 3036182 07.31.09
4470 RR202591 10.22.15
Trinity I ERD TAS 114 11752.09.99-1 02.08.00
TAS 114 11751.05.03 05.30.03
TAS 117(B)-ASTM D903 020841.06.04 06.02.04
TAS 114 02762.03.05 03.30.05
TAS 114 02764.09.05 09.09.05
TAS 114 P1739.01.07 01.23.07
TAS 114 P1734.07.06-R1 02.27.07
TAS-117(B)-ASTM D6862 C8500SC.11.07 11.30.07
TAS 114&FM 4.470 P7860SCA 1.07 11.30.07
TAS 114(D)—ASTM-D1876 P10070.10.08 10.09.08
TAS 114(IT) P13760.09.09 09.10.09
FM 4470&TAS 114 P33970.03.11 03.15.11
ASTM D6163/ASTM D 4601 P33960.03.11 03.15.11
ASTM D6163 P37590.03.13-2-R1 02.05.13
ASTM D6164 P37590.03.13-3A 03.06.13
TAS 114 P1738.02.07-R2 04.29.13
TAS 114&TAS 117(B) 11757.04.01-1-R1 04.30.13
ASTM D6509 P37590.03.13-1-R1 06.26.,13
ASTM D6222 P37590.03.13-5-R1 07.01.13
ASTM D6164 P37590.07.13-1 07.02.13
TAS 114&FM 4474 P41630.08.13 08.06.13
ASTM D4601 /TAS 117 P45940.09.13 09.04.13
ASTM D6222 P37590.09.13 09.12.13
ASTM D4601 /TAS 117 P45970.05.14 05.12.14
ASTM D6162 SC5170.05.15 05.08.15
ASTM D6162 SC5170.12.15-1 12.29.15
TAS 114&FM 4474 PLYG-SC8905.05.16-1 05.17.16
TAS 114&TAS 117(B) 11757.12.00-1-R2 04.05.17
PRI Construction Materials ASTM D6222 PUSA-061-02-02 01.28.08
Technologies ASTM D6163 PUSA-064-02-02 0227.08
ASTM D6222 PUSA-062-02-02 12.04.08
ASTM D6694 PUSA-134-02-01 05.16.14
NOA No.: 19-0311.04
t4u MN)ADE eOUbr Y Expiration Date: 10/11/22
0 Approval Date:03/21/19
EVIDENCE SUBNHTTED:
Test Agency Test Name/Report Report No. Date
ASTM D6694 PUSA-135-02-01 05.16.14
TAS 117(3) PUSA-202-02-01 05.08.17
FM 4470&TAS 114 PUSA 202-02-02 05.23.17
NOA No.: 19-0311.04
MIA 41-DMECOUNiY Expiration Date: 10/11/22
Approval Date:03/21/19
N
APPROVED ASSEMBLIES:
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19/32"or greater plywood or wood plank,fastened at 24"spans with#8 wood screws at 6"o.c..
System Type A(1): All insulation layers,are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase,Elastoshield HT,GAFGLAS#75,Polybond*Polyflex*,Polyglass G2
Base,XtraFlex APP S*,XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to
the deck as described below:
*with OMG fasteners and Flat Bottom Metal Plates.
Fastening#1.: Attach base sheet using 11 ga.annular ring shank and 1-5/8"diameter tin caps spaced 8"o.c,
in a 4"lap and 8"o.c.in three equally spaced staggered rows in the center of the sheet.
Fastening#2: Attach base sheet using OMG#14 Roofgrip fasteners and Flat Bottom Metal Plates,Dekfast
DF-#14-PH3 with Dekfast PLT-H-2-7/8 plates or Polygrip Fasteners#14 with Polygrip Hex
Plates or Trufast#14 HD Fasteners with Trufast 3"Metal Insulation Plates spaced 12"o.c. in a
4"lap and 12"o.c.in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver(Optional) Insulation Fasteners Fastener
able 3 Density/fe
Polytherm,Polytherm-H,Polytherm G,XtraFlex Polyiso,XtraFlex Polyiso G,ACFoam-II,ACFoam-III,11-
Shield,Multi-Max FA-3,ENRGY-3
Minimum 1.5"thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a-rate of 20-40 lbs/100 fe. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Top Insulation Laver Insulation Fasteners Fastener
able 3 Density/ftp
DensDeck,DensDeck Prime,SECUROCK Gypsum-Fiber Roof Board
Minimum'/411 thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 20-40 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
NOA No.: 19-0311.04
Muu�i nAue courn r Expiration Date: 10/11/22
Approval Date:03/21/19
Primer: Apply WB-3000 at 1 gal.per 300 sq.ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self-adhered.
