HomeMy WebLinkAboutProduct approvalsNEMO I etc.
Certificate of Authorization #32455
353 Christian Street, Unit #13
Oxford, CT 06478
(203)262-9245
ENGINEER EVALUATE TEST CONSULT CERTIFY
EVALUATIONREPORT
Polyglass USA, Inc. Evaluation Report P12060.02.09 -R25
1111 West Newport Center Drive FL5259-R29
Deerfield Beach, FL 33442
(954)233-1230
Date of Issuance: 02/24/2009
Revision 25: 10/14/2019
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for
use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described
herein have been evaluated for compliance with the 61h Edition (2017) Florida Building Code sections noted herein.
DESCRIPTION: Polyglass Roof Underlayments
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this
Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. of any changes to the
product(s), the Quality Assurance or the production facility location(s). NEMO Ietc. requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "NEMOletc. Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report Is displayed, then It shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 16.
Prepared by:IT.,
WITT .
PST..,, -
a
:o`'�c3F •`
Robert J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCAANE1983
%S�rwacy,;.c
�'f•"I•,n°"•
CERTIFICATION OF INDEPENDENCE:
The facsimile seal appearing was authorized by Robert Nleminen, P.E. on
10/14/2019. This does not serve as an electronically signed document,
1. NEMO Ietc. does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEMO I etc. is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
S. This is a building code evaluation. Neither NEMO Ietc. nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
02019 NEMO ETC, LLC
NNEMOletc.
1. SCOPE:
Product Category: Roofing
Sub -Category: Underlayment
Compliance Statement: Roof Underlayments, as produced by Polyglass USA, Inc., have demonstrated compliance with the
following sections of the 491 Edition (2017) Florida Building Code through testing in accordance with the following Standards.
Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein.
12. STANDARDS:
Section
Property
Standard
Year
1504.3.1
Wind Uplift
FM 4474
2011
1504.3.1
Wind Uplift
UL 1897
2012
1507.2.3
/ 1507.1.1
Physical Properties
ASTM D226
2009
1507.2.4
/ 1507.1.1, 1507.2.9.2
Physical Properties
ASTM D1970
2015
1507.3.3
Physical Properties
FRSA/TRI April 2012
2012
1507.11.2
Physical Properties
ASTM D6163
2008
1507.11.2
Physical Properties
ASTM D6164
2011
1507.11,2
Physical Properties
ASTM D6222
2011
1507.11.2
Physical Properties
ASTM D6509
2009
TAS 110
Accelerated Weathering
ASTM D4798
2011
3. REFERENCES:
Entity
Examination
Reference
Date
im&
Examination
Reference
Date
ERD (TST 6049)
Wind Uplift
11757.08.01-1
08/13/2001
ERD (TST 6049)
Tensile adhesion
P40390.04.15
04/03/2015
ERD (TST 6049)
Wind Uplift
11776.06.02
01/16/2003
ERD (TST 6049)
TAS 103
P44360.30.14 -R3
05/18/2015
ERD (TST 60491
Wind Uplift
P3740.01.07
01/04/2007
Ego (TST 6049)
Wind Uplift
PLYG-SC8905.05.16-1
05/17/2016
ERD (TST 6049)
ASTM D1970
