HomeMy WebLinkAboutProduct Approval (2) RECEIVED
MAR 2 7 2020 R�ci;rVea
INIAWB+At'Jli" Permitting[)epartmnp SAB 2 1010
St. Lucie Omi-- MIAMI-DADE COUNTY
p
es ittin9 De PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURtC' ifinent 11805 SW 26 Street,Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami,Florida 33175-2474
T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.eov/eeonomv,
Polyglass USA,Inc.
150 Lyon Drive
Fernley,NV 89408.
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials.The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County,and other areas where allowed by the Authority Having Jurisdiction(AHJ).
1
This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control Section
(In Miami Dade County)and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this
product or material tested for quality assurance purposes.If this product or material fails to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as.described herein,and has been designed to comply with the Florida.Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Self-Adhered Roof System over Wood Decks
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo,city,state and following
statement: "Miami Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,
for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words ad un ty Florida, and followed by the
expiration date may be displayed in advertising literature. If any p o the Ai is ay . hall be done
in its entirety.
INSPECTION:A copy of this entire NOA shall be provided to the user by the f cturer s stributors and
shall be available for inspection at the job site at the request of the Building OffREV I EW E® FOR
This NOA renews NOA# 13-1217.01 and consists of pages I through 34. CODE COMPLIANCE
The submitted documentation was reviewed by Alex Tigera. ST. LU C I E COUNTY
OCC
MIAMNOA No.: 17-1004.09
MDA 'COUNTY
Expiration Date: 10/11/22
Approval Date:10/12/17
Page 1 of 34
ROOFL TG ASSEMBLY APPROVAL
Cateeory: Roofing
Sub-Cateeorv: Modified Bitumen
Materials SBS/APP/TPO
Deck Tvoe: Wood
Maximum Desien Pressure -112.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions Specification Description
Elastobase 65'2"x 3'3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced
Type I base sheet.
XtraFlex SBS Glass 65' 8"x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced
Base Type I base sheet.
Polyglass G2 Base 108'x 36" ASTM D 4601 Asphalt-coated fiberglass reinforced base sheet
Type II
Polyanchor 250'x 48" ASTM b 4601 A polymer woven,high performance,synthetic base
Type II sheet.
Elastobase P 65' 8"x 3'3-3/8" ASTM D 6164, SHS modified asphalt coated polyester reinforced base
Type I sheet.
Elastoflex SA V FR 66' 8"x 3'3-3/8" ASTM D 6163, Self-adhered,fire-rated,fiberglass reinforced,SBS
(1.5-mm) Type I modified bitumen membrane with a self-adhering back
face and a smooth top surface.
Elastoflex SA V 66' 8"x3'3-3/8" ASTM D 6163, Self-adhered,fire-rated,fiberglass reinforced,SBS
PLUS FR Type I modified bitumen membrane with a self-adhering back
face and a smooth top surface.
Elastoflex SA V(1.5- 66' 8"x 3'3-3/8" ASTM D 6163, Self-adhered,fiberglass reinforced,SBS modified
min) Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA V 66' 8"x 3' 3-1/8" ASTM D 6163,. Self-adhered,fiberglass reinforced,SBS modified
PLUS Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
XtraFlex SBS Base 66' 8"x 3' V/8" ASTM D 6163, Self-adhered,fiberglass reinforced,SBS modified
SA Type I bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SAP FR 32' 10"x 3' 3-3/8" ASTM D 6164, Self-adhered,fire-rated,polyester reinforced,SBS
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
XtraFlex SBS G SA 32' 10"x 3' 3-3/8" ASTM D 6164, Self-adhered,fire-rated,polyester reinforced,SBS
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
MMIA MIOM E.. COUNTY NOA No.: 17-1004.09
�Fe .symp" Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 2 of 34
i
Elastoflex SA P 32' 10"x 3' 3-3/8" ASTM D 6164, Self.-adhered,fiberglass reinforced,SBS modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a hum off polyethylene back
face and a smooth or sanded top surface.
XtraFlex APP S 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a bum off polyethylene back
face and a smooth or sanded top surface.
Polybond 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a bum off polyethylene back
face and a smooth or sanded top surface.
Polyflex G 32' 10"x 3' 3-3/8" ASTM D 6222 Torch applied,polyester reinforced,APP modified
bitumen membrane with a burn off polyethylene back
face and a granule top surface.
