HomeMy WebLinkAboutNOA, Modified bitumen Tie r�c1
MIAMI-
j MIAMI-DADS COUNTY
MISSiJ� r=` 7 PRODUCT CONTROL SECTION
11805 SW 26 Street,Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) Miami,Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T(786)315-2590 F(786)31525-99
NOTICE OF ACCEPTANCE (NOA) www.niianddade.gov/economy
CertaiuTeed Corporation B
20 Moores Road EVIEWED FOR f
Malvern,PA 19355 CODE COMPLIANCE
SCOPE: ST. L_UCIE COUNTY
This NOA is being issued under the applicable rules and regulations governing the us oQaction materials.The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below.The Miami-Dade County Product Control Section
(In Miami Dade County)and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this
product or material tested for quality assurance purposes.If this product or material fails to perform in the accepted
manner,the manufacturer will incur the expense of such testing and the AHJ may immediately revoke,modify,or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein,and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: CertainTeed Modified Bitumen Roofing Systems over Wood-Decks.
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use,and/or manufacture of the product or process.Misuse of this NOA as an endorsement of any product,
for sales,advertising or any other purposes shall automatically terminate this NOA.Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed,then it shall be done
in its entirety.
INSPECTION: A copy of4his entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA No.. 17-1003.04 and consists of pages 1 through 49.
The submitted documentation was reviewed by Alex Tigera.
File Copy
NOA No.: 18-1127.18;
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
i
Page 1 of 49
i
ROOFING SYSTEM APPROVAL
Category Roofing
Sub-Category: Modified Bitumen
Material: APP/SBS
Deck Type• Wood
Maximum Design Pressure: -127.5 psE
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions Specification Description
All Weather/Empire Base 39 3/s"x 65'10"; ASTM D 4601,Type Asphalt coated,fiberglass reinforced
Sheet Roll weight: 701bs. II base sheet.
(2 squares)
Flexiglas Base Sheet 39 3/8"x 98'9"; Roll ASTM D 4601,Type Modified Bitumen coated fiberglass
weight: 90 lbs. II base sheet.
(3 squares)
Flintlastic Base 20 39 3/8"x 49'6";Roll ASTM D 6163, Modified Bitumen coated fiberglass
weight: 90 lbs. Grade S,Type I base sheet.
(1.5 squares)
Flintglas Ply 4 39 3/3"x 1647';Roll ASTM D 2178,Type Fiberglass,asphalt impregnated ply sheet.
weight: 38 lbs. IV
(5 squares) UL Type G1
Flintglas Premium Ply 6 39 3/s"x 1647';Roll ASTM D 2178,Type Fiberglass,asphalt impregnated ply
weight: 40 lbs. VI sheet.
(5 squares) UL Type GI
Flintlastic STA 39 3/8"x 32' 10";Roll ASTM D 6222, Smooth surfaced APP Modified
weight: 87 lbs. Grade S,Type I Bitumen membrane with non-woven
(1 square) polyester mat reinforcement for torch
application.
Flintlastic GTA 39 3/8" x 32' 10";Roll ASTM D 6222, Granule surfaced APP Modified
weight: 105 lbs. Grade G, Type I Bitumen membrane with non-woven
(1 square) polyester mat reinforcement for torch
application.
Flintlastic GTA-FR 39 3/s"x 32' 10";Roll ASTM D 6222, Granule surfaced APP Modified
weight: 1051bs. Grade G,Type I Bitumen membrane with non-woven
(1 square) polyester mat reinforcement for torch
application.
Flintlastic GMS 39 3/8"x 32' 10";Roll ASTM D 6164, Granule surfaced SBS Modified
weight: 941bs. Grade G,Type I Bitumen membrane with non-woven
(1 square) polyester mat reinforcement for mop
application.
NOA No.: 18-1127.18
CMLAAMMI-DAMECOUMNTY Expiration Date: 06/19/23
® Approval Date: 01/17/19
Page 2 of 49
"r
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions Specification Description
Flintlastic FR-P 39 3/8"x 32' 10";Roll ASTM D 6164, Fire resistant, granule surfaced SBS
weight: 101 lbs. Grade G,Type I Modified Bitumen Membrane with
(1 square) non-woven polyester mat
reinforcement for mop application.
Flintlastic Premium FR-P 39 3/8" x 32' 10";Roll ASTM D 6164, Fire resistant,granule surfaced SBS
weight: 101 lbs. Grade G,Type II Modified Bitumen Membrane with
(1 square) non-woven polyester mat
reinforcement for mop application.
Flintlastic FR Dual Cap 39 3/8"x 32' 10";Roll ASTM D 6162, Granule surfaced SBS modified
weight: 103 lbs. Grade G,Type II bitumen membrane with a nonwoven
(1 square) polyester/fiberglass composite mat
reinforcement for use in cold or mop
applications.
Flintlastic Cap 30 39 3/8"x 32':10";Roll ASTM D 6163, Granule surfaced SBS Modified
weight: 86 lbs. Grade G,Type I Bitumen membrane with fiberglass mat
(1 square) reinforcement for mop applications.
Flintlastic FR Cap 30 39 3/8"x 32' 10";Roll ASTM D 6163, Fire resistant,granule surfaced SBS
weight: 86 lbs. Grade G,Type I Modified Bitumen membrane with
(1 square) fiberglass mat reinforcement for mop
applications.
Flintlastic FR Cap 30 T 39-3/8"x 32' 10";Roll ASTM D 6163, Granule surfaced SBS Modified
weight: 1001bs. Grade G,Type I Bitumen membrane with fiberglass
(1 square) mat reinforcement for torch
application.
Flintlastic Base 20 T 39-3/8"x 33';Roll ASTM D 6163, Modified Bitumen, coated fiberglass
Weight: 81 lbs. Grade S,Type I base sheet for torch application.
(1 square)
Flintlastic Ultra Poly SMS 39 3/8"x 32' 10';Roll ASTM D 6164, Smooth surfaced SBS Modified
Base Sheet weight: 90 lbs. (1 Grade S,Type I Bitumen Membrane with non-woven
squares) polyester mat reinforcement for mop or
torched applications.
Glasbase Base Sheet. 36" x 98' 9"; Roll ASTM D 4601,Type Asphalt coated,fiberglass base sheet.
weight: 75 lbs. II
(3 squares)
Flintlastic Poly SMS Base 39 3/8"x 64'3";Roll ASTM D 4601, Modified Bitumen coated polyester
Sheet weight: 90 lbs. Grade S,Type II base sheet.
(2 squares)
NOA No.: 18-1127.18
MIAMI-Dane CouNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 3 of 49
d
i
i
Membrane Type: APP Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32"or greater plywood or wood plank attached with 8d_ring shank nails spaced 4"o.c._at
wood.joists spaced maximum 24"o.c.
System Type E(7): Base sheet mechanically fastened.
All General and System Limitations apply.
Base.Sheet: One ply of All Weather/Empire Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet;Glasbase Base
Sheet or Flintglas Premium Ply 6 mechanically attached as detailed below.
Fastening#1: Base sheet shall be lapped 4" and fastened with 11 ga. annular ring shank nails and approved_ tin
caps 8"o.c. in the lap and three rows staggered in the center of the-sheet 8"o.c.
Ply Sheet: One ply of All Weather/Empire Base Sheet,Flintlastic Ultra Poly SMS Base Sheet,Glasbase
(Optional) Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or one
or more Fhntglas Ply 4 or Flintggas Premium Ply 6 adhered to the base sheet in a full mopping
of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq.or one ply of
Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered or Flintlastic STA or
Flintlastic APP Base T torch adhered.
Membrane: Flintlastic GTA or Flintlastic GTA-FR torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -60 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 31 of 49
r
I
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions Specification Description
Yosemite Venting Base Sheet 39 3/s"x 32'10";Roll ASTM D 3909 Mineral Surfaced fiberglass reinforced
weight: 85 lbs. ASTM D 4897,Type buffer sheet.
