HomeMy WebLinkAboutProduct evaluation report, underlayments intertek
Total Quality.Assured.
KIRSCH BUILDING PRODUCTS
PR00-),, UC(--,4,T E1J,1ALUAM0P\1-\
SCOPE OF WORK
SHARKSKIN ROOF UNDERLAYMENTS
PRODUCT EVALUATION PER CHAPTER 61G20-3.005(2)(B) FLORIDA ADMINISTRATIVE CODE
REPORT NUMBER
15402.01-122-34-RO
FL8097-R5
ISSUE DATE
06/20/18
PREPARED BY
ARCHITECTURAL TESTING, INC. (INTERTEK-ATI)
FL COA 29274
lzxi i
REPORT ISSUED TO
KIRSCH BUILDING PRODUCTS, LLC
1464 Madera Road \��gtttttt�llfill/u//,��
Suite N-387 E. T/L�q
Simi Valley,CA 93065 C-�.•��C F ?
fir:
No. 73227
PAGES
7
�0•• STATE OF .JJJ
iT A
�'•.lpRtOPG���`
For INTERTEK B&C: ��1lnilnttN
PREPARED BY: Daniel C. Culbert, P.E. PREPARED BY: Gary Hartman, P.E.
=.TITLE]- TITLE
•Senior Project Engineer Laboratory
� Support Engineer
SIGNATURE:
DATE: ; 06/20/18 DATE: 06/20/18
GH:dc
I
i
I
intertek 130Derry 7406
York,Pennsylvania 1406
Total Quality.Assured. Telephone: 717-764-7700
Facsimile: 717-764-4129
www.intertek.com/building
PRODUCT EVALUATION REPORT FOR KIRSCH BUILDING PRODUCTS
Report No.: 15402.01-122-34-RO
Date:06/20/18
SECTION 1
SCOPE
Product Evaluation per Chapter 61G20-3.005(2)(b) Florida Administrative Code,
Evaluation report from a Florida Registered Architect or a licensed Florida Professional Engineer.
Product Category: ROOFING
Sub-Category: UNDERLAYMENT
Product:SHARKSKIN ROOF UNDERLAYMENTS
SECTION 2
BUILDING CODE COMPLIANCE
This product has demonstrated compliance with the intent of the Florida Building Code,
Building, 6th Edition (2017),Section 1507.1.1, Underlayment.
SECTION 3
PERFORMANCE STANDARDS
STANDARD TITLE
ASTM D226-09 Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing
and Waterproofing
ASTM D1970-15a Standard Specification for Self-Adhering Polymer Modified Bituminous
Sheet Materials Used as Steep Roofing Underlayment for Ice Dam
Protection
TAS 103-95 Test Procedure for Self-Adhered Underlayments for Use in Discontinuous
Roof Systems
SECTION 4
PRODUCT DESCRIPTIONS
Mechanically Fastened Underlayments
Sharkskin Comp® is a multi-layer laminated roof underlayment comprised of a high-strength
woven polypropylene scrim with a UV&antioxidant protection bond layer and a slip-resistant top
layer.
Sharkskin Ultra® is a multi-layer laminated roof underlayment comprised of a high-strength
woven polypropylene scrim with a UV & antioxidant protection bond layer to both sides and a
slip-resistant top layer.
Sharkskin Ultra Radiant® is a multi-layer laminated roof underlayment comprised of a high-
strength woven polypropylene scrim with a reflective barrier on the underside and a UV &
antioxidant protection bond layer on both sides and a slip-resistant top layer.
Page 2 of 7
0
to torte k 130 Derry Court
York,Pennsylvania 17406
Total Quality.Assured.; Telephone: 717-764-7700
Facsimile: 717-764-4129
www.intertek.com/buflding
PRODUCT EVALUATION REPORT FOR KIRSCH BUILDING PRODUCTS
Report No.:15402.01-122-34-RO
Date:06/20/18
Self-Adhering Underlayment:
Sharkskin Ultra SA® is a multi-layer laminated roof underlayment comprised of a high-strength
woven polypropylene scrim between two layers of UV&antioxidant protection bond and a self-
adhering underside and a slip-resistant top layer.
