The URL can be used to link to this page

Home My WebLink AboutIntegrated Security FPL Interstate Solar Data SheetsJune 2017 1/2 www.lifesafetypower.com Overview MCLASS™ Unified Power Systems combine FlexPower® power modules alongside Mercury Security™ access hardware in one compact and secure UL Listed solution. This unit is a 12V and 24V DC dual voltage access power system. C8 lock control module provide eight access control inputs capable of voltage or dry contact activation, and eight outputs programmable for failsafe / failsecure operation at either 12 or 24 VDC and controlled by the integrated fire alarm interface circuit on the FPO. D8P module provides eight auxiliary class II outputs and each output is configurable for 12 or 24VDC operation. MCLASS enclosures are painted steel with removable backplate and include lock, two (2) keys and tamper switch. Input Power Input 120/230 VAC 50/60 Hz | 170 Watts (1.41 Amps) Overload and short circuit protection Over temperature protection Polarized AC power supply disconnect Output Power 4A@12V and 4A@24V DC, 150W maximum combined output power Outputs: Continuous (DC1) Resettable DC2) 8 auxiliary outputs, class II rated at 2.5 Amps per output 8 control outputs, fuse rated at 3.0 Amps per output 120 mV output voltage ripple System Efficiency: 88% | System BTU Rating: 66 BTU/Hr Battery Charging Independent built-in 2A charger for sealed lead acid or gel type batteries Microprocessor dual rate charging of 12 or 24 V battery sets Charges up to 80Ah battery sets within UL limit Automatic switchover to standby battery when AC fails Zero voltage drop when switched over to battery backup Supervision AC Fail (form "C" contacts) System Fault (form "C" contacts) may be triggered by low/no battery, short to earth ground, power supply failure or blown fuse Visual Indicators AC input, DC1 and DC2 output System fault / AC fault | Short to earth ground | Reverse battery polarity Fire Alarm Input activated B100: DC input, output and Fault C8: DC input, output and Fault / D8P: DC outputs Regulatory Compliance Mercury/LSP Joint Listing UL294, UL603, UL1076, ULC S318, ULC S319 CSA C22.2 #107.1, CSA 22.2 #60950 CSFM / FCC Part 15, Subpart B CE Enclosure Dimensions Size: 24.00H x 20.00W x 4.50D in. (61.00 x 50.00 x 11.50 cm) | Weight: 25 lbs. Access Panel Mounting EP1501, EP1502, EP4502, EP2500, MR50, MR51e, MR52, MR16, LNL-500, 1100, 1200, 1300, 1320, 2000, 2210, 2220, 3300 Enclosure Features Labor saving design –Pre-wired power section –Pre-punched knockouts –Removeable backplate simplifies installs –Pre-defined hole pattern for power section –Access panels mount on threaded standoffs - no drilling required Additional benefits –Wire management room –4.5" enclosure depth fits battery set –Tamper switch, lock, dual key set standard –Mounting hardware for access boards included System Features FPO offline power supply –120 or 230 VAC input –12 or 24 VDC outputs –On board Fire Alarm Interface –Continuous and resettable DC Distributed outputs –Eight auxiliary - class II at 2.5A each –Eight lock control - fused at 3A each Expansion options –Increased power, multiple voltages –Additional distribution outputs –Network monitoring and reporting Lifetime Warranty Specifications FLEXPOWER FPO150-B100C8D8PE4M1 MCLASS™ UNIFIED POWER SYSTEM 150W / 12 & 24VDC / 8-16 Doors 8 Lock / 8 Auxiliary Outputs FLEXPOWER UNIFIED POWER SOLUTIONS UNIFIEDPOWERLISTED Ordering Description FPO150-B100C8D8PE4M1 150W (12V & 24V) 8 lock / 8 aux outputs, MCLASS encl June 2017 2/2 www.lifesafetypower.com FLEXPOWER FPO150-B100C8D8PE4M1 LifeSafety Power, Inc. 304 Terrace Drive Mundelein, IL 60060 USA lifesafetypower.com (888) 577-2898 info@lifesafetypower.com Specifications subject to change without notice. © 2017 LifeSafety Power Inc. All rights reserved. LifeSafety Power and FlexPower are registered trade- marks of LifeSafety Power Inc. This literature is for guidance only. It does not constitute recommenda- tions, representation, or advice, nor is it part of any contract. Our policy is one of continuous product improvement, and the right is reserved to modify the specifications contained herein without notice. P01-584 06/17 E4M1 EXPANDS SIX MR52 TO DOOR E4M2 ON DOOR ONLY E4M2 TWO VERTICAL UNIVERSAL MERCURY PATTERN all boards each slot (1) MR52 / EP1502 (1) EP2500 (2) EP1501 / Mr51E (2) MR50 Universal Mercury Mounting Pattern Mercury Slots w/Power Slots all Mercury MR52 / EPxx 4 6 MR16in / MR16out 4 6 EP2500 / MUX8 4 6 EP1501 / MR51e 8 12 MR50 8 12 Mercury Slots w/Power Slots all Mercury MR52 / EPxx 10 12 MR16in / MR16out 10 12 EP2500 / MUX8 4 6 EP1501 / MR51e 8 12 MR50 8 12 E4M E4M1(adds six MR door panels) Access Hardware LNL-X2220 Intelligent Dual Reader Controller Lenel.com/access-hardware Overview The LNL-X2220 Intelligent Dual Reader Controller (IDRC) provides a single board solution for interfacing one or two doors to an OnGuard® system. In addition, other I/O and reader interface modules can be added on the controller’s downstream port to expand its capabilities. The LNL-X2220 controller revolutionizes access control system architecture by allowing Ethernet connection directly from an entry location to the OnGuard server, while still providing the security, functionality, and modularity of Lenel’s proven hardware platform. The LNL-X2220 controller is scalable for any access control application, from the most basic to the most sophisticated. In the event of communication loss, the LNL-X2220 controller allows nearly all local functionality to continue unimpaired until the server connection is restored. Utilizing its native Ethernet communications and an advanced 32-bit processor, the LNL-X2220 controller can communicate upstream to the host computer through its Ethernet port. The controller can store up to 250,000 cardholders in non-volatile flash memory, and supports selective download for larger cardholder databases. The downstream RS-485 two-wire port can be used to connect up to 32 devices (maximum 64 doors). Two on-board reader ports support Data1/Data0, Clock/Data, Supervised and Unsupervised F2F, Biometric readers and the bi-directional RS-485 Open Supervised Device Protocol (OSDP) communications. Each LNL-X2220 controller supports up to sixteen different card formats. The LNL-X2220 controller includes eight inputs that support normally open, normally closed, supervised, and unsupervised circuits. In addition, four output relays support fail-safe or fail-secure operation. Features & Functionality Controller Functionality • DNS device naming through DHCP extended commands • 6 MB of available on-board, non-volatile flash memory • Battery-backed, non-volatile storage of 50,000 events • Configurable option for Data at Rest encryption • Firmware stored in flash memory, background download of firmware updates supported • Supports up to sixteen badge formats • Biometric template storage support for OSDP™ Biometric and legacy Bioscrypt® readers • Optional Secondary NIC, USB port (2.0) with optional adapter • Enhanced anti-passback capabilities • Up to 32,000 access level permissions • Elevator control support for up to 128 floors • Individual extended held open and strike times • Two dedicated inputs for tamper and power failure status • Advanced Encryption Standard (AES) 256-bit algorithm for communications to Lenel Series 3 reader and I/O modules; AES 128 bit encryption to Lenel Series 2 reader and I/O modules • AES128 or TLS 1.2 (with AES256 support) communication to OnGuard • RNDIS support enables USB connection to display controller web configuration pages Reader Interface Functionality • Supports Data 1/Data0, Clock/Data, Supervised and Unsupervised F2F and OSDP-compatible RS-485 readers and keypads • Support for OSDP Biometric template transfer and Secure Channel Encryption • Door contact supervision (open/closed) and REX push-button monitor for each door Lenel® Controller LNL-X2220 Parts and Spare PartsSpecifications Part No.Description LNL-X2220 6 MB on-board flash memory available for cardholder database; 50,000 event battery backed RAM for event log. USB2- OTGE100 USB to Ethernet converter, for LNL-X Series Controllers only. Provides optional Secondary NIC connection. Second NIC should be on different subnet than primary NIC. System Diagram Primary Power 12 to 24 VDC ± 10%, 500 mA maximum (reader current not included) Reader Ports 600 mA maximum (add 600 mA to primary power current) Primary Host Communication Ethernet: 10-BaseT/100Base-TX Secondary Host Communication USB port (2.0) with optional adapter: pluggable model USB2-OTGE100 Serial I/O Device One each: 2-wire RS-485, 2,400 to 115,200 bps, asynchronous, half-duplex, 1 start bit, 8 data bits, and 1 stop bit Inputs Eight unsupervised / supervised, standard EOL: 1k/1k ohm, 1% 1/4 watt; two unsupervised inputs dedicated for cabinet tamper and UPS fault monitoring Outputs Four relays: Normally open contact (NO): 5 A @ 30 VDC resistive; Normally closed contact (NC): 3 A @ 30 VDC resistive Reader Interface Power 12 VDC ± 10% regulated, 300 mA maximum each reader (input voltage [VIN] must be greater than 20 VDC) or 12 to 24 VDC ± 10% (input voltage passed through), 300 mA maximum each reader Data Inputs TTL compatible, F/2F or 2-wire RS-485 RS-485 Mode 9,600 to 115,200 bps, asynchronous, half-duplex, 1 start bit, 8 data bits, and 1 stop bit. Maximum cable length: 2,000 ft. (609.6m) LED Output TTL levels, high > 3 V, low < 0.5 V, 5 mA source/sink maximum Buzzer Output Open collector, 12 VDC open circuit maximum, 40 mA sink maximum Cable Requirements Power and Relays One twisted pair, 18 to 16 AWG Ethernet CAT-5, minimum TTL Reader 22 to 16 AWG, depending on length and requirements Alarm Input One twisted pair, 30 ohms maximum, typically 22 AWG @ 1,000 ft. (304.8m) RS-485 I/O Device Port One twisted pair with drain wire and shield, 120 ohm impedance, 24 AWG, 4,000 ft. (1,219m) maximum RS-485 Reader Port One twisted pair with drain wire and shield, 120 ohm impedance, 24 AWG, 2,000 ft. (610m) maximum Mechanical Dimensions 8.0 W x 6.0 L x 1.0 H in. (203.2 x 152.4 x 25mm) Weight 9.0 oz. (255g) nominal, board only Environmental Temperature -55° to +85° C, storage 0° to +70° C, operating Humidity 5 to 95% RHNC Heat Output (BTUs)at 12 VDC, 20.5 BTU/hr at 24 VDC, 22.9 BTU/hr Approvals FCC Part 15, CE, RoHS, UL 294, UL 1076, CAN/ULC 60839-11-1:2016, CSA C22.2 No. 205-1983, cUL/ORD-C1076 The interface is for use in low voltage, Class 2 Circuits only. The installation of this device must comply with all local fire and electrical codes. LenelS2.com (866) 788-5095 Specifications subject to change without notice. ©2018 United Technologies Corporation. All rights reserved. All trademarks are the property of their respective owners. LenelS2 is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. 