Polyflex SA P 32' 10"x 3'V/8" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex SA P FR 32' 10"x 3'3 3/s" ASTM D 6222, Self-adhered,fire-rated,polyester reinforced,APP
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
XtraFlex APP G SA 32' 10"x 3'3 3/a" ASTM D 6222, Self-adhered,fire-rated,polyester reinforced,APP
Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polyfresko G SBS SA 32' 10"x 3' 33/g" ASTM D 6164, Self-adhered,fiberglass reinforced,SBS modified
Type I bitumen membrane with a self-adhering back face and.
a granule top surface.
Polyfresko G SBS SA 32' 10"x 3' V/8" ASTM D 6164, Self-adhered,fire-rated,fiberglass reinforced,SHS
FR Type I modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polyfresko G APP SA 32' 10"x 3' V/8" ASTM D 6222, Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko G APP SA 32' 10"x 3' 3-Ns" ASTM D 6222, Self-adhered,fire-rated,polyester reinforced,APP
FR Type I modified bitumen membrane with a self-adhering back
face and a granule top surface
PolyKool 32' 10"x 3' V/8" ASTM D6222 Self-adhered,polyester reinforced,APP modified
Type I bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
XtraFlex Kool APP S 32' 10"x 3'V/8" ASTM D6222 Self-adhered,polyester reinforced,APP modified
SA Type I bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
Polyglass APP Base 65' 8"x.3' 33/a" ASTM D 6509 APP modified asphalt coated fiberglass reinforced
Type I base sheet.
Mu I-DWE C urm NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date:10/12/17
Page 3 of 34
PG325 Cold Process 1,3,5,50,55 gal.or ASTM D3019 A fibered cold process adhesive for use with roll or
Adhesive tube Type III BUR roofing.
PG100 Asphalt Primer 1,3,5,50,55 gal, ASTM D41 A penetrating solution of solvent and a blend of
tube or 17 oz.spray selected asphalts used to promote adhesion.
can
XtraFlex 10 Asphalt 1,3,5,50, 55 gal, ASTM D41 A penetrating solution of solvent and a blend of
Primer tube or 17 oz.spray selected asphalts used to promote adhesion.
can
PG350 Mod Bit 1,3,5,50,55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with
Adhesive tube Type III modified bitumen membranes.
P0400 Plastic Roof 1,3,5,50,55 gal. or ASTM D4586 A thick,fibered,rubberized flashing cement for use in
Cement tube ASTM D3409 dry or damp conditions.
PG425 Wet/Dry Roof 1,3,5,50,55 gal. or ASTM D4586 A thick,fibered,rubberized flashing cement for use in
Cement tube ASTM D3409 dry or damp conditions.
PG450 Flashing 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement.
Cement tube
PG500 MB Flashing 1., 3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use
Cement tube with modified bitumen membranes.
Polyplus 35 Premium 1, 3,5,50,-55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with
Mod Bit Adhesive tube Type III modified bitumen membranes.
XtraFlex 35 Premium 1,3,5,50,55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with
Mod Bit Adhesive tube. Type III modified bitumen membranes.
Polyplus 45 Premium 1,3,5, 50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement.
Flashing Cement tube
Polyplus 50 Premium 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use
MB Flashing Cement tube with modified bitumen membranes.
XtraFlex 50 Premium 1,3,5,50,55 gal.or ASTM D4586 A thick,fibered,rubberized flashing cement for use
Modified Wet/Dry tube with modified bitumen membranes.
Cement
Polyplus 55 Premium 1,3,5,50,55 gal.or ASTM D4586 A mastic compound for use as a roof flashing
Modified Flashing tube adhesive.
Cement
NOA No.: 17-1004,09
MIAMtiDADe Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 4 of 34
APPROVED INSULATIONS:
TABLE 2
Product Name Product Description Manufacturer
(With Current NOA)
PolythernrH Polyisocyanurate foam insulation Polyglass USA,Inc.
Polytherm Polyisocyanurate foam insulation Polyglass USA,Inc.
ACFoam-11 Polyisocyanurate foam insulation Atlas Roofing Corp
ACFoam-Ill Polyisocyanurate foam insulation Atlas Roofing Corp
High Density Wood Fiberboard Wood fiber insulation board Generic
DensDeck,DensDeck Prime Gypsum insulation board Georgia-Pacific Gypsum LLC
H-Shield Polyisocyanurate foam insulation Hunter Panels,LLC
H-Shield CG Polyisocyanurate/perlite composite insulation Hunter Panels,LLC
ENRGY-3 Polyisocyanurate foam insulation Johns Manville Corp.
