Press Alt + R to read the document text or Alt + P to download or print.
This document contains no pages.
HomeMy WebLinkAboutEngineering P1
i�
F I L!o T A ENGINEERING & TESTING, INC.
Phone: (866)781-6889-Fax: (866)784-8550
www.floridaengiueeiingantltesting.com
250 S.W.13t1`Avenue
Pompano Beach,FL 33069
August 25,2020 Job Order No.: 20-3383
Permit No.: 1801-0658
Joseph Callejo
18707 Tranquility Base Lane
Port St.Lucie,Florida ,
RE: TAS-106 TILE UPLIFT TESTS
Proposed Roof
Callejo Residence
18707 Tranquility Base Lane
Port St.Lucie,Florida
Dear Sir or Madam:
In accordance with your authorization, Florida Engineering & Testing Inc., has
performed Tile Uplift Testing in compliance with Testing Application Standards TA.S-
106 and the Florida Building Code High Velocity Hurricane Zone on August 21,2020, at
the above referenced project.
The purpose of our inspection was to determine the uplift capacity of the roof tiles for the
above referenced project. The subject roof consisted of clay barrel tile nail set. The pitch
of the subject roof is 5/12.
Our field engineer's representative visited the site and conducted fifteen (15) uplift tests
on the roof tiles. All tests were performed according to the Florida Building Code High
Velocity Hurricane Zone and protocol TAS-106 using an Intercomp scale model CS200.
The following is a summary of results:
Field Test Results
Test Number Test Location Field Uplift Pull Test Test
Result
1 - 3 Corner See Attached Diagram 35 f 5 pounds Passed
4- 9 Perimeter See Attached Diagram 35 f 5 pounds Passed
10 - 13 Field See Attached Diagram 35 t 5 pounds Passed
14 - 15 Rid e&Hip See Attached Di a am 35 f 5 pounds Passed
Ll
Q
Qrcaht� ,���rA��/.b[ss�ci tt��ce
Page 2
August 25,2020 Job Order No.20-3383
Joseph Callejo
Callejo Residence
18707 Tranquility Base Lane
Port St.Lucie,Florida:
All test results were found to be in compliance with TAS-106 and the Florida Building
Code(see attached field sketch).
The test results are limited to the tested areas. If other roof areas exhibit different
conditions, it should be brought to our attention for remedial work. This uplift test is not
a final roof inspection. A final roof inspection must be conducted by the building official
for approval.
The test results presented reflect the condition of the roof system at the time of the test.
These results are time and sample dependent since roof conditions are continuously
changing due to exposure to the elements.
Florida Engineering & Testing, Inc. (FE&T) is an independent third parry providing un-
biased testing information and results. FE&T is not affiliated with our client nor do we
have any financial interest in the project or determination of the test results.
As mutual protection to clients, the public and ourselves, all reports are submitted as the
confidential property of clients, and authorization for publication of statements,
conclusions or extracts from or regarding our reports is reserved pending our written
approval.
Florida Engineering&Testing,Inc., appreciates the opportunity to be of service to you at
this phase of your project. If you have any questions or comments, please give us a call.
We would be pleased to help in any way we can. It has been a pleasure working with you
and look forward to doing so again in the near future.
Sincerely,
S
G '-
-Wo
lurk A. Mesiaho P.E. _
FI'fli'fda Enein &Ti g,Inc.
Fld�;id Tteg,-No.apizAidn
gb'2��
Certi'fi ate gf�A No. 6923
- � E
s
_LL
31
t , J
19,
[Approximate
ield Sketch-Not to Scale
a=0.1W=0.1 x 19=1.9' Dimensions
a=0.4H=0.4 x 15=6'
Perimeter Dimensions=3' 8707')Gran uili#y Base Ln
ort St.Lucie,Florida
u
Table 7: Attachment Resistance Expressed as a Moment- Mf(ft-lbf)
for Mortar Set Systems
Tile Tile Attachment
Profile Application Resistance
Medium Profile Concrete Tile Mortar Set' 20.60
9 Tile-rite Roof Tile Mortar-
S. LABELING
All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo (See
Detail Below),or following statement: "Miami Dade County Product Control Approved".
RECEIVED
I
JUN 17 2020 �-�
Permitting Department
St. Lucie County EAGLEI,,
nen'
�FI '
LoRiDA
i
(LOCATED ON UNDU SWE OF TII.E)
I
OR
EAGLE FL
(LOCATED ON FRONTSIDE OF TILE)
I
MEDIUM PROFILE_CONCRETE ROOF TILE LABEL,S'UMTERVILLE PLANT
NOA No.18-0509.19
it Fnoof cout�rr Expiration Date: 10/05/21
Approval Date: 06/14/18
Page 6 of 7
r
6. BumDjNG PERmrr REQu1REM ENTS:
6.1 Application for building permit shall be accompanied by copies of the following:
6,1,1 This Notice of Acceptance.
61.2 Any other documents required by AHJ or applicable Building Code in order to properly evaluate the
installation of this system
i
PROFIImE DRAwiNG
i
i
F u .'
