HomeMy WebLinkAboutProduct Approval L
w11+l4ifwlwOt4p1'e OP V
MIAMI-BADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami,Florida 33175-2474
T(786)315-2590 F(786)315-2599
-NOTICE OF ACCEPTANCE (NOA) www.miamidadc govhconomv
Polyglass USA,Inc.
150 Lyon Drive
Fernley,NV 89408
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control Section
(In Miami Dade County)and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this
product or material tested for quality assurance purposes.If this product or material fails to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code. ,
This product is approved as desc fficd.herein,.and has been designed to comply with.the Florida Building Code
includin the Hi - e oV Hurricane Zone of the Floridaalwltiirrg E
DES RIPTION:Polyglass Self-Adhered Roof System over Wood Decks
LABEL i shall bear a ermanent Labe acturer's nam or logo,city,state and following
statement:"Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,
for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section .
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County,Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it shall be done
in its entirety.
INSPECTION:A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA# 13-1217.41 and consists of pages 1 through 34.
The submitted documentation was reviewed by Alex Tigera.
Ae Copy
MIAMMA CQWTM RE. 10YED FOR NOA No.: 17-1004.09
• \ Expiration Date: 10/11/22
0E COMPLIANCEipproval Date:10/12/17
T. L CIE COU .y Page i of 34
B0CG4M(_aZ6
r
ROOFPIG ASSEMBLY APPROVAL
Cateeorv: Roofing
Sub-Category: Modified Bitumen
Materials SBS/APP/IPO
Deck e: Wood
Maximum Desien Pressure -112.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions 5aeeification Descrintion
Elastobase 65'2"x-3'3-3/81' ASTM D 6163, SBS modified asphalt coated fiberglass reinforced
Type I base sheet.
XtraFlex SBS Glass 65' 8"x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced
Base Type I base sheet.
Polyglass G2 Base 108'x 36" ASTM D 4601 Asphalt-coated fiberglass reinforced base sheet
Type II
Polyanchor 250'x 48" ASTM b 4601 A polymer woven,high performance,synthetic base
Type II sheet.
Elastobase P- 65' 8"x 3'3-3/8" ASTM D 6164, SBS modified asphalt coated polyester reinforced base
Type I sheet.
Elastoflex SA V FR 66' 8"x 3'3-3/8" ASTM D 6163, Self-adhered,fire-rated,fiberglass reinforced,SBS
(1.5-mm) Type I modified bitumen membrane with a self-adhering back
face and a smooth top surface.
Elastoflex SA V 66' 8"x 3'3-3/8" ASTM D 6163, Self-adhered,fire-rated,fiberglass reinforced,SAS
PLUS FR Type I modified bitumen membrane with,a self-adhering back
face and a smooth top surface.
Elastoflex SA V(1.5- 66' 8"x 3' 3-3/8" ASTM D 6163, Self-adhered,fiberglass reinforced,SBS modified
mm) Type I bitumen membrane with'a self-adhering back face and
a smooth top surface.
Elastoflex SA V 66' 8"x 3' 1-No" ASTM D 6163, Self-adhered,fiberglass reinforced,SBS modified
PLUS Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
XtraFlex SBS Base 66'8"x 3' V&" ASTM D 6163; Self-adhered,fiberglassireinforced,SBS modified
SA Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA P FR 32' 10"x 3' 3-3/8" ASTM D 6164, Self-adhered,fire-rated,polyester reinforced,SBS
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
XtraFlex SBS G SA 32' 10"x 3'3-3/8" ASTM D 6164, Self-adhered,fire-rated,polyester reinforced,SBS
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
NOA No.: 17-1004.09
ieCourrnr Expiration Date: 10/11/22.
Approval Date:10/32/17
Page 2 of 34
Elastoflex SA P 32' 10"x 3' 3-3/8" ASTM D 6164, Self.-adhered,fiberglass reinforced,SBS modified'
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
XtraFlex APP S 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a bum off polyethylene back
face and a smooth or sanded top surface.
Polybond 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
Polyflex G 32' 10"x 3'3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a bum off polyethylene back
face and a granule top surface.