Ply Sheet: One or more plies of Elastoflex SA V,EIastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Poly-flex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.-
Maximum
lassification.Maximum Design
Pressure: -52.5 psf;(See general limitation#7.)
NOA No.: 19-0311.04
MIAMI-DA DE couNW Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: ' SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19/32'or greater plywood—or wood plank,fastened at 24"spans with#8 wood screws at 6"o.c.
System Type A(2): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase,Elastoshield HT,Elastobase P,Polybond,Polyflex,Polyglass G2 Base,
XtraFlex APP S,XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck
as described below:
Fastening: Attach base sheet using OMG#14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c.in a 4"lap and 12"o.c.in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver(Optional) Insulation Fasteners Fastener
able 3 Density/W
Polytherm,Polytherm-H,Polytherm G,XtraFlex Polyiso,XtraFlex Polyiso G,ACFoam-II,ACFoam-III,H-
Shield,Multi-Mag FA-3,ENRGY-3
Minimum 1"thick N/A N/A
Toa Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft2
DensDeck,DensDeck Prime,SECUROCK Gypsum-Fiber Roof Board
Minimum 1/4"thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Primer: Apply WB-3000 at 1 gal.per 300 sq.ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self-adhered.
Ply Sheet.- One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
NOA No.:19-0311.04
MIAMI-DAD 0 COUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
a
Surfacing: Install one of the approved surfacing,products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -60 psf;(gee general limitation V.)
NOA No.: 19-0311.04
MANCADECOUNTYM Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19/32'or greater plywood or-wood plank,fastened at 24"spans with 8d common nails at 4"o.c.
or#8 wood screws at 6"o.c.
System Type A(3): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga.Annular ring shank and.1-5/8"diameter tin caps spaced 8"o.c.
in a 4"lap and 8"o.c.in three equally spaced staggered rows in the center of the sheet.
One of more of the following:
Base Insulation Laver(Ontional) Insulation Fasteners' Fastener
Table 3 Densiy ft2
Polytherm,Polytherm-H,Polytherm G,XtraFlex Polyiso,XtraFlex Polyiso G,ACFoam-H,ACFoam-III,H-
'Shield,Multi-Max FA-3,ENRGY-3
Minimum 1"thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ft. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as.a top layer placed with the polyisocyanurate side facing down.
Toa Insulation Laver Insulation Fasteners Fastener
able 3 Density/fe
Dens Deck,Dens Deck Prime,SECUROCK Gypsum-Fiber Roof Board
Minimum'/a"thick N/A N/A
Note:,Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 20-40 lbs/100 fe. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the,final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanarate side facing down.
Primer: Apply WB-3000 at 1 gal.per 300 sq.ft.
(Optional).
Base Sheet: One ply of Elastoflex SA V,Elastoflex SA V FR or Elastoflex SA V PLUS,Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self-adhered.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V ER or Elastoflex SA V PLUS,
(Optional) Elastoflex SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
NOA No.: 19-0311.04
WAMI ADE OuNTY Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA,XtraFlex SBS G SA,
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification. _
Maximum Design
Pressure: -52.5 psf;(See general limitation 47.)
NOA No.: 19-0311.04
MwMi•oane eoutanr Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19/32'or greater plywood or wood plank fastened at 24"spans with#8 wood screws at 6"o.c.
System Type A(4): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase,Elastoshield HT,Elastobase P XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened as below:
Fastening: 12 ga.Annular ring shank nails and'1-5/8"tin-caps attached 6"o.c.in 4"lap and 6"o.c.in four
equally spaced staggered rows.