(1 square) H
UL Type G3
Flintlastic APP Base T 39 3/8"x 65' 4";Roll ASTM D 6509 Modified Bitumen coated fiberglass
weight: 1001bs. base sheet.
(2 squares)
Flintlastic Ultra Glass SA 39 3/8"x 33'11";Roll ASTM D 1970 Self-adhering,fiberglass reinforced,
weight: 731bs. SBS modified bitumen base/ply sheet.
(1 square)
Black DiamondTM Base Sheet 36"x 687';Roll ASTM D 1970 Self-adhering fiberglass reinforced
weight: 78 lbs. ASTM D4601 Type I modified bitumen base sheet
(2 squares)
Flintlastic SA PlyBase 39 3/8"x 66'6";Roll ASTM D 4601, Self-adhering,fiberglass reinforced,
weight: 861bs. Grade S,Type H SBS modified bitumen base/ply sheet.
(2 squares) ASTM D 1970
Flintlastic SA Mid Ply 39 3/8"x 32'1"; ASTM D 6163, Self-adhering,polyester reinforced,
Roll weight: 62 lbs. Grade S,Type I SBS modified bitumen ply sheet.
(1 square)
F1intBond Brush 5 gallon pails ASTM D 3019 Cold applied, SBS polymer modified
asphalt adhesive.
NOA No.: 18-1127.18
MIAMbUAUE COUNTY= Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 4 of 49
I
I
I
i
i
i
APPROVED INSULATIONS:
TABLE 2
Product Name ' Product Description Manufacturer
(With Current NOA)
F1intBoard ISO Polyisocyanurate foam insulation CertainTeed Corp.
FlintBoardH ISO Polyisocyanurate foam insulation CertainTeed Corp.
FlintBoard ISO Cold Polyisocyanurate foam insulation CertainTeed Corp.
ACFoam-II Polyisocyanurate foam insulation Atlas Roofing Corp.
ACFoam-III Polyisocyanurate foam insulation Atlas Roofing Corp.
DensDeck Water resistant gypsum board Georgia Pacific Gypsum LLC
DensDeck Prime Water resistant gypsum board Georgia Pacific Gypsum LLC
H-Shield Polyisocyanurate foam insulation Hunter Panels LLC
ENRGY 3 Polyisocyanurate foam insulation Johns Manville Corp.
ENRGY 3 25 PSI Polyisocyanurate foam insulation Johns Manville Corp.
Multi-Max FA-3 Polyisocyanurate foam insulation RMax Operating,LLC
SECUROCK Gypsum-Fiber Roof Board homogenous fiber reinforced USG Corp.
Structodek High Density Fiberboard High Density Wood Fiber Insulation Blue Ridge Fiberboard,Inc.
Roof Insulation board
FescoBoard Expanded perlite and fiber insulation Johns Manville Corp.
NOA No.: 18-1127.18
MII•DADe COUNTY j Expiration Date: 06/19/23
Approval Date:01/17/19
Page 5 of 49
APPROVED FASTENERWADHESIVES:
TABLE 3
Fastener Product Product Manufacturer
Number Name Description Dimensions (With Current NOA)
1. Trufast#12 DP Fastener Insulation fastener for wood various Altenloh,Brinch&Co.U.S.,
and steel decks Inc.
2. Trufast 3"Metal Galvalume steel plate 3"round Altenloh,Brinch&Co.U.S.,
Insulation Plate Inc.
3. FlintFast#12 Coated,carbon steel screw various CertainTeed Corp.
4. FlintFast 3"Insulation Galvalume AZ50 steel plate 3"round CertainTeed Corp.
Plate
5. FlintFast#14 Insulation fastener for wood various CertainTeed Corp.
and steel decks
6. Simplex MAXX Cap Polymer fastner 1"long Simplex Nails,Inc.
7. #12 Standard Roofgrip Insulation fastener for wood various OMG,Inc.
and steel.
8. OMG 3"Galvalume Steel Galvalume stress plate 3 round OMG,Inc.
Plate
9. Trufast#14 HD Fastener Insulation fastener for wood various Altenloh,Brinch&Co.U.S.,
and steel decks Inc.
10. OMG Heavy Duty Insulation and membrane Various OMG,Inc.
fastener
11. 3 in. Round Metal Plate Galvalume AZ50 steel plate 3"round OMG,Inc.
12. AccuTrac Hextra Carbon steel fastener Various OMG,Inc.
13. AccuTrac Plate Galvalume stress plate. 3"square OMG,Inc.
14. AccuTrac Flat Bottom A2-SS aluminized steel plate 3"square OMG,Inc.
Plate
15. Millennium One Step Polyurethane two component 1.5 liters H.B.Fuller Company
Foamable Adhesive high rise insulation adhesive
16. Millennium One Step Polyurethane two component 1.5 liters H.B.Fuller Company
Green Foamable Adhesive high rise insulation adhesive
17. Millennium PG-1 Low Polyurethane two component 1.5 liters H.B. Fuller Company
Viscosity Insulation low rise insulation adhesive
Adhesive
18. Insta Stik Quik Set Polyurethane one component It is supplied The Dow Chemical Company
Insulation moisture curing adhesive in pressurized
cylinders with
a net weight
of 231bs.,
with a total
unit weight of
30 lbs.
NOA No.: 18-1127.18
MIAMI-DADE COUNTY
� � Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 6 of 49
i;
APPROVED FASTENERS/ADHESIVES:
TABLE 3
Fastener Product Product Manufacturer
Number Name Description Dimensions (With Current NOA)
19. OMG OlyBond 500 Spray polyurethane foam 10 gal.bag-in- OMG,Inc.
Adhesive insulation adhesive box set and
1.5 liters
SpotShot
cartridge
20. OMG OlyBond 500 Green Spray polyurethane foam 10 gal.bag-in- OMG,Inc.
Adhesive insulation adhesive box set and
1.5 liters
SpotShot
cartridge
APPROVED SURFACING/COATING OPTIONS:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions.Any coating,listed
below,used as a surfacing,must be listed within a current NOA.
System Number Manufacturer Application
1. Generic' Gravel applied at 400 lbs/sq.,adhered with flood coat of asphalt at
60 lbs/sq.
2. Generic Slag applied at 3001bs/sq.,adhered with flood coat of asphalt at 60
lbs/sq.