Polyflex SA P 32' 10"x 3' 33/s" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex SA P FR 32' 10"x 3'33/s" ASTM D 6222, Self-adhered,fire-rated,polyester reinforced,APP
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
XtraFlex APP G SA 32' 10"x 3'3-3!s" ASTM D 6222, Self-adhered,fire-rated,polyester reinforced,APP
Type I modified bitumen membrane with a self-adhering back
` face and a granule top surface.
Polyfresko G SBS SA 32' 10"x 3' 33/s" ASTM D 6164, Self-adhered,fiberglass reinforced,SBS modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko G SBS SA 32' 10"x 3' 33/s" ASTM D 6164, Self-adhered,fire-rated,fiberglass reinforced,SBS
,FR Type 1 modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polyfresko G APP SA 32' 10"x 3' 3-3/g" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko G APP SA 32' 10"x 3'V1s" ASTM D 6222, Self-adhered,fire rated,polyester reinforced,APP
FR Type I modified bitumen membrane with a self-adhering back
face and a granule top surface
PolyKool 32' 10"x 3'Ph" ASTM D6222 Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
XtraFlex Kool APP S 32' 10"x 3'3318" ASTM D6222 Self-adhered,polyester reinforced,APP modified
SA Type I bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
Polyglass APP Base 65' 8"x 3' 3-3/s" ASTM D 6509 APP modified asphalt coated fiberglass reinforced
Type I base sheet.
NOA No.: 17-1004.09
COu�rrWA Expiration Date: 10/11/22
Approval Date:10/12/17
Page 3 of 34
PG325 Cold Process 1,3,5,50,55 gal.or ASTM D3019 A fibered cold process adhesive for use with roll or
Adhesive tube Type III BUR roofing.
PG100 Asphalt Primer 1,3,5,50,55 gal, ASTM D41 A penetrating solution of solvent and a blend of
tube or 17 oz.spray selected asphalts used to promote adhesion.
can
XtraFlex 10 Asphalt 1,3,5,50,55 gal, ASTM D41 A penetrating solution of solvent and a blend of
Primer tube or 17 oz.spray selected asphalts used to promote adhesion.
can
PG350 Mod Bit 1,3,5,50,55 gal.or ASTM D3019 A fibered rubberized adhesive designed for use with
Adhesive tube Type III modified bitumen membranes.
P0400 Plastic Roof 1,3,5,50,.55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use in
Cement tube ASTM D3409 dry or damp conditions.
PG425 Wet/Dry Roof 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use in
Cement tube ASTM D3409 ,dry or damp conditions.
PG450 Flashing 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement.
Cement tube
PG500 MB Flashing 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use
Cement tube with modified-bitumen membranes.
Polyplus 35 Premium 1,3,5,50,55 gal.or ASTM D3019 A fibered rubberized adhesive designed for use with
Mod Bit Adhesive r tube Type III modified bitumen membranes.
XtraFlex 35 Premium 1,3,5,50,55 gal.or ASTM D3019 A fibered rubberized adhesive designed for use with
Mod Bit Adhesive tube. Type III modified bitumen membranes.
Polyplus 45 Premium 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement.
Flashing Cement tube
Polyplus 50 Premium 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use
MB Flashing Cement tube with modified bitumen membranes.
XtraFlex 50 Premium 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use
Modified Wet/Dry tube with modified bitumen membranes.
Cement
Polyplus 55 Premium 1,3,5,50,55 gal.or ASTM D4586 A mastic compound for use as a roof flashing
Modified Flashing tube adhesive.
Cement
NOA No.: 17-1004,09
atE ¢cD,! Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 4 of 34
4
APPROVED INSULATIONS:'
TABLE 2
Product Name Product Description Manufacturer
(With Current NOA)
Polytherm-H Polyisocyanurate foam insulation Polyglass USA,Inc.
Polytherm Polyisocyanurate foam insulation Polyglass USA,Inc.
ACFoam-H Polyisocyanuratc foam insulation Atlas Roofing Corp
ACFoam-M Polyisocyanurate foam insulation Atlas Roofing Corp
High Density Wood Fiberboard Wood fiber insulation board Generic
DensDeck,DensDeck Prime Gypsum insulation board Georgia-Pacific Gypsum LLC
H-Shield Polyisocyanurate foam insulation Hunter Panels,LLC
H-Shield CG Polyisocyanurate/perlite composite insulation Hunter Panels,LLC
ENRGY-3 Polyisocyanurate foam insulation Johns Manville Corp.
