HomeMy WebLinkAboutAPPROVED Updated POLY MOD BIT APPROVAL PG 1,4,27 highlighted EXTERIOR RESEARCH& DESIGN, LLC.
Certificate of Authorization#9503
TRINITY ERD 353 Christian Stree
Oxford, CT 0647t
(203)2629245
EVALUATION REPORT
Polyglass USA, Inc. Evaluation Report P9290.02.08-R20
150 Lyon Drive FL1654-1122
Fernley, NV 89408 Date of Issuance:02/11/2008
(570)384-1230 Revision 20:09/12/2017
SCOPE:
This Evaluation Report is issued undkete 61G20-3 and the applicable rules and regulations governing the us,
construction materials in the State of Florida. The documentation stWxInhas been reviewed by Robert Niemine
P.E. for use of the product under the Florida Building Code. The product described herein havdJeated for
compliance,Nith the 6`"Edition (2017) Florida Building Code sectons noted herein
DESCRIPTION: Polyglass SBS and APP Modified Bitumen Roof Systems
LABELING: Labeling shall bein accordance with the requirements the Accredited Quality Assurance Agency
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the ralapneduct(s) changes, the referent(
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Accer
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.F.pifotluct
changes or the referenced Quality Assurance documentation charTge-EityJERD requires a complete review of tl-
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preced*the words "Trinity I ERDEvaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall bei#d4o the user by the manufacturer c
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 thr( iagfhus a58-page Appendix.
Prepared by:
= 07 �.
.o -
fi yV r
Robert J.M. Nieminen,P.E.
_�,l�«rre „o Thefacsimileseal appearing was authorizb#Robert Nieminen,
Florida Registration No.59166,Florida DCA ANE1983 P.E.or09/12/2017.This does not serve as an electronically signet
document.
CERTIFICATION OF INDEPENDENCE:
1. ExteriorResearch & Design, LLC. d/Thzinity I ERDioes not have, nor does it intend to acquire or will it acquire, a financial inte
in any company manufacturing or distributing products it evaluates.
2. Exterior Research & Design, LLC. d/Winity I ERDis rot owned, operated or controlled by any company manufacturing
distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributietg hoc
which the evaluationffports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the apprezElgdrttme
product.
5. This is a building code evaluation. NeitheinTyIERDnor Robert NiemineriP.Eare, in any waythe Designer of Record for an
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless
specifically for that purpose.
TRINITY ERD
ROOFING SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub-Category: Modified BitumenRoof Systems
Compliance Statement: Polyglass SBS and APP Modified Bitumen Roof Systems, as produced b?olyglass USA,
Inc., have demonstrated compliance with the following sections of SITeEdition (2017) Florida Building Code
through testing in accordance with the following Standards. Compliance is subject to the Installation Requir
and Limitations/Conditions of Use set forth herein.
2. STANDARDS:
Section Property Standard Year
1504.3.1 Wind FM 4474 2011
1504.3.1 Wind UL 1897 2012
1504.7 Impact FM 4470 2012
1507.11.2 Physical Properties ASTM D6162 2008
1507.11.2 Physical Properties ASTM D6163 2008
1507.11.2 Physical Properties ASTM D6164 2011
1507.11.2 Physical Properties ASTM06222 2011
1507.11.2 Physical Properties ASTM D6509 2009
3. REFERENCES:
Entity Examination Reference Date
ERD (TST6049) Physical Properties P10490.10.M 10/30/2008
ERD (TST6049) FM 44704474 P13760.09.09 09/10/2009
ERD (TST6049) FM 44704474 P13770.09.09 09/10/2009
ERD (TST6049) FM 44704474 P30540.11.09t1 11/30/2009
ERD (TST6049) FM 44704474 P30550.12.09 12/02/2009
ERD (TST6049) Physical Properties P33960.12.10 12/30/2010
ERD (TST6049) FM 44704474 P3397003.11 03/15/2011
ERD (TI1049) Physical Properties P37590.03.13A 03/06/2013
ERD (TST6049) FM 4470/4474 P39680.03.13 03/04/2013
ERD (TST6049) Physical Properties P37590.03.1.31-R1 06/26/2013
ERD (TST6049) Physical Properties P37590.03.142-R1 07/01/2013
ERD (TST6049) PhWical Properties P37590.07.1T 07/01/2013
ERD (TST6049) Physical Properties P37590.03.1-1-R1 07/01/2013
ERD (TST6049) Physical Properties P37590.07.1-31 07/02/2013
ERD (TST6049) FM 4470/4474 P41630.08.13 08/06/2013
ERD (TST6049) Physical Propedis P45940.09.13 09/04/2013
ERD (TST6049) Physical Properties P44370.10.13 10/04/2013
ERD (TST6049) Physical Properties P39520.09.112 09/11/2014
ERD (TST6049) FM 4470/4474 SC6160.11.14 11/10/2014
ERD (TST6049) Physical Properties PLYCP45440SC.03511 03/31/2015
ERD (TST6049) Physical Properties SC5170.05.15 05/08/2015
ERD (TST6049) FM 4474 SC8085.05.15 05/19/2015
ERD (TST6049) Physical Properties SC5170.12.15 12/29/2015
ERD (TST6049) FM 4470/4474 SC9455.15 04/01/2016
ERD (TST6049) FM 44704474 PLY(93C890S)5.16-1 05/17/2016
ERD (TST6049) FM 4470/4474 PLY(93C890ff)5.16-2 05/17/2016
ERD (TST6049) FM 4470/4474 PLYGISC10815.07AR1 09/23/2016
ERD (TST6049) UL 1897 PLYGBC12025.10.16 10/12/2016
ERD (TST6049) FM 4470/4474 PLYGBC11475.8 11/17/2016
ERD (TST6049) FM 4470/4474UL1897 PLY(93C13235.01.17 01/17/2017
ERD (TST6049) FM 4474UL1897/TAS 114 PLY(93C13920.05.17 05/30/2017
ERD JS!11294) FM 4474UL1897/TAS 114 PLY(ETL13945.05.17 05/30/2017
Exterior Research and Design,LLC. Evaluation Report P9290.02.08-R20
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL1654-R22
Polyglass Modified Bitumen Roof Systems;(570)384-1230 Revision 20:09/12/2017
Page 2 of 6
TRINITY ERD
Entity Examination Reference Date
ERD (T9-T129,� FM 4474UL1897/TAS 14 PLYG;TL13945.05.13 05/30/2017
ERD (TST6049) FM 4474UL1897 PLYgo'C13945.05.17 05/30/2017
ERD (TST6049) FM 4474TAS 114 PLYgo'C15760.09.17 09/11/2017
FM Approvals(TST1867) FM 4470 2W7A7.AM 08/04/1994
FM Approvals(TST1867) FM 4470 OD3A3.AM 04/04/1997
FM Approvals(TST1867) FM 4470 2DOAO.AM 12/23/1998
FM Approvals(TST1867) FM 4470 2D5A9.AM 06/22/1999
FM Approvals(TST1867) FM 4470 3006646 01/04/2000
FM Approvals(TST1867) FM 4470 3001334 01/25/2000
FM Approvals(TST1867) FM 4470 3001334 02/15/2000
FM Approvals(TST1867) FM 4470 3000857 01/12/2000
FM Approvals(TST1867) FM 4470 3004091 01/12/2000
FM Approvals(TST1867) FM 4470 3006115 05/02/2001
FM Approvals(TST1867) FM 4470 3012321 07/29/2002
FM Approvals(TST1867) FM 4470 3014692 08/05/2003
FM Approvals(TST1867) FM 4470 3014751 08/27/2003
FM Approvals(TST1867) FM 4470 3007170 01/13/2004
FM Approvals(TST1867) FM 4470 3019317 06/30/2004
FM Approvals(TST1867) FM 4470 3020703 07/30/2004
FM Approvals(TST1867) FM 4470/4474 3018332 01/31/2006
FM Approvals(TST1867) FM 4470/4474 3023368 03/20/2006
FM Approvals(TST1867) FM 4470/4474 3024594 05/23/2006
FM Approvals(TST1867) FM 4470/4474 3023458 07/18/2006
FM Approvals(TST1867) FM 4470/4474 3030668 09/12/2007
FM Approvals(TST1867) FM 4470/4474 3032172 06/12/2009
FM Approvals(TST1867) FM 4470/4474 3049631 04/21/2014
FM Approvals(TST1867) FM 4470/4474 3057029 02/02/2017
PRI (TST5878) Physical Properties PUSP062-02-01 12/04/2007
PRI (TST5878) Phjsical Properties PUSP061-02-02 01/28/2008
PRI (TST5878) Physical Properties PUSP064-02-02 02/27/2008
PRI (TST5878) Physical Properties PUSP06202-02 12/04/2008
PRI (TST5878) TAS 114 PUSA188-02-01 02/08/2017
PRI (TST5878) TAS 114 PUSA188-02-02 02/08/2017
PRI (TST5878) TAS 114 PUSA188-02-03 02/08/2017
PRI (TST5878) TAS 114 PUSP20202-01 05/17/2017
PRI (TST5878) TAS 114 PUSP20202-02 05/17/2017
Miami-Dade(CER1592) HVHZ Compliance Various NOAs Various
Miami-Dade(CER1592) Proposal fo Review 10-0823 10/12/2010
UL LLC (QUA9625) Quality Control Service Confirmation, R14571 Exp. 10/06/2018
4. PRODUCT DESCRIPTION:
This Evaluation Report covers Polyglass Modified Bitumen Roof Systems installed in accordance with Polyc
Inc. published installation instructions and the Limitations / Conditions of Use herein. The following Po
membranes make up the subject systems.
TABLE 1:ROLL-GOODS FOR POLYGLASS MODIFIED BITUMEN ROOF SYSTEMS
Type Product Specification
Reference Grade Type
Polyglass G2 Base ASTM D4601 N/A II
Base Sheets Polyflex SA Base ASTM D4601 N/A 11
Polyglass APP Base ASTM D6509 N/A N/A
Exterior Research and Design,LLC. Evaluation Report P9290.02.08-R20
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL1654-R22
Polyglass Modified Bitumen Roof Systems;(570)384-1230 Revision 20:09/12/2017
Page 3 of 6
QOTRINI-FY ' ERD
TABLE 1(CONTINUED):ROLL-GOODS FOR POLYGLASS MODIFIED BITUMEN ROOF SYSTEMS
Type Product Specification
Reference Grade Type
Polyglass HT Base 650 ASTM D6162 S III
Elastobase ASTM D6163 S I
Elastoflex V ASTM D6163 S I
Elastoflex SA V Base ASTM D6163,Table S I
Elastoflex SA V FIR Base ASTM D6163,Table S I
SBS Membranes Elastoflex SA V Plus ASTM D6163 S I
Elastoflex SA V Plus FIR ASTM D6163 S I
Elastobase Poly ASTM D6164 S I
Elastoflex S6 ASTM D6164 S I
Elastoflex SType II ASTM D6164 S II
Elastoflex VG ASTM D6163 G I
Elastoflex VG FIR ASTM D6163 G I
Elastoflbx S6 G ASTM D6164 G I
Elastoflex S6 G FIR ASTM D6164 G I
Polyfresko G SBS(sand or pfdtp backed) ASTM D6164 G I
Polyfresko G SBS FIR(sand or-pkdybacked) ASTM D6164 G I
SBS Membranes Elastoshield TS G ASTM D6164 G I
Elastoshield TS G FIR ASTM D61,6 G I
Elastoflex SA P ASTM D6164 G I
Elastoflex SA P FIR ASTM D6164 G I
Polyreflect ASTM D6164 S I
Polyflex ASTM D6222 S I
Polyflex G ASTM D6222 G I
Polyflex G FIR ASTM D6222 G I
Polyfresko G ASTM D6222 G I
Polyfresko GAF ASTM D6222 G I
APP Membranes Polybond ASTM D6222 S I
Polybond G ASTM D6222 G I
Polyflex SA P ASTM D6222 G I
Polyflex SA P FIR ASTM D6222 G I
Polyfresko G SA ASTM D6222 G I
Polykool ASTM D6222 S I
S. LIMITATIONS:
5.1 This is a building code evatim. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/w,
for permitting or design guidance unless retained specifically forobgbose.