2018/11 (GSP-2716) LNL-1300 Single Reader Interface Module LNL-1100 Input Control Module Up to 16 Inputs per LNL-1100 Motion Sensor Alarm LNL-1200 Output Control Module Up to 16 Outputs per LNL-1200 RS-485 Multi-drop up to 4000 ft. ReaderReaderReader LNL-X2220 Intelligent System Controller (ISC) Max 32 Devices TCP/IP NETWORKOnGuard® Security Server Option 2.1 -OR- Reader Reader Option 2.2 Reader Reader LNL-1320 Dual Reader Interface Module Access Hardware LNL-1320 Series 3 Dual Reader Interface Module lenel.com/access-hardware Overview Lenel offers a Dual Reader Interface (DRI) module for access control solutions. Most access control card readers, keypads, or readers with keypads that use standard Wiegand Data1/ Data0 or Clock/Data communication are supported, as are those that support the bidirectional RS-485 Open Supervised Device Protocol (OSDP™). Lock, unlock, and facility code offline access modes are supported on all readers connected to the DRI. Each DRI supports up to 16 different card formats as well as issue codes for both magnetic and Wiegand card formats. The DRI provides a vital link between the Intelligent System Controller (ISC) and the card reader attached to the interface. As many as 32 DRI modules can be multidropped using RS- 485 2-wire or 4-wire communication up to 4,000 feet per port away from the ISC. Each DRI module is individually addressed for increased reporting capabilities with OnGuard® access control software applications. The DRI includes eight inputs that support normally open, normally closed, supervised, and non-supervised circuits. In addition, six output relays support fail-safe or fail-secure operation. Features & Functionality • 12 or 24 VDC power supply • Supports Data1/Data0, Clock/Data, Supervised and Unsupervised F2F and OSDP-compatible RS-485 readers and keypads • Supports Open Supervised Device Protocol (OSDP) readers, including biometric template transfer and Secure Channel encryption • Downloadable firmware • Six Form-C 5 A at 28 VDC relay outputs • Up to 16 different formats • Issue code support for magnetic and Wiegand formats • Door contact supervision (open/closed) • REX push-button monitor • Strike control output • Bicolor reader status LED support and 2-wire LED support • Beeper control • Dedicated tamper and power failure circuits • Support for offline reader access mode • On-board jumpers for termination • On-board regulator allows 12 VDC reader support from 24 VDC power source • DIP switch-selectable addressing • Advanced Encryption Standard (AES) 128-bit or 256-bit encryption supported, depending on ISC and OnGuard version • Supports Schlage® Handkey® template download • Compatible with current and previous versions of OnGuard Extended Functionality • Connect FIPS-201 readers for embedded authentication (when used with LNL-4420 and appropriate HID® and OnGuard software and licenses) lenel.com (866) 788-5095 Specifications subject to change without notice. ©2017 United Technologies Corporation. All rights reserved. All trademarks are the property of their respective owners. Lenel is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. 2017/12 (GSP-2463) LNL-1320 Series 3 Specifications Primary Power 12 to 24Vdc ±10%, 550mA maximum (plus reader current) 12Vdc @ 550mA (plus reader current) maximum, 22.5 BTUs 24Vdc @ 330mA (plus reader current) maximum, 27.0 BTUs Outputs 6 outputs, Form-C contacts: Normally Open (NO) Contact: 5A @ 30 Vdc, Normally Closed (NC) Contact: 3A @ 30 Vdc Inputs 8 unsupervised/supervised, standard EOL: 1k/1k ohm, 1% 1/4 watt 2 unsupervised, dedicated for cabinet tamper and UPS fault monitoring Reader Interface Reader power: 12Vdc ±10% regulated, 300mA maximum each reader (jumper selectable and input voltage (VIN) must be 20Vdc minimum) or 12 to 24Vdc ±10% (input voltage passed through) 300mA maximum each reader Reader Port Compatibility Wiegand Data 1/Data 0 Magnetic Clock/Data Supervised and Unsupervised F2F Open Supervised Device Protocol Mechanical Dimension: 6” (152mm)W x 8” (203mm)L x 1” (25mm)H Weight: 11 oz. (312g) nominal Environmental Temperature Operating: 32°F to 158°F (0°C to +70°C) Storage: -67°F to 185°F (-55°C to +85°C) Humidity 5% to 95% RHNC Compliance Approvals FCC Part 15, CE, RoHS, UL 294, UL 1076, ULC CSA-C22.2, CAN/ULC-S319-05, cUL/ORD-C1076 Intelligent System Controller (ISC) Capacity varies per ISC model* LNL-1320 Dual Reader Interface Module LNL-1300 Single Reader Interface Module LNL-1100 Input Control Module Up to 16 Inputs per LNL-1100 Motion Sensor Alarm LNL-1200 Output Control Module Up to 16 Outputs per LNL-1200 RS-485 Multi-drop up to 4000 ft. Option 1TCP/IP NETWORKReader Reader Reader Option 2 OnGuard® Security Server -OR- * See ISC datasheets for specic capacities. Power Supplies & Enclosures LNL-AL400ULX UL Listed 4A, 110VAC Power Supply – 12VDC 4A output, 115VAC input, continuous supply cur- rent with enclosure (15.5” x 12.5” x 4.5”), lock, tamper switch, UPS capable (Battery Optional) UL & CUL Approved LNL-AL600ULX-4CB6 UL Listed Power Supply – 12VDC 6A output, 115VAC (1.6 amps) input, continuous supply current with enclosure (24” x 18” x 4.5”), lock, tamper switch, power distribution module, UPS capable (Battery Optional) UL & CUL Approved ABT-12 Battery Kit - 12VDC, 12 AH battery (PS-12120) System Diagram Access Hardware LNL-1200 Series 3 Output Control Module lenel.com/access-hardware Overview Series 3 Lenel® Output Control Module (OCM) communicates directly with the Intelligent System Controller (ISC) by either 2-wire or 4-wire RS-485 communication. Each OCM is an individually-addressed device, and counts as a single device on all Intelligent System Controllers. The OCM can be operated by either 12 or 24 VDC power. Each OCM includes dedicated tamper and power failure input contacts. The OCM has 16 programmable output relays that can be configured for fail-safe or fail-secure operation. Each relay supports the “On,” “Off,” and “Pulse” OnGuard® software commands. Features & Functionality • 16 Form-C 5 A, 30 VDC contacts for load switching • 12 or 24 VDC input power • 2 dedicated digital inputs for tamper and power failure status • RS-485 communication, multidropped (2-wire or 4-wire RS-485) • Up to 16 OCMs per Intelligent System Controller • On-board termination jumpers • DIP switch-selectable addressing • Status LEDs for communication to the host, heartbeat and relay status • Elevator control, support for 128 floors • Advanced Encryption Standard (AES) 128-bit or 256-bit encryption supported, depending on ISC and OnGuard version • Suitable as replacement for Series 1 and Series 2 boards lenel.com (866) 788-5095 Specifications subject to change without notice. ©2017 United Technologies Corporation. All rights reserved. All trademarks are the property of their respective owners. Lenel is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. 2017/12 (GSP-2463) LNL-1200 Series 3 Specifications Primary Power 12 to 24Vdc ±10%, 1100mA maximum 12Vdc @ 850mA nominal, 34.82 BTUs 24Vdc @ 450mA nominal, 36.82 BTUs Outputs 16 Form-C, 5A @ 30Vdc, resistive Inputs 2 unsupervised dedicated for cabinet tamper and UPS fault monitoring Mechanical Dimension: 6” (152mm)W x 8” (203mm)L x 1” (25.4mm)H Weight: 14 oz. (400g) nominal Environmental Temperature Operating: 32°F to 158°F (0°C to +70°C) Storage: -67°F to 185°F (-55°C to +85°C) Humidity 0% to 95% RHNC Compliance Approvals FCC Part 15, CE, RoHS, UL 294, UL 1076, ULC CSA-C22.2, CAN/ULC-S319-05, cUL/ORD-C1076 Power Supplies & Enclosures LNL-AL400ULX UL Listed 4A, 110VAC Power Supply – 12VDC 4A output, 115VAC input, continuous supply current with enclosure (15.5” x 12.5” x 4.5”), lock, tamper switch, UPS capable (Battery Optional) UL & CUL Approved LNL-AL600ULX-4CB6 UL Listed Power Supply – 12VDC 6A output, 115VAC (1.6 amps) input, continuous supply current with enclosure (24” x 18” x 4.5”), lock, tamper switch, power distribution module, UPS capable (Battery Optional) UL & CUL Approved ABT-12 Battery Kit - 12VDC, 12 AH battery (PS-12120) System Diagram Intelligent System Controller (ISC) Capacity varies per ISC model* LNL-1320 Dual Reader Interface Module LNL-1300 Single Reader Interface Module LNL-1100 Input Control Module Up to 16 Inputs per LNL-1100 Motion Sensor Alarm LNL-1200 Output Control Module Up to 16 Outputs per LNL-1200 RS-485 Multi-drop up to 4000 ft. Option 1TCP/IP NETWORKReader Reader Reader Option 2 OnGuard® Security Server -OR- * See ISC datasheets for specic capacities. Access Hardware LNL-1100 Series 3 Input Control Module lenel.com/access-hardware Overview Series 3 Lenel® Input Control Module (ICM) provides the access control system with high-speed acknowledgement of critical alarm points in monitored areas. The ICM communicates directly with the Intelligent System Controller (ISC) by either 2-wire or 4-wire RS-485 communication. The ICM has 16 configurable input control points and 2 output control relays. It supports normally open, normally closed, supervised and non- supervised circuits. The input circuits are scanned using an analog-to-digital converter. The digitized input status signal is software- monitored and controlled, so that each input point can be programmed as a supervised or non-supervised alarm point. The output relays can also be configured for fail-safe or fail- secure operation. Each realy supports the “On,” “Off,” and “Pulse” Lenel OnGuard® software commands. Features & Functionality • Grade B, A, and AA line supervision • 12 or 24 VDC input power • 16 programmable supervised or non-supervised contacts • 2 Form-C 5 A, 28 VDC contacts for load switching • 2 dedicated inputs for tamper and power failure status • On-board termination jumpers • DIP switch-selectable addressing • Elevator control, support for 128 floors • Status LED for host communication and heartbeat • Variable resistor values for line supervision • Downloadable firmware • Advanced Encryption Standard (AES) 128-bit or 256-bit encryption supported, depending on ISC and OnGuard version • Suitable as replacement for Series 1 and Series 2 boards lenel.com (866) 788-5095 Specifications subject to change without notice. ©2017 United Technologies Corporation. All rights reserved. All trademarks are the property of their respective owners. Lenel is a part of UTC Climate, Controls & Security, a unit of United Technologies Corporation. 