Base Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft2
ACFoam-II,Polytherm,Polytherm G,XtraFlex Polyiso,XtraFlex Polyiso G,ACFoam-III,H-Shield,
Polytherm-H,H-Shield CG,Multi-Max FA-3,ENRGY 3
Minimum 1"thick N/A N/A
Note:All insulation shall be adhered to the anchor sheet with Millennium One-Step Foamable Adhesive,
Millennium One Step Green Foamable Insulation Adhesive or Millennium PG-1 Pump Grade Adhesive applied
over rows of tin-caps in continuous rows 7"o.c. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used.only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite"insulation panels may be
used as a top layer placedwith the polyisocyanurate side facing down.
Primer: Apply WB-3000 at 1 gal.per 300 sq.ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self-adhered.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polytlex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -60 psf;(See general limitation#7.)
NOA No.: 19-0311.04
Mw41•DA DE CouNTY Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: Min.19/32'plywood(15/32"for re-roof)or wood plank,fastened at 24"spans with 8d common
nails at 6"o.c.
System Type C(1): All layers-of insulation are mechanically attached to roof deck.Membranes subsequently
adhered to insulation.
All General and System Limitations.apply.
One or more of the following
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
Any approved Polyisocyanurate listed-in Table 2
Minimum 1.0"thick N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes, and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. .
Toa Insulation Laver Insulation Fasteners Fastener
.able 3 Density/fe
SECUROCK Gypsum-Fiber Roof Board
Minimum'/"thick 2 with 4 or 15;10 with 12;5 1:2 ftz
with 6,13 or 14;7 with 8;
DensDeck Prime
Minimum I/4"thick 2 with 4; 10 with 12;5 with 1:2 ft2
6 or 14;7 with 8;
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used,the number of fasteners
shall be increased-maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer:. Apply WB-3000 at 1 gal.per 300 sq.ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self-adhered.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self--adhered.
Membrane: One ply of Elastoflex SA P FR,Polyflex SA P FR,Polyfresko G APP SA FR,Polyfresko G
SBS SA FR,PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP SA or XtraFlex
SBS G SA self-adhered.
NOA No.: 19-0311.04
Mwrn or�ue eouNry Expiration Date: 10/11/22
Approval Date:03/21/19
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
-Pressure: -45 psf;(See General limitation V.)
NOA No.: 19-0311.04
MIAMI•DADE COUNTY Expiration Date: 10/11/22
FAZIMSYRIJ
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19732'or greater plywood or wood plank,fastened at 24"spans with 8d common nails or wood
screws at 4"o.c.
System Type C(2): All layers of insulation are mechanically attached to roof deck.Membranes subsequently
adhered to insulation.
All General and System Limitations apply.
One or more of the following
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
Any approved Polyboeyanurate listed in Table 2
Minimum 1.5"thick N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing_ Application Standard RAS 117 for
insulation attachment.
Ton Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft2
Structodek High Density Fiberboard Roof Insulation
Minimum'/"thick 2 with 4;10 with 12 1:1.33 W
DensDeck
Minimum'/a"thick 2 with 4;10 with 12 1:1.33 ft'
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used,the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal.per 300 sq.ft.to DensDeck prior to application of self-adhered base
(Optional) sheets.
Base Sheet: One ply of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self-adhered.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA,XtraFlex SBS G SA,
self-adhered.
NOA No.:19-0311.04
MIAM�•DADEeOUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -67.5 psf;(See General limitation#7.)
NOA No.: 19-0311.04
M I41•DADE COUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19/32'or greater plywood or,wood plank,fastened at 24"spans with 8d common nails at 4"o.c.
System Type C(3): All layers-of insulation are mechanically attached to roof deck.Membranes subsequently
adhered to insulation.
All General and System Limitations apply.
One or more layers of the following:
Base Insulation Laver Insulation Fasteners Fastener
able 3 Density/fe
Any approved Polyisocyanurate listed in Table 2
Minimum 1.5"thick . N/A . N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density." Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Top Insulation Laver Insulation Fasteners Fastener
able 3 Density/W
Structodek High Density Fiberboard Roof Insulation
Minimum'/2"thick 2 with 4; 10 with 12 1:1.33 ff
DensDeck
Minimum 1/4"thick 2 with 4; 10 with 12 1:1.33 ft'
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal.per 300 sq.ft.to DensDeck prior to application of self-adhered base
(Optional) sheets.
