HomeMy WebLinkAboutProduct Approvals • •. e - • • Fabricators,.LLC.,
2160 SW Poma Drive
Palm City, FL 34990
� � 772 X72-8034
Compliant with Florida Building Code 2017 (61h ed.) �� Fo
Compliant with Florida Product Approval Rule #61G20-39pe"m� Jl0
Compliant: Keystone Certifications sF �ng ID 49
i
Product: 1" Nailstrip 26GA Steel Roof Panel FBC Sec. 1507.4.2
Yield strength: 50 ksi min.; Attached to min. 15/32" plywood or
Wood Deck w/0.42 specific gravity with 16",Coverage (Max.) ?-j&O
Rib Height 1 REVIEWED FOR
Corrosion Resistant Compliant: FBC Sec. 1507.4.3 i
CO® ICE
Fastener 1:.#10-x 1" (min.) Pancake Head Wood Screw to penrf"� I %'Nu rbottom of support. T
Adhesive/Sealant : Bostik 91STm Chem-Chalk one component, polyuretWeRghesive with
3/16" continuous bead application along base of male 'rib vertical flange at each pan
seam.
Underlayment: To be compliant with FBC Sec 1507.1.1File C®
pY
Slope: Shall be in compliance with FBC Sec. 1507.
Install,Details:,aTable{A� Allowable Loads METHOD 1 METHOD 2
DESIGN PRESSURE* -86 PSF Main field -97.25 PSF Perimeter
FASTENER'SPACING 6"O.C. 6" O.C.
SEAM ADHESIVE Not required 3/16"continuous bead
s).r
Reference Data: ARCHITECTURAL TESTING, INC.TST ID#: 1527
UL 580-06 &UL 1897-04 TEST REPORT D8133.01-450-18 06/30/15 Specimen#1&-#2
.EQUIVALENCY:UL1897-04 is equivalent to Test Standard UL1897-12. J *Design.Pressure mar in:.of safe 2:1
Certificate of Independence:
Locke Bowden,P.E.does not have,not will acquire a financial ilopnastai 09y,company manufacturing or distributing products
under this evaluation. �����
Locke Bowden,P.E.is not owned,operated,or controll ymR� +d anulocturer,or distributing products under this
report.
0 00-*�
.' •
•
12
' '� • seal
��•� STATE OF t� t
Alli. 6a
°'-fs'ONAL E
Limitations:
1.Underlayment to be compliance with current Florida Building Code(FBC)21017 6t'ed.:
2.Minimum slope to be compliant with Florida Building Code 2017 6"'ed.,and per with Manufacturer's installation reference.
3.Products are compliant for State of Florida product approval per Rule 61 G20-3.Compliance Method: 1-D
-4.Engineering analysis for"project specific approval by local authorities wrurisdiction is allowed by other registered engineers.
5.Fire classification is not part of this acceptance.Shear diaphragm values are outside this report.
6.Support framing in compliance w/FBC 2017 6"'ed.,.Chapter 22 for Steel,Chapter 23 for Wood and Chapter 16 for Structural
ti Loading.
7.This report does not imply warranty,installation,recommended product use outside of this report.
FL 17022.5 1.0 Nail Strip (26GA Steel), 16"Wide Roof Panel -Details
16"
1"
�—
3/411 —
Panel Profile
16" o.c.
Deck:
-15/32"or greater Plywood,or
-Wood plank
Integral Snap Lock
For METHOD 2:
Apply 3/16"Bead-Bostik 915Tm Sealant
Continuous Along Male Rib Vertical Flange
;Fastener
#10 X 1"Min. per Table"A"
Pancake Head Wood Screw
(Typical Fastening Pattern AcroI ss Width)
i
FL 17022.5 1.0 Nail Strip (26GA Steel), 1671 Wide Roof Panel -Details
I
i
Fastener
#10 x 1"Min. per Table"A"
Pancake Head Wood Screw
1"Nail Strip Roof Panel
Jr
YY
�f
I Y
`•'d`.rS��':'. - ,fy _ f ,. i? .1S�` Ls�"�;t•. . \�-v U�"'%y��.`—Y.'/�.t � `!L, -
Seam Adhesive Application:
Deck: For Method 2
15/32"or greater Plywood, or Apply 3116"Bead Bostik 915Tm Sealant
-Wood plank Continuous Along Male Rib Vertical Flange
(Refer to Table"A")
Isometric View.