Fesco Board Expanded mineral fiber Johns Manville Corp.
Multi-Max FA-3 Polyisocyanurate foam insulation Rmax Operating,LLC.
SECUROCK Gypsum-Fiber Roof Board Fiber reinforced coverboard United States Gypsum
Corporation
CMAMMMADECMOUNTY
WOA No.: 17-1004.09
•.•. Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 5 of 34
APPROVED FASTENERS:
TABLE 3
Fastener Product Product, Manufacturer
Number Name Descriution Dimensions (With Current NOA)
1. Dekfast Fasteners 12, 14& Insulation fastener for wood, SFS Intec,Inc.
15 HS steel and concrete decks
2. Dekfast Galvalume Steel Galvalume hex stress plate. 21/8 to x SFS Intec,Inc.
Hex Plate 31/49$
3. #14 Roofgrip Insulation and membrane Various OMG,Inc.
fastener
4. Flat Bottom Metal Plate A2-SS aluminized steel plate 3"square OMG,Inc.
5. Trafast#14 HD Fastener Insulation fastener for steel and Altenloh,Brinck&Co.
wood decks U.S.,Inc.
6. Trufast 3"Metal Insulation Round Galvalume AZ50 steel 3.23 round Altenloh,Brinck&Co.
Plate plate 3"round U.S.,Inc.
7. Polygrip Fasteners#12,#14 Insulation fastener for wood, Various Polyglass USA,Inc
 steel and concrete decks
8. Polygrip Hex Plates Galvalume hex stress plate. 2 7/8"x Polyglass USA,Inc
31/411
NOA No.: 17-1004.09
M1AMNI ADE COUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 6 of 34
.................--- _
APPROVED SURFACING:
TABLE 4
Product Product Application Specification Manufactur
Name Description Rate M.
P0200 Non-Fibered Roof Coating A non fibered asphaltic coating used 1'/2-2 gat/sq TAS 140 Polyglass
to add life and rejuvenate existing USA,Inc.
BUR roofing substrates.
XtraFlex 20 Bituminous Roof A non fibered asphaltic coating used 1%2-2 gal/sq TAS 140 Polyglass
Coating to add life and rejuvenate existing USA,Inc.
BUR roofing substrates.
P0300 Fibered Roof Coating An asphalt cutback fibered roof 1'/2-2 gal/sq ASTM D4479 Polyglass
coating. May be applied by brush or USA,Inc.
spray equipment to rejuvenate aged
BUR
XtraFlex Bituminous Roof An asphalt cutback fibered roof 1'/s-2 gal/sq ASTM D4479 Polyglass
Coating Fibered coating. May be applied by brush or USA,Inc.
spray equipment to rejuvenate aged
BUR
PG600 Non-Fibered Aluminum Non-fibered aluminum roof coating. %2-I gal/sq ASTM D2824 Polyglass
Roof Coating Type I USA,Inc.
PG650 Fibered Aluminum Roof Fibered aluminum roof coating. 1%2-2 gal/sq ASTM D2824 Polyglass
Coating Type III USA,Inc.
PG700 Elastomeric Roof Coating A premium white elastomeric acrylic 1-1%2 gal/sq ASTM D6083 Polyglass
based roof coating(water-based). A i USA,Inc.
polyester fabric may be used for
reinforcement with this coating.
PG800 Non-Fibered Asphalt An asphalt base,un-fibered clay 3 gal/sq in ASTM D1227 Polyglass
Emulsion Roof Coating emulsion two coats USA,Inc.
XtraFlex 80 Emulsion Roof An asphalt base,un-fibered clay 3 gal/sq in ASTM D1227 Polyglass
Coating emulsion two coats USA,Inc.
PG950 Fibered Asphalt Emulsion An asphalt base,fibered clay 3 gaUsq in ASTM D1227 Polyglass
Roof Coating emulsion two coats USA,Inc.
Polyplus 65 Premium Fibered Fibered aluminum roof coating. fl%2-2 gal/sq ASTM D2824 Polyglass
Aluminum Roof Coating Type III USA,Inc.
XtraFlex 65 Aluminum Roof Fibered aluminum roof coating. 1'12-2 gal/sq ASTM D2824 Polyglass
Coating Fibered Type III USA,Inc.