Base Sheet: One ply of Elastoflex SA V,Ela9toflex SA V FR,Elastoflex SA V PLUS,Elastoflex SA V
PLUS FR or XtraFlex SBS Base SA self-adhered.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
(Optional) SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
NOA No.: 19-0311.04
MIAMIMADE COUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.-
Maximum Design
Pressure: -67.5 psf;(See General limitation#7.)
NOA No.: 19-0311.04
MIAMI•DADE 0 UN7Y Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type:. SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19/32"or greater plywood or wood.plank,fastened at 24"spans with wood screws at 6"o.c.
System Type C(4): All layers of insulation are mechanically attached to roof deck.Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are'field fabricated utilizing the approved membranes listed in Table 1.
One or more of the following:
Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft'
ENRGY 3,H-Shield,Polytherm-H,ACFoam-II,Polytherm,XtraFlex Polyiso
Minimum 1.5"thick 2 with 4;7 with 8;10 with 1:1.33 ft2
12
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Primer: Apply WB-3000 at 1 gal.per.300 sq.ft.
(Optional)
Base Sheet: One ply of Elastoflex SA V,Elastoflex SA V FR or Elastoflex SA V PLUS,Elastoflex SA V
PLUS FR,XtraFlex SBS Base SA,self-adhered.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR or Elastoflex SA V PLUS,
(Optional) Elastoflex SA V PLUS FR,XtraFlex SBS Base SA,self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA;Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -82.5 psf;(See General limitation#7.)
NOA No.:19-0311.04
Mu►MHDADe Courm .Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19/32'or greater plywood or wood plank,fastened at 24"spans with#8 wood screws at 6"o.c.
System Type D(1): All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
One or more layers of the following:
Base Insulation Laver Insulation Fasteners Fastener
able 3 Density/fe
Any approved Polyisocyanurate listed in Table 2
Minimum 1"thick N/A N/A
Ton Insulation Laver(Optional) Insulation Fasteners Fastener
able 3 Density/ft2
Fesco Board
Minimum'/a"thick N/A N/A
Structodek High Density Fiberboard Roof Insulation
Minimum%"thick N/A N/A
DensDeck,DensDeck Prime,SECUROCK Gypsum-Fiber Roof Board
Minimum 1/4"thick N/A N/A
Note: All insulation shall have preliminary attachment,prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft.,and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One ply of Elastobase,Elastobase P,Elastoshield HT,Polyanchor,XtraFlex SBS Glass Base
or XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using OMG#14 Roofgrip fasteners.and Flat Bottom Metal Plates,Dekfast
DF-#14-PH3 with Dekfast PLT-H-2-7/8 plates,Polygrip Fasteners#14 with Polygrip Hex
Plates or Trufast#14 HD Fasteners with Trufast 3"Metal Insulation Plates spaced 12"o.c.in a.
4"lap and 12"o.c.in two equally spaced staggered rows in the center of the sheet.
Ply-Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
NOA No.: 19-0311.04
MIAMI•DADE eoUN7Y Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP'S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf;(See General limitation#7.)
NOA No.: 19-0311.04
MAMWMDECOUNW Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: 19/32"or greater plywood or wood plank,fastened at 24"spans with#8 wood screws at 6"o.c.
.System Type D(2): All insulation is loosed.laid with preliminary attachment.to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck..Membranes subsequently adhered.
All General and System Limitations-apply.
One or more layers of the following:
Base Insulation Laver Insulation Fastener_s Fastener
able 3 Density/W
Any approved Polyisocyanurate listed in Table 2
Minimum 1"thick N/A N/A
Ton Insulation Laver(Optional) Insulation Fasteners Fastener
able 3 Density/W
Fesco Board
Minimum'/"thick N/A N/A
Structodek High Density Fiberboard Roof Insulation
Minimum%"thick N/A N/A
DensDeck,DensDeck Prime,SECUROCK Gypsum-Fiber Roof Board .