5.2 This Evaluation Report is not for us4BC HVHZ jurisdictions.
5.3 Refer to a currenApprovedRoofing Materials Directory for fire ratings of this product.
5.4 For steel deck installations, foam plastic insulation shall be sepafededthe building interior in accordanc
with FBC 2603.4 unless the exceptions stated IiIBC 2603.4.1 and 2603.6 apply.
5.5 The roof system evaluation herein pertains to abckeEk roof components. Roof decks and structu
members shall be in accordes with FBC requirements to the satisfaction of tnothority Having
Jurisdiction Load resistance of the roof deck shall be documented through proper codified and/o
Approval documentation
5.6 For recover installations, the existing roof shalldxemined in accordance wiftBC 1511.
Exterior Research and Design,LLC. Evaluation Report P9290.02.08-R20
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL1654-1122
Polyglass Modified Bitumen Roof Systems;(570)384-1230 Revision 20:09/12/2017
Page 4 of 6
TRINITY ERD
5.7 For mechanically attached insulation or membrane or slbdpded insulation, the maximum design pressL
for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordar
FBCChapter 16. Zones 2 and 3 shall employ an attachment density designed by a qualified
professional to resist the elevated pressure criteria. Commonly used methoallmf/SPRI WD1, FM Loss
Prevention Data Sheet 1-29, Roofing Application Standard RAS 117 and Roofing Application Standard RAS
137. Assemblies marked with an asterisk* carry the limitations set fortaebtion 2.2.10.1 of FM Loss
Prevention Data Sheet 1-29(January 2016)for Zone 2/3 enhancements.
5.8 For assemblies with all compclnlis fully bonded in place, the maximum design pressure for the sele
assembly shall meet or exceed critical design pressure determined in accord an cREC/itha pte r 16. No
rational analysis is permitted for these systems.
5.9 For mechanically attadefd insulation or membrane over existing roof decks, fasteners shall be tested i
existing deck for withdrawal resistance. A qualified design professional shall review the data for coml
to the minimum requirements for the system. Testing and Ilia shall be in accordance wi#NSI/SPRI
FX-1 or Testing Application Standard TAS 105.
5.10 For bonded insulation or membrane over existing substrates ir+rao-b(tear off) or recover installation, thl
existing deck or existing roof surface shall mined for compatibility with the adhesive to be installed.
any surface conditions exist that bring system performance into question, field uplift testing in accor
with ANSI/SPRI IA-1,ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS
124 shall be conducted on moalgps of the proposed new roof assembly.
5.11 For bonded insulation or membrane over existing substrates in a recover installation, the existin
system shall be capable of resisting project delssures on its own merit to the satisfaction of tl
Authority Having Jurisdictigras documented through field uplift testing in accordance \A$FM E907, FM
Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124.
5.12 Metal edge attahment (except gutters), shall be designed and installed for wind loads in accordance
FBC Chapter 16 and tested for resistance in accord anceAW9tJSPRI ES-1 or Roofing Application Standard
RAS 111, except the basic wind speed shall be determinednf FBC Figure 1609.3(1), 1609.3(2) or
1609.3(3).
5.13 All products in the roof assembly shall have quality assurance in accordancliAl'riftle 61G20-3.
6. INSTALLATION:
6.1 Polyglass Modified Bitumen Roof Systems shall be installed in accord an cetia✓Polyglass USA, Inc. published
installation instructions, subject to the Limitations/Conditions of Use ntatedin.
6.2 System attachment requirements for wind load resistance are set forth in Appencr[MIDP" = Maximum
Design Pressure is the resulittasting for wind load resistance based on allowable wind loads, and ref
the ultimate passing pressure divided by 2 (the 2 to 1 margin of safet�FgZr1504.9 has already beer
applied) Refer toFBC 1609 for determination of design wind loads.
Exterior Research and Design,LLC. Evaluation Report P9290.02.08-R20
Certificate of Authorization#9503 6"'EDITION(2017)FBC NON-HVHZ EVALUATION FL1654-1122
Polyglass Modified Bitumen Roof Systems;(570)384-1230 Revision 20:09/12/2017
Page 5 of 6
TRINITY ERD
6.3 Anyof the following FBC Approved coatings may be applied to the top roof membrane without adverse
on the system wind load performance. Refer to current Roofing Materials Directory for fire ratings ass(
with coating usage.
➢ PG200 NofFibered RooCoating;
➢ PG300 Fibered Roof Coating;
➢ PG600 NofFibered Aluminum Roof Coating;
➢ PG650 Fibered Aluminum Roof Coating;
➢ PG70CHigh Quality Elastomeric Roof CoatoTgKM Acryl 25
➢ PG700QS (Qui6&et) High Quality Elastomeric Roof Coabn f M Acryl 2-US(over granulesurfaced
APFbr SBS)nly);
➢ PG800 Asphalt Emulsion Roof Coating;
➢ Polyplus 60 Premium Ne iibered Aluminum Roof Coating;
➢ Polyplus 65 Premium Fibered Aluminum Roof Coating;
➢ Polybrite 70Premium GraddElastomeric Roof Coatirmg KM Acryl 15
➢ Polybrte 70QS (QuicBet) Premium Grade Elastomeric Roof CoadingM Acryl 1-US(over granule
surfaced APOr SBS)nly);
➢ Polybrite 90High Solids Silicone Roof Coating;
➢ Polybrite 95Silicone Roof Coating
7. BUILDING PERMIT REQUIREMENTS:
As required by thElBuilding Official or Authority Having Jurisdiction in order to properly evaluate the installatil
this product.
8. MANUFACTURING PLANTS:
Contact the noted QA agency for information on product locations covered Ff4rc. Rule 61G20-3 QA
requirements
9. QUALITY ASSURANCE ENTITY:
UL LLG QUP962� (314) 5783406, k.chancellor@us.ul.com
-THE 58-PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT-
Exterior Research and Design,LLC. Evaluation Report P9290.02.08-R20
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION FL1654-R22
Polyglass Modified Bitumen Roof Systems;(570)384-1230 Revision 20:09/12/2017
Page 6 of 6
QO
TRINITY ERD
I
APPENDIX 1:ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE
Table Deck Application Type Description Page
1A Wood New or Reroof(Tear-Off) A-1 Bonded Insulation,Bonded Roof Cover 5
16-1 Wood New or Reroof(Tear-Off) A-2 Mech.Attached Anchor Sheet,Bonded Insulation,Bonded Roof Cover 5-9
16-2 Wood New,Reroof(Tear-Off)or Recover A-2 Mech.Attached Anchor Sheet,Bonded Insulation,Bonded Roof Cover 10-11
1C Wood New,Reroof(Tear-Off)or Recover B Mech.Attached Base Insulation,Bonded Top Insulation,Bonded Roof Cover 11
11) Wood New,Reroof(Tear-Off)or Recover C Mech.Attached Insulation,Bonded Roof Cover 12-13
1E Wood New,Reroof(Tear-Off)or Recover D Prelim.Attached Insulation,Mech.Attached Base Sheet,Bonded Roof Cover 14-15
1F-1 Wood New or Reroof(Tear-Off) E Non-Insulated,Mech.Attached Base Sheet(nails),Bonded Roof Cover 16-18
1F-2 Wood New,Reroof(Tear-Off)or Recover E Non-Insulated,Mech.Attached Base Sheet(screws&plates),Bonded Roof Cover 19-21
1G Wood New or Reroof(Tear-Off) F Non-Insulated,Bonded Roof Cover 21
2A Steel or Structural concrete New,Reroof(Tear-Off)or Recover B Mech.Attached Base Insulation,Bonded Top Insulation,Bonded Roof Cover 22-24
2B Steel or Structural concrete New,Reroof(Tear-Off)or Recover C Mech.Attached Insulation,Bonded Roof Cover 25-28
2C Steel or Structural concrete New,Reroof(Tear-Off)or Recover D Prelim.Attached Insulation,Mech.Attached Base Sheet,Bonded Roof Cover 29-31
3A Structural concrete New or Reroof(Tear-Off) A-1 Bonded Insulation,Bonded Roof Cover 32-40
3B Structural concrete New or Reroof(Tear-Off) F Non-Insulated,Bonded Roof Cover 40
4A LWIC New or Reroof(Tear-Off) A-1 Bonded Insulation,Bonded Roof Cover 41-42
4B LWIC New or Reroof(Tear-Off) A-2 Mech.Attached Anchor Sheet,Bonded Insulation,Bonded Roof Cover 43
4C LWIC New or Reroof(Tear-Off) E Non-Insulated,Mech.Attached Base Sheet,Bonded Roof Cover 44-46
5A CWF New or Reroof(Tear-Off) A-1 Bonded Insulation,Bonded Roof Cover 47
5B CWF New,Reroof(Tear-Off)or Recover A-2 Mech.Attached Anchor Sheet,Bonded Insulation,Bonded Roof Cover 48
5C CWF New,Reroof(Tear-Off)or Recover B Mech.Attached Base Insulation,Bonded Top Insulation,Bonded Roof Cover 49
51) CWF New,Reroof(Tear-Off)or Recover C Mech.Attached Insulation,Bonded Roof Cover 49
5E CWF New,Reroof(Tear-Off)or Recover E Non-Insulated,Mech.Attached Base Sheet,Bonded Roof Cover 49
6A Gypsum Reroof(Tear-Off) A-1 Bonded Insulation,Bonded Roof Cover 50-52
6B Gypsum Reroof(Tear-Off)or Recover A-2 Mech.Attached Anchor Sheet,Bonded Insulation,Bonded Roof Cover 52
6C Gypsum Reroof(Tear-Off)or Recover C Mech.Attached Insulation,Bonded Roof Cover 53
6D Gypsum Reroof(Tear-Off)or Recover E Non-Insulated,Mech.Attached Base Sheet,Bonded Roof Cover 53
7A Various Recover A-1 Bonded Insulation,Bonded Roof Cover 54-58
7B Various Recover F Non-Insulated,Bonded Base Sheet,Bonded Roof Cover 58
The following notes apply to the systems outlined herein:
1. The roof system evaluation herein pertains to above-deck roof components. Roof decks and structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction.
Load resistance of the roof deck shall be documented through proper codified and/or FBC Approval documentation.