3. Karnak Corp. Karnak(#97 AF)Fibrated Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
4. CertainTeed Corp. F1intCoat A-150 applied at an application rate of 1.5 gal/sq.
5. Gardner Asphalt Corp. APOC#212 Fibered Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
6. Gardner Asphalt Corp. APOC#400 Sunbrite applied at an application rate of 3 gal./sq.
i
NOA No.: 18-
MAMI-DADE coUNTY 1127.18
Expiration Date: 112718
Approval Date:01/17/19
Page 7 of 49
EVIDENCE SUBMITTED:
Test Agency/Identifier Name Report Date
Factory Mutual Research Corp. FM 4470 3Y8A1.AM 03/23/96
FM 4470 OD3A3.AM 04/04/97
FM 4470 1D7A4.AM 11/09/98
FM 4470 2DOAO.AM 12/23/98
FM 4470 3024311 11/01/06
FM 4470 3031350 09/27/07
FM 4470 3036182 07/31/09
FM 4470 3039046 06/15/10
FM 4470 3048520 09/19/13
Underwriters Laboratories,Inc. UL 790 R11656 01/11/13
United States Testing Company ASTM D 5147 97-457-2R 12/02/87
ASTM D 5147 97-457-4 06/03/88
Momentum Technologies,Inc. ASTM D 6164 AX31G8F 06/05/09
TrinitylERD TAS 114(J) 3507.08.99-1 04/18/01
TAS 114(J) 3504.06.01-1 06/05/01
TAS 114 3521.07.04 07/29/04
TAS 114 3533.01.06 01/06/06
TAS 114(H) Letter 04/05/06
TAS 117(B) 3503.10.06 10/10/06
TAS 117 (B) 06490.04.07-R1 06/27/07
TAS 117 (B)/ASTM D 6862 C8500SC.11.07 11/30/07
FM 4470,TAS 114,FM 4470, C8370.08.08-R1 10/05/09
TAS 114(J)
TAS 114(H),TAS 117(B),TAS C30560.06.10 06/10/10
114(J)
FM 4470,TAS 114 C32830.07.10 07/20/10
ASTM D 6164/D 4798 C31410.01.11-2 01/10/11
TAS 117 B C35500.02.11 02/09/11
FM 4470(K)/TAS 114(J) 03515.07.03-1-R1 06/27/12
ASTM D 1876,TAS 114(11), C42110.08.12 08/13/12
TAS 117(B)
FM 4474/TAS 114 C39670.08.12 08/20/12
ASTM D_4601 C40050.09.12-1 09/28/12
ASTM D 1970 C40050.09.12-2 09/28/12
ASTM D 5147/D 4798 C31410.10.10-R1 11/01/12
ASTM D 5147/D 4798 C31410.01.11-1-R1 11/01/12
ASTM D 4798 C31410.01.11-2A-Rl 02/21/13
ASTM D 4798 C31410.12.13 12/05/13
ASTM D 6222 C40050.12.13-R1 12/31/13
TAS 117,TAS 114 C30310.12.09-R1 03/07/14
ASTM D 2178 C47250.03.14 03/26/14
ASTM D 1876,TAS 114(H), C45620.03.14 03/27/14
FM 4474
NOA No.:18-1127.18
MIAM4DADE COUNTY
i Expiration Date: 06/19/23
Approval Date:O1/17/19
Page 8 of 49
EVIDENCE SUBMITTED:
Test.Agency/Identifier Name Report Date
ASTM D4601 CTR-SC8740.04.15-R2 04/21/15
ASTM D 1876,TAS 114(H), C47320.03.14-R1 04/01/15
FM 4474
ASTM D 1876 C35460.05.11-R1 05/20/15
FM 4474(D)/UL 1897/TAS CTR-SC10420.01.16 01/25/16
114(J)
FM 4474/TAS 114(J) CTR-SC9175.09.16-2 09/06/16
FM 4470 (K)/UL 1897/TAS CTR-SC11590.08.16- 09/06/16
114(J) Rl
ASTM D 4601-04(2012),Type II CTR-SC11145.09.16- 09/19/16
3C
ASTM D 4601-04(2012),Type II CTR-SC11145.09.16- 09/19/16
3A
ASTM D 6163 CTR-SC11145.09.16- 09/19/16
5A
ASTM D 6222 CTR-SC11145.09.16- 09/19/16
7A
PRI Construction Materials ASTM D 6163 CTC-056-02-01 08/25/10
Technologies LLC ASTM D 6163 CTC-066-02-01 08/09/11
ASTM D 6222 CTC-071-02-01 08/08/11
ASTM D 6164/D 4798 CTC-093-02-01 08/09/11
ASTM D 4601 CTC-126-02-01 03/12/12
ASTM D 2178 CTC-123-02-01 03/13/12
ASTM D 4601 CTC-127-02-01 03/13/12
ASTM D 6163 CTC-128-02-01 06/11/12
ASTM D 6163 CTC-129-02-01 06/11/12
ASTM D 6164 CTC-132-02-01 06/11/12
ASTM D 6164 CTC-161-02-01 05/09/13
ASTM D 6162 CTC-183-02-01 10/02/13
ASTM D 6164 CTC-190-02-01 12/02/13
ASTM D 1970 CTC-199-02-01 01/22/14
ASTM D 6163 CTC 319-02-01 08/22/17
NOA No.: 18-1127.18
M AMIOADe COutvnr Expiration Date: 06/19/23
Approval Date:O1/17/19
Page 9 of 49
APPROVED ASSEMBLIES:
Membrane Type: APP Modified
Deck Type 1I: Wood,Insulated
Deck Description: "/32" or greater plywood or wood plank attached with 8d ring shank nails spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type A(1): Anchor sheet mechanically fastened; all layers of insulation adhered with approved asphalt.
All General and System Limitations apply.
Anchor Sheet: One ply of All Weather/Empire Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet, Glasbase Base
Sheet or Flintglas Premium Ply 6 mechanically attached as detailed below.
Fastening: Anchor sheet shall be lapped 4" and fastened with 11 ga.annular ring shank nails and approved
tin caps 8"o.c.in the lap and three rows staggered in the center of the sheet 8"o.c.
One or more layers of any of the following insulations.
Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft'
ACFoam-H,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold;Multi-Max FA-3,ENRGY 3,H-Shield,
F1intBoarda ISO
Minimum 1.51'thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20401bs./100 ft . Please refer to Roofmg Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered to the
insulated substrate.
Ply Sheet: One ply of All Weather/Empire Base Sheet,Flintlastic Ultra Poly SMS,Glasbase Base Sheet,
(Optional) Flexiglas Base Sheet,Flintlastic Base 20 or Flintlastic Poly SMS Base or one or more plies of
Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to the base sheet in a full mopping of
approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. or one ply of
Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered or Flintlastic STA or
Flintlastic APP Base T torch adhered.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR
Cap 30 T torch adhered.
Or
One ply of Flintlastic GTA or Flintlastic GTA-FR torch adhered to base or ply sheet.
NOA No.: 18-1127.18
M AM4DADE COUNTY Expiration Date: 06/19/23
AD
j Approval Date: 01/17/19
Page 10 of 49
i
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf(See General Limitation#7)
Pressure:
i
I
i
i
i
NOA No.: 18-1127.18
MIAMI-DAD,COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 11 of 49
I�
Membrane Type: SBS Modified
Deck Type 1I: Wood,Insulated
Deck Description: 19/32" or greater plywood or wood plank attached with 8d ring shank nails spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type A(2): Anchor sheet mechanically fastened; all layers of insulation adhered with approved asphalt.
All General and System Limitations apply.
Anchor Sheet: One ply of All Weather/Empire Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet,Glasbase
Base Sheet or Flintglas Premium Ply 6 mechanically attached as detailed below.
Fastening: Anchor sheet shall be lapped 4" and fastened with 11 ga. annular ring shank nails and
approved tin caps 8"o.c.in the lap and three rows staggered in the center of the sheet 8"o.c.
One or more layers_of any of the following insulations.
Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft2
ACFoam-II,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold,ENRGY 3,ENRGY 3 25 PSI,H-Shield,
FlintBoardx ISO
Minimum 1.5"thick N/A N/A
FescoBoard
Minimum%"thick N/A N/A
Structodek High Density Fiberboard Roof Insulation
Minimum%11 thick N/A N/A
DensDeck,DensDeck Prime
Minimum%11 thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 2040 lbs./100 ft . Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One ply of All Weather/Empire Base Sheet,Flintlastic Ultra Poly SMS Base Sheet,Glasbase
Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet
adhered to the insulated substrate in a full mopping of approved asphalt applied within the
EVT range and at a rate of 2040 lbs./sq
NOA No.: 18-1127.18
MIAMI DADS CO Expiration Date: 06/19/23
Approval Bate: 01/17/19
Page 12 of 49
Ply Sheet: One ply of All Weather/Empire Base Sheet,Glasbase Base Sheet,Flexiglas Base Sheet,
(Optional) Flintlastic Base 20,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet
or one or more plies of Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to base sheet in a
full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq.
or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered or
Flintlastic Ultra Poly SMS Base Sheet torch applied.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium
FR-P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base/ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 401bs./sq. or Flintlastic
FR Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf(See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAM4DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 13 of 49
I
Membrane Type: APP Modified
Deck Type 1I: Wood;Insulated
Deck Description: 19/3239 or greater plywood or wood plank attached with 8d ring shank nails spaced 6"o.c. at
wood joists spaced maximum 24"o. c.
System Type A(3): Anchor sheet mechanically fastened; all layers of insulation adhered with approved asphalt.
All General and System Limitations apply.
Anchor Sheet: One ply of All Weather/Empire Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet, Glasbase Base
Sheet,Flintglas Premium Ply 6 mechanically attached as detailed below.