P5310.04.07-1
04/11/2007
ERD (TST 6049)
ASTM D1970
PLYG-SC30130.06.16-1
06/27/2016
Ego (TST 6049)
Wind Uplift
P9260.03.08
03/21/2008
Ego (TST 6049)
Tensile adhesion
PLYG-SCI0130.06.16-2
06/27/2016
ERD (TST 6049)
Wind Uplift
P30540.11.09 -R1
11/30/2009
ERD (TST 6049)
TAS 103
PLYG-SC30130.06.16-3
06/27/2016
ERD (TST 6049)
Tensile Adhesion
P31030.11.09-1
11/30/2009
ERD (TST 6049)
ASTM D1970/D4798
PLYG-SC8080.07.16
07/16/2016
ERD (TST 6049)
Wind Uplift
P13030.11.09-2
11/30/2009
Ego (TST 6049)
Wind Uplift
PLYG-SC32025.10.16
10/12/2016
ERD (TST 6049)
ASTM D4977
P11030.11.09-3
11/30/2009
ERD (TST 6049)
TAS103
PLYG-SC13040.12.16
12/27/2016
ERD (TST 6049)
ASTM D1970
P33360.06.10
06/25/2010
ERD (TST 6049)
30/90 physicals
PLYG-SC11900.03.17
03/10/2017
Ego (TST 6049)
TAS103
P33370.03.11
03/02/2011
Ego (TST 6049)
TAS103
PLYG-SC12115.08.17
08/08/2017
Ego (TST 6049)
Tensile Adhesion
P33370.04.11
04/26/2011
ERD (TST 6049)
TA5103
PLYG-SC13035.08.17
10/31/2017
ERD (TST 6049)
ASTM D1970
P37300.10.11
10/19/2011
FM (TST 1867)
Wind Uplift
3004091
01/12/2000
ERD (TST 6049)
TAS103
P40390.08.12-1
08/06/2012
ICC-ES(EVL 2396)
IBC Compliance
ESR -1697
04/01/2019
ERD (TST 6049)
Tensile Adhesion
P40390.08.32-2
08/07/2012
M-D(CER 1592)
HVHZ Compliance
NOA 17-0614.22
07/06/2017
ERD (TST 6049)
Tensile Adhesion
041420.09.12-3
09/11/2012
MTI (TST 2508)
ASTM D4798
JX20117A
04/01/2008
ERD (TST 6049)
Wind Uplift
P39680.03.13
03/04/2013
NEMO (TST 6049)
ASTM D1970
4-PLYG-18-004.03.18
03/29/2018
ERD (TST 6049)
ASTM D1970
P45370.04.13
04/26/2013
NEMO (TST 6049)
Wind Uplift
4L-PLYG-18-003.01.19
01/11/2019
ERD (TST 6049)
Wind Uplift
P3738.02.07 -R2
04/29/2013
NEMO (TST 6049)
ASTM D6163
4S-PLYG-18-002.01.19-A
01/24/2019
ERD (TST 6049)
Wind Uplift
11757.04.01-1-R1
04/30/2013
NEMO (TST 6049)
ASTM D6222
45-PLYG-18-002.05.19-C
05/20/2019
ERD (TST 6049)
ASTM D6164
P37590.03.13 -3A
05/06/2013
NEMO (TST 6049)
TAS103
4S-PLYG-18-004.10.19-G
10/08/2019
ERD (TST 6049)
ASTM D6509
P37590.03.13 -1-R1
06/26/2013
NEMO (TST 6049)
TAS103
4S-PLYG-38-004.10.19-1
10/08/2019
Ego (TST 6049)
Wind Uplift
P41630.08.13
08/06/2013
NEMO (TST 6049)
TAS103
4S-PLYG-38-004.10.19-L
10/09/2019
ERD (TST 6049)
ASTM D4601
P45940.09.13
09/04/2013
NEMO (TST 6049)
TAS103
4j-PLYG-I9-SSUDL-01.A
10/10/2019
ERD (TST 6049)
Wind Uplift
P31751.05.03 -R3
11/26/2013
PRI (TST 5878)
Tensile Adhesion
PRI01111
04/08/2002
ERD (TST 6049)
Wind Uplift
P31781.11.03 -RS
11/26/2013
PRI (TST 5878)
TAS103
PUSA-018-02-03
07/14/2003
ERD (TST 6049)
30/90 physicals
P45270.05.14
05/12/2014
PRI (TST 5878)
TAS103
PUSA-035-02-01
09/29/2006
ERD (TST 6049)
Tensile adhesion
6020.09.14-5
09/08/2014
PRI (TST 5878)
TAS103
PUSA-055-02-02
12/10/2007
ERD (TST 6049)
Tensile adhesion
6020.09.14-6
09/08/2014
PRI (TST 5878)
ASTM D6222
PUSA-061-02-02
01/28/2008
ERD (TST 6049)
Tensile adhesion
P46520.10.14
10/03/2014
PRI (TST 5878)
ASTM D6164
PUSA-088-02-01
07/29/2009
ERD (TST 6049)
ASTM D1970/D4798
P43290.10.14
10/17/2014
Polyglass USA
P/LAffidavit
Mule -Hide Cross Ug
03/01/2008
NEMO ETC, LLC.