I
I '
I 4
AUDIum PRom ZE CoNcR,=RooF TILE
END of TMS ACCEPTANCE
i
i
I
NOA No.18-0509.1.9
MIAMFDAflECou Expiration Date: 10/05/21
Approval Date: 06114/18
Page 7 of 7
EXTERIOR RESEARCH&DESIGN,I.I.C.
0 Certificate of Autholizadon#9503
TRRINI ��� 353 CfIRISTIAN STREET,UNIT#13
QIOXFORD,CT 05478
(203)262-9245
;EVALUATION REPORT
Eagle Roofing Products Florida I.I.C. Evaluation Report E1322.09.06-115
1575 East;Country Road 470 FL7473-RB
Surnterville,FL 33585 Date of Issuance:02/2412009
(800)4004245 Revision 5:10116/2017
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials.in the State of Florida.The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 6vr Edition (2017) Florida Building Code
1 (NON-HVHZ)sections noted herein.
DESCRIPTION: Eagle Roof Tiles
LABEuNs: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED CompuANCE: This Evaluation Report is valid until such time as the named product(s)changes,the referenced
Quality Assurance documentation changes,or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product
changes or the referenced Quality Assurance documentation changes. Trinity0 ERD requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
AovERnsEMENT:The Evaluation Report number preceded by the words"Evaluated by Robert Nieminen, P.E." may be
displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its
entirety. .
INSPEcTIoN:Upon request,a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 5.
Prepared by: ,.,�"�i�►r,,,w,,�--
Robert3.M.Nieminen,P.E. ?'=4 _-•-' =""
• �::15-�.:�,- Z:��:• 'Ihefacvrae seal appearingwasauthomedby Robert Merninen,
Florida Registration No.59166,Florida DCA ANEM3 '�. r'•- R'�'' P.EonW/16/=7_This does not serve as anelearoni
ollysigned
domtmerrL Signed,sealedha dmpiesl®vebeenvansmittedWthe
ProduUApprovalAdmM5fta[or and to the named dent
CEIMFIrAMCIN OF INDEPENDENCE:
1. TrinitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinity l ERD is not owned,operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen,P.E.does not have nor will acquire,a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
i
4. Robert Nieminen,P.E.does not have,nor will acquire,a financial interest in any other entity involved in the approval process of the
product
5. This is a building code evaluation. Neither TrinitylERD nor Robert Nieminen, P.E.are,in any way,the Designer of Record for any
project on which this Evaluation.Report,or previous versions thereof,Wwas used for permitting or design guidance unless retained
specifically for that purpose.
TPJNITYIERD
ROOFING SYSTEM EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Roofing Tiles
Compliance Statement: Eagle Roof Tiles,as produced by Eagle Roofing Products Florida LLC,have demonstrated
compliance with the following sections of the le Edition(2017)Florida Building Code(NON-13VHZ)through testing
in accordance with the following Standards. Compliance is subject to the Installation Requirements and limitations J
Conditions of Use set forth herein.
j 2. STANDARDS:
Section Property Standard Year
15073.5,R9053.5 Physical Properties ASTM C1492 200312009)
1507.3.7,R905.3.7 Attachment Requirements FRSAJTRI April 2012(04-12) 2012
1504.2.1.1 Overturning Moment SSIFD 11 1997
3.. REFERENCES:
Enti Examination Reference Date
ATL(TSf 3782) ASTM C1492 RT0310.01-17,02-17,03-17 03/35/2017
ATL(TST 3782) ASTM C1492—Freeze/thaw RT0706.01-17,02-17,03-17 09/25/2017
i Tile Roof Institute SSTD 11 Membership Letter 11/29/2005
ATI(QUA 1844) Quality Assurance Inspection Report 05/07/2017
4. PROD=ElFsoupnON:
4.1 �ASTM C2492,Type III(Low Profile): BEiAlR
73)
e
:d
I
I
G
1an7.
Exterior Research and Design,LLC. 6"'EDITION(2017)FSC NON-HVHZ EVALUAMON Evaluation Report E3322.09.06-115
CerhTicaWofauthorizarfon#9503 Eagle Roofing Products Florida LLL;1800)4003Z45 FL7473-RS
Revision 5:1011612M7
Page 2 of 3
TRINITY I ER®
4.2 ASTM C*92;.Type 1.1(Medium Profile); MAusu
aaau.
i alines
o .
o
i
12W
4.3 ASTM C1492,Type 1(High profile): CAPISTRANo
auamu
�az3r°
S, LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinitylERD nor Robert Nieminen, P.E. are, in any way, the
' Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 fire classification is not part of this evaluation; refer to FBC 1505.2, Exception 2 {for non-combustible .
deck)or listing by an approved testing agency for fire rating of this product
5.4 Lnderlayment shall be that which holds Florida Product Approval for use with file roofing systems. The
underlayment Product Approval shall specify allowable method(s) of the installation (mechanical
attachment, mortar-set and/or adhesive-set)for use with the specific underlayment. For mortar-set or
adhesive-set file roofing applications, the underlayment Product Approval shall specify attachment
methods for the underlayment system to resist wind uplift design loads in accordance with Table 1A of
FRSA/TR1 ApAl 2O12(04-12).
