Loading...
HomeMy WebLinkAboutNotice of AcceptanceEo MlDADE NIIAMI-DARE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 1 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION T (186) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) wymmiamidade.eov/economy PGT Industries, Inc. 1070 Technology Drive North Venice,'FL34275 SCOPE: This NOA is being issued under the applicable Hiles and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHD). This NOA shall not be valid after the expiration date stated below_ The Miami -Dade County Product Control Section (In Miami -Dade County) and/orthe AHD (in,areas other than Miami --Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the experise of such testing and the AHJ may immediately revoke; modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami —Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. II1tSCRIP�Oh1l:�5enes SIIZ00" AiuntinmmrSiagle>Eiung'T�andmv=-PIcI.—� , , APPROVAL DOCUA=i : Drawing No. MD-SH2O0-0l, fitled "SH Window installation" sheets 1 through 8 of 8, datecl'OSIl Ulf, with revision D dated 06116117, prepared by manufacturer, signed and sealed by Anthony Lynn Mille P.E.; bearing the Miami=Dade County Product Control Revision stamp with the Notice of Acceptance'number and expiration date by the Miami -Dade County Product Control Section. A41SSII E IMPACT RATING: None LABEIING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state, model/series, and following statement: "Miami Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. , TERMINATION of this NOA will occur after the expiration date or if there bas been a revision. or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall'automatically terminate this NOA_ Failure to comply with any section of this NOA shall be cause for termination and removal ofNOA- ADVERTLSEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this e'ntire'N©A shall be rovided to the user by, the manufacturer or its distributors and shall be auailabl at the request of the Building Official. This NOA revises NOA#/ 1 g� d evidence pages E-1 and E-2, as well as approval documentrm n 7e ove. � L A1�'l'i�g The submitted documentatio 09*�i��"t Boca rnarrtnaneeounrry /' I � � ``t7 [AjN_b.,r17-Q630. 2 tim2�AppnDe�• fafS1 Dae br26 2017 4FILE COPY PGT Industries. Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED A. DRAWINGS 1. Manufacturer's die drawings and sections. (Submitted under NOA No. 11-0614. 01) 2. Drawing No. MD-SW00-01, titled "SH Window Installation" sheets I through 8 of 8, dated 05111/11, with revision D dated 06116/17, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. B. TESTS , I . . 1. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 . • ' 41 Forced Entry Test, per'FBC' 24l l.3.2d,'and TAS 202-94 along with marked -up drawings and installation diagram of series SH-200 aluminum single hung window; prepared by Fenestration Testing Laboratory, Inc., Test Report No. FTL-6479, specimens I thru 26, dated. 03/28111, signed and sealed by Marlin D. Brinson, P.E. (Sabin tied uuder.NOA No.11-0614.01) C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC-51h Edition (2014) and FBC-6� Edifion'(2017) dated 10/121N,' prepared by manufacturer, signed and sealed by Anthony Lynn Miller,,P.E 2. Anchor verification calculations and structural analysis, complying with FBC-51 Edition (2014), dated 05/22/15, prepared by manufacturer,. signed and sealed by Anthony Lynn Miller, P.E. (Submitted wider NOA No.15-0528.22), 3. Glazing complies with ASTM E1300-09 D. QUALITY ASSURANCE 1. Miami -Dade Department of Regulatory and Economic Resources (RER): E. MATERIAL CERTIFICATIONS 1. None. ' F. STATEMENTS 1. Statement letter of conformance to FBC-5" Edition (M14) and FBC-6's Edition (2017), dated 06/22117, issued by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2.. Statement letter. of no financial interest, dated 06/2M7' .issued by manufacturer, signed and sealed by Anthony Lynn Miller, PE. Jorge M. Plasencia, P.E. Prod ct Control Unit Sapervisor NOA No.17-0630.02 Expiration Dater September0l, 2021 Approval Date October 26, 2017 E-I