The URL can be used to link to this page

Home My WebLink AboutSpecificationsPossible Issues with Electronic Governing See Table 7 (Common faults and their remedial actions) inside the online "Operation InsWctions GC1031 GENSET Controller' manual (part number 80086364). Specifications Generator Specifications: 17kW and 20KW ' 17k Watt. Rated Maximum Load Current' (at 25'C777'F, LP)': at 240 Volts 70.8 Amps Rated AC Voltage 120/240 Volts Phase Single phase Rated Frequency 60 Hertz Generator Breaker 80 Amp Normal Operating Range -20'F (-28.8'C) to 104-F (40'C) Output Sound Level 69.1 dB(A) at 23IL (7 m) at normal load Shipping Weight 1610 lb (278 kg) 20k Watt Rated Maximum Load Current' (at 25'C/77'F, LP)': at 240 Volts 83.3 Amps Rated AC Voltage 1201240 Volts Phase Single phase Rated Frequency 60 Hertz Generator Breaker 100 Amp Normal Operating Range -20-F (-28.8-C) to 104-F (40-C) Output Sound Level 69.1 dB(A) at 23 ft. (7 m) at normal load Shipping Weight 1626 lb (278 kg) ' Natural gas rating will depend on specific fuel but typical derates are between 10 to 20% off the LP gas rating. Engine Specifications . 17k Watt. Displacement 60.60 ci. (993 cc) Bore 3.405 In. (86.5 mm) Stroke 3.366 In. (85.5 mm) Spark Plug Gap 0.020 in. (0.51 mm) Spark Plug Torque 180 lb -in. (20 Nm) Armature Air Gap 0.005 - 0.008 in. (0.13 - 0.20 mm) Intake Valve Clearance 0.004.0.006 in. (0.10 - 0.15 mm) Exhaust Valve Clearance 0.007 - 0.008 in. (0.15 - 0.20 mm) Oil Type SW30 Synthetic Oil Capacity (vdih filter) 78 - 80 oz. (2.3 - 2.4 L) Engine End Cover Boll 220 lb -In (25Nm) ' 2Ok Watt. Displacement 60.60 ci. (993 cc) Bore 3.4051n. (86.5 mm) Stroke 3.366 In. (85.5 mm) Spark Plug Gap 0.020 in. (0.51 mm) Spark Plug Torque 180 lb -in. (20 Nm) Armature Air Gap 0.005 - 0.008 in. (0.13 - 0.20 mm) Intake Valve Clearance 0.004 - 0.006 in. (0.10 - 0.15 mm) Exhaust Valve Clearance 0.007 - 0.008 in. (0.15 - 0.20 mm) Oil Type 5W30 Synthetic Oil Capacity (with filter) 78 - 80 oz. (2.3 - 2.4 L) Engine End Cover Bolt 220 lb,4n (25Nm) BId system setup You must perform the following before operating the system: • If generator is installed in an area regularly subjected to temperatures below 40•F (4•C), select a 50 second warm up time by moving jumper JP2 (C) installed on transfer switch control board from '20' position to '50' position. Set the DPSW1 (A) and DPSW2 (B) dipswitches on the transfer switch control board to match the kW rating of the home standby generator, as described In Setting Dipswitches. /0/0 C7 M1 oa000uo CQ =:Je .,,s 1 ° Setting Dipswitches Dipswitches are used to adjust control board operation based on generator capacity. DPSW1 and DPSW2 switches are, set to correspond to total system kW rating. Dipswitch DPSWT..(A) has units of 1,000 watts; Dipswitch DPSW2 (B) has unit of 10,000 watts. Set dipswitches with power removed from the transfer switch to ensure proper control system operation. If dipswitches are set when power is present at transfer switch, a power reset needs to be performed before the new dipswitch settings will take effect. Power reset is when all power is removed from the transfer switch and then reintroduced after 30 seconds. NOTICE A transfer switch fault message will occur on standby generator control board if dipswitches are not properly established as noted above. To properly establish the dipswitches, make sure that only one dipswitch is set to "ON" position for DPSW1 and one dipswitch for DPSW2. For example a 20kW generator, set DPSW2 dipswitch 20 to "ON" position and DPSW1 dipswitch 0 to "ON" position. 20,000 plus 0 equal 20,000 watts. NONCE Use extreme caution when setting dipswitches or damage to control board will result. Use a pencil or small piece of plastic to set the dipswitch. NEVER use a screwdriver or any type of metal object to set dipswitches. The "On" position for the dipswitches 1s the switch number ON THE TRANSFER SWITCH CONTROL BOARD, not on the switch. For example, for an 18,000 watt generator, set DPSW2 dipswitch 10 to "On" position. Set DPSW1 dipswitch 8 to "On" position.10,000 plus $000 equals 18,000 watts. Set only one switch to "On" position on DPSW1 and DPSW2. Refer to following chart for proper switch selection(s). kW Rating of Generator ® OPSW 81 "ON" Position g OPSW #2 "ON" Position M 7 0 8kW s 0 90 9 0 10kW* 0 10 MW' :1 10 1M.. 2 10 13Wt ,, '= 3 10 14kW 4 10 16M 5 10 16kW 6 10 MIN 7 10 18kW 8 10 19kW 9 10 200 0 20 MIN 0 30 45kW 5 40 MW 8 40 MW 0 50 60M 0 60 • For genarat= sith a oft tW Includes 500 watts, =nd dw to next tomt rating (mmpk IM M eet to 13M NOTICE Air density is less at high altitudes, resulting in less available engine power. Specifically, engine power will decrease 3.5% for each 1.000 feet (300 meters) above sea level and 1% for each 10° F (5.6°C) above 77°F (250C). Generators located in these conditions must have the transfer switch programmed appropriately for this power decrease. 