Evaluation Report P12060.02.09
-R25
CertfPoate of Author&ation #32455
6TH
EDITION (2017) FBC
NON-HVHZ EVALUATION
FL5259-R29
Polyglass Roof Underlayments;
(954) 233-1230
Revision
25:10/14/2019
Page 2 of 16
Entity Examination Reference Date Entity
ERD (TST 6049) TAS 103 PLYG-SC7550.03.15 03/24/2015 Polyglass USA
UL(QUA9625)
C
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
fONEMOjetc.
Examination Reference Date
Materials Affidavit Polystick Compound 08/18/2011
Quality Control Service Confirmation 09/13/2018
PRODUCT DESCRIPTION:
Product
Specification
Plant(s)
Description
Elastobase
ASTM D6163
FL
Fiberglass -reinforced, SBS modified bitumen base sheet
Elastobase P
ASTM D6164
FL
Polyester -reinforced, SBS modified bitumen base sheet
Elastoflex G TU
M -D 13-004
PA
Polyester -reinforced, modified bitumen tile underlayment
FRSA/TRI April 2012
composed of a sand -surfaced SBS modified bitumen back-
side and granule -surfaced APP modified bitumen top -side
Elastoflex S6 G
ASTM D6164
FL
Polyester -reinforced, SBS modified bitumen cap sheet
FRSA/TRI April 2012
Elastoflex S6 G FR
ASTM D6164
FL
Polyester -reinforced, SBS modified bitumen cap sheet
FRSA/TRI April 2012
Mule -Hide SA -APP Cap Sheet
ASTM D6222
FL
Polyester -reinforced, APP modified bitumen cap sheet
FRSA/TRI April 2012
HydraGuard Dual Pro
ASTM D1970
FL
Nominal 60 -mil thick dual -layer rubberized asphalt
waterproofing membrane, fiberglass reinforced, with a
polyester fabric surface
HydraGuard Tile Pro
ASTM D1970
FL
Nominal 60 -mil thick dual -layer rubberized asphalt
TAS 103
waterproofing membrane, fiberglass reinforced, with a
FRSA/TRI April 2012
polyester fabric surface
Mule -Hide SA -APP Cap Sheet
ASTM D6222
FL
Polyester -reinforced, APP modified bitumen cap sheet
(FR)
FRSA/TRI April 2012
Polyflex G
ASTM D6222
FL
Polyester -reinforced, APP modified bitumen cap sheet for
FRSA/TRI April 2012
use as an alternate to Heat Applied "Cap Sheet' in the
"Two Ply System" from FRSA/TRI April 2012 (04-12)
beneath mechanically fastened or adhered tile roof
systems
Polyflex G FR
ASTM D6222
FL
Polyester -reinforced, APP modified bitumen cap sheet for
FRSA/TRI April 2012
use as an alternate to Heat Applied "Cap Sheet' in the
"Two Ply System" from FRSA/TRI April 2012 (04-12)
beneath mechanically fastened the roof systems
Polyflex SA P
ASTM D6222
FL
Polyester -reinforced, APP modified bitumen cap sheet
FRSA/TRI April 2012
Polyflex SA P FR
ASTM D6222
FL
Polyester -reinforced, APP modified bitumen cap sheet
FRSA/TRI April 2012
Polyglass Base
ASTM D6SO9
FL
Fiberglass -reinforced, APP modified bitumen base sheet
Polyglass G2 Base Sheet
ASTM D4601
AL
Fiberglass -reinforced, asphaltic base sheet
Polystick IR -Xe
ASTM D1970
FL, PA
Nominal 60 -mil thick rubberized asphalt waterproofing
membrane, glass fiber reinforced, with an aggregate
surface
Polystick MTS Plus
TAS 103
FL, PA, TX
Nominal 60 -mil thick rubberized asphalt waterproofing
FRSA/TRI April 2012
membrane, glass fiber reinforced, surfaced with
polyolefinic film surface
NEMO ETC, LLC. Evaluation Report P12060.02.09-1125
Certilcate of Authorization#32455 15- EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R29
Polyglass Roof Underlayments; (954) 233-1230 Revision 25:10/14/2019
Page 3 of 16
4.