I
MIAMI-RADE
MIAMI-DARE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES f tER) 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION ~i�j! O Miami,Florida 33175-2474
T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.aov/economy
VIEWED O R
Polyglass USA Inc. _„R
1111 W.Newport Center Drive CODE COMPLIANCE
IANCE
Deerfield Beach,FL 33442 ST. L U C I E COUNTY
SCOPE: BOCO
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control Section I
(in Miami-Dade County)and/or the AHJ(in areas other than Miami-Dade County)reserve the right to have this
product or material tested for quality assurance purposes.If this product or material fails to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein,and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Polystick Underlayments File Copy
LABELING:Each unit shall bear a permanent label with the manufacturer's name or logo,city,state and following,
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,i
for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then
it shall be done in its entirety.
I
INSPECTION:A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA No.15-0410.04 and consists of pages 1 through 8.
The submitted documentation was reviewed by Freddy Semino.
,.,_
�/11/2
MIAMMAD,COUNTY Expiration Date: 0
Page 1 of 8
i
f
! I it
i
I
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub-Category: Underlayment
Material: SBS,APP Self-Adhering Modified Bitumen
PRODUCTS DESCRIPTION:
Test Product
Product Dimensions Specification Description
Polystick IR-Xe 65'x 3'3_3/8" ASTM D 1970 A fine granular/sand top surface self-adhering,APP
Manufacturing Or 65'x 3' polymer modified,fiberglass reinforced,bituminous
Location#1  60 mils thick sheet material for use as an underlayment in sloped roof
assemblies: Designed as an ice&rain shield.
Polystick Dual Pro 61'x 333/8" TAS 103 and A rubberized asphalt self-adhering,glass-fiber/polyester
Manufacturing 60 mils thick ASTM D 1970 reinforced waterproofing membrane. Designed as a i
Location#2 metal roofing and roof tile underlayment.
Polystick Tile Pro 61'x 3'33/8" TAS 103 and A rubberized asphalt self-adhering,glass-fiber/polyester
Manufacturing 60 mils thick ASTM D 1970 reinforced'waterproofing membrane.Designed as a metal
Location#2 roofing and roof tile underlayment.
Polystick TU Max 65'8"x 3'3-3/8" TAS 103 and A rubberized asphalt self-adhering,polyester reinforced
Manufacturing 60 mils thick ASTM D 1970 waterproofing membrane. Designed as a a roof tile
Location#1  underlayment.
Polystick TU P 32'10"x 3'3-%" TAS 103 and A rubberized asphalt waterproofing membrane,glass-
Manufacturing 130 mils thick ASTM D 1970 fiber/polyester reinforced,with a granular surface
Location#2 designed for use as a tile roof underlayment.
Polystick TU Plus 65'x 3'33/8" TAS 103 and A rubberized asphalt self-adhering,glass-fiber/polyester
(Surface Printing) 80 mils thick ASTM D 1970 reinforced waterproofing membrane.Designed as a metal
Manufacturing roofing and roof file underlayment.
Location#1 
Polystick MTS 65'8"x 3'33/8" TAS 103 A homogeneous,rubberized asphalt waterproofing
Manufacturing 60 mils thick membrane,glass fiber reinforced with polyolefinic film
Location#2 on the upper surface for use as an underlayment for metal
roofing,roof tile,slate tiles and shingle underlayment.
Polystick MTS Plus 65'8"x 333/8" TAS 103 A homogeneous,rubberized asphalt waterproofing
Manufacturing 60 mils thick membrane,glass fiber reinforced with polyolefinic film
Location#2 on the upper surface for use as an underlayment for metal
roofing,roof tile,slate tiles and shingle underlayment.
Elastoflex S6 G 32'10"x 3'33/e" TAS 103 and Polyester reinforced, SBS modified bitumen membrane
Manufacturing ASTM D 6164 with a sanded back face and a granule top surface. For
Location#2 use in roof tile underlayment systems.