Fesco Board Expanded mineral fiber Johns Manville Corp.
Multi-Max FA-3 Polyisocyanurate foam insulation Rmax Operating,LLC.
SECUROCK Gypsum-Fiber Roof Board Fiber reinforced coverboard United States Gypsum
Corporation
t
MIAMI. DECOUNTI
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 5 of 34
APPROVED FASTENERS:
TABLE 3
Fastener Product Product Manufacturer
Number Name Description Dimensions (With Current NOA)
1. Dekfast Fasteners 12, 14& Insulation fastener for wood, SFS Intec,Inc.
15 HS steel and concrete decks -
2. Dekfast Galvalume Steel Galvalume hex stress plate. 2 7/A"x SFS Intec,Inc.
Hex Plate /31/4"t
3. #14 Roofgrip Insulation and membrane, Various OMG,Inc.
fastener
4. Flat Bottom Metal Plate A2-SS aluminized steel plate 3"square OMG,Inc.
5. Trufast#14 HD Fastener Insulation fastener for steel and Altenloh,Brinck&Co.
wood decks U.S.,Inc.
6. Trufast 3"Metal Insulation Round Galvalume AZ54 steel 3.23 round Altenloh,Brinck&Co.
Plate plate 3"round U.S.,Inc.
7. Polygrip Fasteners#12,#14 Insulation fastener for wood, Various Polyglass USA,Inc
 steel and concrete decks
8. Polygrip Hex Plates Galvalume hex stress plate. 2'/s"x Polyglass USA,Inc
31/4"
NOA No.: 17-1004.09
Ems, Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 6 of 34
APPROVED SURFACING:
TABLE 4
Product Product Application Specification Manu
Name Description Rate er
P0200 Non-Fibered Roof Coating A non fibercd asphaltic coating used 11/Z-2 gal/sq TAS 140 Polyglass
to add life and rejuvenate existing USA,Inc.
BUR roofing substrates.
XtraFlex 20 Bituminous Roof A non fibered asphaltic coating used 1%2-2 gal/sq TAS 140 Polyglass
Coating to add life and rejuvenate existing USA,Inc.
BUR roofing substrates.
PG300 Fibered Roof Coating An asphalt cutback fibered roof 1'/2-2 gal/sq ASTM D4479 Polyglass
coating. May be applicd'by brush or USA,Inc.
spray equipment to rejuvenate aged
BUR
XtraFlex Bituminous Roof An asphalt cutback fibered roof 1'/r2 gal/sq ASTM D4479 Polyglass
Coating Fibered coating. May be applied by brush or USA,Inc.
spray equipment to rejuvenate aged
BUR
PG600 Non-Fibered Aluminum Non-fibered aluminum roof coating. '/2-1 gal/sq ASTM D2824 Polyglass
Roof Coating Type I USA,Inc.
P0650 Fibered Aluminum Roof Fibered aluminum roof coating. 1%z-2 gal/sq ASTM D2824 Polyglass
Coating Type III USA,Inc.
P0700 Elastomeric Roof Coating A premium white elastomeric acrylic 1-1'/z gal/sq ASTM D6083 Polyglass
based roof coating(water-based). A USA,Inc.
polyester fabric may be used for
reinforcement with this coating.
PG800 Non-Fibered Asphalt An asphalt base,un-fibered clay 3 gal/sq in ASTM D1227 Polyglass
Emulsion Roof Coating emulsion two coats USA,Inc.
XtraFlex 80 Emulsion Roof An asphalt base,un-fibered clay 3 gal/sq in ASTM D1227 Polyglass
Coating emulsion two coats USA,Inc.
PG850 Fibered Asphalt Emulsion An asphalt base,fibered clay 3 gal/sq in ASTM D1227 Polyglass
Roof Coating emulsion two coats USA,Inc.
Polyplus 65 Premium Fibered Fibered aluminum roof coating. M-2 gal/sq ASTM D2824 Polyglass
Aluminum Roof Coating Type III USA,Inc.
XtraFlex 65 Aluminum Roof Fibered aluminum roof coating. I%2-2 gal/sq ASTM D2824 Polyglass
Coating Fibered Type III USA,Inc.