4.18
4.19
4.20
4.21
ONEMOJetc.
PRODUCT DESCRIPTION:
Product
Specification
Plant(s)
Description
Polystick MU -X
ASTM D1970
FL, NV, PA
Nominal 54 -mil thick dual -layer rubberized asphalt
(See Section 5.8)
waterproofing membrane, fiberglass reinforced, with a
Underlayment
Asphalt Shingles
polypropylene film surface
Polystick TU Max
ASTM D1970
FL, PA, TX
Nominal 60 -mil thick rubberized asphalt waterproofing
Elastobase
TAS 103
membrane with a 190 g/m2 polyester fabric surface
Yessystem) Yes
FRSA/TRI April 2012
Yes
Polystick TU P
TAS 103
TX
Nominal 130 -mil thick rubberized asphalt waterproofing
FRSA/TRI April 2012
Elastobase P
membrane, glass-fiber/polyester reinforced, with a
Yes
Yes
Yes
granular surface
Polystick TU Plus
ASTM D1970
FL, PA
Nominal 80 -mil thick rubberized asphalt waterproofing
(Base Sheet In 2 -ply system)
TAS 103
membrane, glass fiber reinforced, with a polyester fabric
Polyglass Base
FRSA/TRI April 2012
Yes
(Base Sheet In 2 -ply system)
surface
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither NEMO I etc. nor Robert Nieminen, P.E. are, in anyway, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless
retained specifically for that purpose.
5.2 This Evaluation Report is not for use in the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire ratings of
this product.
5.4 Polyglass Roof Underlayments may be used with any prepared roof cover where the product is specifically referenced within
FBC approval documents. If not listed, a request may be made to the Authority Having Jurisdiction for approval based on this
evaluation combined with supporting data for the prepared roof covering.
5.5 Allowable Roof Covers:
NEMO ETC, I.I.C. Evaluation Report P12060.02.09 -R25
Certificate of Authorization #32455 67" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R29
Polyglass Roof Underlayments; (954) 233-1230 Revision 25: 10/14/2019
Page 4 of 16
TABLE 1: ROOF
COVER OPTIONS
Wood Shakes
Underlayment
Asphalt Shingles
Nall -On Tile
Foam -On Tile
Metal
&Shingles
Slate
Elastobase
Yes
Yes
Yessystem) Yes
YES
Yes
(Base Sheet net -ply system)
(Base Sheet n
Elastobase P
Yes
Yes
Yes
Yes
Yes
Yes
(Base Sheet In 2 -ply system)
(Base Sheet In 2 -ply system)
Polyglass Base
No
Yes
(Base Sheet In 2 -ply system)
Yes
(Base Sheet In 2 -ply system)
No
No
No
Polyglass G2 Base
No
Yes
Yes
No
No
No
(Base Sheet In 2 -ply system)
(Base Sheet in 2 -ply system)
Elastoflex G TU
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Elastoflex 56 G
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Elastoflex S6 G FR
Yes
Yes
No
No
Yes
Yes
HydraGuard Dual Pro
Yes
No
No
Yes
Yes
Yes
HydraGuard Tile Pro
Yes
Yes
Yes (See 5.5.1)
Yes
Yes
Yes
Mule -Hide SA -APP Cap
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Sheet
Mule -Hide SA -APP Cap
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Sheet(FR)
PolyflexG
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Polyflex G FR
Yes
Yes
No
No
Yes
Yes
Polyflex SA P
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Polyflex SA P FR
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Polystick IR -Xe
Yes
No
No
No
Yes
Yes
NEMO ETC, I.I.C. Evaluation Report P12060.02.09 -R25
Certificate of Authorization #32455 67" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R29
Polyglass Roof Underlayments; (954) 233-1230 Revision 25: 10/14/2019
Page 4 of 16
ONEMOjeft.