2. Insulation/base sheet fasteners shall be of sufficient length for the following deck engagement:
➢Wood: Minimum 0.75-inch penetration.
➢Steel: Minimum 0.75-inch penetration and engage the top flute of the steel deck.
➢Structural concrete: Minimum 1-inch embedment into pilot hole in accordance with fastener manufacturer's published installation instructions.
3. Unless otherwise noted, insulation may be any one layer or combination of polyisocya nu rate, polystyrene, wood fiberboard, perlite, gypsum-based roof board or mineral-wool roof board that meets the CIA
requirements of F.A.C.Rule 61G20-3 and is documented as meeting FBC 1505.1 and,for foam plastic,FBC Chapter 26,when installed with the roof cover.
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 1 of 58
0
TRINITY ERD
4. Minimum 200 psi, minimum 2-inch thick lightweight insulating concrete may be substituted for rigid insulation board for System Type D(mechanically attached base sheet,bonded roof cover),whereby the base
sheet fasteners are installed through the LWIC to engage the structural steel or concrete deck. The structural deck shall be of equal or greater configuration to the steel and concrete deck listings. Roof decks and
structural members shall be in accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction. Load resistance of the roof deck shall be documented through proper codified and/or FBC
Approval documentation.
5. Preliminary insulation attachment for System Type D:Unless otherwise noted,refer to Section 2.2.10.1.3 of FM Loss Prevention Data Sheet 1-29(January 2016).
6. Unless otherwise noted,insulation adhesive application rates are as follows. Ribbon or bead width is at the time of application;the ribbons/beads shall expand as noted in the manufacturer's published instructions.
➢ Hot asphalt(HA): Full coverage at 25-30 Ibs/square.
➢ Dow INSTA STIK Quik Set Insulation Adhesive(D-IS): Continuous 0.75 to 1-inch wide ribbons,12-inch o.c.
➢ Millennium One Step Foamable Adhesive(M-OSFA): Continuous 0.25 to 0.5-inch wide ribbons,12-inch o.c.
➢ Millennium PG-1 Pump Grade Adhesive(M-PG1): Continuous 0.25 to 0.5-inch wide ribbons,12-inch o.c.
➢ OMG OlyBond 500(OB500): Continuous 0.75 to 1-inch wide ribbons,12-inch o.c.(PaceCart or SpotShot). Note: OlyBond Green may be used where OlyBond 500 is referenced.
➢ OlyBond Classic(OB Classic): Full coverage at 1 gal/square.
➢ ICP Adhesive&Sealants CR-20: Continuous 2.5-3.5-inch wide ribbons,12-inch o.c.
➢ Note: When multiple layers(s)of insulation and/or coverboard are installed in ribbon-applied adhesive,board joints shall be staggered.
➢ Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation board shall be not less than one-half the specified ribbons spacing.
7. Unless otherwise noted,all insulations are flat-stock or taper board of the minimum thickness noted. Tapered polyisocyanurate at the following thickness limitations may be substituted with the following Maximum
Design Pressure(MDP)limitations. In no case shall these values be used to'increase'the MDP listings in the tables;rather if MDP listing below meets or exceeds that listed for a particular system in the tables,then
the thinner board listed below may be used as a drop-in for the equivalent thicker material listed in the table:
➢ Millennium One Step Foamable Adhesive(M-OSFA): MDP -157.5 psf (Min.0.5-inch thick)
➢ Millennium PG-1 Pump Grade Adhesive(M-PG1): MDP -157.5 psf (Min.0.5-inch thick)
➢ OMG OlyBond 500(OB500): MDP -45.0 psf (Min.0.5-inch thick Multi-Max FA-3)
➢ OMG OlyBond 500(OB500): MDP -187.5 psf (Min.0.5-inch thick ISO 95+GL)
➢ OMG OlyBond 500(OB500): MDP -315.0 psf (Min.0.5-inch thick ENRGY 3)
➢ OMG OlyBond 500(OB500): MDP -487.5 psf (Min.0.5-inch thick ACFoam II)
➢ ICP Adhesives&Sealants CR-20: MDP -117.5 psf (Min.1.0-inch thick)
8. Bonded polyisocya nu rate insulation boards shall be maximum 4 x 4 ft.
9. For mechanically attached components or partially bonded insulation,the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with FBC
Chapter 16, and Zones 2 and 3 shall employ an attachment density designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss
Prevention Data Sheet 1-29, Roofing Application Standard RAS 117 and Roofing Application Standard RAS 137. Assemblies marked with an asterisk*carry the limitations set forth in Section 2.2.10.1 of FM Loss
Prevention Data Sheet 1-29(January 2016)for Zone 2/3 enhancements.
10. For fully bonded assemblies,the maximum design pressure for the selected assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16,and no rational analysis is permitted.
11. For mechanically attached components over existing decks,fasteners shall be tested in the existing deck for withdrawal resistance. A qualified design professional shall review the data for comparison to the
minimum requirements for the system. Testing and analysis shall be in accordance with ANSI/SPRI FX-1 or Testing Application Standard TAS 105.
12. For existing substrates in a bonded recover or re-roof installation,the existing roof surface or existing roof deck shall be examined for compatibility and bond performance with the selected adhesive,and the existing
roof system(for recover)shall be capable of resisting project design pressures on its own merit to the satisfaction of the Authority Having Jurisdiction,as documented through field uplift testing in accordance with
ANSI/SPRI IA-1,ASTM E907,FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124.
13. For Recover Applications using System Type D,the insulation is optional;however,the existing roof system shall be suitable for a recover application.
14. Lightweight Insulating Concrete(LWC)shall be cast in accordance with FBC Section 1917 to the satisfaction of the Authority Having Jurisdiction. For systems where specific LWC is referenced,refer to current LWC
Product Approval for specific deck construction and limitations. For systems where specific LWC is not referenced,the minimum design mix shall be 300 psi. In all cases,the minimum top-coat thickness is 2-inches.
For LWC over structural concrete,reference is made to FBC Section 1917.4.1,Point 1.
Exterior Research and Design,LLC.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 2 of 58
QO
TRINITY ERD
15. Unless otherwise noted,refer to the following references for bonded base,ply or cap sheet applications.
TABLE 1:POLYGLASS ROOF COVERS
Reference Layer Material Application
BP-AA Base Ply One or more plies Polyglass G2 Base,FBC Approved ASTM D4601,Type II
(Base and Ply sheets,Asphalt- Ply One or more plies Polyglass Ply IV,Polyglass Ply VI,FBC Approved ASTM D2178,Type IV or VI Hot Asphalt at 20 40
Ibs/square
Applied) Note: Asphalt-applied sheets or insulation shall not be applied to poly film surfaced membranes.
Base Ply One ply Elastobase(sand/sand),Elastoflex V,Elastoflex S6,Elastoflex S6 Type II,Polyglass HT Base 650 PG350 at 1.5-2.0
SBS-CA1 Cap Ply Elastoflex VG,Elastoflex VG FR,Elastoflex S6,Elastoflex S6 Type II,Elastoflex S6 G,Elastoflex S6 G FR,Elastoshield TS-G,Elastoshield gal/square
TS-G FR,Polyfresko G SBS(sand-backed),Polyfresko G SBS FR(sand-backed)
Base Ply One ply Elastobase(sand/sand),Elastoflex V,Elastoflex S6,Elastoflex S6 Type II Polyplus 35 at 1.5-2.0
SBS-CA2 Cap Ply Elastoflex VG,Elastoflex VG FR,Elastoflex S6,Elastoflex S6 Type II,Elastoflex S6 G,Elastoflex S6 G FR,Elastoshield TS-G,Elastoshield gal/square
TS-G FR,Polyfresko G SBS(sand-backed),Polyfresko G SBS FR(sand-backed)
Base Ply or Ply One or more plies Elastobase(sand/sand or poly/sand),Elastobase P(sand/sand or poly/sand),Elastoflex V,Elastoflex 56,Elastoflex
56 Type II,Polyglass HT Base 650
SBS-AA Elastoflex V,Elastoflex VG,Elastoflex VG FR,Elastoflex S6,Elastoflex S6 Type II,Elastoflex 56 G,Elastoflex S6 G FR,Elastoshield TS-G, Hot Asphalt at 20-40
(SBS,Asphalt-Applied) Cap Ply Elastoshield TS-G FR,Polyfresko G SBS(sand-backed),Polyfresko G SBS FR(sand-backed) Ibs/square
Note: Asphalt-applied sheets or insulation shall not be applied to poly film surfaced membranes.
Base Ply or Ply One
or more plies Elastobase(sand/poly),Elastobase(poly/poly),Elastoflex V,Elastoflex S6,Elastoflex S6 Type II,Polyglass HT Base
SBS-TA
Torch-Applied
(SBS,Torch-Applied) Elastoflex V,Elastoflex VG,Elastoflex VG FR,Elastoflex S6,Elastoflex S6 Type II,Elastoflex S6 G,Elastoflex S6 G FR,Elastoshield TS-G,
Cap Ply Elastoshield TS-G FR,Polyfresko G SBS(poly-film backed),Polyfresko G SBS FR y (p y ) y (poly-film backed)
Base Ply One or more plies Elastoflex SA V Base,Elastoflex SA V FR Base,Elastoflex SA V Plus,Elastoflex SA V Plus FR
SBS-SA Cap Ply Elastoflex SA P,Elastoflex SA P FR,Polyreflect Self-Adhering
(SBS,Self-Adhering) Unless otherwise noted,permissible membrane substrates for SBS-SA are limited to the SBS-SA Base Ply options herein,
Note: Elastobase of sand or Elastobase of of
(P Y/ ) (P Y/p YI
APP-CA1 Cap Ply Polyflex G FR PG350 at 1.5-2.0
gal/square
APP-TA Base Ply or Ply One or more plies Polyglass APP Base,Polyflex,Polybond
(APP,Torch-Applied) Cap Ply Polyflex,Polyflex G,Polyflex G FR,Polybond,Polybond G,Polyfresko G,Polyfresko G FR Torch-Applied
APP-SA Cap Ply Polyflex SA P,Polyflex SA P FR,Polyfresko G SA,Polykool
(APP,Self-Adhering) Note: Unless otherwise noted,permissible membrane substrates for APP-SAare limited to the SBS-SA Base Ply options herein, Self-Adhering
Elastobase(poly/sand)or Elastobase(poly/poly).
16. Any of the following FBC Approved coatings may be applied to the top roof membrane without adverse effect on the system wind load performance. Refer to current Roofing Materials Directory for fire ratings
associated with coating usage.
➢ PG200 Non Fibered Roof Coating;
➢ PG300 Fibered Roof Coating;
➢ PG600 Non-Fibered Aluminum Roof Coating;
➢ PG650 Fibered Aluminum Roof Coating;
➢ PG700 High Quality Elastomeric Roof Coating or KM Acryl 25;
➢ PG700QS(Quick Set)High Quality Elastomeric Roof Coating or KM Acryl 25-QS(for granule-surfaced APP or SBS only);
➢ PG800 Asphalt Emulsion Roof Coating;
➢ Polyplus 60 Premium Non-Fibered Aluminum Roof Coating;
➢ Polyplus 65 Premium Fibered Aluminum Roof Coating;
➢ Polybrite 70 Premium Grade Elastomeric Roof Coating or KM Acryl 15;
➢ Polybrite 70QS(Quick Set)Premium Grade Elastomeric Roof Coating or KM Acryl 15-QS(for granule-surfaced APP or SBS only);
➢ Polybrite 90 High Solids Silicone Roof Coating or Polybrite 95 Silicone Roof Coating.