Polyplus 60 Premium Non- Non-fibered aluminum roof coating. %i-1 gal/sq ASTM D2824 Polyglass
Fibered Aluminum Roof Coating Type I USA,Inc.
XtraFlex 60 Aluminum Roof Non-fibered aluminum roof coating. %:-1 gal/sq ASTM D2824 Polyglass
Coating Type I USA,Inc.
IVOA No.: 17-1004.09
C14 .°A°E Expiration Date: 10/11/22
•
Approval Date: 10/12/17
Page 7 of 34
APPROVED SURFACING:
TABLE 4
Product Product Annlication Specification Manufactur
Name Descrintlon Rate er
Polybrite 70 Premium Grade A premium white elastomeric acrylic 1-1%i gal/sq ASTM D6083 Polyglass
Elastomerle Roof Coating based roof coating(water-based). A USA,Inc.
polyester fabric may be used for
reinforcement with this coating.
XtraFlex 70 Premium Acrylic FR A premium white elastomeric acrylic 1-1'/a gal/sq ASTM D6083 Polyglass
Roof Coating based roof coating(water-based). A USA,Inc.
polyester fabric may be used for
reinforcement with this coating.
Polybrite 90 High Solids Silicone A premium grade high solids,single 1.25 gal/sq ASTM D6694 Polyglass
Roof Coating component,moisture cure,fluid USA,Inc.
applied silicone coating
XtraFlex SRC 9600 High Solids A premium grade high,solids,single 1.25 gal/sq ASTM D6694 Polyglass
Silicone Roof Coating component,moisture cure,fluid USA,Inc.
applied silicone coating
Polybr to 95 Silicone Roof A single component,solvent, 1.25 gal/sq ASTM D6694 Polyglass
Coating moisture cure silicone coating. USA,Inc.
XtmFlex SRC 8000 Silicone Roof A single component,solvent, 1.25 gal/sq ASTM D6694 Polyglass
Coating moisture cure silicone coating. USA,Inc.
Gravel To be installed in a flood coat of 400 lbs/sq N/A Generic
approved asphalt at 60 lbs/sq
Slag To be installed in a flood coat of 3001bs/sq N/A Generic
approved asphalt at 60 lbs/sq
MtAMhGADECOUNTY
NOA No.: 17-1004.09
APPROVEDI Expiration Date: 10/11/22
Approval Date:10/12/17
Page 8 of 34
EVIDENCE SUBMMED:
Test AQency Test Name/Report Report No. Date
Factory Mutual Research 4470 2W7A7.AM 08.04.94
Corporation 4450 2D5A9.AM 06.22.99
4470 3001334 02.15.00
4470 3000857 01.12.00
4470 3004091 01.12.00
4470 3012321 07.29.07
_ 4450 3014751 08.27.03
4450 3019317 06.30.04
4470 3014692 08.05.03
Trinity ERD TAS 114 11752.09.99-1 02.08.00
TAS 114 02764.09.05 09.09.05
TAS 114 02762.03.05 03.30.05
TAS 117(B)-ASTM D903 020841.06.04 06.02.04
TAS 114 -P1734.07.06-R1 02.27.07
TAS 114 P1738.02.07 02.05.07
TAS 114 P1739.01.07 01.23.07
TAS 1,17(B)-ASTM D6862 C8500SC.11.07 11.30.07
ASTM D6164/ASTM D6222 ? P10490.08.08 08.13.08
ASTM D6164/ASTM D6222 P10490.10.08-R1 .10.03.08
ASTM.D6222 P7400.03.08-R2 10.09.08
TAS 114(D)—ASTM D1876 P10070.10.08 10.09.08
ASTM D6222 P10490.10.08-2 10.30.08
FM 4470&TAS 114 P33970.03.11 03.15.11
ASTM D6163/ASTM D 4601 P33960.03.11 03.15.11
TAS 114&TAS 117(B) 11757.12.00-1-R1 04.29.13
TAS 114&TAS 117(B) 11757.04.01-1-R1 04.30.13
ASTM D6164 P37590.07.13-1 07.02.13
ASTM D6164 P37590.03.13-3A 03.06.13
ASTM D6163 P37590.03.13-2-R1 02.05.13
ASTM D6222 P37590.09.13 09.12.13
ASTM D4601/TAS 117 P45940.09.13 09.04.13
TAS 114&FM 4474 P41630.08.13 08.06.13
TAS 114(H) P13760.09.09 09.10.09
ASTM D4601 /TAS 117 P45970.05.14 05.12.14
PRT Construction Materials ASTM D6222 PUSA-061-02-02 01.28.08
Technologies
ASTM D6222 PUSA-062-02-02 12.04.08
ASTM D6163 PUSA-064-02-02 02.27.08
ASTM D6694 PUSA-134-02-01 05:16.14
ASTM D6694 PUSA-135-02-01 05.16.14
IN uNTr
NOA No.: 174004.09
Expiration Date: 10/11/22
Approval Date:10/12/17
Page 9 of 34
APPROVED ASSEMBLIES:
Membrane Type: SBS/APP
Deck Type 1I: Wood,Insulated
Deck Description: '9/32'or greater plywood or wood plank,fastened at 24"spans with#8 wood screws at 6"o.c..