NOA No.: 17-0614.22
MIAMFDAD;COUNTY Expiration Date: 09/13/21
Approval Date: 07/06/17
Page 2 of 8
I
i
I
I
i
I
MANUFACTURING PLANTS:
1. Hazelton,PA
2. Winter Haven,FL
EVIDENCE SUBMITTED
Test Agency Test Identifier Test Name/Report Date
Trinity ERD P10870.09.08-R1 TAS 103 12/04/08
P10870.04.09 TAS 103/ASTM D4798&G155 04/13/09
P33360.06.10 ASTM D1970 07/01/10
P33370.03.11 TAS 103 03/02/11
P33370.04.11 ASTM D 1623 04/26/11
P36900.09.11 TAS 103/ASTM D4798&G155 09/01/11
P37300.10.11 TAS 110/ASTM D4798&D1970 10/19/11
P40390.08.12-2 ASTM D 1623 08/07/12
P37590.07.13-1 ! ASTM D6164 07/02/13
P45270.05.14 TAS 103;TAS 110&ASTM D1623 05/12/14
P46520.10.14 ASTM D1623 10/03/14
P44360.10.14 TAS 103 &TAS 110 10/07/14
P43290.10.14 ASTM D 1970&TAS 110 10/17/14
PLYG-SC10130.06.16-3 TAS 103 &TAS 110 06/27/16
PLYG-10130.06.16-1 ASTM D1970&TAS 110 06/27/16
PRI Asphalt Technologies PUSA-035-02-01 TAS 103 09/29/06
PUSA-055-02-02 i
i TAS 103 12/10/07
PUSA-089-02-01 TAS 103/ASTM D4798&G155 07/06/09
Momentum Technologies,Inc. JX20H7A TAS 103/ASTM D4798&G155 04/01/08
RX14E8A TAS 103/ASTM D4798&G155 11/09/09
DX23D8B TAS 103/ASTM D4798&G155 02/18/10
DX23D8A TAS 103/ASTM D4798&G155 02/18/10
LABELING:
1. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo,city
and state of manufacturing facility and the following statement: "Miami-Dade County Product Control Approved"
or the Miami-Dade County Product Control Seal as shown below.
MIAMI•DADE COUNTY
BUILDING PERMIT REQUIREMENTS:
Application for building permit shall be accompanied by copies of the following:
1.This Notice of Acceptance.
2.Any other documents required by the Building Official or applicable building code in order to properly evaluate the
installation of this materials.
NOA No.: 17-0614.22
MIAMEDADE couNrY Expiration Date: 09/13/21
Approval Date: 07/06/17
Page 3 of 8
i
I
i
INSTALLATION PROCEDURES:
Deck Type 1: Wood,non-insulated
Deck Description: Min. 19/32"plywood or wood plank
System Type E(1): Anchor sheet mechanically fastened to deck,membrane adhered
Anchor/Base Sheet: One or more plies of ASTM D 226 Type ll or ASTM D 2626.
Fastening: Per FBC 1518.2& 1518.4 Nails and tin caps 12"grid,6"o.c.at a minimum 4"head lap.(for
base sheet only)
i
Membrane: Polystick IR-Xe,Polystick Dual Pro,Polystick Tile Pro,Polystick TU Max,Polystick
TU P,Polystick TU Plus,Polystick MTS or Polystick MTS Plus,self-adhered.
Surfacing: See General Limitations Below.
I
Deck Type 1: Wood,non-insulated
Deck Description: Min. 19/32"plywood or wood plank
System Type E(2): Anchor sheet mechanically fastened to deck,membrane adhered
Anchor/Base Sheet: One or more plies of ASTM D 226 Type H or ASTM 02626.
Fastening: Per FBC 1518.2& 1518.4 Nails and tin caps 12"grid,6"o.c.at a minimum 4"head lap. or
base sheet only)
Membrane: Elastoflex S6 G,hot asphalt applied
Surfacing: See General Limitations Below.
i
Deck Type 1: Wood,non-insulated
Deck Description: Min. 19/32"plywood or wood plank
System Type E(3): Base sheet mechanically fastened to deck, subsequent cap membrane self-adhered.
Anchor/Base Sheet: One or more plies of ASTM D 226 Type ll or ASTM D 2626.
Fastening: Per FBC 1518.2& 1518.4 Nails and tin caps 12"grid,6"o.c.at a minimum 4"head lap.(fol
base sheet only)
Ply Sheet: Polystick MTS Plus,self-adhered with minimum 3"horizontal laps and minimum 6"
vertical laps.
Membrane: Polystick TU Plus,self-adhered.
Surfacing: See General Limitations Below.
NOA No.: 17-0614:22
Miar�I•DEwe courirr Expiration Date: 09/13%21
Approval Date: 07/06/17
Page 4 of 8
I
INSTALLATION REQmEMENTS:
1. All nails in the deck shall be carefully checked for protruding heads. Re-fasten any loose deck panels,and
sweep the deck thoroughly to re move any dust and debris prior to application.
2. Place the underlayment over metal drip edge in accordance with RAS 111.
3. Place the first course of membrane parallel to the eave,rolling the membrane to obtain maximum contact.
Remove the release film as the membrane is applied. All side lap's shall be a minimum of 3"and end laps shall
be a minimum of 6". Roll the membrane into place after removing the release strip. Vertical strapping of the
roof with Polystick is acceptable. Membrane shall be back nailed,in accordance with applicable building code.
4. When applying the membrane in the valley,start at the low point and work to the high point,rolling the
membrane from the center outward in both directions.
5. For ridge applications,center the membrane and roll from the center outward in both directions.
6. Roll or broom the entire membrane surface so as to have full contact with the surface,giving special attention
to lap areas.