Fastening: Anchor sheet shall be lapped 4" and fastened with 11 ga. annular ring shank nails and approved
tin caps 8"o.c. in the lap and three rows staggered in the center of the sheet 8"o.c.
One or more layers of any of the following insulations.
Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
ACFoam-II,ACFoam-III,F1intBoard ISO,FlintBoard ISO Cold,Multi-Max FA-3,ENRGY 3,H-Shield,
FlintBoardR ISO
Minimum 1.5"thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the.
EVT range and at a rate of 2040 lbs./100 ftz. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered to the
insulated substrate.
Ply Sheet: One ply of All Weather/Empire Base Sheet,Flintlastic Ultra Poly SMS Base Sheet,Glasbase
(Optional) Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20 or Flintlastic Poly SMS Base Sheet or one
or more plies of Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to the base sheet in a full
mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. or one
ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered or Flintlastic STA
or Flintlastic APP Base T torch adhered.
Membrane: Flintlastic GTA or Flintlastic GTA-FR torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -60 psf. (See General Limitation#7)
Pressure:
NOA No.:18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
e Approval Date:01/17/19
Page 14 of 49
I
Membrane Type: SBS Modified
Deck Type 1I: Wood,Insulated
Deck Description: 19/32"or greater plywood or wood plank attached with 8d ring shank nails spaced 6"o.c. at
wood joists spaced maximum 24"o. c.
System Type A(4): Anchor sheet mechanically fastened; all layer of insulation adhered with approved asphalt.
All General and System Limitations apply.
Anchor Sheet: One ply of All Weather/Empire Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet, Glasbase Base
Sheet or Flintglas Premium Ply 6 mechanically attached as detailed below.
Fastening: Anchor sheet shall be lapped 4" and fastened with 11 ga. annular ring shank nails and approved
tin caps 8"o.c. in the lap and three rows staggered in the center of the sheet 8"o.c.
One or more layers of any of the following insulations.
Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ftz
ACFoam-II,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold,ENRGY 3,ENRGY 3 25 PSI,H-Shield,
FlintBoarda ISO
Minimum 1.5"thick N/A N/A
FescoBoard
Minimum 3/4"thick N/A N/A
Structodek High Density Fiberboard Roof Insulation
Minimum%"thick N/A N/A
DensDeck,DensDeck Prime
Minimum I/4"thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 2040 lbs./100 fe. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One ply of All Weather/Empire Base Sheet,Flintlastic Ultra Poly SMS Base Sheet,Glasbase
Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet adhered
to the insulated substrate in a full mopping of approved asphalt applied within the EVT range
and at a rate of 20-401bs./sq.
NOA No.: 18-1127.18
MIAMI DADE COUNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 15 of 49
I
t
las ase Base Sheet Flexi las Base Sheet
Sheet: One 1 of All Weather/Empire ire Base Sheet, G b
Pl Sheg ,
Y PY P
(Optional) Flintlastic Base 20,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet or
one or more plies of Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to the base sheet in a
full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. or
one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered or Flintlastic
Ultra Poly SMS Base Sheet torch applied.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR
Cap 30 T torch adhered to base/ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -60 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 16 of 49
I
I
Membrane Type: APP Modified
Deck Type 1I: Wood,Insulated
Deck Description: 15/32" or greater CDX plywood or wood plan attached with#8 screws spaced 6"o.c. at wood
joists spaced maximum 24"o.c.
System Type B(1): Base layer of insulation mechanically fastened,top layer adhered with approved adhesive.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft'
ACFoam-II,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold,H-Shield,FlintBoardH ISO
Minimum 1.5"thick 1,3 1:1.33 W
Note: Base layer shall be mechanically attached with fasteners and density described above. Insulation panels
listed are minimum sizes and dimensions;if larger panels are used the number of fasteners per board shall be
increased maintaining the same fastener density(See Roofing Application Standard RAS 117 for fastening
details).
Top Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft2
ACFoam-II,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold,H-Shield,FlintBoardH ISO
Minimum 1.5"thick N/A N/A
Note: Top layer of insulation shall be adhered with Millennium One Step Foamable Adhesive,Millennium One
Step Green Foamable Adhesive, Millennium PG-1 Low Viscosity Insulation Adhesive in 3/4" — 1" wide beads
spaced 12 inch o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Base Sheet: One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA,self-adhered to the
insulated substrate.
PlySheet: One or more lies of Flintlastic APP Base T or Flintlastic STA,torch adhered to the base sheet.
P
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FF,torch adhered to the ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -67.5 psf(See General Limitation#7)
Pressure:
i
NOA No.: 18-1127.18
M AMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 17 of 49
i
Membrane Type: APP Modified
i
Deck Type 1I: Wood,Insulated
Deck Description: 115/32" or greater CDX plywood or wood plank attached with#8 screws spaced 6"o.c. at
'wood joists spaced maximum 24"o.c.
System Type B(2): Base layer of insulation mechanically fastened,top layer adhered with approved
adhesive.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft2
ACFoam-II,ACFoam-III,F1intBoard ISO,FlintBoard ISO Cold,H-Shield,FUntBoardg ISO
Minimum 1.5"thick 1,3 1:1.33 ft2
Note: Base layer shall be mechanically attached with fasteners and density described above. Insulation panels
listed are minimum sizes and dimensions;if larger panels are used the number of fasteners per board shall be
increased maintaining the same fastener density(See Roofing Application Standard RAS 117 for fastening
details).
Top Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft2
SECUROCK Gypsum-Fiber Roof Board
Minimum 1/4"thick N/A N/A
Note: Top layer of insulation shall be adhered with Millennium One Step Foamable Adhesive,Millennium One
Step Green Foamable Adhesive, Millennium PG-1 Low Viscosity Insulation Adhesive, Insta-Stik Quik Set
Insulation Adhesive, OMG OlyBond 500 Adhesive or OMG OlyBond 500 Green Adhesive in 3/4" — 1" wide
beads spaced 12 inch o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Base Sheet: One ply of Flintlastic STA or Flintlastic APP Base T,torch adhered to the insulated substrate.
Ply Sheet: One ply of Flintlastic STA or Flintlastic APP Base T,torch adhered to the base sheet.
(Optional)
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FR,torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -90 psf(See General Limitation#7)
Pressure:
I ,
MIAMI•DADE COUNTY NOA No.: 18-1127.18
Expiration Date: 06/19/23
Approval Date:01/17/19
Page 18 of 49
Membrane Type: SBS/APP Modified
Deck Type 1I: Wood,Insulated
Deck Description: 115/32" or greater APA rated CDX plywood or wood plank attached with 8d ring shank
nails spaced 6"o.c.at wood joists spaced maximum 24"o.c.
System Type C(1): All layers of insulation simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver(Optional) Insulation Fasteners Fastener
able 3 Density/fe
ACFoam-II,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold
Minimum 1.5"thick N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density.
Top Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
ACFoam-II,ACFoam-III,FlintBoard ISO,F1intBoard ISO Cold
Minimum 1.5"thick 2 with 9 or 4 with 5 1:1.6 fe
Note: Top insulation layer shall be mechanically attached using the fastener density listed above.The insulation
panels listed are minimum sizes and dimensions; if larger panels are used,the number of fasteners shall be
increased maintaining the same fastener density.Insulation fasteners shall be tested for withdrawal resistance
in compliance with Testing Application Standard TAS 105 to confirm compliance with the wind load
requirements.Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Primer: FlintPrime primer applied at a rate of 0.5 gal/sq and allowed to dry prior to application of base
sheet.
*Required only for Flindastic SA PlyBase or Flintlastic SA Mid Ply.
Base Sheet: One ply of Flintlastic SA PlyBase or Flintlastic SA Mid Ply, self-adhered to the insulated
substrate.
*Requires use of self-adhering sheet overtop.
Or
One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA,torch applied to the
insulated substrate.
*Requires use of torch-applied sheet overtop.
Ply Sheet: One ply of Flintlastic SA PlyBase or Flintlastic SA Mid Ply, self-adhered to the base sheet.
(Optional) *Requires use of self-adhering sheet overtop.