5.5.1 "Foam -On Tile" is limited to use of the following Approved tile adhesives / underlayment combinations.
TABLE IA: ALLOWABLE TILE ADHESIVE / UNDERLAYMENT COMBINATIONS'
TABLE 1: ROOF COVER OPTIONS
Substrates (designed to meet wind loads for project)
Adhesive
Approval
Underiayment
Asphalt Shingles
Nail -On Tile Foam -On Tile
Metal
Wood Shakes
&Shingles
Slate
Polystick MTS Plus
Yes
Yes No
Yes
Yes
Yes
Polystick MU -X
Yes
No No
Yes
Yes
Yes
Polystick TU Max
No
Yes Yes (See 5.5.1)
Yes
No
No
Polystick TU P
No
Yes Yes (See 5.5.1)
No
No
No
Polystick TU Plus
Yes
Yes Yes (See 5.5.1)
Yes
Yes
Yes
5.5.1 "Foam -On Tile" is limited to use of the following Approved tile adhesives / underlayment combinations.
TABLE IA: ALLOWABLE TILE ADHESIVE / UNDERLAYMENT COMBINATIONS'
Florida Product
Substrates (designed to meet wind loads for project)
Adhesive
Approval
Underlayments
DAP Foam Touch 'n Seal StormBond
FL14506
Polystick TU Max or Polystick TU Plus
Roof Tile Adhesive
plywood, OSB, Southern Yellow Pine or Huber
HydraGuard Tile Pro, Polyflex SA P, Polystick TU Max, Polystick TU P or
Dow TileBond'"
FL22525
Polystick TU Plus
Engineered Woods "ZIP System" Panels
HydraGuard Tile Pro,
Elastoflex G TU, Elastoflex S6 G, HydraGuard Tile Pro, Mule -Hide SA -APP
ICP Adhesives Polyset® AH -160
FL6332
Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex G, Polyflex SA P,
Polystick (all variations),
self-
Polyflex SA P FR, Polystick TU Max, Polystick TU P or Polystick TU Plus
ASTM C1289 Type II Class 1 polyisocyanurate, ASTM
Elastoflex S6 G, HydraGuard Tile Pro, Mule -Hide SA -APP Cap Sheet, Mule -
ICP Adhesives Polyset® RTA -1
FL6276
Hide SA -APP Cap Sheet (FR), Polyflex G, Polyflex SA P, Polyflex SA P FR,
01289 Type V polyisocyanurate-composite, DensDeck
Sheet, Mule -Hide SA -APP
Polystick TU Max, Polystick TU P or Polystick TU Plus
5.6 Allowable Substrates:
TABLE 2: SUBSTRATE OPTIONS FOR ADHERED UNDERLAYMENTS
Substrates (designed to meet wind loads for project)
Underiayment
Application
Type Primer Material(s)
plywood, OSB, Southern Yellow Pine or Huber
HydraGuard Dual Pro,
Deck /
(optional) ASTM D41
Engineered Woods "ZIP System" Panels
HydraGuard Tile Pro,
sheathing
ASTM D41
structural concrete
Polystick (all variations),
self-
ASTM C1289 Type II Class 1 polyisocyanurate, ASTM
Mule -Hide SA -APP Cap
adhering
Insulation
(Optional) ASTM D41
01289 Type V polyisocyanurate-composite, DensDeck
Sheet, Mule -Hide SA -APP
or WB -3000
Prime or SECUROCK Gypsum -Fiber Roof Board
Cap Sheet (FR), Polyflex
Base
N/ A
ASTM D226 felt, Elastobase, Elastobase P or Mule -Hide
SA P or Polyflex SA P FR
Sheet
Nail Base
Deck
ASTM D41
structural concrete
Insulation
(Optional) ASTM D41
DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board
Elastoflex G TU, Elastoflex
hot asphalt
Base
ASTM D226 felt, Elastobase, Elastobase P, Mule -Hide Nail
S6 G or Elastoflex 56 G FR
Sheet
N/A
Base or Polyglass G2 Base
Deck
ASTM D41
structural concrete
Insulation
(Optional) ASTM D41
DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board
torch-
Polyflex G or Polyflex G FR
applied
Base
N/A
Elastobase, Elastobase P, Mule -Hide Nail Base, Polyglass