7. Flash vent pipes,stacks,chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance.
8. All protrusions or drains shall be initially taped with a 6"piece of underlayment. The flashing tape shall be
pressed in place and formed around the protrusion to ensure a tight fit. A second layer of Polystick shall be
applied over the underlayment.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance.
2. Polystick Dual Pro,Polystick Tile Pro,Polystick TU Plus,Polystick MTS and Polystick MTS Plus may be
used in asphaltic shingles,wood shakes and shingles,non-structural metal roofing,roof tile systems and quarry
slate roof assemblies.
Polystick TU P may be used in all the previous assemblies listed except metal roofing.
Polystick IR-Xe may be used in all the previous assemblies listed except metal roofing and roof tile systems.
Polystick TU Max may be used in non-structural metal roofing and roof rile systems.
Elastoflex S6 G may be used in roof tile systems only.
3. Deck requirements shall be in compliance with applicable building code.
4. Polystick IR-Xe,Polystick Dual Pro,Polystick Tile Pro,Polystick TU Max,Polystick TU P,Polystick TU
Plus,Polystick MTS and Polystick MTS Plus shall be applied td a smooth,clean and dry surface. The deck
shall be free of irregularities.
5. Polystick IR-Xe,Polystick Dual Pro,Polystick Tile Pro,Polystick TU Max,Polystick TU P,Polystick TU
Plus,Polystick MTS and Polystick MTS Plus shall not be adhered directly over a pre-existing roof membrane
as a recover system.
6. Polystick IR-Xe,Polystick Dual Pro,Polystick Tile Pro,Polystick TU Max,Polystick TU P,Polystick TU
Plus,Polystick MTS and Polystick MTS Plus shall not be left exposed as a temporary roof for longer than the
amount of days listed in the table below after application. Polyglass reserves the right to revise or alter product
exposure times;not to exceed the preceeding maximum time limitations.
Exposure Limitations(Days)
MTS IR-Xe Elastoflex TU TU P Tile Pro Dual Pro TU Max MTS Plus
S6 G Plus
Winter Haven,FL 180 90 180 180 180 180 180 180 180
Hazelton,PA N/A 90 N/A 180 N/A N/A N/A 180 N/A
7. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
NOA No.: 17-0614�22
MIAMFDAD;COUNTY Expiration Date: 09/13/21
Approval Date: 07/06%17
Page 5 o� 8
I
I
Rule 61G20-3 of the Florida Administrative Code.
8. In roof rile application,data for the attachment resistance of roof tiles shall be as set forth in the roof file
manufacturer's Notice of Acceptance.
Polystick Tile Pro,Polystick TU Max,Polystick TU Plus or Elastoflex S6 G may be used in both adhesive
set and mechanically fastened roof file applications.
Polystick Dual Pro is limited to mechanically fastened roof tile applications.
Polystick MTS and Polystick MTS Plus are limited to mechanically fastened with the limitations outlined in
Section 9.
Polystick TU P may be used in mechanically fastened roof tile applications with the exception of mortar set tile
applications.
9. When loading roof tiles on roof tile underlayment for(direct-to-deck)rile assemblies,the maximum roof slope
shall be as follows: (See Table Below)
Tile Polystick Elastoflex Polystick TU Plus, Polystick Polystick System(E3)
Profile MTS S6 G TU P,Tile Pro, TU Max MTS Plus MTS Plus with
Dual Pro TU Plus
Flat Tile Prohibited 4:12 6:12 6:12 5:12 6:12
without battens I L
Profiled Prohibited 4:12 6:12 6:12 4:12 6:12
Tile without battens
The above slope limitations can be exceeded only by using battens�in accordance with the Approved Tile System
Notice of Acceptance and applicable Florida Building Code requirements. When battens are required,they shall
be utilized during loading and installation of tiles.
10. Care should be taken during the loading procedure to keep foot traffic to a minimum and to avoid dropping of
tile directly on the underlayment.Refer to Polyglass'Tile loading detail below for loading procedure—two tiles
laid perpendicular to slope followed by a maximum four tile stack parallel to the slope,for a total of 6 tiles—for
all underlayments except Polystick MTS which shall be loaded onto battens.
I
ME
I
M MMFDADE COUNTY NOA No.: 17-0614.22
Expiration Date: 09/13/21
Approval Date: 07/06/17
Page 6 of 8
i
i
I
11. Refer to prepared roofing system Product Control Notice of Acceptance for listed approval of this product with
specific prepared roofing products. Polystick IR-Xe,Polystick Dual Pro,Polystick Tile Pro,Polystick TU
Max,Polystick TU P,Polystick TU Plus,Polystick MTS,Polystick MTS Plus or Elastoflex S6 G may be
used with any approved roof covering Notice of Acceptance listing Polystick IR-Xe,Polystick Dual Pro,
Polystick Tile Pro,Polystick TU Max,Polystick TU P,Polystick TU Plus,Polystick MTS,Polystick MTS
Plus or Elastoflex S6 G as a component part of an assembly in the Notice of Acceptance.