SECTION 5
INSTALLATION
General
1. Installation shall be in accordance with the manufacturer's installation instructions and
requirements for reinforced synthetic underlayments in §1507.1.1 for an alternative to
underlayment complying with ASTM D226 Type II and§1507.3.3.
2. Sharkskin roofing underlayment is considered a vapor barrier and should generally be
installed above ventilated attic spaces.
3. Damaged roof decking must be replaced.The roof deck surface must be dry and free of
dust, dirt,debris,grease,solvents, loose nails,and other protrusions.
4. Metal cap nails shall be required where the ultimate design wind speed, Volt, equals or
exceeds 150 mph.
Sharkskin Comp®
1. For plywood or wood plank, attach to the roof deck with corrosion-resistant steel ring
shank fasteners with a minimum shank diameter of 0.083 inches, having 1-inch diameter
corrosion resistant metal round cap, tin tag, or plastic round top caps or plastic caps
fastened with corrosion resistant staples.
2. For slopes 2.5:12 (11.8°)to 3.5:12 (16.2°): Sharkskin Comp shall be applied in a double
coverage method, with 25-inch minimum horizontal laps and minimum 6-inch vertical
laps offset by 6 feet. Fasten with two staggered rows in the field of the sheet with a
maximum fastener spacing of 12 inches and one row at the end and side laps fastened
6 inches o.c.
3. For slopes 3.5:12 (16.2')or greater: Sharkskin Comp shall be laid horizontally, parallel to
the eave with the printed side up,and have minimum 4-inch horizontal laps and minimum
6-inch vertical laps offset by 6 feet. Fasten with three staggered rows in the field of the
sheet with a maximum fastener spacing of 12 inches and one row at the end and side laps
fastened 6 inches o.c.
4. See manufacturer instructions at www.sharkskin.us for additional requirements.
Sharkskin Ultra®
1. For plywood or wood plank, attach to the roof deck with corrosion-resistant steel ring
shank fasteners with a minimum shank diameter of 0.083 inches, having 1-inch diameter
corrosion resistant metal round cap, tin tag, or plastic round top caps or plastic caps
fastened with corrosion resistant staples.
2. For steel deck, attach to the roof deck with approved corrosion resistant #10, #12 or
#14 screws and metal stress plates.Screws shall engage the top flute of the steel deck.
3. For slopes 2.5:12(11.8°)to 3.5:12(16.2°),otherthan tile: Sharkskin Ultra shall be applied
in a double coverage method,with 25-inch minimum horizontal laps and minimum 6-inch
Page 3 of 7
130 Derry Court
ntertek York,Pennsylvania 17406
Total Quality.Assured., Telephone: 717-764-7700
Facsimile: 717-764-4129
www.intertek.com/building
PRODUCT EVALUATION REPORT FOR KIRSCH BUILDING PRODUCTS
Report No.: 15402.01-122-34-RO
Date:06/20/18
vertical laps offset by 6 feet. Fasten with two staggered rows in the field of the sheet with
a maximum fastener spacing of 12 inches and one row at the end and side laps fastened
6 inches O.C.
4. For slopes 3.5:12 (16.2°) or greater, other than tile: Sharkskin Ultra shall be laid
horizontally, parallel to the eave with the printed side up, and have minimum 4-inch
horizontal laps and minimum 6-inch vertical laps offset by 6 feet. Fasten with three
staggered rows in the field of the sheet with a maximum fastener spacing of 12 inches
and one row at the end and side laps fastened 6 inches o.c.