Or
One ply of Flintlastic Ultra Poly SMS Base Sheet,Flintlastic Base 20 T,Flintlastic APP Base T
or Flintlastic STA torch adhered to the base sheet.
*Requires use of torch-applied sheet overtop.
NOA No.: 18-1127.18
MIAM4DAD;COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 19 of 49
i
Membrane: Flintlastic FR Cap 30 T,Flintlastic GTA or Flintlastic GTA-FR torch adhered to base or ply
sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf(See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 20 of 49
i
i
Membrane Type: APP Modified
Deck Type 1I: Wood,Insulated
Deck Description: 15/32" or greater CDX plywood or wood plank attached with#8 screws spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type C(2): All layers of insulation simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft'
ACFoam-II,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold,A-Shield,F1intBoardn ISO
Minimum 1.5"thick N/A N/A
Note: All layers shall be simultaneous) fastened; see to layer below for fasteners and density.
Y Y � P Y tY
Top Insulation Laver Insulation Fasteners Fastener
able 3 Density/ft2
SECUROCK Gypsum-Fiber Roof Board
Minimum 1/4"thick 1,3 1:1.33 ftz
Note: All layers of insulation shall be mechanically attached using the fastener density listed above.The
insulation panels listed are minimum sizes and dimensions; if larger panels are used,the number of fasteners
shall be increased maintaining the same fastener density.Insulation fasteners shall be tested for withdrawal
resistance in compliance with Testing Application Standard TAS 105 to confirm compliance with the wind load
requirements.Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Base Sheet: One ply of Flintlastic STA or Flintlastic APP Base T,torch adhered to the insulated substrate.
Ply Sheet: One ply of Flintlastic STA or Flintlastic APP Base T,torch adhered to the base sheet.
(Optional)
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FR,torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -67.5 psf(See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
M�nM1•DADecou Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 21 of 49
i
i
Membrane Type: APP Modified
Deck Type 1I: Wood,Insulated
I
Deck Description: 15/32' or greater CDX plywood or wood plank attached with#8 screws spaced 6" o.c. at wood
joists spaced maximum 24"o.c.
System Type C(3): All layers of insulation simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Base Insulation Laver Insulation Fasteners Fastener
able 3 Density/W
ACFoam-H,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold,H-Shield,F1intBoardH ISO
Minimum 1.5"thick N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density.
Top Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
ACFoam-H,ACFoam-III,FlintBoard ISO,FlintBoard ISO Cold,H-Shield,FlintBoardn ISO
Minimum 1.5"thick 1,3 1:1.33 fe
Note: All layers of insulation shall be mechanically attached using the fastener density listed above.The
insulation panels listed are minimum sizes and dimensions; if larger panels are used,the number of fasteners
shall be increased maintaining the same fastener density.Insulation fasteners shall be tested for withdrawal
resistance in compliance with Testing Application Standard TAS 105 to confirm compliance with the wind load
requirements.Please refer to Roofing Application Standard RAS 117 for insulation attachment.
Base Sheet: One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA,self-adhered to the
insulated substrate.
Ply Sheet: One or more plies of Flintlastic APP Base T or Flintlastic STA,torch adhered to the base sheet.
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FR,torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -75.0 psf(See General Limitation#7)
Pressure:
M aHI•naoe NOA No.: 18-1127.18
couw7Y
• •� Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 22 of 49
Membrane Type: SBS Modified
Deck Type 1I: Wood,Insulated
Deck Description: 1 62' or greater APA rated CDX plywood or wood plank attached with 8d ring shank nails
spaced 6"o.c. at wood joists spaced maximum 24"o.c.
System Type D(1): All layers of insulation and base sheet simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Insulation Laver Insulation Fasteners Fastener
able 3 Density/fe
Any Approved Polyisocyanurate Listed in Table 2
Minimum 1.5"thick N/A N/A
Note: Insulation layer shall have preliminary attachment,prior to the installation of the base sheet, at an
application rate of two fasteners per board for insulation boards having no dimension greater than 4 ft.,and
four fasteners for any insulation board having no dimension greater than 8 ft.All layers of insulation and base
sheet shall be simultaneously fastened. See base sheet below for'fasteners and density.
Base Sheet: One ply of Glasbase Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20,Yosemite
Venting Base Sheet,Flintlastic Poly SMS Base Sheet and Flintlastic Ultra Poly SMS Base
Sheet,mechanically attached as described below.
Fastening#1: Trufast#12 DP Fasteners or Trufast#14 HD Fasteners with Trufast 3"Metal Insulation
Plates,FlintFast#12 fasteners or FlintFast#14 fasteners with FlintFast 3"Insulation Plates
spaced 8"o.c.at the 4"wide laps and 8"o.c. in three,equally spaced staggered center rows.
Ply Sheet: One ply of Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly
(Optional) SMS Base Sheet applied in FlintBond Brush at a rate of 1.0— 1.5 gal/sq to the base sheet.
Membrane: One ply of Flintlastic Cap 30,Flintlastic FR Cap 30,Flintlastic FR Dual Cap,Flintlastic FR-
P,Flintlastic Premium FR-P or Flintlastic GMS applied in FlintBond Brush at a rate of 1.0—
1.5 gal/sq to base or ply sheet.
Surfpcing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf(See General Limitation#7)
Pressure:
i
NOA No.: 18-1127.18
M AMI•DADE CouNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 23 of 49
11
Membrane Type: SBS Modified
Deck Type 1I: Wood,Insulated
Deck Description: 15/32" or greater APA rated plywood or wood plank attached with#10 wood screws spaced 6"
o.c. at wood joists spaced maximum 24"o.c.
System Type D(2): All layers of insulation and base sheet simultaneously attached.
All General and System Limitations apply.
One or more layers of any of the following insulations.
Insulation Laver Insulation Fasteners Fastener
able 3 Density/fe
Any Approved Polyisocyanurate Listed in Table 2
Minimum 1.5"thick N/A N/A
Note: Insulation layer shall have preliminary attachment,prior to the installation of the base sheet, at an
application rate of two fasteners per board for insulation boards having no dimension greater than 4 ft.,and
four fasteners for any insulation board having no dimension greater than 8 ft.All layers of insulation and base
sheet shall be simultaneously fastened. See base sheet below for fasteners and density.
Base Sheet: One ply of Glasbase Base Sheet,Yosemite Venting Base Sheet,All Weather/Empire Base
Sheet,Flexiglas Base Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic
Ultra Poly SMS Base Sheet,mechanically attached as described below.
Fastening#1: Fastened with Trufast#14 HD Fasteners with Trufast 3"Metal Insulation Plates or FlintFast
#14 Fasteners with FlintFast 3"Insulation Plates spaced 8"o.c.at the 4"wide laps and 8"o.c.
in three, equally spaced staggered center rows.
Ply Sheet One ply of Glasbase Base Sheet,All Weather/Empire Base Sheet, Flexiglas Base Sheet,
(Optional): Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet
adhered to base sheet in a full mopping of approved asphalt applied within the EVT range and
at a rate of 20-40 lbs./sq. or one ply of Glasbase Base Sheet,All Weather/Empire Base Sheet,
Flexiglas Base Sheet,Flintlastic Base 20,Flintlastic Base 20 T or Flintlastic Ultra Poly SMS
Base torch applied to base sheet or one ply of Black Diamond Base Sheet or Flintlastic Ultra
Glass SA self-adhered to the base sheet.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 401bs./sq.or one ply of
Flintlastic FR Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -97.5 psf. (See General Limitation#7)
Pressure:
i
NOA No.:18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
j Page 24 of 49
i
i
I '
Membrane Type: SBS Modified
Deck Type 1: Wood,Non-insulated
Deck Description: 15/32' or greater CDX plywood or wood plank attached with 8d ring shank nails spaced 6"o.c at
wood joists spaced maximum 24"o.c.
System Type E(1): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base Sheet,All
Weather/Empire Base Sheet,Flintlastic Base 20 or Flintlastic Poly SMS Base Sheet
mechanically attached as detailed below.