System Type A(1): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: -One ply of Elastobase,XtraFlex SBS Glass Base,Polyglass G2 Base,Polyflex*,XtraFlex APP
S*,Polybond*or GAFGLAS#75 fastened to the deck as described below:
*u lth OMG fasteners and Flat Bottom Metal Plates.
Fastening#1: Attach base sheet using 11 ga,annular ring shank and 1-5/8"diameter tin caps spaced 8"o.c.
in a 4"lap and 8"o.c.in three equally spaced staggered rows in the center of the sheet.
Fastening#2: Attach base sheet using OMG#14 Roofgrip fasteners and Flat Bottom Metal Plates,Dekfast
14 with Galvalume Steel Hex Plates or Polygrip Fasteners#14'with Polygrip Hex Plates or
Trufast#14 HD Fasteners with Trufast 3"Metal Insulation Plates spaced 12"o.c.in a 4"lap
and 12"o.c.in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver(Ontionall Insulation Fasteners Fastener
Table 31 Density1fe
Any approved Polyisocyanurate listed in Table 2 1
Minimum 1"thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the sinal membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Tou Insulation Laver Insulation Fasteners Fastener
Table 3 DensitmW
DensDeek,DensDeck Prime,SECUROCK Gypsum-Fiber Roof Board
Minimum%11 thick N/A NIA
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 2040 lbs/100 fe. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V(1.5-mm),Elastoflex SA V PLUS,XtraFlex SBS Base
SA,Elastoflex SA V FR(1.5-mm)or Elastoflex SA V PLUS FR,self-adhered.
NOA No.: 17-1004,09
annManan counrrir Expiration Date: 10/11/22
Approval Date:1011.2/17
Page 10 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood,Non-Insulated ,
Deck Description: !9/3x"or greater plywood or wood plank,fastened at 24"spans with 8d common nail t 4'°o.c.
or#8 wood screws at 6"o.c.
System Type E(1): Base sheet is mechanically attached to roof deck.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approve
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table I.
s
Base Sheet: One ply of Elastobase,XtraFlex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening: Attach base sheet using I 1 ga.annular ring shank nails and 1-5/8"diameter tin caps spaced 8"
o.c.in a 4"lap and 8"o.c.in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V(i.5-mm),Elastoflex SA V PLUS,XtraFlex SBS Base
SA,Elastoflex SA V FR(1.5-mm)or Elastoflex SA V PLUS FR,self-adhered.
Membrane: One ply of Polyfresko G SBS SA,Polyfresko G SBS SA FR,Polyfresko G APP SA,
Polyfresko G APP SA FR,Elastoflex SA P,Elastoflex SA P FR,XtraFlex SBS G SA,Polyflex
SA P,PolyKool,XtraFlex Kool APP S SA,Polyflex SA P FR or XtraFlex APP G SA,self-
adhered.
Or
One ply of Polyflex G,torch-applied.
Surfacing: (Optional)Install one of the approved surfacing products listed in Table 4 to obtain des' ed
coating or required fire classification.
aximum Design
ressure: -52.5 psf;(See General limitation#7.).
HE DIADEcowary NOANo.: 17-1004.09
fi Expiration Date: 10/11/22
Approval Date:10/]2/17
Page 26 of 34