The URL can be used to link to this page

Home My WebLink AboutNOA18 1126 06MIMImAIM111 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) BOARD AND CODE ADMINISTRATION DWISION NOTICE OF ACCEPTANCE (NOA) Firestone Building Products Company, 200 4th Ave. South Nashville, TN 37201 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION 11805 SW 26 Street, Room 208 Miami, Florida 33175-2474 T (786)315-2590 F (786) 31525.99 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (in Miami Dade County) and/or the AH1(in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the A14J may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Firestone UltraPly TPO & TPO XR Single Ply Roof Systems over Recover Decks. LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA No. 14-0606.04 and consists of pages 1 through 109. The submitted documentation was reviewed by Hamley Pacheco, P.E. L APPROVED I NOA No.: I9-1126.06 Expiration Date: 02/03/25 Approval Date: 01/M= Page I of 109 ROOFING SYSTEM APPROVAL Catevorv: Roofing Sub-Cateeorv: Single Ply Roofing Material: TPO Deck Type: Recover Maximum Desi® Pressure: See Specific Deck Type TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Dimensions Specifications Product Description UltraPly TPO Various TAS 131 Reinforced TPO 0.045" to ASTM D6878 0.080" thick membrane. UltraPly TPO XR 100 Various TAS 131 Reinforced TPO 0.045" ASTM D6878 membrane with 8 oz. fleece backing. UltraPly TPO XR 115 Various TAS 131 Reinforced TPO 0.060" ASTM D6878 membrane with8 oz. fleece backing. UltraPly TPO XR 135 Various TAS 131 Reinforced TPO .080" ASTM D6878 membrane with 8 oz. fleece backing. SBS Poly Base 39.4" x 50' ASTM D6164 Polyester reinforced SBS modified bitumen membrane with sanded surfaces. UltraPly TPO Reinforced Various TAS 131 TPO curb flashing Curb Corner ASTM D6878 UltraPly 18" Curb Various TAS 131 TPO curb flashing Flashing ASTM D6878 UltraPly TPO Various TAS 131 Molded TPO for comer flashing Inside/Outside Comer ASTM D6878 UltraPly TPO Large Pipe Various TAS 131 TPO flashing for large round Flashing ASTM D6878 penetrations UltraPly TPO T -Joint Various TAS 131 TPO flashing for T joints Cover ASTM D6878 UltraPly TPO Penetration Various TAS 131 Penetration sealing kit for Kit ASTM D6878 UltraPly TPO UltraPly TPO Walkway Various TAS 131 TPO walkway pad Pad ASTM D6878 UltraPly TPO Coated Various TAS 131 TPO laminated to hot -dipped Metal ASTM D6878 galvanized steel for flashing UltraPly TPO Premium Various TAS 131 TPO walkway pad Walkway Pad ASTM D6878 NOA No.: IS -1126.06 t*nt+Fpnpeeota+rr Expiration Date: 02/03/25 Approval Date: 01/30/20 Page 2 of 109 NOA No.: M-1126.06 nwnonpEeourrtr Expiration Date: 02/03/25 Approval Date: 01/30/20 Page 3 of 109 Test Product Dimensions Specifications Product Description UltraPly TPO Reinforced Various TAS 131 TPO flashing for round Split Pipe Boot ASTM D6878 penetrations I" to 9" in diameter UltraPly TPO 8" Various TAS 131 8" wide 60 mil TPO cover strip Reinforced Cover Strip ASTM D6878 UltmPly TPO Universal Various TAS 131 TPO flashing for round Pipe Boot ASTM D6878 penetrations V to 6" in diameter UltraPly TPO Various TAS 131 Unreinforced TPO used for Unsupported Flashing ASTM D6878 flashing UltraPly QuickSeam ]W' x 100' Proprietary Strip of UltraPly TPO with R.M.A. Strip QuickSeam