Exterior Research and Design,LLC.d/b/a Trinity)ERD Evaluation Report P9290.02.08-R20 for FL1654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 3 of 58
QO
TRINITY ERD
17. Dens Deck shall be field-primed with PG100 prior to self-adhering membrane application. Refer to tables herein for other priming requirements.
18. Vapor barrier options for use over structural concrete deck followed by adhered insulation carry the following Maximum Design Pressure(MDP)limitations. The lesser of the MDP listings below vs.those in Table 3A
applies:
VAPOR BARRIER OPTIONS;STRUCTURAL CONCRETE DECK;ADHERED INSULATION PER TABLE 3A
Option# Primer Type Vapor Barrier Attach M Insulation Adhesive DP(psf)
VB-1. PG100 Elastoflex SA V Plus Self-Adhering Inta-Stik or CR-20,12-inch D.C. -60.0
VB-2. PG100 Polyglass APP Base Torch-applied Inta-Stik or CR-20,12-inch D.C. -75.0
VB-3. PG100 Elastoflex SA P Self-Adhering Insta-Stik,12-inch D.C. -75.0
VB-4. PG100 Elastoflex SA P Self-Adhering Millennium One Step Foamable Adhesive,12-inch D.C. -157.5
VB-5. PG100 Elastoflex SA P Self-Adhering CR-20,12-inch D.C. -270.0
VB-6. PG100 Elastoflex SA V Base,Elastoflex SA V FR Base, Self-Adhering Millennium One Step Foamable Adhesive,Millennium PG-1 Pump Grade -290.0
Elastoflex SA V Plus,Elastoflex SA V Plus FIR Adhesive,OlyBond 500 or CR-20,12-inch D.C.
19. "MDP"=Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads.Refer to FBC 1609 for determination of design wind loads.
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 4 of 58
QO
TRINITY ERD
l
TABLE 1A: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) t
No. (Note 1) Type Attach Type Attach BasePly Ply Cap Ply
SELF-ADHERING BASE PLY:
Min.1.5-inch Polytherm,ACFoam II,Polytherm G,
Min.15/32- D-IS,M-OSFA, (Optional)additional D-IS,M-OSFA, (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
W 1 inch plywood ACFoam III,ENRGY-3,Polytherm H,H-Shield,H- OB500 or CR-20 layers(s)of base insulation OB500 or CR-20 SBS-SA APP-TA SBS-TA,APP-TA -52.5
Shield CG,Multi-Max FA3
Min.1.5-inch Polytherm,ACFoam II,Polytherm G,
W 2 Min.15/32- ACFoam III,ENRGY-3,Polytherm H,H-Shield,H- OB500
0 or CR-, (Optional)additional OB500
0 or CR-, BasePoly ex SA (Optional)APP-TA APP-TA -52.5
inch plywood Shield CG,Multi-Max FA3 OB500 or CR-20 layers(s)of base insulation OB500 or CR-20 Base
TABLE 113-1: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15)
System Deck MDP
No. (Note 1) Type Fasten Attach Type Attach Type Attach BPly Ply Cap Ply (psf)
ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY:
9-inch o.c.at 2-inch (Optional)Min.1.5-inch Min.0.75-inch Fesco
Min. Elastobase, Simplex MAXX Hot lap and 18-inch o.c. Polytherm,ACFoam II, Board(homogeneous)or BP-AA (Optional) SBS-AA,
W-3 15/32-inch Elastobase P Cap in two(2),equally ENRGY-3,Polytherm H, Hot asphalt min.0.5-inch Structodek asphalt or SBS- BP-AA or SBS-TA, -45.0*
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, High Density Fiberboard AA SBS-AA APP-TA
center rows Multi-Max FA3 Roof Insulation
9-inch o.c.at 2-inch (Optional)Min.1.5-inch Min.0.25-inch Dens BP-AA, (Optional)
Min. Elastobase, lap and 18-inch o.c. Polytherm,ACFoam II, SBS-AA,
Simplex MAXX Deck,Dens Deck Prime, Hot SBS-AA, BP-AA,SBS-
W-4 15/32-inch Elastobase P Cap in two(2),equally ENRGY-3,Polytherm H, Hot asphalt SECU ROCK Gypsum-Fiber asphalt SBS-TA, AA,SBS-TA, SBS-TA, -45.0*
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, APP-TA
center rows Multi-Max FA3 Roof Board APP-TA APP-TA
9-inch D.C.at 2-inch (Optional)Min.1.5-inch Min.0.75-inch Fesco
Min. Elastobase, Simplex MAXX Hot lap and 12-inch o.c. Polytherm,ACFoam II, Board(homogeneous)or BP-AA (Optional) SBS-AA,
W-5 15/32-inch Elastobase P in two(2),equally ENRGY-3,Polytherm H, Hot asphalt min.0.5-inch Structodek or SBS- BP-AA or SBS-TA, -52.5
plywood (sanded-top) Cap spaced,staggered H-Shield,H-Shield CG, High Density Fiberboard asphalt AA SBS-AA APP-TA
center rows Multi-Max FA3 Roof Insulation
9-inch D.C.at 2-inch (Optional)Min.1.5-inch Min.0.25-inch Dens BP-AA, (Optional)
Min. Elastobase, lap and 12-inch o.c. Polytherm,ACFoam II, SBS-AA,
Simplex MAXX Deck,Dens Deck Prime, Hot SBS-AA, BP-AA,SBS-
W-6 15/32-inch Elastobase P Cap in two(2),equally ENRGY-3,Polytherm H, Hot asphalt SECUROCK Gypsum-Fiber asphalt SBS-TA, AA,SBS-TA, SBS-TA, -52.5
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, Roof Board APP-TA APP-TA APP TA
center rows Multi-Max FA3
Exterior Research and Design,I.I.C.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 5 of 58
QO
TRINITY ERD
TABLE 16-1: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15)
System Deck MDP
No. (Note 1) Type Fasten Attach Type Attach Type Attach BPly Ply Cap Ply (PS9
Polyglass G2 Base,
Elastobase, (Optional)Min.1.5-inch
Elastobase P 32 ga.,1-5/8- 8-inch o.c.in 4-inch Min.0.75-inch Fesco
Polytherm,ACFoam II,
Min. (sanded-top), inch diameter lap and 8-inch o.c.in Polytherm G,ACFoam Hot Board(homogeneous)or BP-AA (Optional) SBS-AA,
W-7 19/32-inch CertainTeed tin caps with three(3),equally Hot asphalt min.0.5-inch Structodek or SBS- BP-AA or SBS-TA, -60.0
plywood Glasbase,Firestone 11 ga.annular spaced,staggered III,ENRGY-3,Polytherm High Density Fiberboard asphalt AA SBS-AA APP-TA
MB Base,JM Perma- ring shank nails center rows H,H-Shield,H-Shield Roof Insulation
Ply 28,Tamko Glass CG,Multi-Max FA3
Base or GAFGLAS#75
Polyglass G2 Base,
Elastobase, (Optional)Min.1.5-inch
Elastobase P 32 ga.,1-5/8- 8-inch o.c.in 4-inch Polytherm,ACFoam II, BP-AA, (Optional)
Min. (sanded-top), inch diameter lap and 8-inch o.c.i Polytherm G,ACFoam Hot SBS-AA, BP-AA,SBS-
n Min.0.25-inch Dens Deck SBS-AA,
III ENRGY-3,Polytherm asphalt SBS-TA, AA,SBS-TA,
W-8 19/32-inch CertainTeed tin caps with three(3),equally Hot asphalt Prime,SECUROCK SBS-TA, -60.0
,
plywood Glasbase,Firestone 11 ga.annular spaced,staggered Gypsum-Fiber Roof Board APP-TA
MB Base,JM Perma- ring shank nails center rows H,H-Shield,H-Shield APP-TA APP-TA
Ply 28,Tamko Glass CG,Multi-Max FA3
Base or GAFGLAS#75
12-inch o.c.in 4-inch (Optional)Min.1.5-inch Min.0.75-inch Fesco
Min. Elastobase, Simplex MAXX Hot lap and 12-inch o.c. Polytherm,ACFoam II, Board(homogeneous)or BP-AA (Optional) SBS-AA,
W-9 19/32-inch Elastobase P Cap Fasteners in two(2),equally ENRGY-3,Polytherm H, Hot asphalt min.0.5-inch Structodek asphalt or SBS- BP-AA or SBS-TA, -60.0
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, High Density Fiberboard AA SBS-AA APP-TA
center rows Multi-Max FA3 Roof Insulation
12-inch o.c.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens BP-AA, (Optional)
Min. Elastobase, lap and 12-inch o.c. Polytherm,ACFoam II, SBS-AA,
Simplex MAXX Deck,Dens Deck Prime, Hot SBS-AA, BP-AA,SBS-
W-10 19/32-inch Elastobase P Cap Fasteners in two(2),equally ENRGY-3,Polytherm H, Hot asphalt SECUROCK Gypsum-Fiber asphalt SBS-TA, AA,SBS-TA, SBS-TA, -60.0
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, Roof Board APP-TA APP-TA APP TA
center rows Multi-Max FA3
32 ga.,1-5/8- 8-inch o.c.in 4-inch (Optional)Min.1.5-inch BP-AA, (Optional)
Min. Elastobase, inch diameter lap and 8-inch o.c.in Polytherm,ACFoam II, Min.0.25-inch Dens Deck SBS-AA,
Hot SBS-AA, BP-AA,SBS-
W-11 15/32-inch Elastobase P tin caps with four(4),equally ENRGY-3,Polytherm H, Hot asphalt Prime,SECUROCK SBS-TA, -67.5
plywood (sanded-top) 12 ga.annular spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof Board asphalt SBS-TA, AA,SBS-TA, APP-TA
ring shank nails center rows Multi-Max FA3 APP-TA APP-TA
9-inch o.c.in 4-inch (Optional)Min.1.5-inch BP-AA, (Optional)
Min. lap and 9-inch o.c.in Polytherm,ACFoam II, Min.0.25-inch Dens Deck SBS-AA,
Simplex MAXX Hot SBS-AA, BP-AA,SBS-
W-12 15/32-inch Polyglass G2 Base Cap asphalt SBS-TA, AA,SBS-TA,four(4),equally ENRGY-3,Polytherm H, Hot asphalt Prime,SECUROCK SBS-TA, -82.5
plywood spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof Board APP-TA
center rows Multi-Max FA3 APP-TA APP-TA
32 ga.,1-5/8- 6-inch o.c.in 4-inch (Optional)Min.1.5-inch
Polyglass G2 Base, BP-AA, (Optional)
Min. Elastobase P inch diameter lap and 6-inch o.c.in Polytherm,ACFoam II, Min.0.25-inch Dens Deck SBS-AA,
Elastobase, Hot SBS-AA, BP-AA,SBS-
W-13 15/32-inch tin caps with five(5)equally ENRGY-3,Polytherm H, Hot asphalt Prime,SECUROCK SBS-TA, -90.0
plywood 12 ga.annular spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof Board asphalt SBS-TA, AA,SBS-TA, APP TA
(sanded-top) ring shank nails center rows Multi-Max FA3 APP-TA APP-TA
Exterior Research and Design,I.I.C.d/b/a Trinity)ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 6 of 58
QO
TRINITY ERD
TABLE 16-1: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15)
System Deck MDP
No. (Note 1) Type Fasten Attach Type Attach Type Attach BPly Ply Cap Ply (PS9
6-inch o.c.at 2-inch (Optional)Min.1.5-inch BP-AA, (Optional)
Simplex MAXX Hot SBS-AA, BP-AA,SBS-
Min. Elastobase, lap and 6-inch o.c.in Polytherm,ACFoam II, Min.0.25-inch Dens Deck SBS-AA,
W-14 15/32-inch Elastobase P two(2),equally ENRGY-3,Polytherm H, Hot asphalt Prime,SECUROCK SBS-TA, -90.0