2017/12 (GSP-2463) LNL-1100 Series 3 Specifications Primary Power 12 to 24Vdc ±10%, 350mA maximum 12Vdc @ 300mA nominal, 12.27 BTUs 24Vdc @ 220mA nominal, 18.00 BTUs Outputs 2 outputs, Form-C, 5A @ 28Vdc, resistive Inputs 16 unsupervised/supervised, standard EOL: 1K/1K ohm, 1%, 1/4 watt 2 unsupervised, dedicated for cabinet tamper and UPS fault monitoring Mechanical Dimension: 6” (152mm)W x 8” (203mm)L x 1” (25.4mm)H Weight: 9 oz. (250g) nominal Environmental Temperature Operating: 32°F to 158°F (0°C to +70°C) Storage: -67°F to 185°F (-55°C to +85°C) Humidity 0% to 95% RHNC Compliance Approvals FCC Part 15, CE, RoHS, UL 294, UL 1076, ULC CSA-C22.2, CAN/ULC-S319-05, cUL/ORD-C1076 Power Supplies & Enclosures LNL-AL400ULX UL Listed 4A, 110VAC Power Supply – 12VDC 4A output, 115VAC input, continuous supply current with enclosure (15.5” x 12.5” x 4.5”), lock, tamper switch, UPS capable (Battery Optional) UL & CUL Approved LNL-AL600ULX-4CB6 UL Listed Power Supply – 12VDC 6A output, 115VAC (1.6 amps) input, continuous supply current with enclosure (24” x 18” x 4.5”), lock, tamper switch, power distribution module, UPS capable (Battery Optional) UL & CUL Approved ABT-12 Battery Kit - 12VDC, 12 AH battery (PS-12120) System Diagram Intelligent System Controller (ISC) Capacity varies per ISC model* LNL-1320 Dual Reader Interface Module LNL-1300 Single Reader Interface Module LNL-1100 Input Control Module Up to 16 Inputs per LNL-1100 Motion Sensor Alarm LNL-1200 Output Control Module Up to 16 Outputs per LNL-1200 RS-485 Multi-drop up to 4000 ft. Option 1TCP/IP NETWORKReader Reader Reader Option 2 OnGuard® Security Server -OR- * See ISC datasheets for specic capacities. WWW.SDCSECURITY.COM ■ SECURITY DOOR CONTROLS Security Door Controls ACCESS & EGRESS SOLUTIONS - THE LOCK BEHIND THE SYSTEM 1 Electra™ Pro Electrified Cylindrical Locksets are designed for the access control of openings in commercial, industrial and institutional facilities where code compli- ance, dependable operation and resistance to physical abuse is required. ElectraTM Pro 7200 SeriesElectrified Cylindrical Locksets • Latch Status Output Standard with All Locksets • Optional Internal REX Available in Lieu of Latch Status • Dual Voltage 12 and 24VDC • Choice of Failsafe or Failsecure Operating Mode • Clutch Allows The Lever to Operate While The Door Stays Locked for Increased Vandal and Abuse Resistance • Independent Power Return Springs for Effective Lever Action and Prevention of Lever Sag • SDC Cylinder with ‘C’ Keyway • Small Format Interchangeable Core (Optional) • No Exposed Mounting Screws • Strikes Available to Match Existing Frame Preparation • Choice of Seven Architectural Finishes • Exceeds ANSI A156-2 Grade 1 Specifications • SDC Lever Handle Styles Comply with ADA Easy Access Requirements and CSFM, California State Fire Marshal, Title 19 • May Be Used in New or Retrofit Construction • Building and Fire Life Safety Code Compliance • Ideal for High Usage Environments • Retrofits Existing Mechanical Lock Prep FEATURES MODELS Z7250 Failsafe - Outside locked when energized, unlocked by an access control or key from the outside and rotating the inside lever pro- vides egress at all times Z7252 Failsecure - Outside locked when de-ener- gized. Unlocked by an access control or key from the outside and rotating the inside lever provides egress at all times 7200 Series Locksets are locked on the outside and unlocked from the exterior by an access control or mechan- ical key. The inside lever is always operable for uninhibited egress.ST A TE FIRE M A R SHALSTATE O F CALIFO R N IAS ERV I C ELI S TIN G CSFM LISTED 3774-0324-104 W ARRA N TYYEAR5S ELECT A B LEFIELD1224 SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM Security Door Controls ACCESS & EGRESS SOLUTIONS - THE LOCK BEHIND THE SYSTEM2 Z7250 SDC Failsafe, with Latch Status Output Z7252 SDC Failsecure, with Latch Status Output SPECIFICATIONS Voltage Dual 12/24VDC Input Current 600/300mA @ 12/24VDC Latch Status Output SPDT 3 Amps @ 30VDC Latch Bolt 9/16” Throw Backset 2-3/4” Strike 4-7/8” ANSI A115.2 Door Thickness 1-3/4” to 2-1/8” Weight 7.0 lbs BUILDING AND FIRE LIFE SAFETY CODE COMPLIANT Electra™ Pro electrified cylindrical locks ensure that the door stays latched even when unlocked, maintaining fire door integrity. Electra™ Pro locksets comply with all nation- al building and fire life safety code requirements for use on fire rated doors, including high-rise stairwell and elevator lobby doors where the use of electric strikes and magnetic locks is prohibited. SECURITY WITH SUPERIOR AESTHETICS Available in failsafe and failsecure modes to accommodate either security or fire life safety applications, Electra™ Pro Z7200 electrified locksets provide a superior appearance compared to exposed and vulnerable electric strikes and magnetic locks, while eliminating the need for request-to- exit devices. B1 2-3/4” Backset Latchbolt (Standard) 6| SPECIFY LATCH AND BACKSET ASSEMBLIES (OPTIONAL) ST1 ANSI 1-1/4” x 4-7/8” (Standard) ST2 T-Strike with Dust Box. 1-1/8” x 2-3/4” MUST BE SPECIFIED 7| SPECIFY STRIKE PLATES (OPTIONAL) G Galaxy G5 Galaxy I-Core prep E Eclipse E5 Eclipse I-Core prep HOW TO ORDER 1| SPECIFY MODEL 2| SPECIFY LEVER TRIM 3| SPECIFY FINIS H Q 626 Dull Chrome (Standard) C 605 Bright Brass H 613 Oil Rubbed Bronze D 606 Dull Brass P 625 Bright Chrome SDC Conventional Cylinders (Schlage “C” Keyway Standard) 6PKA 6 Pin Keyed alike 6PKD 6 Pin Keyed different (Standard) 5| SPECIFY CYLINDER Vandal Resistant Lever Handles Standard With SDC Brand Lockset When locked, the built-in clutch permits the handles to operate without retracting the latch, reduc- ing potential for damage. APPLICATIONS PRODUCT SKU SAMPLE: Z7250 E Q R 6PKA ACCESSORIES PTH-4Q Four Wire, Dull Chrome PTH-10Q Ten Wire, Dull Chrome PTH-2+4Q Six Wire Electric Hinge 1-pair 16 Amp inrush, 4 Amp continuous; 2 -pair 1 Amp @ 12/24V UL 10B Listed for 3hr Fire Rated Door OR SPECIFY I-CORES (OPTIONAL) [IC] Interchangeable Core - requires E5 or G5 lever trim (Best ‘A’ Keyway Standard)IC7P-KA 7 pin I-Core, Small Format, Keyed alike IC7P-KD 7 pin I-Core, Small Format, Keyed different 4| SPECIFY INSIDE REX (OPTIONAL) R Request-to-exit Output, operates on activation of inside lever, SPDT 0.1A @ 30VDC Overview Device types The 98/99 Series devices are heavy-duty push pads. The 98 Series has a smooth mechanism case, while the 99 Series has a grooved mechanism case. The 98/99 Series has been certified to the highest industry standards and are used in schools, hospitals and government buildings. Exit device 98/99 Series 99 Series features grooved mechanism case 98 Series features smooth mechanism case Rim device 75 Mortise lock device 47WDC Concealed vertical rod wood door device 1 27 Surface mounted vertical rod device 1 49 Concealed vertical cable device 2 47 Concealed vertical rod device, 5⁄16" throw 1 48 Concealed vertical rod device, 5⁄8" top, 1 1⁄2" bottom throw 50WDC Concealed vertical cable wood door device 57 Three-point latch device 1 Also available less bottom rod (LBR) 2 Also available less bottom latch (LBL) Trim functions 98/99 Series Exit device NL Night latch Key retracts latchbolt Rim and 1 ¼" mortise cylinder TP Thumbpiece Key locks and unlocks Rim and 1 ¼" mortise cylinder TPBE Thumbpiece, blank escutcheon Blank escutcheon always operable (no cylinder, use with DT trim) TL Turn lever Key locks and unlocks (use with DT trim) 1 ¼" mortise cylinder TLBE Turn lever, blank escutcheon Blank escutcheon always operable (no cylinder, use with DT trim) TLOP Turn lever, optional pull EO No outside trim Exit only DT Dummy trim Pull when dogged (not recommended for fire device) NLOP Night latch Key retracts latchbolt, pull required HL Hospital latch Key locks and unlocks 1 ¼" mortise cylinder LBE1 Lever, blank escutcheon KBE Knob, blank escutcheon Always operable (no cylinder) L Lever K Knob Key locks and unlocks Rim and 1 ¼" mortise cylinder Handed, reversible lever Electrified lever operation available LDT Lever, dummy trim KDT Knob, dummy trim Pull when dogged LNL Lever, night latch KNL Knob, night latch Key retracts latchbolt Rim and 1 ¼" mortise cylinder Handed, reversible lever Trim styles 98/99 Series Exit device Dimensions Trim style Width Height Thickness Projection 990 3" 14 3⁄16"3⁄32"2" 996 Knob 2 3⁄4" 10 3⁄4"27⁄32"3 1⁄4" 996 Lever 2 3⁄4" 10 3⁄4"27⁄32"2 7⁄8" 696 1 5⁄8" 13 1⁄2"3⁄16"2 1⁄6" 697 1 5⁄8" 13 1⁄2"3⁄16"3" 392-7 3⁄4" inch round stainless steel with 7" center to center that matches the 98/99 center case. 3 1⁄2" offset with 11⁄2" clearance. HL 2 9⁄16"7 7⁄8"- 2 5⁄8" 374 2 3⁄4" 10 3⁄4"27⁄32" VR910/914 with RIM/verticals 5 1⁄2" 11" - VR910/914 with mortise 7 1⁄4" 11" - 990 996 696 697 3/4" (19mm) diameter pull 392-7 HL 374 VR910 VR914 Overview E996L- Electrified breakaway lever trim E996L Electrified Breakaway lever trim provides remote locking and unlocking capabilities while incorporating the patented Breakaway trim