The URL can be used to link to this page

Home My WebLink AboutEvaluation ReportDIVISION: 06 00 00—WOOD, PLASTICS AND COMPOSITES SECTION: 0616 00—SHEATHING DIVISION: 07 00 00—THERMAL AND MOISTURE PROTECTION SECTION: 07 25 00—WATER-RESISTIVE BARRIERS/WEATHER BARRIERS jDo.��OFo SECTION: 07 27 00—AIR BARRIERS b 7�P'F REPORT HOLDER: HUBER ENGINEERED WOODS, LLC EVALUATION SUBJECT: ZIP SYSTEM"" WALL SHEATHING ICC ICC ICC "2014 Recipient of Prestigious Western States Seismic Policy Council (WSSPC) Award in Excellence" A Subsidiary of ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any of r e''�� s c t lly addressed, nor are they to be construed as an endorsement of the subject of the report or �redFtfan or its use. There is no warranty by iCC Evaluation Service, LLC, express or implied as to arty finding or other matter in this report, or as to any product covered by the report. eiow Copyright ® 2018 ICC Evaluation Service, LLC. All rights reserved. ICC-ES Evaluation Report ESR-1474 Reissued October 2018 This report is subject to renewal October 2020. www.icc-es.ora 1 (800) 423-6587 1 (562) 699-0543 A Subsidiary of the International Code Council® DIVISION: 06 00 00—WOOD, PLASTICS AND COMPOSITES Section: 0616 00--Sheathing DIVISION: 07 00 00—THERMAL AND MOISTURE PROTECTION Section: 07 25 OD —Water -resistive Barriers/Weather Barriers Section: 07 27 00--Air Barriers REPORT HOLDER: HUBER ENGINEERED WOODS, LLC EVALUATION SUBJECT: ZIP SYSTEM® WALL SHEATHING 1.0 EVALUATION SCOPE Compliance with the following codes: ■ 2015, 2012 and 2009 International Building Code (IBC) ■ 2015. 2012 and 2009 International Residential Code® (IRC) ■ 2015, 2012 and 2009 International Energy Conservation Cade (IECC) For evaluation of compliance with codes adopted by the Los Angeles Department of Building and Safety (LADBS), see ESR-1474 LABC and LARC Supplement. Properties evaluated: ■ Weather resistance ■ Air leakage 2.0 USES ZIP System Wall Sheathing panels are used as combination wall sheathing, air barrier, and water -resistive barrier. This report recognizes the use of ZIP System Sheathing, when installed with ZIP SystemThl flexible flashing seam tape, in walls of Type V construction (IBC) and dwellings under the IRC, and as an alternate to the water -resistive barrier required in Chapter 14 of the IBC and Chapter 7 of the IRC, and to the air barrier required by Sections R402.4 and C402.5.1 of the 2015 IECC (Sections R402.4 and C402.4.1 of the 2012 IECC; Sections 402.4.1 and 502.4.3 of the 2009 IECC). 3.0 DESCRIPTION 3.1 Sheathing Panel: The ZIP System Wall Sheathing panel is an OSB wood structural panel having a laminated exterior facer. The Exposure 1 OSB complies with US DOC PS 2 for wood structural panels. The exterior facer is a medium -density, phenolic4mpregnated, polymer -modified sheet material qualifying as a Grade D water -resistive barrier (required by Section 2510.6 of the 2015, 2012 and 2009 IBC). The panels are nominally 4 feet wide by 8, 9, 10. 11 or 12 feet long and have a square -finished -edge or machined -edge profile. When tested in accordance with ASTM E96 (water method), the polymer -modified sheet overlay has a minimum vapor permeance of 12 perms [68.6 X 10-11 kg/(Pa-s-m2)]. Equivalent Water Vapor Transmission rate (WVT) of the polymer -modified sheet overlay is 83.4 g/(24h-m2) when tested at 73.4°F (23°C). The water -resistive barrier and air barrier properties of the ZIP System® Wall Sheathing Panels are not affected when the panels are manufactured to comply as facing materials for SIPS in accordance with Section R610.3.2 and Table R610.3.2 of the 2015 IRC (Section R613.3.2 and Table R613.3.2 of the 2012 and 2009 IRC). 