plywood (sanded-top) Cap spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof Board asphalt SBS-TA, AA,SBS-TA, APP-TA
center rows Multi-Max FA3 APP-TA APP-TA
32 ga.,1-5/8- 6-inch o.c.in 4-inch Min.2-inch Polytherm, D-IS,OB500, Min.0.25-inch Dens D-IS, BP-AA, (Optional)
Min. Elastobase, inch diameter lap and 6-inch o.c.in ACFoam II,III, CR-20 or M- SBS-AA,
W-15 19/32-inch Elastobase P tin caps with four(4),equally Polytherm H,H-Shield, OSFA,atop Deck,Dens Deck Prime or CR-2OB5 0, SBS-AA, BP-AA,SBS- SBS-TA, -60.0*
plywood (sanded-top) 12 ga.annular spaced,staggered H-Shield CG,Multi-Max fastener rows, Roof
Boar Gypsum-Fiber M-OS or SBS-TA, AA,SBS-TA, APP TA
ring shank nails center rows FA3 or ENRGY-3 7-inch o.c. Roof Board M-OSFA APP-TA APP-TA
SELF-ADHERING BASE PLY:
9-inch o.c.at 2-inch (Optional)Min.1.5-inch Min.0.25-inch Dens SBS-SA,
Min. Elastobase, (Optional)lap and 18-inch o.c. Polytherm,ACFoam II,
Simplex MAXX Deck,Dens Deck Prime, Hot APP-SA,
W-16 15/32-inch Elastobase P in two,equally ENRGY-3,Polytherm H, Hot asphalt SBS-SA SBS-SA,SBS- -45.0*
Roof B
plywood (sanded-top) Cap spaced,staggered H-Shield,H-Shield CG, o APP-TA Board SECUROCK Gypsum-Fiber asphalt TA,APP-TA SBS-TA,
center rows Multi-Max FA3 Roof Bo
9-inch o.c.at 2-inch (Optional)Min.1.5-inch
Min. Elastobase, lap and 18-inch o.c. Polytherm,ACFoam II, Min. Dens
Dens
Simplex MAXX Deck,Dens Deck Prime, Hot Polyflex (Optional)
W-17 15/32-inch Elastobase P Cap in two,equally ENRGY-3,Polytherm H, Hot asphalt SECUROCK Gypsum-Fiber asphalt SA Base APP-TA APP-TA -45.0*
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, Roof Board
center rows Multi-Max FA3
9-inch o.c.at 2-inch (Optional)Min.1.5-inch Min.0.25-inch Dens SBS-SA,
Min. Elastobase, lap and 12-inch o.c. Polytherm,ACFoam II, (Optional)
Simplex MAXX Deck,Dens Deck Prime, Hot APP-SA,
W-18 15/32-inch Elastobase P in two,equally ENRGY-3,Polytherm H, Hot asphalt SBS-SA SBS-SA,SBS- -52.5
Cap RoofSECL Boa ROCK Gypsum-Fiber asphalt SBS-TA,
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, Roof Board TA'APP TA APP-TA
center rows Multi-Max FA3
9-inch o.c.at 2-inch (Optional)Min.1.5-inch Min.0.25-inch Dens
Min. Elastobase, lap and 12-inch o.c. Polytherm,ACFoam II,
Simplex MAXX Deck,Dens Deck Prime, Hot Polyflex (Optional)
W-19 15/32-inch Elastobase P Cap in two,equally ENRGY-3,Polytherm H, Hot asphalt SECUROCK Gypsum-Fiber asphalt SA Base APP-TA APP-TA -52.5
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, Roof Board
center rows Multi-Max FA3
Polyglass G2 Base,
Elastobase, (Optional)Min.1.5-inch
Elastobase P 32 ga.,1-5/8- 8-inch o.c.in 4-inch Polytherm,ACFoam II, Min.0.25-inch Dens SBS-SA,
Min. (sanded-top), inch diameter lap and 8-inch o.c.in (Optional)
Polytherm G,ACFoam Deck,Dens Deck Prime, Hot APP-SA,
III,ENRGY-3,Polytherm SECUROCK Gypsum-Fiber asphalt SBS-TA,
W-20 19/32-inch CertainTeed tin caps with three(3),equally Hot asphalt SBS-SA SBS-SA,SBS- -60.0
plywood Glasbase,Firestone 11 ga.annular spaced,staggered TA,APP-TA
MB Base,JM Perma- ring shank nails center rows H,H-Shield,H-Shield Roof Board APP-TA
Ply 28,Tamko Glass CG,Multi-Max FA3
Base or GAFGLAS#75
Exterior Research and Design,LLC.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 7 of 58
QO
TRINITY ERD
TABLE 16-1: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15)
System Deck MDP
No. (Note 1) Type Fasten Attach Type Attach Type Attach BPly Ply Cap Ply (PS9
Polyglass G2 Base,
Elastobase, (Optional)Min.1.5-inch
Elastobase P 32 ga.,1-5/8- 8-inch o.c.in 4-inch Polytherm,ACFoam II, Min.0.25-inch Dens
Min. (sanded-top), inch diameter lap and 8-inch o.c.in Polytherm G,ACFoam Deck,Dens Deck Prime, Hot Polyflex (Optional)
W-21 19/32-inch CertainTeed tin caps with three(3),equally Hot asphalt APP-TA -60.0
plywood Glasbase,Firestone 11 ga.annular spaced,staggered III,ENRGY-3,Polytherm SECUROCK Gypsum-Fiber asphalt SA Base APP-TA
MB Base,JM Perma- ring shank nails center rows H,H-Shield,H-Shield Roof Board
Ply 28,Tamko Glass CG,Multi-Max FA3
Base or GAFGLAS#75
12-inch o.c.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens SBS-SA,
Min. Elastobase, lap and 12-inch o.c. Polytherm,ACFoam II, (Optional)
Simplex MAXX Deck,Dens Deck Prime, Hot APP-SA,
W-22 19/32-inch Elastobase P Cap Fasteners in two(2),equally ENRGY-3,Polytherm H, Hot asphalt SECUROCK Gypsum-Fiber asphalt SBS-SA SBS-SA,SBS- SBS-TA, -60.0
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, Roof Board TA,APP-TA APP-TA
center rows Multi-Max FA3
12-inch o.c.in 4-inch (Optional)Min.1.5-inch
Min. Elastobase, lap and 12-inch o.c. Polytherm,ACFoam II, Min. Dens
Dens
Simplex MAXX Deck,Dens Deck Prime, Hot Polyflex (Optional)
W-23 19/32-inch Elastobase P Cap Fasteners in two(2),equally ENRGY-3,Polytherm H, Hot asphalt SECUROCK Gypsum-Fiber asphalt SA Base APP-TA APP-TA -60.0
plywood (sanded-top) spaced,staggered H-Shield,H-Shield CG, Roof Board
center rows Multi-Max FA3
Polyglass G2 Base, 32 ga.,1-5/8- 8-inch o.c.in 4-inch (Optional)Min.1.5-inch
Min. inch diameter lap and 8-inch o.c.in Polytherm,ACFoam II, Min.0.25-inch Dens Deck
Elastobase, Hot Polyflex (Optional)
W-24 15/32-inch Elastobase P tin caps with four(4),equally ENRGY-3,Polytherm H, Hot asphalt Prime,SECUROCK APP-TA -67.5
plywood 12 ga.annular spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof Board asphalt SA Base APP-TA
(sanded-top) ring shank nails center rows Multi-Max FA3
9-inch o.c.in 4-inch (Optional)Min.1.5-inch
Min. lap and 9-inch o.c.in Polytherm,ACFoam II, Min.0.25-inch Dens Deck
Simplex MAXX Hot Polyflex (Optional)
W-25 15/32-inch Polyglass G2 Base Cap asphalt SA Base APP-TA
four(4),equally ENRGY-3,Polytherm H, Hot asphalt Prime,SECUROCK APP-TA -82.5
plywood spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof Board
center rows Multi-Max FA3
Polyglass G2 Base, 32 ga.,1-5/8- 6-inch o.c.in 4-inch (Optional)Min.1.5-inch
Min. inch diameter lap and 6-inch o.c.in Polytherm,ACFoam II, Min.0.25-inch Dens Deck
Elastobase, Hot Polyflex (Optional)
W-26 15/32-inch Elastobase P asphalt SA Base APP-TA tin caps with five(5)equally ENRGY-3,Polytherm H, Hot asphalt Prime,SECUROCK APP-TA -90.0
plywood (sanded-top) 12 ga.annular spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof Board
ring shank nails center rows Multi-Max FA3
6-inch o.c.at 2-inch (Optional)Min.1.5-inch
Min. Elastobase, lap and 6-inch o.c.in Polytherm,ACFoam II, Min.0.25-inch Dens Deck
Simplex MAXX Hot Polyflex (Optional)
W-27 15/32-inch Elastobase P two(2),equally ENRGY-3,Polytherm H, Hot asphalt Prime,SECUROCK APP-TA -90.0
plywood (sanded-top) Cap spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof Board asphalt SA Base APP-TA
center rows Multi-Max FA3
Exterior Research and Design,LLC.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 8 of 58
QO
TRINITY ERD
TABLE 16-1: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15)
System Deck MDP
No. (Note 1) Type Fasten Attach Type Attach Type Attach BPly Ply Cap Ply (psf)
32 ga.,1-5/8- 6-inch o.c.in 4-inch Min.2-inch Polytherm, D-IS,OB500, D-IS, SBS-SA,
Min. Elastobase, inch diameter lap and 6-inch o.c.in ACFoam II,III, CR-20 or M- (Optional)
(Optional)Additional OB500, APP-SA,
or
W-28 19/32-inch Elastobase P tin caps with four(4),equally Polytherm H,H-Shield, OSFA,atop SBS-SA SBS-SA,SBS- -60.0*
M-OS
plywood (sanded-top) 12 ga.annular spaced,staggered H-Shield CG,Multi-Max fastener rows, layers of base insulation TA APP TA SBS-TA,
ring shank nails center rows FA3 or ENRGY-3 7-inch o.c. -OSFA APP-TA
32 ga.,1-5/8- 6-inch o.c.in 4-inch Min.2-inch Polytherm, D-IS,OB500, D-IS,
Min. Elastobase, inch diameter lap and 6-inch o.c.in ACFoam II,III, CR-20 or M- (Optional)Additional OB500, Polyflex (Optional)
W-29 19/32-inch Elastobase P tin caps with four(4),equally Polytherm H,H-Shield, OSFA,atop APP-TA -60.0*
M-OS
plywood (sanded-top) 12 ga.annular spaced,staggered H-Shield CG,Multi-Max fastener rows, layers of base insulation or SA Base APP-TA
ring shank nails center rows FA3 or ENRGY-3 7-inch o.c. -OSFA
Exterior Research and Design,LLC.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 9 of 58
Q0TFmNrry'ERD
TABLE 1B-2: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
System Deck Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15) MDP
No. (Note 1) Type Fasten Attach Type Attach Type Attach Base Ply Ply Cap Ply (PS9
ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY:
Dekfast Hex(aka,Dekfast
PLT-H-2-7/8)with Dekfast
Polyglass G2 10-inch D.C.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens
#14,OMG 3"Round Metal BP-AA, (Optional)
Min.15/32- Base .c. Polytherm,ACFoam II, Deck,Dens Deck SBS-AA,
Plate with OMG HD,OMG Hot Hot SBS-AA, BP-AA,SBS-
W-30 inch Elastobase, in three(3),equally ENRGY-3,Polytherm H, Prime,SECUROCK SBS-TA, 52.5
Flat Bottom Plate(Accutrac) asphalt asphalt SBS-TA, AA,SBS-TA,
plywood Elastobase P with Roofgrip#14 or Trufast spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof APP-TA APP-TA APP-TA
(sanded-top) 3"Metal Insulation Plate center rows Multi-Max FA3 Board
with Trufast HD.