5. See manufacturer instructions at www.sharkskin.us for additional requirements.
Sharkskin Ultra Radiant®
1. For horizontal battens,slopes 3:12 (14°) or greater:
a. Attach to the roof deck with corrosion-resistant steel ring shank fasteners with a
minimum shank diameter of 0.083 inches, having 1-inch diameter corrosion
resistant metal round cap, tin tag, or plastic round top caps or plastic caps
fastened with corrosion resistant staples.
b. For slopes 3.5:12 (16.2°) or greater: Sharkskin Ultra Radiant shall be laid
horizontally, parallel to the eave with the printed side down, and have minimum
4-inch horizontal laps and minimum 6-inch vertical laps offset b 6 feet. Fasten
P P Y
with three staggered rows in the field of the sheet with a maximum fastener
spacing of 12 inches and one row at the end and side laps fastened 6 inches o.c.
2. For counter battens,slopes 3:12(14°)or greater:
a. Attach to vertical battens with corrosion-resistant steel ring shank fasteners with
a minimum shank diameter of 0.083 inches, having 1-inch diameter corrosion
resistant metal round cap, tin tag, or plastic round top caps or plastic caps
fastened with corrosion resistant staples.
b. Sharkskin Ultra Radiant shall laid horizontally, parallel to the eave with the
printed-side-up across vertical wood, metal or plastic battens installed over a
solid deck spaced maximum 24" o.c. with minimum 4-inch horizontal laps and
minimum 6-inch vertical laps. Horizontal laps shall be sealed with Eternabond
Tape, butyl-based tape or other material specifically approved by Kirsch Building
Products. Vertical laps shall be minimum 6-inch wide and shall break over a
vertical batten to allow water to run away from the vertical batten. Sharkskin
Ultra Radiant shall be attached to the vertical battens sufficiently to hold in place
until the horizontal battens are installed over-top in accordance with the tile,
metal or slate manufacturer's requirements. The positioning of the fasteners
holding the Sharkskin Ultra Radiant to the vertical battens prior to placement of
horizontal battens shall not interfere with true, flush installation of horizontal
battens.
3. See manufacturer instructions at www.sharkskin.us for additional'requirements.
Page 4 of 7
c 130 Derry Court
ntertek York,Pennsylvania 17406
Total Quality.Assured. Telephone: 717-764-7700
Facsimile: 717-764-4129
www.intertek.com/building
PRODUCT EVALUATION REPORT FOR KIRSCH BUILDING PRODUCTS
Report No.: 15402.01-122-34-RO
Date:06/20/18
Sharkskin Ultra SA®
1. Adhere directly to the plywood deck orto a mechanically attached Sharkskin Ultra anchor
sheet for 2-ply system installation.
2. Position Sharkskin Ultra SA horizontally, parallel to the eave of the roof with the printed
side up with minimum 2-inch horizontal laps and minimum 6-inch vertical laps.
3. Pull away the split-release liner film backing and applying the underlayment to the
substrate.
4. Broom the entire surface of the underlayment, and use a heavy roller on all seams/laps
to establish a secure bond.
5. For nail-on tile: install per manufacturer's recommendations and FBC§1507.3.3.
6. For foam-on tile:
a. Back-nail the top horizontal edge of each run prior to placement of the
subsequent run. Back-nail to the roof deck with corrosion-resistant steel ring
shank fasteners with a minimum shank diameter of 0.083 inches, having 1-inch
diameter corrosion resistant metal round cap or approved tin tag. Back nail at
12 inches o.c. on side laps and 6 inches o.c. on end laps. No nails or tin caps shall
be exposed
b. For 2-ply system:the maximum fastener spacing in the field ofthe Sharkskin Ultra
sheet shall be 10 inches o.c.