3.2 Seam Tape: The ZIP SystemThl seam tape is a self -adhering membrane tape consisting of acrylic adhesive laminated to a polyolefin backing. The tape is 0.012 inch (0.30 mm) thick with a minimum width of 3 /4 inches (95.2 mm), and comes in rolls of various lengths. 4.0 INSTALLATION 4.1 General: Installation of ZIP System® Wall Sheathing panels must comply with the applicable code, this report and the manufacturers published installation instructions. The manufacturers published installation instructions must be available at the jobsite during installation. 4.2 Application: 4.2.1 General: The ZIP System® Wall Sheathing panels must be attached to wall framing in accordance with the applicable code for wood structural panels, and in compliance with their panel span rating. The panels must be installed with the polymer -modified sheet overlay facing the exterior. In accordance with the manufacturers published installation instructions, it is recommended that the square edges of the panels be installed with a gap between adjacent panels and between panels and dissimilar materials. All ZIP Systeme Wall Sheathing panel seams must be sufficiently sealed with ZIP System seam tape. All overlay surfaces must be dry and free of sawdust and dirt prior to application of the ZIP System- seam tape. ICC-ES Evalmtion Reporu are not to be construedas representing aesthettcs or arty other atmthuts, not spec fmQy addressed, nor are they to be construed m m endomement ufthe subject of the repurt ora rero endation for its we. Thereis no warranry by ICC Evaluaaun Servtre, LLC, evpms or implied, as to mryftndingor uther matter in this report, or as to airy product morred by the report. copyright 0 2018 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 9 ESR-1474 I Most Widely Accepted and Trusted Page 2 of 9 The ZIP SystemT°" seam tape must extend a minimum of 1 inch (25.4 mm) past the panel edge T-joint intersections and must be centered within '/2 inch (12.7 mm) over the middle of panel seams. The tape must be pressed firmly to adhere to the surfaces and seal the seams. Wrinkles in the ZIP SystemTM seam tape are acceptable unless they create a leak path to the panel seam. 4.2.2 Flashing: Flashing complying with the applicable code must be installed at the perimeter of door and window assemblies, penetrations and terminations of exterior wall assemblies, exterior wall intersections with roofs, chimneys, porches, decks, balconies, and similar projections, and at built-in gutters and similar locations where moisture could enter the wall. An adhesive -backed flashing tape recognized in a current [CC -ES evaluation report must be installed to seal all ZIP System Wall Sheathing flashing joints. Penetration items must be sealed to the panels. The adhesive -backed flashing tape must comply with the ICC-ES Acceptance Criteria for Flexible Flashing Materials (AC148) and must be installed in accordance with the manufacturer's published installation instructions. See Figures 1 through 7 of this report for typical flashing, water -resistive barrier and air barrier assembly installation details. 4.2.3 Air Barrier Assembly: ZIP System Wall Sheathing fastened to maximum 24-inch-on-center (610 mm) wood wall framing, using minimum 6d nails spaced at 6 inches (152 mm) around panel edges and at 12 inches (305 mm) in the field, leaving a '/8-inch (3.18 mm) gap between panels, forms an air barrier assembly when the gaps between panels and the perimeter of penetrations are sealed with ZIP SystemT seam tape as required by Section 4.2.1. The assembly has demonstrated a maximum air leakage of 0.0072 cfm/ft2 [0.037 L/(s•m2)1 infiltration and 0.0023 cfrn/ft2 [0.012 L/(s•m2)] exfiltration at a pressure differential of 1.57 psf (75 Pa) when tested in accordance with ASTM E2357. 