12-inch D.C.in 4-inch (Optional)Min.1.5-inch Min.0.75-inch FescoBoard(homogeneous)
Min.19/32- Elastobase, lap and 12-inch D.C. Polytherm,ACFoam ll, (Optional) SBS-AA,
OMG Flat Bottom Plates Hot or min.0.5-inch Hot BP-AA or
W-31 inch Elastobase P in two(2),equally ENRGY-3,Polytherm H, BP-AA or SBS-TA, -60.0
plywood (sanded-top) (square)with Roofgrip#12 spaced,staggered H-Shield,H-Shield CG, asphalt Structodek High asphalt SBS-AA SBS-AA APP-TA
center rows Multi-Max FA3 Density Fiberboard
Roof Insulation
12-inch D.C.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens BP-AA (Optional)
Min.19/32- Elastobase, OMG Flat Bottom Plates Hot Hot SBS-AA, BP-AA,SBS-
lap and 12-inch D.C. Polytherm,ACFoam ll, Deck,Dens Deck SBS-AA,
W-32 inch Elastobase P in two(2),equally ENRGY-3,Polytherm H, Prime,SECUROCK SBS-TA, -60.0
plywood (sanded-top) (square)with Roofgrip#12 spaced,staggered H-Shield,H-Shield CG, asphalt Gypsum-Fiber Roof asphalt SBS-TA, AA,SBS-TA, APP-TA
center rows Multi-Max FA3 Board APP-TA APP-TA
Dekfast Hex(aka,Dekfast
PLT-H-2-7/8)with Dekfast
Polyglass G2 9-inch D.C.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens
#14,OMG 3"Round Metal BP-AA (Optional)
Min.15/32- Base, lap and 9-inch D.C.o.c.in Polytherm,ACFoam II, Deck,Dens Deck S65-AA,
Plate with OMG HD,OMG Hot Hot SBS-AA, BP-AA,SBS-
W-33 inch Elastobase, four(4),equally ENRGY-3,Polytherm H, Prime,SECUROCK S65-TA, 82.5
Flat Bottom Plate(Accutrac) asphalt asphalt SBS-TA, AA,SBS-TA,
plywood Elastobase P with Roofgrip#14 or Trufast spaced,staggered H-Shield,H-Shield CG, Gypsum-Fiber Roof APP-TA APP-TA APP-TA
(sanded-top) 3"Metal Insulation Plate center rows Multi-Max FA3 Board
with Trufast HD.
SELF-ADHERING BASE PLY:
Dekfast Hex(aka,Dekfast
Polyglass G2 PLT-H-2-7/8)with Dekfast 10-inch D.C.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens
#14,OMG 3"Round Metal
Min.15/32- Base, lap and 10-inch D.C. Polytherm,ACFoam II, Deck,Dens Deck
Plate with OMG HD,OMG Hot Hot Polyflex SA (Optional)
W-34 inch Elastobase, in three(3),equally ENRGY-3,Polytherm H, Prime,SECUROCK APP-TA 52.5
plywood Elastobase P Flat Bottom Plate(Accutrac) spaced,staggered H-Shield,H-Shield CG, asphalt Gypsum-Fiber Roof
3"Metal Insulation Platelate asphalt Base APP-TA
(sanded-top) with Roofgrip#14 Or t center rows Multi-Max FA3 Board
with Trufast HD.
12-inch D.C.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens SBS-SA,
Min.19/32- Elastobase, lap and 12-inch O.C. Polytherm,ACFoam II, Deck,Dens Deck (Optional)
OMG Flat Bottom Plates Hot Hot APP-SA,
W-35 inch Elastobase P in two(2),equally ENRGY-3,Polytherm H, Prime,SECUROCK SBS-SA SBS-SA,SBS- -60.0
plywood (sanded-top) (square)with Roofgrip#12 spaced,staggered H-Shield,H-Shield CG, asphalt Gypsum-Fiber Roof asphalt TA APP TA SBS-TA,
APP-TA
center rows Multi-Max FA3 Board
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6TR EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 10 of 58
QO
TRINITY ERD
TABLE 113-2: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
System Deck Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15) MDP
No. (Note 1) Type Fasten Attach Type Attach Type Attach Base Ply Ply Cap Ply (PS9
12-inch D.C.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens
Min.19/32- Elastobase, lap and 12-inch D.C. Polytherm,ACFoam II, Deck,Dens Deck
OMG Flat Bottom Plates Hot Hot Polyflex SA (Optional)
W-36 inch Elastobase P in two(2),equally ENRGY-3,Polytherm H, Prime,SECUROCK APP-TA -60.0
plywood (sanded-top) (square)with Roofgrip#12 spaced,staggered H-Shield,H-Shield CG, asphalt Gypsum-Fiber Roof asphalt Base APP-TA
center rows Multi-Max FA3 Board
Dekfast Hex(aka,Dekfast
Polyglass G2 PLT-H-2-7/8)with Dekfast 9-inch D.C.in 4-inch (Optional)Min.1.5-inch Min.0.25-inch Dens
#14,OMG 3"Round Metal
Min.15/32- Base, lap and 9-inch D.C.in Polytherm,ACFoam II, Deck,Dens Deck
Plate with OMG HD,OMG Hot Hot Polyflex SA (Optional)
W-37 inch Elastobase, four(4),equally ENRGY-3,Polytherm H, Prime,SECUROCK APP-TA -82.5
plywood Elastobase P Flat Bottom Plate(Accutrac) spaced,staggered H-Shield,H-Shield CG, asphalt Gypsum-Fiber Roof asphalt Base APP-TA
(sanded-top) with Roofgrip#14 or Trufast center rows Multi-Max FA3 Board
3"Metal Insulation Plate
with Trufast HD.
TABLE 1C: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE B: MECHANICALLY ATTACHED BASE INSULATION,BONDED TOP INSULATION,BONDED ROOF COVER
System Deck(Note 1) Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MOP
No. Type Fasten Attach Type Attach Base Ply Ply Cap Ply (Psf)
ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY:
Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.75-inch Fesco Board
Min.1.5-inch ENRGY (Optional if (Optional if using AA SBS-AA,
Min.19/32- 7/8)with Dekfast#12 or Trufast 3" 1 per (homogeneous)or min.0.5-inch Hot
W-38 3,H-Shield or z using AA Ply) Base)BP-AA,SBS-AA, 565-TA, -60.0
inch plywood Polytherm Metal Insulation Plate with Trufast 1.33 ft Structodek High Density Fiberboard asphalt BP-AA,SBS-AA SBS-TA or APP-TA APP-TA
DP Roof Insulation
Min.2-inch Polytherm, Dekfast#14 with Dekfast Hex(aka,
ACFoam II,ENRGY-3, Dekfast PLT-H-2-7/8),OMG#14 HD SBS-AA,
Min.15/32- 1 per 1 Min.0.25-inch Dens Deck Prime or Hot SBS-AA,SBS- (Optional)5B5-AA,
W-39 inch plywood EnergyGuard Polyiso with OMG 3"Galvalume Steel Plates ftz SECUROCK Gypsum Fiber Roof Board asphalt TA,APP-TA SBS-TA,APP-TA SBS-TA, -75.0
Insulation,H-Shield or or Trufast HD with Trufast 3-inch APP-TA
Multi-Max FA3 Insulation Plates
SELF-ADHERING BASE PLY:
Min.2-inch Polytherm, Dekfast#14 with Dekfast Hex(aka,
ACFoam II,ENRGY-3, Dekfast PLT-H-2-7/8),OMG#14 HD
Min.15/32- 1 per 1 Min.0.25-inch Dens Deck Prime or Hot Polyflex SA
W-40 inch plywood EnergyGuard Polyiso with OMG 3"Galvalume Steel Plates ftz SECUROCK Gypsum Fiber Roof Board asphalt Base (Optional)APP-TA APP-TA -75.0
Insulation,H-Shield or or Trufast HD with Trufast 3-inch
Multi-Max FA3 Insulation Plates
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6TH EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 11 of 58
QOTRINI-FY 'ERD
TABLE 1D: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER
System Top Insulation Layer Roof Cover(Note 15) MDP
No. Deck(Note 1) Base Insulation Layer Type Fasten Attach Base Ply Ply Cap Ply (PSq
ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY:
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with
(Optional)One or more Dekfast#14,OMG 3"Round Metal Plate with BP-AA,SBS- (Optional)BP-
W 41 Min.15/32- layers,any combination, Min. inch Dens Deck Prime or OMG HD,OMG Flat Bottom Plate(Accutrac)with 1 per 2 ftz AA,SBS-TA, AA,SBS-AA,SBS- SBS-AA,SBS-
SECURROCOC -30.0
inch plywood loose laid K Gypsum-Fiber Roof Board Roofgrip#14 or Trufast 3"Metal Insulation Plate APP-TA TA,APP-TA TA,APP-TA
with Trufast HD.
Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-
(Optional)One or more (Optional)SBS-
Min.15/32- Min.0.25-inch Dens Deck Prime or 2-7/8),OMG#14 HD with OMG 3"Galvalume Steel 1 per 1.78 SBS-AA,SBS- SBS-AA,SBS-
W 42 inch plywood layers,any combination, SECUROCK Gypsum-Fiber Roof Board Plates or Trufast HD with Trufast 3-inch Insulation ftz TA,APP-TA AA,SBS-TA,APP- TA APP TA -45.0
loose laid Plates TA
(Optional)One or more
Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-
(Optional)SBS-
Min.15/32- Min.0.25-inch Dens Deck Prime or 2-7/8),OMG#14 HD with OMG 3"Galvalume Steel Z SBS-AA,SBS- SBS-AA,SBS-
W 43 inch plywood layers,any combination, SECUROCK Gypsum-Fiber Roof Board Plates or Trufast HD with Trufast 3-inch Insulation 1 per 1 ft TA,APP-TA SBS-TA,APP- TA APP TA 75.0
loose laid Plates TA
Min.0.5-inch Structodek High (Optional if (Optional if using
(Optional)One or more Density Fiberboard Roof Insulation or
Min.19/32- Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with 1 per 1.33 using AA Ply) AA Base)BP-AA, SBS-AA,SBS-
W 44 inch plywood layers,any combination, min.0.25-inch Dens Deck,Dens Deck Dekfast#12 DP ftZ BP-AA,SBS- SBS-AA,SBS-TA TA,APP-TA 82.5
loose laid Prime or SECUROCK Gypsum-Fiber
AA or APP-TA
Roof Board
SELF-ADHERING BASE PLY:
Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-
(Optional)One or more (Optional)SBS- SBS-SA,APP-
Min.15/32- Min.1.5-inch Polytherm,ACFoam II, 2-7/8),OMG#14 HD with OMG 3"Galvalume Steel 1 per 2.67
W-45 layers,any combination, z SBS-SA SA,SBS-TA,APP- SA,SBS-TA, -30.0
inch plywood loose laid H-Shield or Polytherm Plates or Trufast HD with Trufast 3-inch Insulation ft TA APP-TA
Plates
(Optional)One or more Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-
Min.15/32- Min.1.5-inch Polytherm,ACFoam ll, 2-7/8),OMG#14 HD with OMG 3"Galvalume Steel 1 per 2.67 Polyflex SA (Optional)APP-
W-46 inch plywood layers,any combination, H-Shield or Polytherm Plates or Trufast HD with Trufast 3-inch Insulation ftZ Base TA APP-TA -30.0
loose laid
Plates
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with
25-inch Dens Deck Prime or 0 Min.15/32- .
(Optional)One or more Min. Dekfast#14,OMG 3"Round Metal Plate with (Optional)SBS- SBS-SA,APP-
W-47 layers,any combination, OMG HD,OMG Flat Bottom Plate(Accutrac)with 1 per 2 ftZ SBS-SA SA,SBS-TA,APP- SA,SBS-TA, -30.0
inch plywood loose laid SECUROCK Gypsum-Fiber Roof Board Roofgrip#14 or Trufast 3"Metal Insulation Plate TA APP-TA
with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with
(Optional)One or more Dekfast#14,OMG 3"Round Metal Plate with
W 48 Min.15/32- layers,any combination, Min. inch Dens Deck Prime or OMG HD,OMG Flat Bottom Plate(Accutrac)with 1 per 2 ftz Polyflex SA (Optional)APP-
SECURROCOC Base TA
APP-TA -30.0
inch plywood loose laid K Gypsum-Fiber Roof Board Roofgrip#14 or Trufast 3"Metal Insulation Plate
with Trufast HD.
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6TH EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 12 of 58
QO
TRINITY ERD
TABLE 1D: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER
System Top Insulation Layer Roof Cover(Note 15) MDP
No. Deck(Note 1) Base Insulation Layer Type Fasten Attach Base Ply Ply Cap Ply (psf)
Polygrip#14 with Polygrip Hex Plate or Dekfast
#14 with Dekfast Hex(aka,Dekfast PLT-H-2-7/8)or
(Optional for recover) Min.0.25-inch SECUROCK Gypsum-
Dekfast Galvalume Steel 3"Round(aka,Dekfast
Min.15/32- One or more layers,any PLT-R-3)or OMG#14 Roofgrip with OMG 3 in. Z
W 49 inch plywood combination,min.1- Fiber Roof Board optionally primed Round Metal Plate,OMG 3 in.Ribbed Galvalume 1 per 2 ft SBS-SA None SBS-SA 45.0
inch,loose laid with WB-3000 Plate(Flat)or Accutrac Flat Bottom Plate or
Trufast#14 HD Fasteners with Trufast 3"Metal
Insulation Plate
Polygrip#14 with Polygrip Hex Plate or Dekfast
(Optional for recover) #14 with Dekfast Hex(aka,Dekfast PLT-H-2-7/8)or
W-50 Min.15/32- One or more layers,any Min.0.25-inch Dens Deck Prime OMG#14 Roofgrip with OMG 3 in.Round Metal 1 per 2 ftZ SBS-SA None SBS-SA -45.0
inch plywood combination,min.1- optionally primed with WB-3000 Plate or Accutrac Flat Bottom Plate or Trufast#14
inch,loose laid HD Fasteners with Trufast 3"Metal Insulation
Plate
Polygrip#14 with Polygrip Hex Plate or Dekfast DF-
(Optional for recover) #14 with Dekfast Hex(aka,Dekfast PLT-H-2-7/8)or (Optional when
Min.0.25-inch SECUROCK Gypsum- SBS-SA,APP-
Min.15/32- One or more layers,any OMG#14 Roofgrip with OMG 3 in.Round Metal 1 per 1.78 using torch- -45.0
W-51 inch plywood combination,min.1- Fiber Roof Board optionally primed Plate or Accutrac Flat Bottom Plate or Trufast#14 ftZ SBS-SA applied Cap Ply) SA,SBS-TA or
inch,loose laid with WB-3000 HD Fasteners with Trufast 3"Metal Insulation SBS-TA,APP-TA APP-TA
Plate
(Optional for recover) (Optional when
OMG#14 Roofgrip with OMG 3 in.Round Metal SBS-SA,APP-
Min.15/32- One or more layers,any Min.0.25-inch Dens Deck Prime 1 per 1.78 using torch-
W-52 Plate or Trufast#14 HD Fasteners with Trufast 3" Z SBS-SA SA,SBS-TA or -45.0
inch plywood combination,min.1- optionally primed with WB-3000 Metal Insulation Plate ft applied Cap Ply) APP TA
inch,loose laid SBS-TA,APP-TA
(Optional)One or more Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-
Min.15/32- Min.0.25-inch Dens Deck Prime or 2-7/8),OMG#14 HD with OMG 3"Galvalume Steel 1 per 1.78 Polyflex SA (Optional)APP-
W-53 inch plywood layers,any combination, SECUROCK Gypsum-Fiber Roof Board Plates or Trufast HD with Trufast 3-inch Insulation ftZ Base TA APP-TA -45.0
loose laid
Plates
(Optional)One or more Min.0.25-inch Dens Deck Prime, Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-
Min.15/32- 2-7/8),OMG#14 HD with OMG 3"Galvalume Steel (Optional)SBS-
W-54 inch plywood layers,any combination, DEXcell FA Glass Mat Roof Board or Plates or Trufast HD with Trufast 3-inch Insulation 1 per 1 ft SBS-SA TA APP TA SBS-TA,APP-TA 60.0
loose laid SECUROCK Gypsum-Fiber Roof Board Plates
Min.19/32- (Optional)One or more Min.1.5-inch ENRGY 3,H-Shield or Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with 1 per 1.33 (Optional)SBS- SBS-SA,APP-
W-55 layers,any combination, Dekfast#12 DP or Trufast 3"Metal Insulation Plate Z SBS-SA SA,SBS-TA,APP- SA,SBS-TA, -82.5
inch plywood loose laid Polytherm with Trufast DP ft TA APP-TA
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 13 of 58
QO
TRINITY ERD
I
TABLE 1E: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPED:PRELIMINARILY ATTACHED INSULATION,MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
System Deck(Note 1) Insulation Layers) Base Sheet Roof Cover(Note 15) MDP
No. Type Attach Type Fasten Attach Base Ply Cap Ply (psf)
ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY:
Elastobase,Elastobase P, OMG Flat Bottom Plates(square)with
One or more Polyglass G2 Base,CertainTeed 12-inch o.c.in 4-inch lap and 12- (Optional)BP-AA,
Min.19/32- Prelim. Roofgrip#14,Dekfast Hex(aka,Dekfast PLT- SBS-AA,SBS-
W-56 layers,any Glasbase,Firestone MB Base, inch D.C.in two(2),equally spaced, SBS-AA,SBS-TA or -52.5
inch plywood combination Attached JM Perma-Ply 28,Tamko Glass Metal In with Dekfast wit#14h
or Trufast D staggered center rows APP-TA TA,APP-TA
Base or GAFGLAS#75 Metal Insulation Plate with Trufast HD
One or more Attached 12-inch o.c.in 4-inch lap and 12- (Optional)BP-AA,
Min.19/32- Prelim. OMG Flat Bottom Plates(square)with SBS-AA,SBS-
W-57 layers,any Elastobase or Elastobase P inch o.c.in two(2),equally spaced, SBS-AA,SBS-TA or -60.0
inch plywood combination Roofgrip#12 staggered center rows APP-TA TA,APP-TA
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with
One or more Dekfast#14,OMG 3"Round Metal Plate 10-inch o.c.in 4-inch lap and 10- (Optional)BP-AA,
Min.15/32- Prelim. Polyglass G2 Base,Elastobase, SBS-AA,SBS-
W-58 layers,any with OMG HD,OMG Flat Bottom Plate inch o.c.in three(3),equally SBS-AA,SBS-TA or -75.0
inch plywood combination Attached Elastobase P (Accutrac)with Roofgrip#14 or Trufast 3" spaced,staggered center rows APP-TA TA,APP-TA
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with
One or more Dekfast#14,OMG 3"Round Metal Plate 10-inch o.c.in 4-inch lap and 10-
W 59 Min.15/32- layers,any Prelim. Polyglass APP Base with OMG HD,OMG Flat Bottom Plate inch o.c.in three(3),equally (Optional)APP-TA APP-TA -75.0
inch plywood combination Attached (Accutrac)with Roofgrip#14 or Trufast 3" spaced,staggered center rows
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with
One or more Dekfast#14,OMG 3"Round Metal Plate 9-inch o.c.in 4-inch lap and 9-inch (Optional)BP-AA,
Min.15/32- Prelim. Polyglass G2 Base,Elastobase, SBS-AA,SBS-
W-60 layers,any with OMG HD,OMG Flat Bottom Plate o.c.in four(4),equally spaced, SBS-AA,SBS-TA or -90.0
inch plywood combination Attached Elastobase P (Accutrac)with Roofgrip#14 or Trufast 3" staggered center rows APP-TA TA,APP-TA
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with
Min.15/32-
One or more Prelim. Dekfast#14,OMG 3"Round Metal Plate 9-inch o.c.in 4-inch lap and 9-inch
W-61 layers,any Polyglass APP Base with OMG HD,OMG Flat Bottom Plate o.c.in four(4),equally spaced, (Optional)APP-TA APP-TA -90.0
inch plywood combination Attached (Accutrac)with Roofgrip#14 or Trufast 3" staggered center rows
Metal Insulation Plate with Trufast HD.