design. The 24VDC solenoid can be energized from a distant controller, thus allowing access control of the opening. The control of stairwells in high-rise buildings is a common application for this trim. When electrically unlocked the unit operates as a normal lever trim. When electrically locked, the lever feels locked, but when more than 35 pounds of torque pressure is applied, the Breakaway lever feature engages. The E996L is available in standard either in a fail safe (FS) or fail secure (FSE) condition, but can also be field converted where allowed. The trim can be ordered with a device, added to an existing 98/99 series device application, or a conversion kit can be added to an existing 996L Breakaway lever trim. On new construction applications, the E996L trim will require less door prep. The E996L is available with a blank escutcheon (BE) function, or with cylinder operation for night latch (NL) function. The E996L electrified trim replaces the current “E” electric feature on 98/99 series rim devices. Consult factory for requirements. E7500- Electric mortise lock The electric mortise lock device has all the versatility and advantages of the standard mortise lock device, plus the advantage of being electrically controlled by a remote switching device, an access control system or an automatic fire alarm system. The device features the 7500 mortise lock. The E7500 controls the locking of the outside trim. When unlocked, the door remains latched, preserving the fire rating of the door and making it particularly useful where codes permit locking but require unlocking during a fire emergency. The outside trim cylinder retracts the latch bolt for mechanical override of night latch function. Only available with TP, K or L functions. The E7500 lock contains a SPDT signal to monitor the outside trim condition (locked or unlocked) and a second SPDT signal switch to monitor the latch bolt. Features and benefits E996L §Fail safe or fail secure, can also be converted in the field §Conversion kits available to add to existing 996L trim §Available with blank escutcheon function or cylinder operation for night latch function E7500 §Field reversible handing §24 VDC continuous-duty solenoid §Fail safe or fail secure optional1 1 Some fire codes will require fail safe (FS) operation for stairwell doors. Be sure to specify the correct operation for your application. E996L, E7500 Electrified trim, electric mortise lock Allegion, the Allegion logo, Von Duprin and the Von Duprin logo are trademarks of Allegion plc, its subsidiaries and/or affiliates in the United States and other countries. All other trademarks are the property of their respective owners. E996L specifications Solenoid 24VDC Solenoid draw 0.22 AMPS E7500 specifications Solenoid .60 Amps @ 12VDC .30 Amps @ 24VDC Each switch Up to 2.0 Amps @ 24CDC Maximum The E option does not include the power transfer from door to frame, the power supply or the control operator. (Refer to EPT-10 and PS902 or PS914 power supply) Power wire runs through exit device body E996L trim Power transfer (EPT2 shown) Power Supply PS902 24 VDC output Control switch (normally closed) E996L Electrical wiring §Power input for E996L is 24 VDC §Two wires on the trim are non-polarized (18 AWG minimum) Standard features: §Field reversible handing §24 VDC continuous duty solenoid Optional features: §Fail safe (locked when energized, unlocked when de- energized or during power failure). Specify with suffix “FS.” §Fail secure (unlocked when energized, locked when de-energized or during power failure). Specify with suffix “FSE.” §24 VAC (with SO option) §12 VDC §12 VAC (with SO option) Note: Some fire codes will require “Fail Safe” (FS) operation for stairwell doors. Be sure to specify the correct operation for your application. To order, specify Note: To order, please reference Von Duprin catalog and price book §Use “E” prefix, example E996L § When ordering with device specify trim series with “E” prefix, example 9927L-BE 3’ US26D E996L. §Device type, R/V (rim/surface or concealed vertical rod) or M (mortise) §Fail Safe (FS) or Fail Secure (FSE) §RHR is furnished standard if not specified. Field reversible. §Lever style (06 lever is furnished standard) §Finish: US3, US4, US10, US10B, SP313, US26, US26D, SPBLK, US15 To order, specify Note: To order, please reference Von Duprin catalog and price book §Use prefix “E,” example E9975 §FS or FSE §Voltage and current Allegion (NYSE: ALLE) is a global pioneer in safety and security, with leading brands like CISA®, Interflex®, LCN®, Schlage®, SimonsVoss® and Von Duprin®. Focusing on security around the door and adjacent areas, Allegion produces a range of solutions for homes, businesses, schools and other institutions. Allegion is a $2 billion company, with products sold in almost 130 countries. For more, visit www.allegion.com. About Allegion © 2019 Allegion 010103, Rev. 12/19 www.allegion.com/us PHYSICAL ACCESS CONTROL HID Mobile Access®iCLASS SE® & multiCLASS SE® Mobile Enabled Readers hidglobal.com MOBILE ENABLED ICLASS SE PLATFORM READERS THAT OFFER NEW WAYS TO OPEN DOORS Innovative – Enables secure access with a mobile device by leveraging standard communications technologies that work with both iOS® and Android™ operating systems. Convenient – Enhances the transactional experience by opening doors with a tap or “Twist and Go” gesture, merging security with convenience. Dynamic – Supports new Mobile IDs and existing card populations for seamless migration to a more secure standard. A UNIQUE USER EXPERIENCE HID Mobile Access® offers a patented gesture technology that allows door and gate access with a twist of the handset upon approaching an iCLASS SE® or multiCLASS SE® mobile-enabled reader. iCLASS SE® and multiCLASS SE® mobile-enabled readers are part of the HID Mobile Access® solution that offers a consistent user experience across different devices and operating systems, including iOS and Android. The readers can be configured to using a smartphone with a “tap” or utilizing HID Global’s patented “Twist and Go” gesture technology. Ideal for new and existing installations, the interoperable iCLASS SE and multiCLASS SE readers support a variety of industry-standard technologies, including iCLASS Seos®, standard iCLASS®, iCLASS SE, MIFARE®, MIFARE DESFire® and HID Prox. Simultaneous support of mobile device and existing card populations facilitates mixed population use and migration to a more secure standard. Advanced multi-layered security is provided via the iCLASS SE platform with its Secure Identity Object® (SIO®) data model. This additional layer of security ensures tamper-resistant protection of keys and cryptographic operations. The incorporation of Seos technology to manage identity data results in a dynamic and highly secure mobile solution. iCLASS SE® AND multiCLASS® SE MOBILE-ENABLED READERS FEATURES: Adjustable read settings control overall power and read range of Mobile IDs, enabling flexibility for both close-proximity “tap” and long-range “Twist and Go” distances. Read settings administered using mobile phone during installation. Directional antenna enables long- range reading distances of up to 6.6’ in correct orientation – in front of the reader and not behind it. SPECIFICATIONS An ASSA ABLOY Group brand © 2017 HID Global Corporation/ASSA ABLOY AB. All rights reserved. HID, HID Global, the HID Blue Brick logo, the Chain Design, HID Mobile Access, iCLASS SE, multiCLASS SE, MIFARE, DESfire, Seos, Prox, and Secure Identity Services are trademarks or registered trademarks of HID Global in the U.S. and/or other countries. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owners. 2016-03-21-hid-mobile-access-readers-nfc-ds-en PLT-02094 North America: +1 512 776 9000 Toll Free: 1 800 237 7769 Europe, Middle East, Africa: +44 1440 714 850 Asia Pacific: +852 3160 9800 Latin America: +52 55 5081 1670 hidglobal.com Model Name R10 RP10 R15 RP15 R40 RP40 RK40 RPK40 Typical Read Range* Both "Twist & Go" and "Tap" ranges are likely maximum distances based on recommended settings in a typical lab environment. Read ranges and behavior will vary by installation, due to a variety of factors. Reader-specific read range and power settings will contribute to adjusting behavior. Mobile IDs using Bluetooth & Seos® Twist and Go 6.6 ft (2 m)6.6 ft (2 m)6.6 ft (2 m)6.6 ft (2 m) Tap 5.9" (15 cm)5.9" (15 cm)5.9" (15 cm)5.9" (15 cm) Mounting Mini-Mullion Size; mount on door mullion or any flat surface Mullion Size; mount on door mullion or any flat surface Wall Switch Size; designed to mount to and cover single-gang switch boxes primarily used in the Americas and includes a slotted mounting plate for European and Asian back box spacing Wall Switch Size; designed to mount to and cover single- gang switch boxes primarily used in the Americas and includes a slotted mounting plate for European and Asian back box spacing Color Black or Gray Keypad No No No Yes (4x3) Dimensions 1.9” x 4.1” x 0.9” 4.8 cm x 10.3 cm x 2.3 cm 1.9” x 6.0” x 0.9” 4.8 cm x 15.3 cm x 2.3 cm 3.3” x 4.8” x 1.0” 8.4 cm x 12.2 cm x 2.4 cm 3.3” x 4.8” x 1.1” 8.5 cm x 12.2 cm x 2.8 cm Operating Voltage Range 5-16 VDC; Linear supply recommended Standby AVG Current 82 mA 97 mA 82 mA 97 mA 87 mA 107 mA 107 mA 117 mA PEAK Current 240 mA 240 mA 240 mA 240 mA 240 mA 240 mA 260 mA 260 mA Operating Temperature -13º to 150º F (-25º to 65º C) Storage Temperature -67º to 185º F (-55º to 85º C) Operating Humidity 5% to 95% relative humidity non-condensing Transmit Frequency 2.4GHZ, 13.56 MHz 2.4 GHz Credential Compatibility*Secure Identity Object (SIO) on Mobile IDs (Bluetooth Smart) 13.56 MHz Credential Compatibility Secure Identity Object (SIO) on iCLASS Seos, iCLASS SE, SIO-enabled MIFARE DESFire EV1 and SIO-enabled MIFARE Classicstandard iCLASS Access Control Application (standard iCLASS cards) ISO14443A (MIFARE) CSN, ISO14443B CSN, ISO15693 CSN Custom sectors on MIFARE, Custom app/file on DESFire EV1 (custom programming feature) Secure Identity Object (SIO) on NFC-enabled