Minimum 1/"thick N/A N/A
Note: All.insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two1asteners per board for insulation boards having no dimension greater than 4
ft.,and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One ply of Elastobase,Elastobase P,Elastoshield HT,Polyanchor XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using OMG#14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
O.C.in a 4"lap and 12"o.c.in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR,XtraFlex SBS Base SA,self -adhered.
NOA No.:19-0311.04
MAMI-oNoe COUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR;Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -60 psf;(See General limitation#7.)
NOA No.: 19-0311.04
Mwr�i•naoecour�n Expiration Date: 10/11/22
APPROVED Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32'or greater plywood or wood plank,fastened at 24"spans with 8d common nails at 4"o.c.
or#8 wood screws at 6"o.c.
System Type E(1); Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase,Elastobase P,.Elastoshield HT,Polyanchor,XtraFlex SBS Glass Base
or XtraFlex SBS HT Base 650 fastened to the deck as described below:
'Fastening: Attach base sheet using 11 ga.annular ring shank nails and 1-5/8"diameter tin caps spaced 8"
o.c.in a 4"lap and 8"o.c.in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self-adhered-
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P.Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA of XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf;(See General limitation#7.).
NOA No.:19-0311.04
Mu�r+tiDaoe cout�rr�r Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32"or greater plywood or wood plank,fastened at 24"spans with 8d ring shank nails at 6"
o.c.at edges and intermediate supports.
System Type E(2): Base sheet is mechanically attached to roof deck.Membranes subsequently adhered,
All General and System Limitations apply.
Base Sheet: One ply of Elastobase,Elastoshield HT,Polyglass APP Base,XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 sheet fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga.annular grooved shank and 1"diameter caps spaced 6"o.c.in a
3"lap and 6"o.c.in four equally spaced staggered center rows.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf,(See General Limitation#7)
NOA No.: 19-0311.04
r'LAMID DEcoutMtW Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32'or greater plywood or wood plank,fastened at 24"spans with 8d common nails at 4"o.c.
or#8 wood screws at 6"o.c
System Type E(3): Base sheet is mechanically attached to roof deck.Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase,Elastobase P,Elastoshield HT,Polyanchor,XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using OMG 914 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c.in a 4"lap and 12"o.c.in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP-SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,.XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf;(See General Limitation#7)
NOA No.:19-0311.04
Mu►r7i•oa�e coutJrY Expiration Date: 10/11/22
,...•
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32'or greater plywood or wood plank,fastened at 24"spans with 8d common nails at 4"o.c.
or#8 wood screws at 6"o.c.
System Type E(4): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase,Elastobase P,Elastoshield HT,XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to thedeck as described below:
Fastening: Attach base sheet using 11 ga.annular ring shank nails and 1-5/8"diameter tin caps spaced 8"
o.c.in a 4"lap and 8"o.c.in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self-adhered.-
Membrane:
elf-adhered:Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: 'Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -52.5 psf;(See General Limitation#7)
NOA No.: 19-0311.04
MIAMM ADBCouNTY Expiration Dater 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated
Deck Description: _19/32"or greater plywood or wood plank,fastened at 24"spans with#8 wood screws at 6"o.c.
System Type E(5):. Base sheet is mechanically attached to roof deck.Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase,Elastoshield HT,Polyglass,APP Base,XtraFlex SBS Glass Base or
XtraFlex SBS HT Base 650 sheet fastened to the deck as described below:
Fastening: Attach base sheet using OMG#14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
DF-#14-PH3 with Dekfast PLT-H-2-7/8,Polygrip Fasteners#14 with Polygrip Hex Plates or
Trufast#14 HD Fasteners with Trufast 3"Metal Insulation Plates spaced 12"o.c.in a 4"lap
and 12"o.c.in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR;Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyrefleet,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification_
Maximum Design
Pressure: -60 psf;(See General,limitation V.).
NOA No.: 19-0311.04
MW41-DaaoeeournY Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32'or greater plywood or wood plank,fastened to supports spaced 24"o.c.and to blocking
members spaced 48"o.c.with TruFast TP#10x2-7/8"screws spaced 6"o.c.