Tape for anchoring membrane to substrate. Single -Ply QuickPrime 1 gallon, 3 gallon Proprietary Primer for TPO Flashing. Primer XR Bonding Adhesive 5 gal. pail Proprietary Solvent based adhesive. UltraPly Bonding 5 gal. pail Proprietary Solvent based adhesive. Adhesive XR Stick Membrane 5 gal. pail Proprietary A low-rise polyurethane, low Adhesive VOC, membrane adhesive. I.S.O. Stick 5 gal & Proprietary A dual component polyurethane 1500 ml adhesive. I.S.O. Twin Pack 1500 ml Proprietary A dual component polyurethane Insulation Adhesive adhesive. I.S.O. Fix 11 30 lbs. Proprietary A single component polyurethane adhesive. I.S.O. Spray R 15 gal pail & Proprietary A two part polyurethane 55 gal drum adhesive Single -Ply LVOC 5 gal. pail Proprietary Solvent based bonding adhesive. Bonding Adhesive Single -Ply LVOC 5 gal. pail Proprietary Solvent based bonding adhesive. Bonding Adhesive 1168 Water Based Bonding 5 gal. pail Proprietary Water based bonding adhesive. Adhesive P NOA No.: M-1126.06 nwnonpEeourrtr Expiration Date: 02/03/25 Approval Date: 01/30/20 Page 3 of 109 APPROVED INSULATIONS: Product Name ISO 95+ GL and tapered ISOGARD HD ISOGARD HD Composite RESISTA and tapered DensDeck, DensDeck Prime SECUROCK Gypsum -Fiber Roof Board SECUROCK Glass -Mat Roof Board APPROVED TABLE 2 Product Description Polyisocyanurme foam insulation Polyisocyanurate with a coated fiberglass facer Polyisocyanumte with a coated fiberglass facer composite insulation. Polyisocyanurate foam core laminated to a coated fiberglass facer. Silicon treated gypsum Rigid, gypsum -based board stock Rigid, gypsum -based board stock Manufacturer (With Current NOA) Firestone Building Products Company, LLC Firestone Building Products Company, LLC Firestone Building Products Company, LLC Firestone Building Products Company, LLC Georgia Pacific Gypsum LLC United States Gypsum Corp. United States Gypsum Corp. NOA No.: 19-1126.06 Expiration Date: 02/03/25 Approval Date: 01/30/20 Page 4 of 109 APPROVED FASTENERS: TABLE 3 Fastener Product Product Manufacturer Number Name Description Dimensions (With Current NOA) 1. Firestone Heavy -Duty #15 Fastener for steel, N/A Firestone Building Wood, concrete decks. Products Company, LLC 2. Firestone All -Purpose #14 Fastener for steel, N/A Firestone Building Wood, concrete decks. Products Company, LLC 3. Firestone Heavy Duty Plus Insulation and membrane Various Firestone Building fastener. Products Company, LLC 4. Concrete Drive Structural concrete Various Firestone Building fastener. Products Company, LLC 5. Purlin Fasteners 912 purlin fastener. Various Firestone Building Products Company, LLC 6. Insulation Fastening Plate Galvalume insulation plate. 3" diameter Firestone Building Products Company, LLC 7. Firestone HD Plus Seam Galvalume insulation plate. 2'h" Firestone Building Plate diameter Products Company, LLC 8. Firestone HD Seam Plates AZ55 or AZ50 galvalume 2-3/8" Firestone Building insulation plate. diameter Products Company, LLC 9. UltraPly TPO Invisi Weld High-performance TPO 3" diameter Firestone Building Plates membrane fastening Products Company, LLC system. 