devices using Host-Based Card Emulation 125 kHz Credential Compatibility (multiCLASS only) HID Prox, AWID, EM4102 Cable Distance Optional OSDP with SCP over RS485 (4000 ft) Wiegand/Clock-and-Data Interface 500ft (150m) (22AWG) Use Shielded cable for best results Reader Personalization Mobile-enabled readers come fully personalized to read customer/site-specific Mobile IDs. Mobile-ready readers come fully prepared to read Mobile IDs but to do not include customer/site-specific personalization. Install Mobile-ready readers to prepare for Mobile IDs in the future. Panel Connection Pigtail or Terminal Strip Certifications Bluetooth SIG certification, UL-294/cUL (US & Canada), FCC certification (US), IC (Industry Canada), CE now including RoHS II, REACH Crypto Processor Hardware Common Criteria Rating EAL5+ Patents US7124943, US6058481, US6337619 Housing Material UL94 Polycarbonate Manufactured with % of recycled content (Pigtail) 10.5%11.0%10.5%10.9% Manufactured with % of recycled content (Terminal Strip) 10.5%11.0%11.0%12.3% UL Ref Number R10E RP10E R15E RP15E R40E RP40E RK40E RPK40E Warranty Limited Lifetime GEORGE RISK INDUSTRIES, INC. G.R.I. PLAZA KIMBALL, NE 69145 MADE IN U.S.A. TOLL-FREE 1-800-445-5218 TOLL-FREE 1-800-523-1227 (308) 235-4645 FAX (308) 235-3561 E-MAIL: grisales@megavision.com WEB SITE: www.grisk.com INDUSTRIAL TRACK MOUNT SWITCH SET 4700-A SERIES PART NUMBERS: Track Size Closed Loop SPDT 1.75” to 2.75” 4700-A 4701-A 2.5” to 4”4700-AXL 4701-AXL Gap Up To 3” Reversible Probe Assembly Left or Right Installation Reversible Cable Exit 3 ft. Armored Cable Standard Multi Position Adjustable Magnet Bracket Closed Loop or SPDT Hinge Design for Tighter Clamping to Track Up to 3” Gap Fits Channels from 1.75” up to 4”. Self Drilling Screws Included For Easy Installation Contacts are on the Channel and not where they can get damaged on the floor No Special Tools Required for Installation 4700-A DESCRIPTION: The G.R.I. 4700-A Series Industrial Track Mount Switches are designed to eliminate false alarms from standard floor switches getting damaged by fork lifts and other equipment. The contacts are moved up onto the track and out of the way of equipment. The 4700-A Series switches are designed to be easy to install and very adjustable. They can attach to a wide range of track sizes and only require tightening one or two screws to install the contacts. It can be installed on either side of the door and the cable exit can be reversed to simplify installation. An adjustable magnet bracket extends the reach on particularly difficult installations and self drilling screws shorten installations times. Also with a gap of up to 3 inches, doors that wear and get misaligned are not a problem. GEORGE RISK INDUSTRIES, INC. G.R.I. PLAZA KIMBALL, NE 69145 TOLL-FREE 1-800-445-5218 TOLL-FREE 1-800-523-1227 (308) 235-4645 FAX (308) 235-3561 E-MAIL: grisales@megavision.com WEB SITE: www.grisk.comBA-239 Rev C 8/31/2010 CONTACT YOUR G.R.I. DISTRIBUTOR OR CALL: INSTALLATION INSTRUCTIONS: Select a location on the channel that will be out of the way during normal use of the door. The switch can be located anywhere along the channel. This location should also have a matching location on the door when it is in the closed position that the magnet can be attached to. If necessary reverse the armored cable by removing the screw opposite the cable and moving the probe to the opposite side of the switch. Then just reinstall the screw. Before assembling the switch, back out the hex head screw until the end is flush with the switch body. Assemble the switch by sliding the hinge plate into the slot on the switch and inserting the L shaped bracket into the other slot on the switch. (XL version: Install the countersink screw and nut through switch body and L shaped bracket. Snug nut up letting L shaped bracket still slide.) Then squeeze the switch assembly around the channel making sure the switch locks into a slot on the L shaped bracket. (XL version: Tighten the nut making sure that the switch stays in the slot on the L shaped bracket.) Then just tighten the hex head screw to firmly attach switch to channel. The magnet is installed by locating a position on the door that will be out of the way as the door is opened and closed. The magnet should be placed vertically and so that it will stay in range of the switch as the door wears or moves around. There are multiple mounting positions on the magnet bracket in order to make finding the mounting position easier. MADE IN U.S.A. INDUSTRIAL TRACK MOUNT SWITCH SET 4700-A CLOSED N/O A 0.150 10 160 0.400 4701-A OPEN/CLOSED SPDT C 0.140 5 175VDC 0.250 4700-AXL CLOSED N/O A 0.150 10 160 0.400 4701-AXL OPEN/CLOSED SPDT C 0.140 5 175VDC 0.250 PART LOOP ELECTRICAL REED MAXIMUM MAXIMUM MAXIMUM MAXIMUM NUMBER TYPE CONFIG. FORM INITIAL CONTACT CONTACT SWITCHING SWITCHING RESISTANCE RATING VOLTAGE CURRENT (Ω) (W) (VDC) (A) GRI products meet or exceed these minimum general specifications: MAGNET SWITCH Extends up to 4”1.71 3.12 2.13 4700-A 4700-AXL Home Products About GRI Contact GRI Where to Buy Testimonials What's New!4400 Series Industrial Surface Mount Switch Sets4400-A Lifetime WarrantyUL and ULC approvedArmored or jacketed cableStandard gap up to 2 1/2"+DPDT gap up to 2 1/2"3' standard lead lengthWeather resistant aluminum housingIdeal for securing chain link fenceLonger leads or jacketed cable on requestVariety of optional mounting brackets availableSwitches or magnets are available separatelySupervisory loops availableGRI's 4400 Switch Series is a heavy duty surface mounted industrial grade contact. A weather resistant rugged aluminum housing and a variety of optional mounting brackets make it ideal for securing chain link gates, overhead garage doors, safes or walk-in freezer doors. Kits include hardware, brackets and mounting instructions. 4400A Product Specification PDF's About PDF 4400 Series Industrial Surface Mount Switch Set Product Specification PDF 4400 Series Mounting Kits PDF [Home] [Products] [What's New!] [Security Products] [Data Entry Peripherals] [Pushbutton Switches] [Custom Engraved Keycaps] [Proximity Sensors] [Contact GRI] [About GRI] Can't find what you are looking for? Revised: Friday, September 13, 2013 GEORGE RISK INDUSTRIES, INC. G.R.I. PLAZA KIMBALL, NE 69145 MADE IN U.S.A. TOLL-FREE 1-800-445-5218 TOLL-FREE 1-800-523-1227 (308) 235-4645 FAX (308) 235-3561 E-MAIL: grisales@megavision.com WEB SITE: www.grisk.com ALUMINUM INDUSTRIAL WIDE GAP SWITCH SET 4400 SERIES PART NUMBERS: Closed Loop SPDT DPDT Standard Gap 4400 4402 2 1/2”+4400-A 4402-A 4405-A Ideal For Securing Chain Link Gates, Overhead Garage Doors, Safes & Walk-In Freezer Doors (Note: Can operate within range of 257ºF to -40ºF) Spacer is PN 5226 Weather Resistant Rugged Aluminum Housing 36” 2 Conductor Vinyl Jacketed Cable 4400 36” Armored Cable 4400-A Mounting Hardware Included A Variety of Optional Mounting Brackets Available Built-in E.O.L. Resistors and Diodes Upon Request Supervisory Loops Available Upon Request Switches and Magnets Available Separately Lifetime Warranty U LISTEDLISTED L ULC® 4400-A 8450-3 Gate Mounting Kit Includes 4402-A Switch Set, Brackets and Hardware Other Mounting Kits Available. Call Factory for Information. GEORGE RISK INDUSTRIES, INC. G.R.I. PLAZA KIMBALL, NE 69145 TOLL-FREE 1-800-445-5218 TOLL-FREE 1-800-523-1227 (308) 235-4645 FAX (308) 235-3561 E-MAIL: grisales@megavision.com WEB SITE: www.grisk.comBA-99 Rev. M 10/19/2012 CONTACT YOUR G.R.I. DISTRIBUTOR OR CALL: INSTALLATION APPLICATIONS: G.R.I.’s 4400 switch series is a heavy duty surface mounted industrial grade contact. A weather resistant rugged aluminum housing and a variety of optional mounting brackets make it ideal for securing chain link gates, overhead garage doors, safes or walk-in freezer doors. A standard 3 foot length of stainless steel cable is offered as is a vinyl jacketed CL-2 type cable. Custom cable lengths of either type are available by special request. A case spacer PN #5226 can also be ordered as a separate mounting accessory. Switch sets include all other mounting hardware. A mounting kit PN #8297 is also available for garage door track mounting. The kit includes a 4402-A switch set, brackets and mounting hardware. MADE IN U.S.A. WARRANTY: Lifetime warranty against workmanship, material and factory defects. ALUMINUM INDUSTRIAL WIDE GAP SWITCH SET 4400 Closed N/O A .150 10 200 .500 4400-A Closed N/O A .150 10 200 .500 4402 Open/Closed SPDT C .140 5 175VDC .250 4402-A Open/Closed SPDT C .140 5 175VDC .250 4405-A Open/Closed DPDT CX2 .140 5 175VDC .250 PART LOOP ELECTRICAL REED MAXIMUM MAXIMUM MAXIMUM MAXIMUM NUMBER TYPE CONFIG.FORM INITIAL CONTACT CONTACT SWITCHING SWITCHING RESISTANCE RATING VOLTAGE CURRENT (Ω ) (W) (VDC) (A) GRI products meet or exceed these minimum general specifications: 4400-A 2.600 .875 .300 2.300 .219 .875.656 .300 2.300 2.600 (2)Ø.150 THRU ∨Ø.279 X 100º BOTH SIDES (2)Ø.150 THRU ∨Ø.279 X 100º BOTH SIDES .600 .600 SWITCH SIDE MAGNET SIDE GEORGE RISK INDUSTRIES, INC. G.R.I. PLAZA KIMBALL, NE 69145 MADE IN U.S.A. MOUNTING KITS Part Number 8450-1 Gate Mounting Kit Consists of: 1 S4402-A SPDT Switch 1 M-4400 Magnet 2 S-201 Brackets 4 #6-32 x 5/16 Zinc Hex Nuts 4 #6 External Lock Washers 4 #6-32 x 3/4 Phillips Machine Screws 2 #8 x 1 Self Tap Combo Panhead Type A Screws Part Number 8450-2 Gate Mounting Kit Consists of: 1 S4402-A SPDT Switch 1 M-4400 Magnet 2 S-202 Brackets 4 #6-32 x 5/16 Zinc Hex Nuts 4 #6 External Lock Washers 4 #6-32 x 3/4 Phillips Machine Screws 2 #8 x 1 Self Tap Combo Panhead Type A Screws Part Number 8450-3 Gate Mounting Kit Consists of: 1 S4402-A SPDT Switch 1 M-4400 Magnet 1 S-202 Bracket 1 S-201 Bracket 4 #6-32 x 5/16 Zinc Hex Nuts 4 #6 External Lock Washers 4 #6-32 x 3/4 Phillips Machine Screws 2 #8 x 1 Self Tap Combo Panhead Type A Screws TOLL-FREE 1-800-445-5218 TOLL-FREE 1-800-523-1227 (308) 235-4645 FAX (308) 235-3561 E-MAIL: grisales@megavision.com WEB SITE: www.grisk.com AXIS P3375-V Network Camera Classic HDTV 1080p fixed