7. See manufacturer instructions at www.sharkskin.us for additional requirements.
SECTION 6
LIMITATIONS OF USE
1. Fire Classification is not addressed by this Evaluation Report.
2. Use in the High Velocity Hurricane Zone is not addressed by this Evaluation Report.
3. Sharkskin Roof Underlayments shall not be exposed to sunlight for longer than:
a. Sharkskin Comp°: 180-days after installation.
b. Sharkskin Ultra®,Sharkskin Ultra Radiant°and Sharkskin Ultra SA°:
360 days after installation
Page 5 of 7
i
' J
intertek 130 Derry Court
York,Pennsylvania 17406
Total Quality.Assured.: Telephone: 717-764-7700
Facsimile: 717-764-4129
www.intertek.com/building
PRODUCT EVALUATION REPORT FOR KIRSCH BUILDING PRODUCTS
Report No.: 15402.01-122-34-RO
Date:06/20/18
4. Sharkskin Roof Underlayments may be used with roof coverings as follows:
Wood
Asphalt Nail-on i; Foam-on 1 shakes&
( Product Shingles Tile Tile Metal Shingles Slate
Comp® Y N N Y Y N
Ultra® Y Y1 Y1 Y Y Y
Ultra Radiant® YZ N N Y3 Y3 Y3
Ultra SA® Y Y Y4 Y Y Y
1. As the anchor sheet in a 2-ply system
2. Contact Kirsch Building Products for installation information.
3. With battens only
4. Foam-On Tile is limited to use with ICP Adhesives & Sealants, Inc. 2-Component Foam Roof Tile Adhesive
AH-160(FL6332),Dow TILE BOND"Roof Tile Adhesive(FL717)or DAP Foam, Inc.Touch 'n Seal Stormbond Roof
Tile Adhesive(FL14506).The maximum negative design pressure for such installations is-52.5 psf when adhered
directly to the plywood deck,and the lesser of-52.5 psf and the allowable uplift resistance of the mechanically
attached anchor sheet per§1507.3.3 for 2-ply installation.These pressures include a safety factor of 2.
SECTION 7
SUPPORTING EVIDENCE
Test Reports
G7683.01-109-18(TAS 103-95)
Issued:05/05/17
Architectural Testing, Inc.York, PA(TST1558)
Joseph A. Reed, PE (FL PE 58920)
JX06F8A(ASTM D1970-17a)
Issued:06/07/2018
Momentum Technologies International (TST2508)
John Nevin, PE(FL PE 54666)
JX17A7A(TAS 103-95)
Issued: 12/28/17
Momentum Technologies International(TST2508) DBA RCMA
John Nevin, PE(FL PE 54666)
JX17A7C(ASTM D226-17)
Issued: 12/28/17
Momentum Technologies International(TST2508) DBA RCMA
John Nevin, PE(FL PE 54666)
JX17A7D (ASTM D226-09)
Issued:05/11/17
Momentum Technologies International(TST2508) DBA RCMA
John Nevin, PE(FL PE 54666)
Page 6 of 7
I
Intertek 130Derry Court
7406
York,Pennsylvania 1406
Total Quality.Assured.; Telephone: 717-764-7700
Facsimile: 717-764-4129
www.1ntertek.com/building
PRODUCT EVALUATION REPORT FOR KIRSCH BUILDING PRODUCTS
Report No.: 15402.01-122-34-RO
Date:06/20/18
SECTION 8
CERTIFICATION OF INDEPENDENCE
In accordance with Rule 61G20-3.009 Florida Administrative Code, Intertek-ATI hereby certifies
the following:
• Intertek-ATI does not have, nor will it acquire, a financial interest in any company
manufacturing or distributing products for which this report is being issued.
• Intertek-ATI is not owned, operated or controlled by any company manufacturing
or distributing products for which this report is being issued.
• Gary Hartman, P.E. does not have nor will he acquire, a financial interest in any
company manufacturing or distributing products for which evaluations are issued.
• Gary Hartman, P.E does not have, nor will he acquire, a financial interest in any
other entity involved in the approval process of the product.
SECTION 9
REVISION LOG
REVISION#'- DATE PAGES REVISION
0 06/20/18 N/A Original Report Issue
Page 7 of 7