Polyplus 60 Premium Non- Non-fibered aluminum roof coating. %2-1 gal/sq ASTM D2824 Polyglass
Fibered Aluminum Roof Coating Type I USA,Inc.
XtraFlex 60 Aluminum Roof Non-fibered aluminum roof coating. ''/2-1 gal/sq ASTM D2824 Polyglass
Coating Type I USA,Inc.
Mwai paoE CO NOA.No.: 17-1004.09
,,.,$ Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 7 of 34
APPROVED SURFACING:
TABLE 4
Product Product Avulication Manufactur
Name Description Rate Snecifcation er
Polybrite 70 Premium Grade A premium white elastomeric acrylic 1-1'/2 gal/sq ASTM D6083 Polyglass
Elastomeric Roof Coating based roof coating(water-based). A USA,Inc.
polyester fabric may be used for
reinforcement with this coating.
XtraFlex 70 Premium Acrylic FR A premium white elastomeric acrylic 1-1'/z gal/sq ASTM D6083 Polyglass
Roof Coating based roof coating(water-based). A USA,Inc.
polyester fabric may be used for
reinforcement with this coating.
Polybrite 90 High Solids Silicone A premium grade high solids,single 1.25 gaUsq ASTM D6694 Polyglass
Roof Coating component,moisture cure,fluid USA,Inc.
applied silicone coating
XtraFlex SRC 9600 High Solids A premium grade high solids,single 1.25 gal/sq ASTM D6694 Polyglass
Silicone Roof Coating component,moisture cure,fluid USA,Inc.
applied silicone coating
Polybrite 95 Silicone Roof A single component,solvent, 1.25 gal/sq ASTM D6694 Polyglass
Coating moisture cure silicone coating. USA,Inc.
XtraFlex SRC 8000 Silicone Roof A single component,solvent, 1.25 gal/sq ASTM D6694 Polyglass
Coating moisture cure silicone coating. USA,Inc.
Gravel To be installed in a flood coat of 400 lbs/sq N/A Generic
approved asphalt at 60 lbs/sq
Slag To be installed in a flood coat of 300 lbs/sq N/A Generic
approved asphalt at 60 lbs/sq
NOA No.: 17-1004.09
MtAMM=ECOMMM Expiration Date: 10/11/22
Approval Date:10/12/17
Page 8 of 34
EVIDENCE SUBMITTED:
Test AL-en Test Name/Report Report No. Date
Factory Mutual Research 4470 2W7A7.AM 08.04.94
Corporation 4450 2D5A9.AM 06.22.99
4470 3001334 02.15.00
4470 3000857 01.12.00
4470 3004091 01.12.00
4470 3012321 07.29.07
4450 3014751 08.27.03
4450 3019317 06.30.04
4470 3014692 08.05.03
Trinity ERD TAS 114 11752.09.99-1 02.08.00
TAS 114 02764.09.05 09.09.05
TAS 114 02762.03.05 03.30.05
TAS 117(B)-ASTM D903 020841.06.04 06.02.04
TAS 114 P1734.07.06-R1 02.27.07
TAS 114 P1738.02.07 02.05.07
TAS 114 P1739.01,07 01.23.07
TAS 1.17(B)-ASTM D6862 C8500SC.11.07 11.30.07
ASTM D6164/ASTM D6222 P l 0490.08.08 08.13.08
ASTM D6164/ASTM D6222 P10490.10.08-R1 10.03.08
ASTM D6222 P7400.03.08-R2 10.09.08
TAS 114(D)—ASTM D1876 P10070.10.08 10.09.08
ASTM D6222 P10490.10.08-2 10.30.08
FM 4470&TAS 114 P33970.03.11 03.15.11
ASTM D6163/ASTM D 4601 P33960.03.11 03.15.11
TAS 114&TAS 117(B) 11757.12.00-1-R1 04.29.13
TAS 114&TAS 117(B) 11757.04.01-1-R1 04.30.13
ASTM D6164 P37590.07.13-1 07.02.13
ASTM D6164 P37590.03.13-3A 03.06.13
ASTM D6163 P37590.03.13-2-R1 02.05.13
ASTM D6222 P37590.09.13 09.12.13
ASTM D4601 /TAS 117 P45940.09.13 09.04.13
TAS 114&FM 4474 P41630.08.13 08.06.13
TAS 114(H) P13760.09.09 09.10.09
ASTM D4601 /TAS 117 P45970.05.14 05.12.14
PRI Construction Materials ASTM D6222 PUSA-061-02-02 01.28.08
Technologies
ASTM D6222 PUSA-062-02-02 12.04.08
ASTM D6163 PUSA-064-02-02 02.27.08
ASTM D6694 PUSA-134-02-01 05.16.14
ASTM D6694 PUSA-135-02-01 05.16.14
MIAMWAOE NOA No.: 17-1004.09
... COUNTY Expiration Date: 10/11/22
Approval Date:10/12/17
Page 9 of 34
rAll
ane Type: SBS/APP
ype 1: Wood,Non-Insulated
escription: 19/32"or greater plywood or wood plank,fastened at 24"spans with 8d common naiP)tothe
or#8 wood screws at 6"o.c.