dome AXIS P3375-V Network Camera is an indoor fixed dome that provides HDTV 1080p video.Equipped with WDR –Forensic Capture to handle scenes with strong variations in light,and Lightfinder technology for exceptional light sensitivity, this camera delivers outstanding video quality in any light conditions.It supports Axis Zipstream technology which significantly reduces bandwidth and storage requirements.AXIS P3375-V is a discreet,IK10-rated vandal-resistant camera equipped with I/O ports and support for two-way audio.It comes with a varifocal lens and remote zoom and focus,which facilitates installation and fine tuning. >HDTV 1080p video quality >Zipstream technology >WDR –Forensic Capture >Lightfinder technology >Two-way audio and I/O ports Datasheet AXIS P3375-V Network Camera Camera Image sensor Progressive scan RGB CMOS 1/3” Lens Varifocal,3–10 mm,F1.4 Horizontal field of view:90°–34° Vertical field of view:50°–20° Remote focus and zoom,P-Iris control,IR corrected Day and night Automatically removable infrared-cut filter Minimum illumination HDTV 1080p 25/30 fps with WDR -forensic capture and Lightfinder: Color:0.15 lux,F1.4 B/W:0.03 lux,F1.4 HDTV 1080p 50/60 fps: Color:0.30 lux,F1.4 B/W:0.06 lux,F1.4 Shutter time 1/66500 s to 1 s Camera angle adjustment Pan ±180°,tilt -20°to +80°,rotation ±90° Video Video compression H.264 Baseline,Main and High Profiles (MPEG-4 Part 10/AVC) Motion JPEG Resolution 1920x1080 to 160x90 Frame rate With WDR:25/30 fps with power line frequency 50/60 Hz Without WDR:50/60 fps with power line frequency 50/60 Hz Video streaming Multiple,individually configurable streams in H.264 and Motion JPEG Axis Zipstream technology in H.264 Controllable frame rate and bandwidth VBR/ABR/MBR H.264 Multi-view streaming 2 individually cropped out view areas Pan/Tilt/Zoom Digital PTZ,preset positions Image settings Compression,color,brightness,sharpness,contrast,local contrast,white balance,Exposure control (including automatic gain control),exposure zones,fine tuning of behavior at different light levels,WDR -forensic capture:Up to 120 dB depending on scene,text and image overlay,mirroring of images,privacy masks Rotation:0°,90°,180°,270°,including Corridor Format Audio Audio streaming Two-way Audio compression AAC LC 8/16/32/44.1/48 kHz,G.711 PCM 8 kHz, G.726 ADPCM 8 kHz,Opus 8/16/48 kHz,LPCM 48 kHz Configurable bit rate Audio input/output External microphone input or line input,line output,built-in microphone (can be disabled) Network Security Password protection,IP address filtering,HTTPSa encryption, IEEE 802.1X (EAP-TLS)a network access control,digest authentication,user access log,centralized certificate management,brute force delay protection,signed firmware Supported protocols IPv4,IPv6 USGv6,HTTP,HTTPSa,SSL/TLSa,QoS Layer 3 DiffServ, FTP,SFTP,CIFS/SMB,SMTP,Bonjour,UPnP®,SNMP v1/v2c/v3 (MIB-II),DNS,DynDNS,NTP,RTSP,RTP,SRTP,TCP,UDP,IGMP, RTCP,ICMP,DHCP,ARP,SOCKS,SSH,LLDP,MQTT System integration Application Programming Interface Open API for software integration,including VAPIX®and AXIS Camera Application Platform;specifications at axis.com AXIS Video Hosting System (AVHS)with One-Click Connection ONVIF®Profile G,ONVIF®Profile S,and ONVIF®Profile T, specification at onvif.org Analytics Included AXIS Video Motion Detection,active tampering alarm,audio detection Supported AXIS Digital Autotracking,AXIS Motion Guard,AXIS Fence Guard, AXIS Cross Line Detection Support for AXIS Camera Application Platform enabling installation of third-party applications,see axis.com/acap Event triggers Analytics,supervised external input,virtual inputs through API, edge storage events Event actions Record video:SD card and network share Upload of images or video clips:FTP,SFTP,HTTP,HTTPS,network share and email Pre-and post-alarm video or image buffering for recording or upload Notification:email,HTTP,HTTPS,TCP and SNMP trap Overlay text,external output activation,play audio clip Data streaming Event data Built-in installation aids Remote zoom,remote focus,pixel counter General Casing IK10 impact-resistant casing with polycarbonate hard-coated dome and aluminum base Encapsulated electronics,Captive screws Color:White NCS S 1002-B For repainting instructions and impact on warranty,contact your Axis partner. Sustainability PVC free Mounting ¼”-20 UNC tripod screw thread Memory 512 MB RAM,256 MB Flash Power Power over Ethernet IEEE 802.3af/802.3at Type 1 Class 2 Typical:2.8 W,Max 3.9 W Connectors RJ45 10BASE-T/100BASE-TX PoE Terminal block for 1 supervised alarm input and 1 digital output (12 V DC output,max load 50 mA) 3.5 mm mic/line in,3.5 mm line out Storage Support for microSD/microSDHC/microSDXC card Support for SD card encryption Support for recording to network-attached storage (NAS) For SD card and NAS recommendations see axis.com Operating conditions 0 °C to 50 °C (32 °F to 122 °F) Humidity 10–85%RH (non-condensing) Storage conditions -40 °C to 65 °C (-40 °F to 149 °F) Humidity 5-95%RH (non-condensing) Approvals EMC EN 55032 Class A,EN 61000-6-1,EN 61000-6-2,EN 55024, FCC Part 15 Subpart B Class A,ICES-003 Class A,VCCI Class A, RCM AS/NZS CISPR 32 Class A,KCC KN32 Class A,KN35 Safety IEC/EN/UL 62368-1,IS 13252 Environment IEC 60068-2-1,IEC 60068-2-2,IEC 60068-2-14, IEC 60068-2-27,IEC 60068-2-6,IEC 60068-2-78,EN 50581, IEC 62262 IK10 Network NIST SP500-267 Weight 0.7 kg (1.5 lb) Dimensions Ø 148 x 99 mm (Ø 5 13/16 x 3 7/8 in) Included accessories Installation guide,Windows decoder 1-user license,drill hole template,Resistorx®T20 L-key,I/O connector Optional accessories AXIS T94K02L Recessed Mount Kit AXIS P33 Pendant Kit AXIS T94H01P Conduit Back Box Indoor Axis P33 Mounting Bracket Axis Mounts AXIS T83 Microphones Black casing Smoked dome For more accessories,see axis.com Video management software AXIS Companion,AXIS Camera Station,video management software from Axis’Application Development Partners available on axis.com/vms Languages English,German,French,Spanish,Italian,Russian,Simplified Chinese,Japanese,Korean,Portuguese,Traditional Chinese Warranty Axis 3-year warranty and AXIS Extended Warranty option,see axis.com/warranty a.This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.(openssl.org),and cryptographic software written by Eric Young (eay@cryptsoft.com). Environmental responsibility: axis.com/environmental-responsibility www.axis.com ©2017 -2020 Axis Communications AB.AXIS COMMUNICATIONS,AXIS,and VAPIX are registered trademarks or trademark applications of Axis AB in various jurisdictions.All other company names and products are trademarks or registered trademarks of their respective companies.We reserve the right to introduce modifications without notice. T10109797/EN/M13.2/2006 AXIS P3375-VE Network Camera Classic,outdoor-r eady HDTV 1080p fixed dome AXIS P3375-VE Network Camera is an outdoor-ready fixed dome that provides HDTV 1080p video.Equipped with WDR –Forensic Capture to handle scenes with strong variations in light,and Lightfinder technology for exceptional light sensitivity,this camera delivers outstanding video quality in any light conditions.It supports Axis Zipstream technology which significantly reduces bandwidth and storage requirements.AXIS P3375-VE is a discreet,IK10-rated vandal-re- sistant camera equipped with I/O ports and support for two-way audio.It comes with a varifocal lens and remote zoom and focus,which facilitates installation and fine tuning. >HDTV 1080p video quality >Zipstream technology >WDR –Forensic Capture >Lightfinder technology >Two-way audio and I/O ports Datasheet AXIS P3375-VE Network Camera Camera Image sensor Progressive scan RGB CMOS 1/3” Lens Varifocal,3–10 mm,F1.4 Horizontal field of view:90°–34° Vertical field of view:50°–20° Remote focus and zoom,P-Iris control,IR corrected Day and night Automatically removable infrared-cut filter Minimum illumination HDTV 1080p 25/30 fps with WDR -forensic capture and Lightfinder: Color:0.15 lux,F1.4 B/W:0.03 lux,F1.4 HDTV 1080p 50/60 fps: Color:0.30 lux,F1.4 B/W:0.06 lux,F1.4 Shutter time 1/66500 s to 1 s Camera angle adjustment Pan ±180°,tilt -20°to +80°,rotation ±90° Video Video compression H.264 Baseline,Main and High Profiles (MPEG-4 Part 10/AVC) Motion JPEG Resolution 1920x1080 to 160x90 Frame rate With WDR:25/30 fps with power line frequency 50/60 Hz Without WDR:50/60 fps with power line frequency 50/60 Hz Video streaming Multiple,individually configurable streams in H.264 and Motion JPEG Axis Zipstream technology in H.264 Controllable frame rate and bandwidth VBR/ABR/MBR H.264 Multi-view streaming 2 individually cropped out view areas Pan/Tilt/Zoom Digital PTZ,preset positions Image settings Compression,color,brightness,sharpness,contrast,local contrast,white balance,Exposure control (including automatic gain control),exposure zones,fine tuning of behavior at different light levels,WDR -forensic capture:Up to 120 dB depending on scene,text and image overlay,mirroring of images,privacy masks Rotation:0°,90°,180°,270°,including Corridor Format Audio Audio streaming Two-way Audio compression AAC LC 8/16/32/44.1/48 kHz,G.711 PCM 8 kHz, G.726 ADPCM 8 kHz,Opus 8/16/48 kHz,LPCM 48 kHz Configurable bit rate Audio input/output External microphone input or line input,line output Network Security Password protection,IP address filtering,HTTPSa encryption, IEEE 802.1X (EAP-TLS)a network access control,digest authentication,user access log,centralized certificate management,brute force delay protection,signed firmware Supported protocols IPv4,IPv6 USGv6,HTTP,HTTPSa,SSL/TLSa,QoS Layer 3 DiffServ, FTP,SFTP,CIFS/SMB,SMTP,Bonjour,UPnP®,SNMP v1/v2c/v3 (MIB-II),DNS,DynDNS,NTP,RTSP,RTP,SRTP,TCP,UDP,IGMP, RTCP,ICMP,DHCP,ARP,SOCKS,SSH,LLDP,MQTT System integration Application Programming Interface Open API for software integration,including VAPIX®and AXIS Camera Application Platform;specifications at axis.com AXIS Video Hosting System (AVHS)with One-Click Connection ONVIF®Profile G,ONVIF®Profile S,and ONVIF®Profile T, specification at onvif.org Analytics Included AXIS Video Motion