System Type E(6): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase,Elastobase P,Elastoshield HT,XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 12 ga.annular ring shank nails and 1-5/8"diameter tin caps spaced 4"
o.c.in a 4"lap and 4"o.c.in four equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one ofthe approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design
Pressure: -97.5 psf,(See General Limitation#7)
NOA No.: 19-0311.04
MIAMI DADE COUNTY Expiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32'or-greater plywood or wood plank,fastened to supports spaced 24"o.c.and to blocking
members spaced 48"o.c.with#10x3"wood screws spaced 6"o.c.
System Type E(7): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase,Elastobase P,Elastoshield HT,XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to'the deck as described below:
Fastening: Attach base sheet using 12 ga.ring shank nails and tin caps spaced 4"o.c.in a 4"lap and 4"
o.c.in four equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR or Xtra.Flex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA FFR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA or XtraFlex SBS G SA
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design' -97.5 psf;With Elastoflex SA V or Elastoflex SA V FR(See General limitation V.)
Pressure: -112.5 psf;With all other base sheet options(See General limitation V.)
NOA No.: 19-0311.04
MIAMI DAD,COExpiration Date: 10/11/22
Approval Date:03/21/19
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32'or greater plywood or wood plank,fastened to supports spaced 24"o.c.with#80"wood
screws spaced 6"o.c.
System Type E(8): Base sheet is mechanically attached to roof deck.Membranes subsequently adhered.
All General and System Limitations apply.
Base Sheet: One ply of Elastobase,Elastobase P;Elastoshield HT,XtraFlex SBS Glass Base or XtraFlex
SBS HT Base 650 fastened to the deck as described below:
Fastening: Attach base sheet using 12 ga.annular ring shanked nails and 1-5/8"tin-caps 6"o.c.in 4"lap
and 6"o.c.in four equally spaced staggered rows. Tin-caps are primed with PG 100 or
XtraFlex 10.
Ply Sheet: One or more plies-of Elastoflex SA V,Elastoflex SA V FR,Elastoflex SA V PLUS,Elastoflex
SA V PLUS FR or XtraFlex SBS Base SA self-adhered.
Membrane: One ply of Elastoflex SA P,Elastoflex SA P FR,Polyflex SA P,Polyflex SA P FR,Polyfresko
G APP SA,Polyfresko G APP SA FR,Polyfresko G SBS SA,Polyfresko G SBS SA FR,
PolyKool,Polyreflect,XtraFlex APP G SA,XtraFlex Kool APP S SA,XtraFlex SBS G SA,
self-adhered.
Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or
(Optional) required fire classification.
Maximum Design -97.5 psf;With Elastoflex SA V or Elastoflex SA V FR(See General limitation#7.)
Pressure: -112.5 psf;With all other base sheet options(See General limitation#7.)
NOA No.: 19-0311.04
MLAM14=E COUNTY Expiration Date: 10/11/22
� Approval Date:03/21/19
.7
WOOD DECK SYSTEM LIMITATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance;refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product
Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 20-40 lbs./sq.,or mechanically attached using the fastening pattern of the
top layer
3. All standard panel sizes are acceptable for mechanical-attachment. When applied in approved asphalt,panel size
shall be 4'x 4'maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam
insulations when the base sheet is fully mopped.If no recovery board is used the base sheet shall be applied using
spot mopping with approved asphalt, 12"diameter circles,24"o.c.;or strip mopped 8"ribbons in three rows;one
at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12'in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 121bs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of-45 psE
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force(F')value of 275 Ibf.,as
tested in compliance with Testing Application Standard TAS 105. If the fastener value,as field-tested,are below
275 lbf.insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment.of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required,as determined by the Building Oficial,a revised fastener
spacing,prepared,signed and sealed by a Florida registered Professional Engineer,-Registered Architect,or
Registered Roof Consultant maybe submitted. Said revised fastener spacing shall utilize the withdrawal
resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing
Application Standard RAS 117.
7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall.be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA,General Limitation'#9 will not be applicable.)
8. All attachment and sizing of perimeter nailers,metal profile,and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones(i.e.field,
perimeters,and corners).Neither rational analysis,nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones(i.e.perimeters,extended comers and corners).(When this limitation is specifically
referred within this NOA,General Limitation#7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 19-0311.04
MIAMMADE COUNTY Expiration Date: 10/11/22
...1
Approval Date:03/21/19