Fastening#1: Fastened with Simplex MAXX Cap fasteners spaced 9"o.c. in the 2"side lap and 12"o.c, in
two evenly divided, staggered rows in the center of the sheet.
Membrane: One ply of Flintlastic Cap 30,Flintlastic FR Cap 30,Flintlastic FR Dual Cap,Flintlastic FR-P,
Flintlastic Premium FR-P or Flintlastic GMS adhered to the base sheet with approved mopping
asphalt applied within the EVT range and at a rate of 20-40 lbs/sq. or one ply of Flintlastic FR
Cap 30 T,torch-applied to base sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf(See General Limitation#9)
Pressure:
NOA No.: 18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 25 of 49
Membrane Type: APP Modified
Deck Type 1: Wood,Non-insulated
Deck Description: 15/32 or greater COX plywood or wood plank attached with 8d ring shank nails spaced 6"o.c.
at wood joists spaced maximum 24"o.c.
System Type E(2): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Flintlastic APP Base T mechanically attached as detailed below.
Fastening#1: Fastened with Simplex MAXX Cap fasteners spaced 9"o.c.in the 2"side lap and 12"o.c. in
two evenly divided,staggered rows in the center of the sheet.
Membrane: One ply of Flintlastic FR Cap 30,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium
FR-P or Flintlastic GMS adhered to the base sheet with approved mopping asphalt applied
within the EVT range and at a rate of 20-401bs/sq. or one ply of Flintlastic FR Cap 30 T,torch-
applied to base sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf(See General Limitation#9)
Pressure:
NOA No.: 18-1127.18
MIAM4UADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
i
Page 26 of 49
I
Membrane Type: APP Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32 or greater plywood or wood plank attached with 8d ring shank nails spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(3): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of All Weather/Empire Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet,Glasbase Base
Sheet or Flintglas Premium Ply 6 mechanically attached as detailed below.
Fastening#1: Base sheet shall be lapped 4" and fastened with 11 ga. annular ring shank nails and approved tin
caps 8"o.c. in the lap and three rows staggered in the center of the sheet 8"o.c.
Ply Sheet: One ply of All Weather/Empire Base Sheet,Flintlastic Ultra Poly SMS Base Sheet,Glasbase
(Optional) Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or one
or more plies of Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to the base sheet in a full
mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq.or one
ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered or Flintlastic STA
or Flintlastic APP Base T torch adhered.
Membrane: Flintlastic GTA or Flintlastic GTA-FR torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI-DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 27 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank attached with 8d ring shank nails spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(4): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of All Weather/Empire Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet, Glasbase Base
Sheet or Flintglas Premium Ply 6 mechanically attached as detailed below.
Fastening#1: Base sheet shall be lapped 4" and fastened with 11 ga.annular ring shank nails and approved tin
caps 8"o.c. in the lap and three rows staggered in the center of the sheet 8"o.c:
Ply Sheet: One ply of All Weather/Empire Base Sheet,Flintlastic Ultra Poly SMS Base Sheet,Glasbase
(Optional) Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or one
or more plies of Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to the base sheet in a full
mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. or one
ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered or Flintlastic Ultra
Poly SMS Base Sheet torch adhered.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR
Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI•DADE CouNIY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 28 of 49
i
i
I
Membrane Type: SBS Modified
Deck Type 1: wood,Non-Insulated
Deck Description: 15/32" or greater CDX plywood or wood plank attached with#8d ring shank nails spaced 6"o.c.
at wood joists spaced 24"o.c.
System Type E(5): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet or Yosemite Venting Base Sheet,mechanically attached as
described below.
Fastening#1: Fastened with FBC HVHZ nails and tin caps spaced 6"o.c.at the 3"lap and 6"o.c.in four,
equally spaced staggered center rows.
Ply Sheet: One or more plies of Glasbase Base Sheet,All Weather/Empire Base Sheet,Flexiglas Base
(Optional) Sheet;Flintlastic Base 20,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base
Sheet adhered to the base sheet in a full mopping of approved asphalt applied within the EVT
range and at a rate of 20-40 lbs./sq.or one or more plies of Flintlastic Base 20 T or Flintlastic
Ultra Poly SMS Base Sheet,torch applied.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or one ply of
Flintlastic FR Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf. (See General Limitation#7)
Pressure:
j NOA No.: 18-1127.18
MIAMI•UADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 29 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood;Non-Insulated
Deck Description: 15/32" or greater APA rated CDX plywood or wood plank attached with 8d ring shank nails
spaced 6"o.c.at wood joists spaced maximum 24"o.c.
System Type E(6): Base sheet mechanically fastened
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20,Yosemite Venting
Base,Flintlastic Poly SMS Base and Flintlastic Ultra Poly SMS Base,mechanically attached as
described below.
Fastening#1: Trufast#12 DP Fasteners or Trufast#14 HD Fasteners with Trufast 3 Metal Insulation Plates,
F1intFast#12 fasteners or F1intFast#14 fasteners with FlintFast 3"Insulation Plates spaced 8"
o.c.at the 4"wide laps and 8"o.c.in three,equally spaced staggered center rows.
Ply Sheet One ply of Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS
(Optional): Base Sheet applied in FlintBond Brush at a rate of 1.0— 1.5 gal/sq.to the base sheet.
Membrane: One ply of Flintlastic Cap 30,Flintlastic FR Cap 30,Flintlastic FR Dual Cap,Flintlastic FR-P,
Flintlastic Premium FR-P or Flintlastic GMS applied in FlintBond Brush at a rate of 1.0— 1.5
gal/sq to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI-DADS COUNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 30 of 49
I
Membrane Type: SBS Modified
Deck Type 1: Wood;Non-Insulated
Deck Description: 19/32"or greater plywood or wood plank attached with 8d ring shank nails spaced 4"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(8): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of All Weather/Empire Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base Sheet, Glasbase Base
Sheet or Flintglas Premium Ply 6 mechanically attached as detailed below.
Fastening#1: Base sheet shall be lapped 4"and fastened with 11 ga. annular ring shank nails and approved tin
caps 8"o.c. in the lap and three rows staggered in the center of the sheet 8"o.c.
Ply Sheet: One ply of All Weather/Empire Base Sheet,Flintlastic Ultra Poly SMS Base Sheet, Glasbase
(Optional) Base Sheet,Flexiglas Base Sheet,Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or one
or more plies of Flintglas Ply 4 or Flintglas Premium Ply 6 adhered to the base sheet in a full
mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq.or one
ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered or Flintlastic Ultra
Poly SMS Base Sheet torch adhered.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 401bs./sq. or Flintlastic FR
Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -60 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
QMIAMI-DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 32 of 49
i
i
Membrane Type: SBS Modified
Deck Type 1: wood,,Non-Insulated
Deck Description: 19/32"or greater plywood or wood plank attached with#8 wood screws spaced 6"o.c. at wood
joists spaced at maximum 24"o.c.
System Type E(9): Base sheet mechanically fastened
All General and System Limitations apply.
Separation Sheet: One or more plies of Glasbase Base Sheet,loose laid.
(Optional)
Base Sheet: One or more plies of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexibase Base
Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base
Sheet,mechanically attached as described below.
Fastening#1: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 6"o.c.at the 3"lap
and 6"o.c.in four,equally spaced staggered center rows.
Ply Sheet: One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA,self-adhered to the base
sheet.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to ply sheet with approved mopping
asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR Cap 30
T torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -60 psf (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAM4DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 33 of 49
i
Membrane Type: APP Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/3295 or greater plywood or wood plank attached with #8 wood screws spaced 6"o.c. at wood
joists spaced maximum 24"o.c.
System Type E(10): Base sheet mechanically fastened
All General and System Limitations apply.
Separation Sheet: One or more plies of Glasbase Base Sheet,loose laid.
(Optional)
Base Sheet: One or more plies of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexibase Base
Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base
Sheet,mechanically attached as described below.
Fastening#1: Anchor sheet shall be fastened with FBC HVHZ nails and tin caps spaced 6"o.c. at the 3"lap
and 6"o.c. in four, equally spaced staggered center rows.