Detection,active tampering alarm,audio detection Supported AXIS Digital Autotracking,AXIS Perimeter Defender, AXIS Motion Guard,AXIS Fence Guard,AXIS Cross Line Detection Support for AXIS Camera Application Platform enabling installation of third-party applications,see axis.com/acap Event triggers Analytics,supervised external input,virtual inputs through API, edge storage events Event actions Record video:SD card and network share Upload of images or video clips:FTP,SFTP,HTTP,HTTPS,network share and email Pre-and post-alarm video or image buffering for recording or upload Notification:email,HTTP,HTTPS,TCP and SNMP trap Overlay text,external output activation,play audio clip Data streaming Event data Built-in installation aids Remote zoom,remote focus,pixel counter General Casing IP66-and NEMA 4X-rated,IK10 impact-resistant casing with polycarbonate hard-coated dome,aluminum base,and dehumidifying membrane Encapsulated electronics,Captive screws Color:White NCS S 1002-B For repainting instructions and impact on warranty,contact your Axis partner. Sustainability PVC free Mounting Mounting bracket with junction box holes (double-gang, single-gang,4”octagon and 4”square) ¼”-20 UNC tripod screw thread Memory 512 MB RAM,256 MB Flash Power Power over Ethernet IEEE 802.3af/802.3at Type 1 Class 3 Typical:3.1 W,Max 5.6 W Connectors RJ45 10BASE-T/100BASE-TX PoE Terminal block for 1 supervised alarm input and 1 digital output (12 V DC output,max load 50 mA) 3.5 mm mic/line in,3.5 mm line out Storage Support for microSD/microSDHC/microSDXC card Support for SD card encryption Support for recording to network-attached storage (NAS) For SD card and NAS recommendations see axis.com Operating conditions -40 °C to 55 °C (-40 °F to 131 °F) Start-up:-40 °C to 55 °C (-40 °F to 131 °F) Humidity 10–100%RH (condensing) Storage conditions -40 °C to 65 °C (-40 °F to 149 °F) Humidity 5-95%RH (non-condensing) Approvals EMC EN 55032 Class A,EN 50121-4,IEC 62236-4,EN 61000-6-1, EN 61000-6-2,EN 55024,FCC Part 15 Subpart B Class A, ICES-003 Class A,VCCI Class A,RCM AS/NZS CISPR 32 Class A, KCC KN32 Class A,KN35 Safety IEC/EN/UL 62368-1,IEC/EN/UL 60950-22,IS 13252 Environment IEC 60068-2-1,IEC 60068-2-2,IEC 60068-2-14, IEC 60068-2-27,IEC 60068-2-6,IEC 60068-2-78,EN 50581, IEC 62262 IK10,IEC/EN 60529 IP66,NEMA 250 Type 4X Network NIST SP500-267 Weight 1.5 kg (3.3 lb)with weathershield Dimensions Ø 178 x 112 mm (Ø 7 x 4 7/16 in) Weathershield:226 x 163 mm (8 7/8 x 6 7/16 in) Included accessories Installation guide,Windows decoder 1-user license,drill hole template,Resistorx®T20 L-key,mounting bracket,weathershield, cable gaskets,connector guard,I/O connector Optional accessories AXIS P33-VE Pendant Kit including weathershield AXIS T94M02L Recessed Mount AXIS P33-VE Cable Cover AXIS P33-VE 3/4"NPS Adapter AXIS Dome Intrusion Switch B I/O Audio Cable,5 m (16 ft) Axis mounts and cabinets AXIS T8351 Microphone For more accessories,see axis.com Video management software AXIS Companion,AXIS Camera Station,video management software from Axis’Application Development Partners available on axis.com/vms Languages English,German,French,Spanish,Italian,Russian,Simplified Chinese,Japanese,Korean,Portuguese,Traditional Chinese Warranty Axis 3-year warranty and AXIS Extended Warranty option,see axis.com/warranty a.This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.(openssl.org),and cryptographic software written by Eric Young (eay@cryptsoft.com). Environmental responsibility: axis.com/environmental-responsibility www.axis.com ©2017 -2020 Axis Communications AB.AXIS COMMUNICATIONS,AXIS,and VAPIX are registered trademarks or trademark applications of Axis AB in various jurisdictions.All other company names and products are trademarks or registered trademarks of their respective companies.We reserve the right to introduce modifications without notice. T10109795/EN/M12.2/2005 Intrusion Alarm Systems | Blue Line Gen2 TriTech Motion Detectors Blue Line Gen2 TriTech Motion Detectors www.boschsecurity.com u Pet‑friendly Selectable model available – optimize installation for pet (45 kg [100 lb]) and non‑pet applications u Dynamic Temperature Compensation – superior catch performance in any environment u Microwave Noise Adaptive processing – reduce false alarms from repetitive sources u Wall to Wall Coverage – superior catch performance u Flexible Mounting Height, No Adjustments – reduce installation time and false alarms, improve catch performance The Blue Line Gen2 TriTech Motion Detectors (ISC- BDL2) use a combination of passive infrared (PIR) and microwave Doppler radar detection with advanced signal processing. The pet‑friendly (‑WP) models generate alarms for human intruders without generating false alarms for pets. These small unobtrusive detectors are simple to install and do not need field adjustments. Functions First Step Processing (FSP) First Step Processing (FSP) almost instantly responds to human targets without producing false alarms from other sources. FSP adjusts the detector's sensitivity based on signal amplitude, polarity, slope, and timing. This eliminates the need for the installer to select the sensitivity level, thus improving ease of installation and reliability. Pet‑friendly Selectivity (‑WP models only) The installer can turn pet immunity on or off based upon application requirements. When pet immunity is turned off, the detector provides superior catch performance identical to the non‑pet models. When pet immunity is turned on, the detector can distinguish between signals caused by humans and signals caused by pets. It ignores signals caused by one or two pets up to 45 kg (100 lb) or numerous rodents. Microwave Noise Adaptive Processing Microwave Noise Adaptive Processing adjusts to background disturbances, reducing false alarms without sacrificing intruder detection. Dynamic Temperature Compensation The detector intelligently adjusts its sensitivity so that it can identify human intruders at virtually any temperature. Wall-to-Wall Coverage An improved lookdown zone and coverage range of 12 m x 12 m (40 ft x 40 ft) provide wall-to-wall coverage. Self-locking Enclosure The sliding self‑locking enclosure has an integrated bubble level and custom gap‑free, lift‑gate style terminal blocks to make installation easier. Sealed Optics and Electronics The optics and electronics are assembled into the front enclosure and sealed with a protective cover to prevent damage during installation. The sealed optical chamber also prevents drafts and insects from affecting the detector. Test Features Externally visible alarm LED can be disabled after installation. RFI and Impact Immunity E-models feature improved immunity to false alarms from external sources including radio frequency interference, “popcorn noise”, as well as physical impact. Through use of a high performance pyro (infrared) sensor with integrated signal filtering, the highest quality electrical components and design that produces the best-in-class signal to noise ratio, and sophisticated signal processing, these detectors are more robust than ever against false alarms. Improved Resistance to Sabotage E-model detectors are now tested and approved to the EN50131-5-3 requirements for immunity to interference from external radio frequency sources. Detection performance and false alarm immunity are ensured when in the presence of such sources that could degrade the performance of detectors that are not approved to this standard. Certifications and approvals These detectors are also designed to comply with the following: Europe Complies with Directive 2002/95/EC - Restriction of the use of certain Hazardous Substances (RoHS) China Complies with CCC GB10408.1 and GB10408.9 Region Regulatory compliance/quality marks Europe CE 2014/53/EU (RED) 2011/65/EU(RoHS) (EU 2015/863 amending AnnexII to Directive 2011/65/EU [Notifiedbody 0700]) | [ISC-BDL2-W12GE, ISC-BDL2-WP12GE, ISC-BDL2-W12HE, ISC-BDL2-WP12HE] EN50131 EN50131-2-4 Grade 2 EnvironmentalClass II (G models) I (H models) Sweden SBSC 20-43 Intyg_20-43_ISC-BDL2-W12GE_EN SBSC 20-44 SBSC_ISC-BDL2-WP12GE USA UL [ISC-BDL2-W12G, ISC-BDL2-WP12G,ISC-BDL2-WP6G] UL 20190115; UL639 – Standard for Intru-sion-Detection Units FCC [ISC-BDL2-W12G, ISC-BDL2-WP12G,ISC-BDL2-WP6G] Canada ULC CAN/ULC S306-03 - Canadian Standardfor Intrusion Detection Units Region Regulatory compliance/quality marks IC [ISC-BDL2--W12G, ISC-BDL2-WP12G,ISC-BDL2-WP6G] France AFNOR EN50131-2-4 Grade 2, NF324-H58 +RTC 50131-2-4 ISC-BDL2-W12HE - Cer-tificate # 2820200003A1 ISC-BDL2-WP12HE - Certificate #2820200003B1 China CCC 2010031901000323 [ISC-BDL2-WP6G-CHI, ISC-BDL2-WP12G-CHI, ISC-BDL2-CB12G-CHI] Installation/configuration notes Coverage Patterns 94° 2 | Blue Line Gen2 TriTech Motion Detectors Mounting The recommended mounting height is 2.2 m to 2.75 m (7.5 ft to 9 ft) with no adjustments required. Mount the motion detector level, both horizontally and vertically. Mounting options: • On a flat wall (surface, semi-flush), with the optional B335-3 Swiveling low-profile mount, or with the optional B328 Gimbal-mount Bracket • In a corner (the junction of two perpendicular walls) • On the ceiling with the optional B338 Universal Ceiling-mount Bracket Technical specifications Electrical Current (alarm/standby)10 mA at 12 VDC Voltage (operating)9 VDC to 15 VDC Environmental Pet Immunity1 One or two pets up to 45 kg (100 lb) or numerous rodents Relative Humidity 0 to 95%, non-condensing For UL Listed product installations 0 to 85%, non-condensing Temperature (operating)G models = - 20°C to + 55°C (- 4°F to + 131°F) GE models = - 10°C to + 55°C HE models= + 5°C to + 40°C UL/ C-UL= 0°C to + 49°C (+32°F to + 120°F) 1 Applies to the Pet Friendly models only and only when the Pet Immunity feature is turned on. Mechanical Color white Dimensions 105 mm x 61 mm x 44 mm (4.2 in. x 2.4 in. x 1.7 in.) Material High-impact ABS plastic Outputs Relay Solid state, supervised, Form A normally-closed (NC) contacts rated for ≤100 mA, 25 VDC, 2.5 W, <20 Ω closed Tamper Normally-closed (NC) contacts (with cover on) rated for ≤100 mA, 25 VDC, 2.5 W Connect tamper circuit to 24-hour protection circuit. 