If Polystick IR-Xe,Polystick Dual Pro,Polystick Tile Pro,Polystick TU Max,Polystick TU P,Polystick
TU Plus,Polystick MTS,Polystick MTS Plus or Elastoflex S6 G are not listed,a request may be made to the
Authority Having Jurisdiction(AHJ)or the Miami-Dade County Product Control Section for approval provided
that appropriate documentation is provided to detail compatibility'of the products,wind uplift resistance,and Are
testing results.
POLYGLASS GENERAL APPLICATION GUIDELINE&FOR POLYSTICK MEMBRANES
PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LEVIITATIONS OF SPECIFIC APPLICATIONS.
LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS.
1. Polyglass does accept the direct application of Polystick underlayment membranes to wood decks. Installers are
cautioned to refer to applicable local building codes prior to direct deck installation to ensure this is acceptablel.
Please also refer to applicable Product Data Sheets of the corresponding products.
2. All rolls,with the exception of Polystick TU Plus should be back-nailed in selvage edge seam as per Polyglass
Back Nailing Guide. Nails shall be, 11 gauge ring shank type,applied with a minimum 1 %"metal disk as
required in Miami-Dade County or simplex type nail as otherwise allowable in other regions,at a minimum rate
of 12"o.c. Polystick TU Plus should be back nailed in designated'area marked"nail area,area para clavar"on
the face of membrane,with the above stated nails and/or disks.The head lap membrane is to cover the area being
back-nailed. (Please refer to applicable local building codes prior to installation.)
3. All seal lap seams(selvage laps)must be rolled with a hand roller to ensure full contact.
4. All fabric over fabric;and granule over granule end laps,shall have a 6"wide,uniform layer of Polyglass
I
Polyplus 55 Premium Modified Flashing Cement,Polyglass Polyplus 50 Premium MB Flashing Cement,
XtraFlex 50 Premium Modified Wet/Dry Cement,Polyglass PG500 MB Flashing Cement,applied in between
the application of the lap.The use of mastic between the laps does-not apply to Polystick MTS.
5. A maximum of 6 tiles per stack are allowed when loading tile on the underlayments.Refer to the Polyglass Tile
Loading Guidelines. See General Limitations#9 and#10.
6. Battens and/or Counter-battens,as required by the tile manufacturers NOA,must be used on all projects for
pitch/slopes of 7712"or greater. It is suggested that on pitch/slopes in excess of 6 %a"/12",precautions should be
taken,such as the use of battens to prevent file sliding during the loading process.
7. Minimum cure time after membrane installation&before loading of roofing tiles is Forty-Eight(48)Hours.
8. Polystick membranes may not be used in any exposed application such as crickets,exposed valleys,or exposed!
roof to wall details.
9. Repair of Polystick membranes is to be accomplished by applying Polyglass Polyplus 55 Premium Modified
Flashing Cement,Polyglass Polyplus 50 Premium MB Flashing Cement,XtraFlex 50 Premium Modified
Wet/Dry Cement,Polyglass PG500 MB Flashing Cement to the area in need of repair,followed by a patch of the
Polystick material of like kind should be set and hand rolled in place over the area needing such repair.Patching
membrane shall be a minimum of 6 inches in either direction. The repair should be installed in such a way so
that water will run parallel to or over the top of all laps of the patch.
NOA No.: 17-0614.22
MIAMFDAD;COUNTY Expiration Date: 09/13121
Approval Date: 07/06/17
Page 7 of 8
II
i
10. All self-adhered membranes must be rolled to ensure full contact with approved substrates. Polyglass requires a
minimum of 40 lbs for a weighted roller for the rolling of the field membrane. Hand rollers are acceptable for
rolling of patches or small areas of the roof. Brooming may be used where slope prohibits rolling.
11. All approved substrates should be dry,clean and properly prepared,before any application of Polystick
membranes commences. An approved substrate technical bulletin can be furnished upon request.It is
recommended to refer to applicable building codes prior to installation to verify acceptable substrates.
12. The Polyglass Miami-Dade Notice of Acceptance(NOA)approval for Polystick membranes can be furnished
upon request by our Technical Services Department by calling 1 (800)894-4563.
13. Questions in regards to the application of Polyglass products should be directed to our Technical Services
Department at 1 (800)894-4563.