10. Metal Batten Bar Galvalume AZ55 batten 10' long, I" Firestone Building bar. wide Products Company, LLC 11. Firestone Polymer Batten Polymer batten 250' long, Firestone Building Sip 3/4" wide Products Company, LLC 12. Coiled Metal Batten Bar Galvalume AZ55 batten 220' long, P' Firestone Building strip wide Products Company, LLC 13. Two Piece Impact Nail Base ply fastening systems Various Firestone Building for lightweight concrete Products Company, LLC decks NOA No.: 18-1126.06 Expiration Date: 02/03/25 Approval Date: 01/30/20 Page 5 of 109 EVIDENCE SUBMITTED: Test Aeencv Test Identifier Description Date Underwriters Laboratories Inc. R9516 UL 790 04/26/16 Factory Mutual Research 3032272 FM 4470 05/22/09 Corporation 3036642 FM 4470 10/09/09 3030650 FM 4470 07/10/09 3035560 FM 4470 01/11/10 3019991 FM 4470 09/20/05 3017120 FM 4470 04/30/04 3038546 FM 4470 12/17/10 3039133 FM 4470 04/07/11 3036747 FM 4470 02/12/10 3040535 FM 4470 10/05/10 3035017 FM 4470 04/15/09 3038191 FM 4470 08/04/11 3036256 FM 4470 04/27/09 3038546 FM 4470 12/17/10 3038770 FM 4470 08/04/11 3041939 FM 4470 08/14/12 3044047 FM 4470 05/17/12 3047398 FM 4470 08/15/13 3047700 FM 4470 08/16/13 3050274 FM 4470 10/01/13 797-05830-267 FM 4470 08/30/10 797-10191-267 FM 4470 01/09/15 TrinitylERD F8300.07.08 TAS 131/ ASTM D6878 07/30/08 F8300.11.08 -R3 TAS 131/ ASTM D6878 02/25/11 F45600.09.13 -R1 TAS 131/ASTM D6878 12/30/13 PRI Construction Materials FBP-054-02-05, RI FM 4474/TAS 114 D 02/07/13 Technologies, LLC FBP-069-02-01, Rl FM 4474/TAS 114 J 02/07/13 FBP-070-02-01, RI FM 4474/TAS 114 J 02/07/13 FBP-085-02-01 TAS 1141 10/04/12 FBP-086-02-01 TAS 114J 10/04/12 FBP-044-02-01, R7 TAS 114 H. J 02/04/14 FBP-145-02-01 TAS 131/ASTM D6878 06/26/14 FBP-094-02-01 TAS 131/ASTM D6878 11/20/13 FBP-120-02-01 TAS 114 J 07/23/13 FBP- 122-02-0 1, RI TAS 114J 02/04/14 FBP-125-02-01 TAS 114 C 07/23/13 FBP-148-02-01 TAS 114 J 12/18/13 FBP-149-02-01 TAS 114 J 12/18/13 FBP-153-02-01 TAS 114 J 12/18/13 FBP-154-02-02 TAS 1141 12/18/13 FBP-165-02-01 TAS 114 J 04/28/14 FBP-165-02-OIA TAS 114 J 04/28/14 FBP-175-02-01 TAS 114 J 04/28/14 NOA No.: 18-1126.06 MIAMI DADE COUNTY Expiration Date: 02/03/25 Approval Date: 01/30/20 Page 6 of 109 EVIDENCE SUBMITTED: (CONTINUED Test Agency PRI Construction Materials Technologies, LLC Test Identifier Description FBP-190-02-01 TAS 114 D FBP-193-02-02 TAS 114 J FBP-196-02-04.1 TAS 114J FBP-206-02-01 TAS 114J FBP-213-02-01 TAS 114 J FBP-220-02-01.1 TAS 114J FBP-225-02-01 TAS 114 J FBP-230-02-01 TAS 114 J FBP-233-02-01 TAS 114 J FBP-233-02-02 TAS 114 C FBP-233-02-03 TAS 114J FBP-235-02-01 TAS 1141 FBP-238-02-01 TAS 114 J FBP-238-02-03 TAS 114 J FBP-239-02-01 TAS 114 J FBP-241-02-01 TAS 114J DECK STRESS ANALYSIS CALCULATIONWREPORTS Engineer/Agency Identifier Zachary R. Priest, P.E. FM Approval Deck Limitations B(8), B(9) E(2), E(3) Signed/Sealed C(18), C(22), C(23), C(24), C(25), C(41) Signed Seale C(i6), C(21). C(29), C(30), D(20), D(21). CalcuD(4), D(22), D(24) D(25), E(4), E(8) C(26), C(27) Date 07/31/14 10/16/14 10/21/14 02/02/15 11/20/14 01/29/15 03/19/15 04/02/15 06/01/15 04/03/15 06/01/15 06/01/15 07/01/15 07/15/15 07/15/15 07/22/15 06/01/15 04/18/16 10/03/16 09/20/17 10/11/17 07/10/19 N/A C(14), C(15) D(5), D(6), D(7), D(8), D(9), 01/01/13 13(10), 1)(12), D(14), D(16), D(17),1308) NOA No.: 16-1126.06 MIAMI DADE COUNTY Expiration Date: 02/03/25 Approval Date: 01/30/20 Page 7 of 109 Membrane Type: Single Ply, TPO Deck Type 71: Recover, Insulated Deck Description: Steel (Existing Structural Non -Insulated Metal Roof Panel Assembly) System Type D(3): Membrane mechanically attached over preliminary fastened insulation. All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building Code requirements and are field fabricated utilizing the approved membranes listed in Table 1. One or more layers of any of the following insulations. Base Insulation Layer: To be placed between the Insulation Fasteners Fastener ribs or over panels of existing structural metal roof (Table 3) Density/ft= system. ISO 95+ GL Minimum I" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener (Table 3) Density/ft' ISO 95+ GL Minimum 1.5" thick N/A N/A ISOGARD HD Minimum %:" thick N/A N/A DensDeck; DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board, SECUROCK Glass -Mat Fiber Roof Board Minimum '/4" thick N/A N/A Plywood Minimum 19/32" thick N/A N/A Note: All insulation shall have preliminary attachment prior to the installation of the roofing membrane at a minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4 ft., and four fasteners for any insulation board having no dimension greater than 8 ft. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Membrane: UltraPly TPO shall be mechanically attached over the top insulation to the purlins spaced 142" maximum with Firestone HD Seam Plates and Purlin Fasteners. Fastener rows are placed at a maximum 142" o.c. and fasteners are spaced 6" o.c. and centered within the 6" wide roof cover side laps. (Areas where the metal panels do not lay flush on purlin shall have a'/4" pilot pre -drilled into the panel prior to fastening) Minimum 6" wide side laps are sealed with a minimum 1.5" wide heat weld on the outside edge of the lap. Maximum Design Pressure: -52.5 psf. (See General Limitation #7) NOA No.: I8-1126.06 HAMM IDECOUDIry Expiration Date: 02/03/25 Approval Date: 01/30/20 Page 70 of 109 RECOVER SYSTEM LIMITATIONS: 1. All System Limitations and General Limitations shall apply. See specific deck type Notice of Acceptance for deck type System Limitations. 2. All assemblies listed herein shall be installed in compliance with the applicable sections of FBC 1521. Uplift performance of assemblies bonded to existing roofing system shall be verified per 1521.10. Uplift performance of assemblies mechanically attached through existing roofing system shall be verified per 1521.11. GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The fust layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 IbsJsq., or mechanically attached using the fastening pattern of the top layer. 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf. 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F) value of 275 Ibf, as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 lbf. Insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. 7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117 and/or RAS 137. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter milers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS 11 I and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and comers). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61 G20-3 of the Florida Administrative Code. END OF THIS ACCEPTANCE NOA No.: 18-1126.06 OMMM rwuaFwoecoum Expiration Date: 02/03/25 Approval Date: 01/3020 Page 109 of 109