5.5 "Color-Bonded" or"Slurry-Coated"files are limited to use on projects in areas subjected to weathering
indices of 50 or less(negligible weathering),as outlined in Figure 1 of ASTM C1492-03(2009),reproduced
below for reference. This limitation does not apply to the"Color-Through"product offering.
- 50 '
- 50
50
WEATHERING REGIONS
F.-e_-.-1NEGLIGI8LE WEATHERING
MODERATE WEATHERING
SEVERE WEATHERING
5.6 All products in the roof assembly shall have quality assurance audit in accordance with IFAC Rule 6162O-3.
EAtefaor Research and Design,LLC. 6'H EDITION(2017)MC NO -HVIIz EVA9ADAMON Evaluation Report E3322.0%1)6-RS
certificate o/Aumoraation 99503 Eagle Roofing Products IAlodda LLC.;(800)400-3245 FL7473-R8
Revision S.10/15/2027
Page 3 of S
QO-rRINITYIERD
6. 1INSTALLAMON:
6.1 Eagle Roof Tiles may be mechanically fastened,mortar-set or adhesive-set. Installation shall comply with
manufacturer's current published instructions, but not less than the requirements of FBC 1507.3 and the
FRSA/TRI Florida High end Concrete and Clay Tile Installation Manual.
6.2 Underlayment shall be installed in accordance with FRSAJTRI April 2012 (04-22) or the underlayment
manufacturers current Product Approval. For mortar-set or adhesive-set file roofing applications, the
underlayment current Product Approval shall specify attachment methods for the underlayment system to
resist wind uplift design loads in accordance with Table 1A of FRSA/TRI April 2012(04-12).
6.3 Tile Attachment:
6.3.1 Mechanically Attached Tile:
Wind load resistance shall be in accordance with Table 3 of FRSA/TRI April 2012(04-12)to resist the Uplift
Moment determined in Table 2A or 26 of FRSAJTRI April 2012{04-12)or FBC 1609.5.3.
6.3.2 Mortar-Set Tile:
Wnd load resistance shall be in accordance with Table 2A or 213 of FRSA/TRI April 2012 (04-12)or,FBC
2609.5.3 in conjunction with the mortar manufacturer's Product Approval.
6.3.3 Adhesive-Set Tile:
Wind load resistance shall be in accordance with Table 2A or 2B of FRSA/TRI April 2012(04-12) or FBC
1609.5.3 in conjunction with the adhesive manufacturer's current Product Approval. Refer to the current
version of the referenced Florida Product Approval for paddy-placement details and performance data.
TILE ADHESIVES FOR R ADHESIVE-SErT1LE SYsTEms
Manufacturer Products Florida product Approval
'Touch N'Seal Storrs Bond" FL14506
DAP Foam,Inc.
i
`?ouch N'Seal Storm Bond 2" FL21374
Dow Chemical 'TILE BOND—' FL22-525
"Polyset®AH-160" FL6332
1CP Adhesives&Sealants,Inc
"Polyset®RTA-in 1=L5276
6.3.4 HiD and Ridge T le:
Tile shall be installed in accordance with FRSAJTRI April 2012(04-12). For hip and ridge tile installations
atop hip and ridge metal,refer to the hip and ridge metal,manufacturer's current Product Approval(e g.,
FL5374) or test report in accordance with SSTD 11 for allowable loads to resist those determined in
accordance with Table 1A of FRSAJTRI April 2M2(04-22).
Exterior Research and Design,LLC. EDITION(2017)FSC NON-HVHZ EVALUATION Evaluation Report E3322-09.06-115
Certificate ofauthoriration 99503 Eagle Roofing Products Florida LLC.,(BDD)40D-3245 FL7473-RB
Revision 5:10116POI7
Page 4.of 5
it RINI lW I ERR
7. LABEUNG:
7.1 Each unit shall bear the imprint or identifiable marking of the manufacturer's name or logo. Tile lots shall
be labeled in accordance with the requirements of the Accredited Quality Assurance Agency noted.herein.
EArGLEI.
0
F
i
LoRiDA EAGLE FL
(t.DCA=01 U-N DMISMI:OF F (LOCATED 01A' E11;MUS I + E OF TILE)
7.2 Tile not tested for freeze-thaw shall state clearly that the lot has not been tested for freeze thaw
acceptance on all lot tags or certification.
8. Bu1LD1NG PERMIT REQu1REMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING'PLANTS:
I
Sumterville,FL
10. QUAUTY ASSURANCE ENTITY.-
Architectural Testing,Inc.—QUA1844;(717)764-7700
-END OF EVALUATION REPORT-
ASTM C1492-03,Standard Specification for Concrete Roof Tile,©AS TM International
I
Exterior Research and®esigra,U.C. 6""EDITION Q2037)FEC IMON-HUM EVAL2DAMON Evaluation Report E1322.09.06-R3
Lerr+fitote ofAUthmfttinn R9503 Eagle Roofing Products Florida UC—;1800)40D-3245 F17473-R8
j Revision 5:10/16J2017
Page 5 of 5