5.0 CONDITIONS OF USE The ZIP System Wall Sheathing panel and tape system described in this report complies with, or is a suitable alternative to what is specified in, those codes listed in Section 1.0 of this report, subject to the following conditions: 5.1 This evaluation report and the manufacturer's published installation instructions, when required by the code official, must be submitted at the time of permit application. 5.2 The ZIP System® Wall Sheathing panels must be manufactured, identified and installed in accordance with this report and the manufacturer's published installation instructions. In the event of a conflict between the instructions and this report, this report must govern. 5.3 The ZIP System Wall Sheathing panels must be covered with a code -complying exterior wall covering, or one that is recognized in a current ICC-ES evaluation report 5.4 The OSB sheathing must comply with US DOC PS-2. 5.5 Fire -resistance -rated construction is outside the scope of this report. 5.6 The Zip System Wall Sheathing panels are manufactured by Huber Engineered Woods, LLC, in Crystal Hill, Virginia; Easton, Maine; Commerce, Georgia; Broken Bow, Oklahoma; Spring City, Tennessee: and Shawinigan, Quebec Canada, under a quality -control program with inspections by ICC-ES. 6.0 EVIDENCE SUBMITTED 6.1 Data in accordance with the ICC-ES Acceptance Criteria for Water -resistive Membranes Factory - bonded to Wood -based Structural Sheathing, Used as Water -resistive Barriers (AC310), dated May 2008 (editorially revised August 2015). 6.2 Air leakage data in accordance with ASTM E2357. 7.0 IDENTIFICATION 7.1 Each ZIP System Wall Sheathing panel described in this report must bear a label that includes the manufacturers name (Huber Engineered Woods LLC), the product name, nominal panel thickness, the evaluation report number (ESR-1474), and the words "Mill 229, Crystal Hill, Virginia"; "Mill 228, Easton, Maine"; "Mill 227, Commerce, Georgia"; "Mill 290, Broken Bow, Oklahoma", "Mill 230. Spring City, Tennessee", or "Mill 390, Shawinigan, Quebec Canada." The OSB sheathing must also bear a label demonstrating compliance with US DOC PS 2 from an approved inspection agency. The ZIP System' seam tape roll must be labeled with the ZIP System logo and the evaluation report number ESR-1474 (see Figure 8). 7.2 The report holders contact information is the following: HUBER ENGINEERED WOODS, LLC ONE RESOURCE SQUARE 10925 DAVID TAYLOR DRIVE, SUITE 300 CHARLOTTE, NORTH CAROLINA 28262 (800)933-9220 www.huberwood.com ESR-1474 I Most Widely Accepted and Trusted 3of9 MMDE iNME �m MczS PGLMI ANE mjw wcI�EAMG C MG NEfA Mom BY FLASNMG 14WIh NRER FI/SNmmDP sWAIL SILL SECTION JAMB SECTION FIGURE 1—TYPICAL CROSS SECTIONS OF FLANGED WINDOW ESR-1474 I Most Widely Accepted and Trusted Page 4 of 9 � :,sma• wall �FATIx6 PLN♦71E-2WJRD P-lN` N4 L1PE Ftll(il F2WSE GLLUFS ION—AF9JnE PCJ�FSTHAIIE ILAfN Intro xuo = CUPIlIE Ca$ �tVTIMa'NFiD SILL SECTION HEADER SECTION WLNOOW JAMB ZP SYSTEM ADHESIVE —BACKED WALL SHEALHING FLASHING TAPE OUTSIDE CAULKING ROUGH OPENING INSIDE LOW—PRESOURE POLWRETHANE FOAM JAMB SECTION FIGURE 2—TYPICAL CROSS SECTIONS OF INSTALLED BRICK MOLD WINDOW ESR-1474 I Most Widely Accepted and Trusted Page 5 of 9 ZIP SYSTEMTM WALL SHEATHING WALL FRAMING ADHESIVE -BACKED FLASHING TAPE METAL FLASHING - FLASHING FASTENER ADHESIVE -BACKED FLASHING TAPE ROOF UNDERLAYMENT (FELT) / ROOF SHEATHING ROOF JOIST FIGURE 3-ROOF-WALL INTERSECTION (OPTION 1) FIGURE S—TYPICAL WALL -SILL INTERSECTION AND FLASHING DETAILS FOR BRICK SIDING ZIP SYSTEM T.M WALL SHEATHING WALLFRAMING ADHESIVE -BACKED FLASHING TAPE FLASHING FASTENER COUNTER FLASHING BASE FLASHING FLASHING FASTENER ADHESIVE -BACKED FLASHING TAFE �ROOF UNOERLAYNENT (FELT) i-ROOF SHEATHING ROOF JOIST FIGURE 4—ROOF-WALL INTERSECTION (OPTION 2) FIGURE 6—TYPICAL WALL -SILL INTERSECTION AND FLASHING DETAILS FOR LAPPED SIDING ESR-1474 I Most IMdelyAccepted and Trusted Page 6 of 9 Adhesive -Backed FIGURE 7—INSTALLATION AT PENETRATION OPENING (NON -FIRE -RESISTANCE RATED) FIGURE 8—LABELING FOR THE LP SYSTEM- SEAM TAPE ROLL IMES Evaluation Report ESR-1474 LABC and LARC Supplement Reissued October 2018 This report is subject to renewal October 2020. www.icc-es.org 1 (800) 423-6587 1 (562) 699-0543 A Subsidiary of the International Code Council® DIVISION: 06 00 00—WOOD, PLASTICS AND COMPOSITES Section: 06 16 OD —Sheathing DIVISION: 07 00 00—THERMAL AND MOISTURE PROTECTION. Section: 07 25 00—Water-resistive Barriersi eather Barriers Section: 07 27 00—Air Barriers REPORT HOLDER: HUBER ENGINEERED WOODS, LLC EVALUATION SUBJECT: ZIP SYSTEM® WALL SHEATHING 1.0 REPORT PURPOSE AND SCOPE Purpose: The purpose of this evaluation report supplement is to indicate that the ZIP System® Wall Sheathing, described in ICC-ES master evaluation report ESR-1474 has also been evaluated for compliance with the codes noted below as adopted by the Los Angeles Department of Building and Safety (LADES). Applicable code editions: ■ 2017 City of Los. Angeles Building Code (LABC) ■ 2017 City of Los Angeles Residential Code (LARC) 2.0 CONCLUSIONS The ZIP Systems Wall Sheathing, described in Sections 2.0 through 7.0 of the master evaluation report ESR-1474complies with the LABC Chapter 14, and the LARC Section R703, and is subject to the conditions of use described in this supplement 3.0 CONDITIONS OF USE The ZIP System Wall Sheathing, described in this evaluation report must comply with all of the following conditions: ■ All applicable sections in the master evaluation report ESR-1474. ■ The design, installation, conditions of use and identification are in accordance with the 2015 International Building Code® (2015 IBC) provisions noted in the master evaluation report ESR-1474. ■ The design, installation and inspection are in accordance with additional requirements of LABC Chapters 16 and 17, as applicable. This supplement expires concurrently with the master report, reissued October 2018. ICC-ES Evalwnon lleporm are nai to be comimed as represenbng aesihetas or any other aunbutes not specifically addressed, mram theyto be conamed as an endocremeni of the subject of the report are recammendutian for ite urc. There is no warranty by f('C Eiis aalion Service, LLC. express or Implied, as 'u to anyfinding or other matter in this reparp orm to airy pnnluct covered by the report Copyright ® 2018 ICC Evaluation Service, LLC. All rights resemed. Page 7 of 9 ICC-ES Evaluation Report ESR-1474 CBC and CRC Supplement Reissued October2018 This report is subject to renewal October 2020. www.icc-es.orq 1 (800) 423-6587 1 (562) 699-0543 A Subsidiary of the International Code Council® DIVISION: 06 00 00—WOOD, PLASTICS AND COMPOSITES Section: 06 16 00—Sheathing DIVISION: 07 00 00—THERMAL AND MOISTURE PROTECTION Section: 07 25 00—Water-resistive Barriers/Weather Barriers Section: 07 27 00—Air Barriers REPORT HOLDER: HUBER ENGINEERED WOODS, LLC EVALUATION SUBJECT: ZIP SYSTEM° WALL SHEATHING 1.0 REPORT PURPOSE AND SCOPE Purpose: The purpose of this evaluation report supplement is to indicate that ZIP System® Wall Sheathing, recognized in ICC-ES master evaluation report ESR-1474, has also been evaluated for compliance with the codes noted below. Applicable code editions: ■ 2016 California Building Code (CBC) ■ 2016 California Residential Code (CRC) 2.0 CONCLUSIONS 2.1 CBC The ZIP System® Wall Sheathing, described in Sections 2.0 through 7.0 of the master evaluation report ESR-1474, complies with CBC Chapter 14, provided the design and installation are in accordance with the 2015 International Building Code (2015 IBC) provisions noted in the master report and the additional requirements of the CBC Chapters 14, 16, 16A, 17, 17A and 23, as applicable. 