Type E(1): Base sheet is mechanically attached to roof deck.
eral and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not ll not be installed unless said accessories demonstrate c 1 aomp i nce with prescriptive Florida Buquirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply f Elastobase XtraFlex SHS Glass Base, Elastobase P or Polyanchor fastedeck as deselow:
Fastening: Attach base sheet using 11 ga.annular ring shank nails and 1-5/8"diameter tin capso.c.in a 4"lap and 8"o.c.in three equally spaced staggered rows in the center of th
Ply Sheet: One or more pliesf Elastoflex SAV 5-nun),Elastoflex SAV PLUS,XtraFlex SBS Base
SA,Elastoflex SAV FR-M.3--mm)or Elastoflex SA V PLUS FR,self-adhered.
Membrane: One ply of Polyfresko G SB sko G SBS SA FR,Polyfresko G APP SA,
Poiyfresko G APP SA FR astoflex SA P lastoflex SA P FR,XtraFlex SBS G SA,Polyfle
SA P,PolyKool,XtraFlex oo ,Polyflex SA P FR or XtraFlex APP G SAS
adhered.
Or
One ply of Polyflex G,torch-applied.
Surfacing: (Optional)Install one of the approved surfacing products listed in Table 4 to obtain de ' ed.
coating or required fire classification.
a3amum Design
ressure: -52.5 psf;(See General limitation#7.).
MIAM4�ApE COUNTY
NOA No.: 17-1004.09
D Expiration Date: 10/11/22
Approval Date:10/12/17
Page 26 of 34
i
Bas Home i Log In User Registration 1 Hot Topic F Submft Surcharge Slats&Facts Publlcatlon5 ? Contact US BaS Site Map Links ;'Search I
�I rich vv ��
r Product Approval
USER;Public User
Product Aonroval Menu>Product or AnnitdUan Search>egRjicatlon Lkt>Application Detail
2
A,, EP Z
� FL# FL23089-R2
Application Type Revision
Code Version 2017
Application Status Approved
*Approved by DBPR.Approvals by DBPR shall be reviewed and ratified by the POC
and/or the Commission if necessary.
Comments
Archived
Product Manufacturer Sun Tek Mfg RECEIVED
Address/Phone/Ercall 10303 General Or
Orlando,FL 32824
(407)859-2117 BAR 2`� 1010
jfeudner@sun-tek.com
p�rinittln�gepartm�nt
Authorized Signature James Feudner
engineering@sun-tek.com
Technical Representative James Feudner
Address/Phone/Email 10303 General Dr
Orlando,FL 32824
engineering@isun-tek.com
Quality Assurance Representative James Feudner
Address/Phone/Emall 10303 General Dr
Orlando,FL 32824
(407)859-2117 Ext 111
engineering@sun-tek.com
Category Sky Lights
Subcategory Skylight
Compliance Method Certification Mark or Usting
Certification Agency Miami-Dade BCCA-CER
Validated By Miami-Dade BCCO-VAL
Referenced Standard and Year(of Standard) standard
TAS 201 - �9
TAS 2020 C19
TAS 203 1994
Equivalence of Product Standards
Certified By
263
�+ R EWE®
Product Approval Method Method 1Option A ODECOMPypL��I {A
�py■y■ COUNTY C
om, �
Date Submitted 11/26/2018 ��
Date Validated 05/01/2019
Date Pending FBC Approval
Date Approved 05/06/2019
Summm of Products
F=L
Yt Model,Number or Name Description
23089.1 CMA-D CMA-D Aluminum Skylight
Limits of Use Certification Agency Certificate
Approved for use in HVHZ:Yes FI 23089 R2 C CAC CMA-D17102320.plff
Approved for use outside HVHZ:Yes Quality Assurance Contract Expiration Date
Impact Resistant:Yes 02/22/2021
Design Pressure:+60/-60 Instaliatlon Instructions
Other: FL23089 R2 II CMA-D17102320.11df
Verified By:Miami-Dade BCCO-CER
Created by Independent Third Party:
Evaluation Reports
Created by Independent Third Party:
23089.2 HSF Hurricane Self Flashing(HSF)Aluminum Skylight
Limits of Use Certification Agency Certificate
Approved for use in HVHZ:Yes FL23089 R2 C CAC HSF17102319.pdff
Approved for use outside HVHZ:Yes Quality Assurance Contract Expiration Date
Impact Resistant:Yes 01/10/2021
Design Pressure:+60/-60 Installation Instructions
Other: FL23089 R2 II HSF17102319.Ddf
Verified By:Miami-Dade BCCO-CER
Created by Independent Third Party.