14. Polyglass recommends that applicators follow good roofing practices and applicable procedures as outlined by
the National Roofing Contractors Association(NBCA).
PLEASE CHECK WITH LOCAL BUILDING CODES REGARDING LIMITATIONS OF SPECIFIC APPLICATIONS.
LOCAL CODES MAY SUPERSEDE POLYGLASS REQUIREMENTS AND RECOMMENDATIONS.
END OF THIS ACCEPTANCE
NOA No.: 17-0614.22
CMILAMMADECOUNTY Expiration Date: 09/14.21
Approval Date: 07/06/17
Page 8 of 8
MIAMIOWDE EVIEWE® FOR
C�+ C�+ -DADE COUNTY
®®E OMP We TROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(ItE �p �'E ®��1d�W 26 Sheet,Room 208
BOARD AND CODE ADMINISTRATION DIVISION 6J. '� Florida 33 1�75-2474
B®CC T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.aov/economy
• I
Extreme Metal Fabricators,LLC
2160 Poma Drive
Palm City,FL 34990
SCOPE: File Copy
'This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section
(in Miami-Dade County)and/or the AHJ (in areas other than Miami-Dade County)reserve.the right to have this product
or material tested for quality assurance purposes.If this product or material fails to perform in the accepted manner,the
manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or suspend the se
of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is
determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements
of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: DMC 150SS-24GA Steel Panel over Plywood deck
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo,city,state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision.or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official:
This NOA consists of pages 1 through 11.
The submitted documentation was reviewed by Gaspar J Rodriguez.
r �
;tla III
NOA No.: 15-0309.04
CMtAMMADEcouNnr Expiration Date: 09/17/20 .
Approval Date:09/17/15
Page 1 of 11
j
i
ROOFING SYSTEM APPROVAL:
Category: Roofing
Sub-Category: Metal,Panels(Non-Structural)
Material: Steel
Deck Type: Wood
Maximum Design Pressure: -165 PSF j
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
Test I Product
Product Dimensions Specifications Description
i
DMC 150 SS—24GA Length:various TAS 110 ' Corrosion resistant,galvanized steel or
Steel Panel -Height: 1-1/2" galvalume standing seam metal panel.
Width: 16"
Thickness 24 GA
Min.Yield Strength: 50KSI
DMC 150SS Butterfly Base Two piece panel clip(base and upper clip)
Clip Length:4.5" used for the field conditions of DMC 150
Height: 1-1/4" i SS panel assembly System A.
Width: l"
Thickness:22GA
Upper Clip
Length: 5.045"
Height: 0.929" j
Width: 0.40"
Thickness:24GA
DMC 150SS Base Two piece panel clip(base and upper clip)
Continuous Butterfly Length: 120" used for the perimeter and corner
conditions of DMC 150 SS panel assembly
Clip Height: 1-1/4"
Width: 1" System A.
Thickness:22ga
Upper Clip
Length: 5.045"
Height: 0.929"
Width:0.40"
Thickness:24GA
24 GA DMC 150SS Length:2-1/4" - ; One piece panel clip used for the field
Fixed Clip Height: 1-5/8" i conditions of DMC 150 SS panel assembly
Base Width: 15/16" System B.
Thickness:24GA
22 GA DMC 150SS Length:6-1/4" One piece panel clip used for the perimeter
Fixed Clip Height: 1-5/8" and corner conditions of DMC 150 SSS
Base Width:3/4" panel assembly System B.
Thickness:22GA
Bostik 70-05A N/A TAS 110 1 Heavy duty construction adhesive.
i
NOA No.: 15-0309.04
rtwMi•nae eouNrtt Expiration Date:09/17/20
j Approval Date:09/17/15
Page 2 of 11-
I
i
EVIDENCE SUBMITTED:
Test Agency Test Identifier j Test Name/Renort Date
Akzo Nobel Coatings,Inc. Lab Form ASTM G 153
PRI Asphalt Technologies,Inc. AKZC-001-02-01 ASTM B 117 - 10/08/02
AKZC-001-02-02
AKZC-001-02-03
AKZC-001-02-04
AKZC-001-02-05
i
DMC-006-02-01 TAS 125 03/11/113
DMC-009-02-01 TAS 100 03/11/13
Architectural Testing. 56842.02-122-18 ! TAS 100 06/08/05
Hurricane Test Laboratory,Inc. 0287-0311-07 TAS 125 08/07/07
i
f
NOA No.: 15-0309.04
Mwr�tinan�couNrir Expiration Date: 09%17/20
Approval Date:09/17/15
Page 1 of 11
I
I
i
I
APPROVED ASSEMBLIES:
System A:, DMC 150 SS—24GA Steel Panel 16"wide Panel
Deck Type: Wood,Non-insulated
Deck Description: New Construction 19/32"or greater plywood'or wood plank.