Sheet
G2 Base or Polyglass Base
' Refer to Tile Manufacturer's orAdhesive Manufacturer's Florida Product Approval for Overturning Moment Resistance Performance.
NEMO ETC, I.I.C. Evaluation Report P32060.02.09 -R25
Certificate of Authorization #32955 6- EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R29
Polyglass Roof Underlayments; (954) 233-1230 Revision 25:10/14/2019
Page 5 of 16
ONEMOletc.
5.6.1 Wind Resistance for Underlayment Systems in Foam -On Tile Applications:
The following wind uplift limitations apply to underlayment systems that are not prescriptively addressed in FRSA/TRI April
2012 (04-12) and are used in foam -on or mortar -set tile applications. Maximum Design Pressure is the result of testing for
wind load resistance based on allowable wind loads and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin
of safety per FBC 1504.9 has already been applied). Refer to FRSA/TRI April 2012 (04-12), Appendix A, Table 1A or FBC 1609
for determination of design wind loads.
#1 Maximum Design Pressure= -52.5 Dsf:
Deck: APA rated, 7/16 CAT, 0.418 In., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Joints: Min. 4 -inch wide strips of Elastoflex SA -V over all OSBjoints
Base Ply: Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#2 Maximum Design Pressure = -90 Dsf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: None
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#3 Maximum Design Pressure = -97.5 Dsf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG100 or ASTM D41
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered and back -nailed within the selvedge -edge side laps using 12 ga. x IY" ring shank nails
through 32 ga., 1-5/8" diameter tin caps spaced 12 -inch o.c.
#4 Maximum Design Pressure = -105 DO:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: WB -3000
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered and back -nailed within the selvedge -edge side laps using 12 ga. x 1Y" ring shank nails
through 32 ga., 1-5/8" diameter tin caps spaced 12 -inch o.c.
#5 Maximum Design Pressure = -135 Dsf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: (Optional) PG100 or ASTM D41
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Joints: Min. 4 -inch wide strips of Elastoflex SA -V over all plywood joints.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#6 Maximum Design Pressure = -315 Dsf:
Deck: Structural concrete to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG100 or ASTM D41
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: HydraGuard Tile Pro, Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR,
Polystick TU Max, Polystick TU P or Polystick TU Plus, self -adhered.
#7 Maximum Design Pressure = -622.5 Dsf:
Deck: Structural concrete to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG100 or ASTM D41
Underlayment: Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
NEMO ETC, I.I.C. Evaluation Report P12060.02.09 -R25
CertiJlmte ofAuthotlmtlon #32455 61H EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R29
Polyglass Roof Underlayments; (954) 233-1230 Revision 25: 10/14/2019
Page 6 of 16