Evaluation Reports
Created by Independent Third Party:
23089.3 ICMG ICMG skylight system
Limits of Use Certification Agency Certificate
Approved for use in HVHZ:Yes fl 73089 R2 C CAC ICMG18071604.odf
Approved for use outside HVHZ:Yes Quality Assurance Contract Expiration Date
Impact Resistant:Yes 10/10/2023
Design Pressure:+80/-80 Installation Instructions
Other FL23089 R2 II ICMG18071604.odf
Verified By:Miami-Dade BCCO-CER
Created by Independent Third Party:
Evaluation Reports
emoted dent Third Party:
23089.4 ISFG ISFG skylight system
Limits of Use Certification Agency Certificate
Approved for use in HVHZI Yes FL23089 R2 C CAC ISFG18071603.odf
Approved for use outside NVHZ:Yes Quality Assurance Contract Expiration Date
Impact Resistant:Yes 10/31/2023
Design Pressure:+80/-80 Installation Instructions
Other. FL23089 R2 II ISFG18071603.odf
Verified By:Mlaml-Dade BCCO-CER
Created by Independent Third Party:
Evaluation Reports
Created b In
23089.5 MD-CMA MD-CMA Skylight
Limits of Use Certiflcatlon Agency Certificate
Approved for use in NVHZ:Yes FL23089 R2 C CAC MDCMA17102318.pd
Approved for use outside HVHZ:Yes Quality Assurance Contract Expiration Date
Impact Resistant:Yes 03/13/2023
Design Pressure:+60/-60 Installation Instructions
Other: FL23089 R2 II MDCMA17102318.pd
Verified By:Mlami-Dade BCCO-CER
Created by Independent Third Party:
Evaluation Reports
Created by Independent Third Party:
23089.6 Sun Tek Tubular skylight curb mounted tube skylight
Limits of Use Certification Agency Certificate
Approved for use In HVHZ:Yes FL23089 R2 C CAC Tube18041802.pd
Approved for use outside HVHZ:Yes Quality Assurance Contract Expiration Date
Impact Reslstant:Yes 05/26/2023
Design Pressure:+65/-65 installation Instructions
Other FL23089 R2 II Tube16041802.pdj
Verified By:Miami-Dade BCCO-,CER
Created by Independent Third Party:
Evaluation Reports
Created by Independent Third Party:
ED ED
Contact us;:2601 Blair Stare Road.Tallahassee FL 92390 Phone:RSO.467-1624
The State of Florida Is an AA/M employer.,CMV ioht 2007-2013 State of 1loride.::Privaev Stetament::Axesslbiilty Statement;:Refund Statement
Under Florida law,email addresses are public records.If you do not want your e-mall address released In response to a pubAarecords request,do not send electronic mall to this entity.Instead,
contact the office by phone or by traditional mall.If you have any questions,please contact 850.487.1395."pursuant to Section 455.275(1),Florida Statutes,effective October 1,2012,licensers
licensed under Chapter 455,F.S.must provlde the Department with an small address If they have one.The smalls provided may be used for official communication with the licensee.However email
addresses are public record.If you do not wish to supply a personal address,please provide the Department with an email address which ran be made available to the public.Tb determine If'you are
a licensee under Chapber 455,F S.,please dict hc[r_
Product Approval Accepts:
® lCt54