Slope Range: 2": 12" or greater
Maximum Uplift See Maximum Design Pressures below !
Pressure:
Deck Attachment: In accordance with applicable Building Code,but in no case shall it be less than 8d annular
ring shank nails spaced 6"o.c. In reroofing,'where the deck is less than 19/32"thick
(Minimum 15/32")the above-attachment method must be in addition to existing attachment.
Underlayment: Minimum underlayment shall be an ASTM D 226 Type II installed with a minimum 4"
side-lap and 6"end.-laps. Underlayment shall be fastened with corrosion resistant tin-caps
and 12 gauge 1 1/4"annular ring-shank nails,;spaced 6"o.c. at all laps and two staggered
rows 12"o.c.in the-field of the roll or any approved underlayment having a current N A.
Fire Barrier Board: Any approved fire barrier having a current NOA. Refer to a current fire directory listing for
fire ratings of this roofing system assembly as well as the location of the fire barrier within
the assembly. See Limitation# 1.
Valleys: Valley construction shall be in compliance with Roofing Application Standard RAS 133
and with the current published installation instructions and details in DMC Association of
Regional Manufacturers Installation Manual'.
Metal Panels and Install the"DMC 150 SS—24GA Steel Panel 16"wide Panel'including flashing
Accessories: penetrations,valleys, end laps and accessories in compliance with"DMC Association of
Regional Manufacturers"current published installation instructions and in compliancewith
the minimum requirements detailed in Roofing Application Standard RAS 133.
Field Conditions: Panels shall be secured along the male rib with approved clips fastened with two corrosion
resistant 410 pancake head fasteners of sufficient length to penetrate through the sheatliirig
a minimum of 3/16". The panel clips shall bei located at the maximum spacing listed in
Table A below.
i
TABLE A ,
MAXIMUM DESIGN PRESSURES
Roof Areas Field Perimeter and Corner'
Maximum Design Pressures -99.25 -114.25
Maximum Clip Spacing 16"OC 12" OC
Clip DMC 15OSS Butterfly Clip; DMC 15OSS Continuous Butteity
Clip
Mechanical Seam 1800 1800
1. Extrapolation shall not be allowed
i
i
NOA No.: 15-0309.04
htuuhi•oanE couNnr Expiration Date:09/17/20
Approval Date: 09/17/15
Page 41 f 11
I
i
i
System B: DMC 150 SS—24GA Steel Panel 16"wide Panel
Deck Type: Wood,Non-insulated
Deck Description: New Construction 19/32"or greater plywood or wood plank.
Slope Range: 2": 12" or greater
Maximum Uplift See Table B below
Pressure:
Deck Attachment: In accordance with applicable Building Code,but in no case shall it be less than 8d annular
ring shank nails spaced at a maximum distance specified below in Table B. In reroofing,
where the deck is less than 19/32"thick(Minimum 15/32")the above attachment method must
be in addition to existing attachment.
Underlayment: Minimum underlayment shall be an ASTM D 226 Type.II installed with a minimum 411
side-lap and 6"end-laps. Underlayment shall be fastened with corrosion resistant tin-caps
and 12 gauge 1 1/4"annular ring-shank nails,spaced 6"o.c. at all laps and two staggered
rows 12"o.c.in the field of the roll or any approved underlayment having a current NOA.
Fire Barrier Board: Any approved fire barrier having a current NOA. Refer to a current fire directory listi ng for
fire ratings of this roofing system assembly as well as the location of the fire barrier within
the assembly. See Limitation# 1.
Valleys: Valley construction shall be in compliance with Roofing Application Standard RAS 133
and with the current published installation instructions and details in DMC Association' 'of
Regional Manufacturers Installation Manual:
Metal Panels and Install the"DMC 150 SS—24GA Steel.Pane1 16"wide Panel" including flashing
Accessories: penetrations,valleys, end laps and accessories in compliance with"DMC Association of .
Regional Manufacturers"current published installation instructions and in coinpliance.with
the minimum requirements detailed in Roofing Application Standard RAS 133. .
Panels shall be secured along the male rib with approved Panel clip listed below in Table B
with two corrosion resistant#10 pancake head fasteners of sufficient length to penetrate
through the sheathing a minimum of 3/16". The panel clips are to be placed at a spacing .
listed below in Table B. The female rib of panel is placed over the male/clip assemblyl and
seamed.