2.2 CRC The ZIP System® Wall Sheathing, as described in Sections 2.0 through 7.0 of the master evaluation report ESR-1474 complies with the CRC, provided the design and installation are in accordance with the 2015 International Residential Code (2015 IRC) provisions noted in the master report. The ZIP System® Wall Sheathing recognized in this supplement has not been evaluated for compliance with the International Wildland-Urban Interface Code". This supplement expires concurrently with the master report, reissued October 2018. ICC-ES Evaluation Reports arc not to be cmrzuved m ri prnemnigaertheticr or any other atmbutes not spec fwily addressed, norms, they to be construed os an eadonemear of the subject of the report or a mcommendmton jar its use. There is no warranty by IC'C Evaluation Service, LLC express or implied, as Z to anyfnding or other miter in this report, or m to anypruduct covered by the mpon. Copyright® 20181CC Evaluation Service, LLC. All rights reserved. Page 8 of 9 ICC-ES Evaluation Report ESR-1474 FBC Supplement Reissued October2018 This report is subject to renewal October 2020. www.icc-es.org 1 (800) 423-6587 1 (562) 699-0543 A Subsidiary of the International Code Council® DIVISION: 06 00 00—WOOD, PLASTICS AND COMPOSITES Section: 06 16 OO—Sheathing ' DIVISION: 07 00 00—THERMAL AND MOISTURE PROTECTION Section: 07 25 00—Water-Resistive BarrierslWeather Barriers Section: 07 27 00—Air Barriers REPORT HOLDER: HUBER ENGINEERED WOODS, LLC EVALUATION SUBJECT: ZIP SYSTEM® WALL SHEATHING 1.0 REPORT PURPOSE AND SCOPE Purpose: The purpose of this evaluation report supplement is to indicate that ZIP System Wall Sheathing panels, recognized in ICC-ES master evaluation report ESR-1474, have also been evaluated for compliance with the codes noted below. Applicable code editions: ■ 2017 Florida Building Code —Building. ■ 2017 Florida Building Code —Residential 2.0 CONCLUSIONS The ZIP System® Wall Sheathing panels, described in Sections 2.0 through 7.0 of the master evaluation report ESR-1474, comply with the Florida Building Code —Building and the Florida Building Code —Residential, provided the design and installation are in accordancewith the 2015 International Building Code provisions noted in the master report. Use of the ZIP System Wall Sheathing panels for compliance with the High -Velocity Hurricane Zone provisions of the Florida Building Code —Building and the Florida Building Code —Residential has not been evaluated, and is outside the scope of this evaluation report. For products falling under Florida Rule 9N-3, verification that the report holder's quality assurance program is audited by a quality assurance entity approved by the Florida Building Commission for the type of inspections being conducted is the responsibility of an approved validation entity (or the code official, when the report holder does not possess an approval by the Commission). This supplement expires concurrently with the master report, reissued October 2018. XC-ES Evaluation Reports are nut robe construed as ®presenting aesthetics or any other attributes not specifically addressed nor are they to be construed man endarsement of the subject of the report or a recommendation fur its use. Thee,., on x armnry by lC'C' Evalumma Service, LLC. esp. or otphod, ar Y to anyftnding or other matter in this report, or m to any product covered by the report Copyright® 20181CC Evaluation Service, LLC. All rights reserved. Page 9 of 9