Ply Sheet: One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA, self-adhered to the base
sheet.
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FR torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -60 psf (See General Limitation#7)
Pressure:
NOA No.:18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 34 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32 i or greater plywood or wood plank attached with 8d ring shank nails spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(11): Base sheet mechanically fastened
All General and System Limitations apply.
Separation Sheet: One or more plies of Glasbase Base Sheet,loose laid.
(Optional)
Base Sheet: One or more plies of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base Sheet,
Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet,
mechanically attached as described below.
Fastening#1: OMG#12 Standard Roofgrip fasteners with OMG 3"Galvanized Steel Plates or AccuTrac
Plates or Trufast#12 DP fasteners with Trufast 3"Metal Insulation Plates or Flintfast#12
fasteners with Flintfast 3"Insulation Plates spaced 7"o.c. at the 4"wide laps and 7"o.c. in two,
equally spaced staggered center rows.
Ply Sheet: One ply of Flintlastic Ultra Glass SA, self-adhered to the base sheet.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to ply sheet with approved mopping
asphalt applied within the EVT range and at a rate of 20 to 401bs./sq. or Flintlastic FR Cap 30
T torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -67.5 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 35 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 15/32° or greater APA rated plywood or wood plank attached with#8 screws spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(12): Base sheet mechanically fastened
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet,Yosemite Venting Base Sheet,All Weather/Empire Base
Sheet,Flexiglas Base Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic
Ultra Poly SMS Base Sheet,mechanically attached as described below.
Fastening#1: Cap nails: 1"diameter,0.032"thick metal cap with 0.120"shank diameter,annular ring shank
nails spaced 6"o.c.at the 4"wide laps and 6"o.c. in five,equally spaced staggered center rows.
i
Ply Sheet One 1PY of Glasbase Base Sheet,All Weather/Empire Base Sheet,Flexiglas Base Sheet,
(Optional): Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet
adhered to base sheet in a full mopping of approved asphalt applied within the EVT range and
at a rate of 20-401bs./sq. or one ply of Glasbase Base Sheet,All Weather/Empire Base Sheet,
Flexiglas Base Sheet,Flintlastic Base 20,Flintlastic Base 20 T or Flintlastic Ultra Poly SMS
Base torch applied to base sheet.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 401bs./sq. or one ply of
Flintlastic FR Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -67.5 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI•DAD,COUNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
I ,
Page 36 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 11/32"'or greater plywood or wood plank attached with#8 wood screws spaced 6"o.c. at wood
joists spaced maximum 24"o.c.
System Type E(13): Base sheet mechanically fastened
All General and System Limitations apply.
Base Sheet: One or more layers of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra Poly SMS Base
Sheet or All Weather/Empire Base Sheet,mechanically attached as described below.
Fastening#1: Anchor sheet shall be fastened with HVHZ nails and tin caps spaced 6"o.c. at the 3"lap and 6
o.c. in four,equally spaced staggered center rows.
Ply Sheet: One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered to the base
sheet.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to ply sheet with approved mopping
asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR Cap 30
T torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -82.5 psf (See General Limitation#7)
Pressure:
i
NOA No.: 18-1127.18
MIAMI•DAD,COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 37 of 49
Membrane Type: APP Modified
Deck Type 1: Wood;Non-Insulated
Deck Description: 19/32"or greater plywood or wood plank attached with#8 wood screws spaced 6"o.c. at wood
joists spaced maximum 24"o.c.
System Type E(14): Base sheet mechanically fastened
All General and System Limitations apply.
Base Sheet: One or more layers of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base
Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet,Flintlastic Ultra,Poly SMS Base
Sheet or All Weather/Empire Base Sheet,mechanically attached as described below.
Fastening#1: Anchor sheet shall be fastened with HVHZ nails and tin caps spaced 6"o.c. at the 3"lap and 3
o.c. in four, equally spaced staggered center rows.
Ply Sheet: One ply of Black Diamond Base Sheet, self-adhered to the base sheet.
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FR torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -82.5 psf (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAM4DADE COUNTY „ Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 3$of 49
i
I
i
i
Membrane Type: SBS Modified
Deck Type 1: Wooi,Non-Insulated
Deck Description: /32 for greater CDX plywood or wood plank attached with#10 wood screws spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(15): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base Sheet,All
Weather/Empire Base Sheet,Flintlastic Base 20 or Flintlastic Poly SMS Base Sheet
mechanically fastened with Simplex MAXX Cap fasteners spaced 6"o.c.in the 2"side lap and
6"o.c.in two evenly divided,staggered rows in the center of the sheet.
Membrane: One ply of Flintlastic FR Cap 30,Flintlastic FR Dual Cap,Flintlastic FR-P;Flintlastic Premium
FR-P,Flintlastic Cap 30 or Flintlastic GMS adhered to the base sheet with approved mopping
asphalt applied within the EVT range and at a rate of 2040 lbs/sq. or one ply of Flintlastic FR
Cap 30 T,torch-applied to base sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -90 psf. (See General Limitation#9)
Pressure:
NOA No.: 18-1127.18
MIAMI-DADE COUNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 39 of 49
Membrane Type: APP Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 15/32 or greater CDX plywood or wood plank attached with#10 wood screws spaced 6"o.c. at
wood joists spaced maximum 2V o.c.
System Type E(16): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Flintlastic APP Base T mechanically fastened with Simplex MAXX Cap fasteners
spaced 6"o.c.in the 2"side lap and 6"o.c. in two evenly divided, staggered rows in the center
of the sheet.
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FR,torch-applied to the base sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -90 psf. (See General Limitation#9)
Pressure:
NOA No.: 18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 40 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood,Non-Insulated
i
Deck Description: I5/3211,or greater CDX plywood or wood plank attached with#10 wood screws spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(17): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flintlastic Base 20,Flintlastic
Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet mechanically attached as
described below.
Fastening#1: Fastened with Trufast#12 DP Fastener or Trufast#14 HD Fastener with Trufast 3"Metal
Insulation Plate, OMG Heavy Duty fasteners with 3 in.Round Metal Plates,OMG AccutTrac
Hextra with AccuTrac Flat Bottom plates,FlintFast#12 fasteners or FlintFast#14 fasteners
with FlintFast 3"Insulation Plates spaced 6"o.c. at the 4"lap and 6"o.c.in three,equally
spaced staggered center rows.
Ply Sheet: One or more plies of Glasbase Base Sheet,All Weather/Empire Base Sheet,Flexiglas Base
(Optional) Sheet,Flintlastic Base 20,Flintlastic Ultra Poly SMS Base Sheet adhered to the base sheet in a
full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. or
one or more plies of Flintlastic Base 20 T or Flintlastic Ultra Poly SMS Base Sheet,torch
applied.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 401bs./sq. or one ply of
Flintlastic FR Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -97.5 psf. (See General Limitation#7)
Pressure:
MIAMI•DADe COUNTY NOA No.: 18-1127.18
Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 41 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood,Non-Insulated
i
Deck Description: 15/3211 or greater APA rated plywood or wood plank attached with#10 wood screws spaced
6"o.c.'at wood joists spaced maximum 24"o.c.
System Type E(18): Base sheet mechanically fastened
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet,Yosemite Venting Base Sheet,All Weather/Empire Base
Sheet,Flexiglas Base Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic
Ultra Poly SMS Base Sheet,mechanically attached as described below.
Fastening#1: Fastened with Trufast#14 HD Fasteners with Trufast 3"Metal Insulation Plates or F1intFast
#14 Fasteners with FlintFast 3"Insulation Plates spaced 8"o.c. at the 4"wide laps and 8"o.c.
in three, equally spaced staggered center rows.