3 | Blue Line Gen2 TriTech Motion Detectors Ordering information ISC-BDL2-W12G Motion detector, 40ft (12m) Provides PIR and microwave, 12 m x 12 m (40 ft x 40 ft) coverage. Frequency: 10.525 GHz Order number ISC-BDL2-W12G ISC-BDL2-WP6G Motion detector, pet friendly, 20ft (6m) Provides Pet Friendly PIR and microwave, 6 m x 6 m (20 ft x 20 ft) coverage. Frequency: 10.525 GHz Order number ISC-BDL2-WP6G ISC-BDL2-WP12G Motion detector, pet friendly 40ft (12m) Provides Pet Friendly PIR and microwave, 12 m x 12 m (40 ft x 40 ft) coverage. Frequency: 10.525 GHz Order number ISC-BDL2-WP12G ISC-BDL2-WP6G-CHI Motion detector, pet friendly, 20ft (6m) Provides Pet Friendly PIR and microwave, 6 m x 6 m (20 ft x 20 ft) coverage. For use in China. Frequency: 10.525 GHz Order number ISC-BDL2-WP6G-CHI ISC-BDL2-WP12G-CHI Motion detector, pet friendly 40ft (12m) Provides Pet Friendly PIR and microwave, 12 m x 12 m (40 ft x 40 ft) coverage. For use in China. Frequency: 10.525 GHz Order number ISC-BDL2-WP12G-CHI ISC-BDL2-W12GE Motion detector, 40ft (12m) Provides PIR and microwave, 12 m x 12 m (40 ft x 40ft) coverage. Frequency: 10.510 to 10.580 GHz Order number ISC-BDL2-W12GE ISC-BDL2-W12HE Motion detector, 12m, FR Provides PIR and microwave, 12 m x 12 m (40 ft x 40 ft) coverage. For use in France. Frequency: 10.570 to 10.610 GHz Order number ISC-BDL2-W12HE ISC-BDL2-WP12GE Motion detector, pet friendly 40ft (12m) Provides Pet Friendly PIR and microwave, 12 m x 12 m (40 ft x 40 ft) coverage. Frequency: 10.510 to 10.580 GHz Order number ISC-BDL2-WP12GE ISC-BDL2-WP12HE Motion detector, pet friendly, 12m, FR Provides Pet Friendly PIR and microwave, 12 m x 12 m (40 ft x 40 ft) coverage. For use in France. Frequency: 10.570 to 10.610 GHz Order number ISC-BDL2-WP12HE Accessories B328 Mounting bracket, gimbal Mounts on a single-gang box and allows rotation of a detector. Wires are hidden inside. Order number B328 B335-3 Mounting bracket, swivel, low profile Swiveling, low-profile, universal bracket for wall mounting. The vertical swivel range is +10° to -20°, while the horizontal swivel range is ±25°. Order number B335-3 B338 Mounting bracket, ceiling, universal Swiveling universal bracket for ceiling mounting. The vertical swivel range is +7° to -16°, while the horizontal swivel range is ±45°. Order number B338 4 | Blue Line Gen2 TriTech Motion Detectors Represented by: Europe, Middle East, Africa:Germany:North America:Asia-Pacific: Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven, The Netherlands Phone: + 31 40 2577 284 emea.securitysystems@bosch.com emea.boschsecurity.com Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.com Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, New York, 14450, USA Phone: +1 800 289 0096 Fax: +1 585 223 9180 onlinehelp@us.bosch.com www.boschsecurity.us Robert Bosch (SEA) Pte Ltd, Security Systems 11 Bishan Street 21 Singapore 573943 Phone: +65 6571 2808 Fax: +65 6571 2699 apr.securitysystems@bosch.com www.boschsecurity.asia © Bosch Security Systems 2020 | Data subject to change without notice 2612755083 | en, V36, 13. Mar 2020 Siren & Stainless Steel Enclosure ELK-150RT Features Specifications The ELK-150RT is a self-contained Siren in a corrosion and tamper resistant enclosure. It features two sealed reed tamper switches, one on the Back plate and one on the Front Cover. The switches are normally closed and pre-wired in series. The ELK-150RT can produce two distinct sounds from a single input trigger. The stainless steel exterior reflects the color of the mounting surface allowing the ELK-150RT to blend easily with any residential or commercial building. Also available is the ELK-45 which is the self contained siren without the stainless enclosure; the ELK-SL1 Strobe Light which can be added to the enclosure, and the ELK-1RT which is a 30 watt speaker in the stainless enclosure. The ComboTrigger™ option allows controls which have a single alarm output and pulsing option to activate both the burglar and fire alarm sounds. • Installer Friendly - Easy to Mount. • Sealed Reed Tamper Switches at single bolt closure and at rear of cabinet. • Corrosion Resistant- Exterior / Interior use. • Compact - Less Noticeable. • Loud - Rivals Sound of Larger Speakers. • Heavy Duty 1.8 lb Magnet. • ComboTrigger™ For Single Outputs. • Stainless Mounting Hardware Included. • Lifetime Limited Warranty. ELK PRODUCTS, INC. PO Box 100 • Hildebran, NC 28637 • 800-797-9355 • 828-397-4200 Fax 828-397-4415 • www.elkproducts.com • info@elkproducts.com ELK-150RT with optional ELK-SL1C Clear Strobe Tamper-Proof Cover Self-Contained Siren & Speaker Hardware PakBack Plate w/ (2) Tamper SwitchesFeatures and Specifications subject to change without notice. Cut-away view Components of ELK-150 RT • Operating Voltage: 6 to 14 Volts D.C. • Current Draw: 1.2 Amps • Sound Level: 118 dB @ 1 meter, 14 Volts DC. • Enclosure: #304 Stainless Steel. • Size: 5”H x 5”W x 4”D. 12/15 Instructions ELK-150RT Install top edge of backplate at least 1” below any soffit or building overhang.The ELK-150 RT is a self-contained siren in a tampered, corrosion resistant stain-less steel enclosure. It incorporates two sealed reed tamper switches for enhanced reliability and ease of use. 1. Using the backplate as a template, mark and drill the 4 mounting holes and the wire or conduit entry hole (see Figure 1). Insert the (4) 1/4 x 1” wall anchors, then partially install the top two #10 x 1” screws. 2. Route the wire or conduit through the hole provided and hang backplate on the top screws. Then install remaining two screws and & tighten all four. 3. Temporarily hang the Siren/speaker on the backplate by aligning the slotted in-sert on the top edge of the Siren with the 1/2” recessed tab on the bottom edge of the backplate. Press Siren onto tab. (See Figure 2) 4. Connect the two white wires from the tamper switches to a 24 hour closed loop on the control panel (the switches are already connected in series). 5. Connect the Red (+) and Black (-) wires from the Siren to the control’s alarm output. The Siren produces a Yelp sound from a constant voltage input. If the voltage input is pulsed the siren produces a low pitch rise. This ComboTrig-gerTM feature allows two sounds to be activated by a control that has only a sin-gle alarm output with a pulse option. Recommended wire gauge from control is 18 AWG. NEG (-) Black = Negative (-) terminal from Control’s Alarm output. YELP (+) RED = Positive (+) terminal from Control’s Alarm output 6. Move the Siren/speaker from its hanging position to its final mount by aligning it’s top and bottom slots with the 1/2” tabs on the top edge of the backplate and in the bottom center above the bolt threads. (See Figure 3) Press firmly. 7. Slide front cover over speaker. Lift up to engage the tabs in the cover with the two “U” shaped slots on the top edges of the backplate. (Figure 4) Lower cover until tabs are in slots. Push cover towards wall, then lift up to lock tabs in slots. Thread 1/4-20 hex bolt into hole on bottom of cover and tighten until secure. 8. The front cover tamper switch is pressed closed by the front cover during the final 3 to 4 full turns of the hex bolt. If possible, test the operation of the tamper switch using a continuity meter. Note: The ELK-150RT is designed for Single Output Alarm Controls that use a STEADY Output for BURG or a PULSING Output for FIRE. For an Alarm Con-trol panel that has separate BURG and FIRE alarm outputs connect the Red wire to each output, then program one output for Steady(Burg) and the other for Pulsing(Fire). Connect the Black wire to Neg. INSTALLATION OF THE ELK-150RT SIREN Figure 1 Tuck wires into lower corner of backplate away from top inside corners. Figure 3 Figure 2 White White Black Red POWER to SIREN ELK‐902 TAMPER LEADS ELK‐902 ELK‐902 ELK‐902 ELK‐902 Wall Mounting Holes Electrical Box Mounting Holes Wire / Conduit Entry Figure 4 Slide over speaker.Lower tabs into slots.Push towards wall.Lift up to lock, then secure with hex bolt. Tamper switch is closed by the front cover during the final 3 to 4 turns of the hex bolt. WWW.SDCSECURITY.COM µ SECURITY DOOR CONTROLS Security Door Controls ACCESS & EGRESS SOLUTIONS - THE LOCK BEHIND THE SYSTEM 1 400 Series Wall & Frame LED Status Indicators • Easy to Install • Single Gang or Narrow Frame Mount • Multi Color LED Technology FEATURES MODELS 400U-L2 SDC Monitor Station, 1-Gang, (2) LED’s 400NU-L2 SDC Monitor Station, Narrow Plate, (2) LED’s 400U-L3 SDC Monitor Station, 1-Gang, (3) LED’s 400U-LT1 SDC Monitor Station, 1-Gang, (1) Tri-Color LED, Red, Green, Amber 400U-LT2 SDC Monitor Station, 1-Gang, (2) Tri-Color LED, Red, Green, Amber SPECIFICATIONS Faceplate Stainless Steel Dual Voltage 12/24VDC, 20 mA per LED Weight 1.0 lbs The SDC 400U Status Indicator are used for single gang and nar- row frame mount assemblies. It is equipped with LED status indicators to provide indication of door or lock status. W ARRA N TYYEAR5S ELECT A B LEFIELD1224 © 2017 SECURITY DOOR CONTROLS µ WWW.SDCSECURITY.COM Security Door Controls LIT-400 SERIES ANNUNCIATORS 01/17 [t] 800.413.8783 µ 805.494.0622 µ [f] 866.215.3138 µ 801 Avenida Acaso, Camarillo, CA 93012 µ PO Box 3670, Camarillo, CA 93011 400 Series Wall & Frame Mount Sirens & Buzzers • Easy to Install • Single Gang or Narrow Frame Mount • Buzzer or Siren Alert Warning FEATURES MODELS 400U-RMB SDC Alarm Station, 1-Gang, Buzzer 86dbA, 24 mA @ 24VDC 400NU-RMB SDC Alarm Station, Narrow 1-3/4”, SS, Buzzer 86dbA, 24 mA @ 24VDC 400U-SN SDC Alarm Station, 1-Gang, Siren 85 db, 18mA @ 24VDC 400NU-SN SDC Alarm Station, Narrow 1-3/4”, Siren 85 db, 18mA @ 24VDC SPECIFICATIONS Faceplate Stainless Steel Dual Voltage 12/24VDC Weight 1.0 lbs The SDC 400 Siren and Buzzer Series are used for single gang or narrow frame mount assemblies to provide indication of door open or unlocked status. 400U-SN 400NU-SN 400U-RBM 400NU-RBM W ARRA N TYYEAR5