TABLE B
MAXIMUM DESIGN PRESSURES
Roof Areas Field Perimeter and Cornerl Perimeter and Corner1
Option 1 Option 2
Maximum Design Pressures -90PSF -150PSF -165PSF
Plywood Fastener Spacing 6"OC 6"OC 4" OC
Clip Type 24 GA DMC 150SS 22 GA DMC 150SS Fixed 22 GA DMC 150SS Fixed
Fixed Clip clip Clip
Maximum Clip Spacing 16" OC 12"OC 8"OC
Bostik Seam Sealant None 1 1/4"bead None
Mechanical Seam 900 900 1800
1. Extrapolation shall not be allowed
I
NOA No.: 15-0309.04
MIAMI-DAnecoUNTY Expiration Date:09/17/20
Approval Date: 09/17/15
Page 5'of 11
� I
I
i
LIMITATIONS
I
1. Fire classification is not part of this acceptance;refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. The maximum designed pressure listed herein shall be applicable to all roof pressure zones.(i.e.field,perime ers,
and corners).Neither rational analysis,nor extrapolation shall be permitted for enhanced fastening at enhanced
pressure zones(i.e.perimeters,extended corners and corners).
3. Panels may be rolls formed in continuous lengths from eave to ridge.Maximum lengths shall be as described in
Roofing Application Standard RAS 133
4. All panels shall be permanently labeled with the manufacturer's name and/or logo, city and state, and the
following statement:."Miami-Dade County Product Control Approved" or with the Miami-Dade County Product
Control Seal as seen below. All clips shall be permanently labeled with the manufacturer's name and/or,logo,
and/or model.
MIAMI•DADE COUNTY
5. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
6. Panels may be jobsite roll formed with machine model#0290414; 3381213; 42.60215; 5960197; 10811107 from
DMC Association of Regional Manufacturers.
i
I
f
� I
� I
NOA No.: 15-03109.04
rtu►r�uM
unrnrExpiration Date: 09/17/20
Approval Date:09/ 7/15
Page 6 of 11
j
PROFILE DRAWINGS
16"
3/8"
I
i
DCM 150 SS-24GA STEEL PANEL
15/8"
42"
i� •r
DMC 150SS BUTTERFLY CLIP
I
i
I
I
NOA No.: 15-0309.04
m I-DAD.cO j Expiration Date:09/17/20
Approval Date:09/17/15
Page 7 of 11
i
- I
i
I
i
611
15/811
♦,
8
1
DMC 150SS CONTINUOUS BUTTERFLY CLIP
7to
L
-
% t 8
S _
^�-
1� ca -
f �
1.slt 2416
t
24 GA,DMC 150SS FIXED CLIP
it tr-- 5
3..
a
22 GA,DMC 150SS FIXED CLIP
NOA No.: 15-0309.04
MIAMI•DAD,COUNTY Expiration Date:09/17/20
Approval Date:09/17/15
Page.8 of 11
i
DETAIL A
16" ox.
(Field Conditions)
- O
I O e0
a
Oa
O a �
i
O a 12"o.c.
e
(Perimeter and Corner Conditions)
NOA No.: 15-0309.04
t�fuutI•naoe couNnr Expiration Date:09/17/20
Approval Date:09/17/15
Page 9 of 11
DETAIL A(CONT.)
DMC 15OSS PANEL-
DMC 15088 CLIP
(2)#10- 13 x 1" PHW
UNDERLAYMENT
SUBSTRATE--
(Seam
UBSTRATE--(Seam Detail System A—Field,Perimeter and Corner Condition)
i
DETAIL B
DMC 15OSS PANEL
DMC 150SS CLIP
(2)_ #10 - 13 x 1" PHW
UNDERLAYMENT
SUBSTRATE
(Field Condition Seam Detail)
I
NOA No.: 15-0309.04
MIAMI•DADEcOUNTY Expiration Date:09/17/20
Approval Date:09/17/15
Page 10,6f 11
i
DETAIL B (CONT.)j
1
CORNER ZONE SEAM ADHESIVE
• (IW BEAD BOSTIFK 70-05A)
DMC 15OSS PANEL
--
DMC 15OSS CLIP
(2) #10— 13 x 1" PHW
UNDERLAYMENT
SUBSTRATE
(Perimeter and Corner Condition—Option 1 Seam Detail)
I
i
DMC 1508S PANEL—
DMC
ANEL
DMC 150SS CLIP
(2) #10- 13 x 1" PHIV -----
UNDERLAYMENT
SUBSTRATE
- c
a i
(Perimeter and Corner Condition—Option 2 Seam Detail)
END OF THIS ACCEPTANCE
NOA No.:15-0309.04
MIAM4CIADE COUNTY
• Expiration Date:09/17/20
Approval Date:09/17/15
Page 11 of 11
C � �