14 BRIGGSandSTRATTON.COM Automatic Transfer Switch Product Specfications Model 071US Series 100$ED Rated Maximum load Current a 25°C (770F)"..............................................................100 Amps Rated AC Voltage...............................................................250 Volts Poles............................................................................................... 2 Frequency................................................................................60 Hz Fault Current Rating ..........22,000 RMS symmetrical Amperes on ucny side .................................10,000 RMS Symmetrical Amperes on Generator side Normal Operating Range ...............-28.8°C (-20°F) to 40°C (104°F) Weight........................................................................13 kg (29 lbs) Model 071049 Series 200SED Rated Maximum Load Current a25°C (77°F)•..............................................................2(W ps Rated AC Voltage...............................................................250 Volts Poles........................................................................ «.:........... 2 Frequency..................................................... ............. ...GO Hz Fault Current Rating ..........25,000 RMS Symmetr[W'Ampem on utility Skle .................................10,000 RMS Symmetrio Amperes on Generator Sid$ Normal Operating Range ............. !,.-28.8T 209to 40°C �04° Weight .......................................... 4............................... 27 kg (59 ibs� Model 071068 ` Series 200SED Rated Maximum Load Current a25°C (77°F)'..............................................................200 Amps Rated AC Voltage...............................................................250 Volts Poles............................................................................................... 2 Frequency................................................................................60 Hz Fault Current Rating ..........25,000 RMS Symmetrical Amperes on Utility side ...............................10,000 RMS Symmetrical Amperes on Generator Side Normal Operating Range ............... -28.8°C (-20°F) to 40°C (104°F) Weight........................................................................27 kg (59 lbs) This transter switch is a UL Listed device. Model 071054 Series 200SED Rated Maximum Load Current a 25°C (770F)'..............................................................200 Amps Rated AC Voltage...............................................................250 Volts Poles............................................................................................... 2 Frequency................................................................................60 Hz Fault Current Rating ..........25,000 RMS symmetrtcal Amperes on My side .................................10,000 RMS Symmetrical Amperes on Gere3rator Side Normal Operating Range ...............-28.8°C (-20°F) to 40°C (104°F) Weight........................................................................27 kg (59 lbs) Model 071070 Series 200SED Rated Maximum Log, Current a25°C (77AE)'.:.0..........................................................150 Amps Rated AC Voltage...............................................................250 Volts Poles:...:.:....................................................................................... 2 Eraquepcy................................................................................60 Hz r Fault Current Rating ..........25,000 RMS Symmetrical Amperes on utlydy Side ................................... 10,000 RMS Symmetrical Amperes on Generator side Normal Operating Range ...............-28.8°C (-20°F) to 40°C (1040F) Weight........................................................................27 kg (59 lbs) Model 071071 Series 100SED Rated Maximum Load Current a25°C (77°F)'..............................................................100 Amps Rated AC Voltage...............................................................250 Volts Poles............................................................................................... 2 Frequency................................................................................60 Hz Fault Current Rating ..........22.000 RMS Symmetrical Amperes on Utility Side ................................. 10,000 RMS Symmetrical Amperes on Generator Side Normal Operating Range ...............-28.8°C (-20°F) to 40°C (104°F) Weight........................................................................13 kg (29 lbs) 24 BRIGGSandSTRATTON.COM