Ply Sheet One ply of Glasbase Base Sheet,All Weather/Empire Base Sheet,Flexiglas Base Sheet,
(Optional): Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet
adhered to base sheet in a full mopping of approved asphalt applied within the EVT range and
at a rate of 20-40 lbs./sq. or one ply of Glasbase Base Sheet,All Weather/Empire Base Sheet,
Flexiglas Base Sheet,Flintlastic Base 20,Flintlastic Base 20 T or Flintlastic Ultra Poly SMS
Base torch applied to base sheet or one ply of Black Diamond Base Sheet or Flintlastic Ultra
Glass SA self-adhered to base sheet.
I
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or one ply of
Flintlastic FR Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -97.5 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
IIAMI•DA C000UNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 42 of 49
i
I :
i
Membrane Type: SBS Modified
Deck Type 1: Wood;Non-Insulated
Deck Description: 15/32" or greater CDX plywood or wood plank attached with#10 wood screws spaced 4"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(19): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base Sheet,All
Weather/Empire Base Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet
mechanically fastened with Simplex MAXX Cap fasteners spaced 6"o.c. in the 2"side lap and
6"o.c.in three evenly divided,staggered rows in the center of the sheet.
Membrane: One ply of Flintlastic FR Cap 30,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium
FR-P,Flintlastic Cap 30 or Flintlastic GMS adhered to the base sheet with approved mopping
asphalt applied within the EVT range and at a rate of 20-40 lbs/sq. or one ply of Flintlastic FR
Cap 30 T,torch-applied.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -105 psf. (See General Limitation#9)
Pressure:
i
I
NOA No.:18-1127.18
MA MI•Daoe COU rY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 43 of 49
i
I
Membrane Type: APP Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 15/32" or greater CDX plywood or wood plank attached with#10 wood screws spaced 4"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(20): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Flintlastic APP Base T mechanically fastened with Simplex MAXX Cap fasteners
spaced 6"o.c.in the 2"side lap and 6"o.c. in three evenly divided, staggered rows in the center
of the sheet.
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FR,torch-applied to the base sheet.
Surfacing: An of the approved surfacing/coating coatin options listed in Table 4.
g Y PP � g P
(Optional)
Maximum Design -105 psf. (See General Limitation#9)
Pressure:
NOA No.: 18 1127.18
MIAMI•DAne COUNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 44 of 49
I
Membrane Type: SBS Modified
Deck Type 1: Wood;Non Insulated
Deck Description: 19/32"or greater plywood or wood plank attached with#8 wood screws spaced 6"o.c. at wood
joists spaced maximum 24"o.c.
System Type E(21): Base sheet mechanically fastened
All General and System Limitations apply.
Base Sheet: One or more plies of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexiglas Base Sheet,
Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet,
mechanically attached as described below.
Fastening#1: Base sheet shall be fastened with OMG 12 Standard Roofgrip fasteners with OMG 3 in. Round
Metal Plates or AccuTrac Plates or Trufast#12 DP fasteners with Trufast 3"Metal Insulation
Plates or F1intFast#12 Fasteners with FhntFast 3"Insulation Plates spaced 7"o.c.at the 4"lap
and 7 o.c. in three,equally spaced center rows.
Ply Sheet: One ply o 1 f Black Diamond Base Sheet or Flintlastic Ultra Glass SA self-adhered to the base
a
sheet.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to ply sheet with approved mopping
asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR Cap 30
T torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -105.0 psf (See General Limitation#7)
Pressure:
i
NOA No.: 18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 45 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood,;Non-Insulated
Deck Description: 19/32"or greater plywood or wood plank attached with #8 wood screws spaced 6"o.c. at wood
joists spaced maximum 24"o.c.
System Type E(22): Base sheet mechanically fastened
All General and System Limitations apply.
Separation Sheet: One ply of Glasbase Base Sheet, loose laid.
(Optional)
Base Sheet: One or more plies of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexibase Base
Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base
Sheet,mechanically attached as described below.
Fastening#1: Base sheet shall be fastened with FBC HVHZ nails and tin caps.spaced 4"o.c. at the 3"lap and
4"o.c. in four,equally spaced center rows.
Ply Sheet: One ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA, self-adhered to the base
sheet.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR-P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to ply sheet with approved mopping
asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR Cap 30
T torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -105 psf (See General Limitation#7)
Pressure:
i
NOA No.: 18-1127.18
MIAMI-DADe COUNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 46 of 49
I ;
Membrane Type: APP Modified
Deck Type 1: Wood,Non-Insulated
Deck Description: 19/32"or greater plywood or wood plank attached with#8 wood screws spaced 6"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(23): Base sheet mechanically fastened
All General and System Limitations apply.
Separation Sheet: One ply of Glasbase Base Sheet,loose laid.
(Optional)
Base Sheet: One or more plies of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flexibase Base
Sheet,Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS
Base Sheet,mechanically attached as described below.
Fastening#1: Base sheet shall be fastened with FBC HVHZ nails and tin caps spaced 4"o.c. at the 3"
lap and 4"o.c.in four, equally spaced center rows.
Ply Sheet: One ply of Black Diamond Base Sheet, self-adhered to the base sheet.
Membrane: One ply of Flintlastic GTA or Flintlastic GTA-FR torch adhered to ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -105 psf (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI•DADE COUNTY Expiration Date: 06/19/23
Approval Date: 01/17/19
Page 47 of 49
Membrane Type: SBS Modified
Deck Type 1: Wood;Non-Insulated
Deck Description: 15/32" or greater CDX plywood or wood plank attached with#10 wood screws spaced 4"o.c. at
wood joists spaced maximum 24"o.c.
System Type E(24): Base sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of Glasbase Base Sheet,Yosemite Venting Base Sheet,Flintlastic Base 20,Flintlastic
Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base Sheet mechanically attached as
described below.
Fastening#1: Fastened with Trufast#12 DP Fastener or Trufast#14 HD Fastener with Trufast 3"Metal
Insulation Plate,OMG Heavy Duty fasteners with 3 in.Round Metal Plates,OMG AccutTrac
Hextra with AccuTrac Flat Bottom plates,F1intFast#12 fasteners or F1intFast#14 fasteners
with F1intFast 3"Insulation Plates spaced 6"o.c. at the 4"lap and 6"o.c. in four, equally
spaced staggered center rows.
Ply Sheet: One or more plies of Glasbase Base Sheet,All Weather/Empire Base Sheet,Flexiglas Base
(Optional) Sheet,./Flintlastic Base 20,Flintlastic Poly SMS Base Sheet or Flintlastic Ultra Poly SMS Base
Sheet adhered to the base sheet in a full mopping of approved asphalt applied within the EVT
range and at a rate of 20-401bs./sq. or one or more plies of Flintlastic Base 20 T or Flintlastic
Ultra Poly SMS Base Sheet,torch applied.
Membrane: One ply of Flintlastic GMS,Flintlastic FR Dual Cap,Flintlastic FR P,Flintlastic Premium FR-
P,Flintlastic Cap 30 or Flintlastic FR Cap 30 adhered to base or ply sheet with approved
mopping asphalt applied within the EVT range and at a rate of 20 to 40 lbs./sq. or one ply of
Flintlastic FR Cap 30 T torch adhered to base or ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -127.5 psf. (See General Limitation#7)
Pressure:
NOA No.: 18-1127.18
MIAMI-DADEcouNTY Expiration Date: 06/19/23
Approval Date:01/17/19
Page 48 of 49
I
WOOD DECK SYSTEM LmTATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LLMTATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 20-40 lbs./sq.,or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4'x 4'maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot
mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at
each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of 45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force(F')value of 2751bf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value,as field-tested,are below
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required,as determined by the Building Official,a revised fastener spacing,
prepared, signed and sealed by a Florida registered Professional Engineer,Registered Architect,or Registered
Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value
taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application
Standard RAS 117.
7. Perimeter and comer areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA,General Limitation#9 will not be applicable.)
8. All attachment and sizing of perimeter nailers,metal profile,and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones(i.e. field,
perimeters,and comers).Neither rational analysis,nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones(i.e.perimeters, extended comers and comers). (When this limitation is specifically
referred within this NOA,General Limitation#7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 18-1127.18
Mwr�i naoe courvr�r Expiration Date: 06/19/23
Approval Date:01/17/19
Page 49 of 49