One or more 6-inch o.c.at 4-inch lap and 6-inch
Min.15/32- Prelim. Trufast#12 DP or Trufast#14 HD with (Optional)BP-AA
W 62 inch plywood layers,any Attached Elastobase,Elastobase P Trufast 3"Metal Insulation Plates o.c.in three(3),equally spaced, or SBS-AA SBS-AA -90.0
combination staggered center rows
One or more OMG#12 Standard Roofgrip or OMG#14 6-inch o.c.at 4-inch lap and 6-inch (Optional)BP-AA,
Min.15/32- Prelim. SBS-AA,SBS-
W-63 inch plywood layers,any Attached Elastobase,Elastobase P Heavy Duty with OMG 3"Round Metal o.c.in three(3),equally spaced, SBS-AA,SBS-TA, TA or APP-TA -90.0
combination Plates or OMG Flat Bottom Metal Plates staggered center rows APP-TA
Min.15/32-
One or more Prelim. OMG#12 Standard Roofgrip or OMG#14 6-inch o.c.at 4-inch lap and 6-inch
W-64 inch plywood layers,any Attached Polyglass APP Base Heavy Duty with OMG 3"Round Metal o.c.in three(3),equally spaced, (Optional)APP-TA APP-TA -90.0
combination Plates or OMG Flat Bottom Metal Plates staggered center rows
One or more 6-inch o.c.at 4-inch lap and 6-inch
Min.15/32- Prelim. Trufast#12 DP or Trufast#14 HD with (Optional)BP-AA
W-65 inch plywood layers,any Attached Elastobase,Elastobase P Trufast 3"Metal Insulation Plates o.c.in five(5),equally spaced, or SBS-AA SBS-AA -120.0
combination staggered center rows
Exterior Research and Design,LLC.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 14 of 58
QO
TRINITY ERD
TABLE 1E: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPED:PRELIMINARILY ATTACHED INSULATION,MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
System Deck(Note 1) Insulation Layer(s) Base Sheet Roof Cover(Note 15) MDP
No. Type Attach Type Fasten Attach Base Ply Cap Ply (psf)
One or more OMG#12 Standard Roofgrip or OMG#14 6-inch o.c.at 4-inch lap and 6-inch (Optional)BP-AA,
Min.15/32- Prelim. SBS-AA,SBS-
W-66 inch plywood layers,any Attached Elastobase,Elastobase P Heavy Duty with OMG 3"Round Metal o.c.in five(5),equally spaced, SBS-AA,SBS-TA, TA or APP-TA -120.0
combination Plates or OMG Flat Bottom Metal Plates staggered center rows APP-TA
Min.15/32-
One or more Prelim. OMG#12 Standard Roofgrip- OMG#14 6-inch o.c.at 4-inch lap and 6-inch
W 67 inch plywood layers,any Attached Polyglass APP Base Heavy Duty with OMG 3"Round Metal o.c.in five(5),equally spaced, (Optional)APP-TA APP-TA -120.0
combination Plates or OMG Flat Bottom Metal Plates staggered center rows
SELF-ADHERING BASE PLY:
Elastobase P(poly-Elastobase Min.19/32- ,
One or more Prelim. Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with 12-inch o.c.in 4-inch lap and 12- SBS-SA,APP-
W-68 layers,any Dekfast#14 or Trufast 3"Metal Insulation inch o.c.in two,equally spaced, SBS-SA SA,SBS-TA or -52.5*
inch plywood combination Attached film top) Plate with Trufast HD staggered center rows APP-TA
Min.19/32-
One or more Prelim. Elastobase,Elastobase P(poly- Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with 12-inch o.c.in 4-inch lap and 12-
W 69 inch plywood layers,any Attached film top) Dekfast#14 or Trufast 3"Metal Insulation inch o.c.in two,equally spaced, Polyflex SA Base APP-TA -52.5*
combination Plate with Trufast HD staggered center rows
One or more 12-inch o.c.in 4-inch lap and 12- SBS-SA,APP-
Min.19/32- Prelim. Elastobase,Elastobase P(poly- OMG Flat Bottom Plates(square)with
W-70 layers,any inch o.c.in two,equally spaced, SBS-SA SA,SBS-TA or -60.0*
inch plywood combination Attached film top) Roofgrip#12 staggered center rows APP-TA
One or more 12-inch o.c.in 4-inch lap and 12-
Min.19/32- Prelim. Elastobase,Elastobase P(poly- OMG Flat Bottom Plates(square)with
W 71 inch plywood layers,any Attached film top) Roofgrip#12 inch o.c.in two,equally spaced, Polyflex SA Base APP-TA -60.0*
combination staggered center rows
Exterior Research and Design,I.I.C.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 15 of 58
TRINITY I ERo
TABLE 1F-1: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE E: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(NAILS),BONDED ROOF COVER
System Deck(Note 1) Base Sheet Roof Cover(Note 15) MDP
No. Type Fasten Attach Base Ply Cap Ply (psf)
No BASE PLY:
W 72 Min.15/32- Elastobase,Elastobase P Simplex MAXX Cap 9-inch o.c.at 2-inch lap and 18-inch o.c.in two None SBS-AA,SBS-TA,APP- _45.0*
inch plywood (2),equally spaced,staggered center rows TA
W 73 Min.15/32- Elastobase,Elastobase P Simplex MAXX Cap 9-inch o.c.at 2-inch lap and 12-inch o.c.in two None SBS-AA,SBS-TA,APP- -52.5
inch plywood (2),equally spaced,staggered center rows TA
W 74 Min.15/32- Elastobase,Elastobase P Original Simplex Cap Nails(1-inch metal head diameter, 6-inch o.c.at 3-inch lap and 6-inch o.c.in four None SBS-AA,SBS-TA,APP- -52.5
inch plywood 11 gauge x min.1.25-inch long annular grooved shank) (4),equally spaced,staggered center rows TA
W 75 Min.15/32- Elastobase,Elastobase P(poly-film Original Simplex Cap Nails(1-inch metal head diameter, 6-inch o.c.at 3-inch lap and 6-inch o.c.in four None SBS-SA,APP-SA -52.5
inch plywood top) 11 gauge x min.1.25-inch long annular grooved shank) (4),equally spaced,staggered center rows
W 76 Min.15/32- Polyglass APP Base Original Simplex Cap Nails(1-inch metal head diameter, 6-inch o.c.at 3-inch lap and 6-inch o.c.in four None APP-TA -52.5
inch plywood 11 gauge x min.1.25-inch long annular grooved shank) (4),equally spaced,staggered center rows
Elastobase,Elastobase P,Polyglass
G2 Base,CertainTeed Glasbase,
Min.19/32- 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in three SBS-AA,SBS-TA,APP-
W 77 inch plywood Firestone MB Base,JM Perma-Ply ring shank nails (3),equally spaced,staggered center rows None TA -60.0
28,Tamko Glass Base or GAFGLAS
#75
W 78 Min.19/32- Elastobase,Elastobase P(poly-film 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in three None SBS-SA,APP-SA -60.0
inch plywood top) ring shank nails (3),equally spaced,staggered center rows
W 79 Min.15/32- Polyglass G2 Base,Elastobase, 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in four None SBS-AA,SBS-TA,APP- _67.5
inch plywood Elastobase P ring shank nails (4),equally spaced,staggered center rows TA
W 80 Min.15/32- Polyglass APP Base 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in four None APP-TA -67.5
inch plywood ring shank nails (4),equally spaced,staggered center rows
Min.15/32- Polyglass G2 Base,Elastobase, 10-inch o.c.in 4-inch lap and 10-inch o.c.in SBS-AA,SBS-TA,APP-
W 81 inch plywood Elastobase P Simplex MAXX Cap three(3),equally spaced,staggered center None TA -75.0
rows
Min.15/32- 10-inch o.c.in 4-inch lap and 10-inch o.c.in
W 82 inch plywood Polyglass APP Base Simplex MAXX Cap three(3),equally spaced,staggered center None APP-TA -75.0
rows
W 83 Min.15/32- Polyglass G2 Base,Elastobase, Simplex MAXX Cap 9-inch o.c.in 4-inch lap and 9-inch o.c.in four None SBS-AA,SBS-TA,APP- -90.0
inch plywood Elastobase P (4),equally spaced,staggered center rows TA
W 84 Min.15/32- Polyglass APP Base Simplex MAXX Cap 9-inch o.c.in 4-inch lap and 9-inch o.c.in four None APP-TA -90.0
inch plywood (4),equally spaced,staggered center rows
W 85 Min.15/32- Elastobase,Elastobase P Simplex MAXX Cap 6-inch o.c.at 2-inch lap and 6-inch o.c.in two None SBS-AA,SBS-TA,APP- -90.0
inch plywood (2),equally spaced,staggered center rows TA
W 86 Min.19/32- Elastobase,Elastobase P(poly-film 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 4-inch o.c.in 4-inch lap and 4-inch o.c.in four None SBS-SA,APP-SA -97.5
inch plywood top) ring shank nails. (4),equally spaced,staggered center rows
W 87 Min.15/32- Elastobase,Elastobase P Simplex MAXX Cap 6-inch o.c.at 2-inch lap and 6-inch o.c.in three None SBS-AA,SBS-TA,APP- 105.0
inch plywood (3),equally spaced,staggered center rows TA
Exterior Research and Design,LLC.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 16 of 58
QO
TRINITY ERD
TABLE 1F-1: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE E: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(NAILS),BONDED ROOF COVER
System Deck(Note 1) Base Sheet Roof Cover(Note 15) MDP
No. Type Fasten Attach Base Ply Cap Ply (psf)
Min.19/32- 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 6-inch o.c.in 4-inch lap and 6-inch o.c.in four None SBS-AA,SBS-TA,APP-
112.5 W 88 inch plywood Elastobase,Elastobase P ring shank nails (4),equally spaced,staggered center rows TA
32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular
W 89 Min.19/32- Elastobase,Elastobase P(poly-film ring shank nails. Note:Tin caps are to be primed with (-inch o.c.in 4-inch lap and 6-inch ceo.nter
r ows in four None SBS-SA,APP-SA -112.5
inch plywood top) PG100 orASTM D41 primer. (4),equally spaced,staggered center rows
ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY:
W 90 Min.15/32- Elastobase,Elastobase P Simplex MAXX Cap 9-inch o.c.at 2-inch lap and 18-inch o.c.in two BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS- _45.0*
inch plywood (2),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA
W 91 Min.15/32- Elastobase,Elastobase P Simplex MAXX Cap 9-inch o.c.at 2-inch lap and 12-inch o.c.in two BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS- -52.5
inch plywood (2),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA
W 92 Min.15/32- Elastobase,Elastobase P Original Simplex Cap Nails(1-inch metal head diameter, 6-inch o.c.at 3-inch lap and 6-inch o.c.in four BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS- -52.5
inch plywood 11 gauge x min.1.25-inch long annular grooved shank) (4),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA
W 93 Min.15/32- Polyglass APP Base Original Simplex Cap Nails(1-inch metal head diameter, 6-inch o.c.at 3-inch lap and 6-inch o.c.in four APP-TA APP-TA -52.5
inch plywood 11 gauge x min.1.25-inch long annular grooved shank) (4),equally spaced,staggered center rows
Elastobase,Elastobase P,Polyglass
G2 Base,CertainTeed Glasbase,
Min.19/32- 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in three BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS-
W 94 inch plywood Firestone MB Base,JM Perma-Ply ring shank nails (3),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA -60.0
28,Tamko Glass Base or GAFGLAS
#75
Min.15/32- Polyglass G2 Base,Elastobase, 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in four BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS-
W 95 inch plywood Elastobase P ring shank nails (4),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA 67.5
W-96 Min.15/32- Polyglass APP Base 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in four APP-TA APP-TA -67.5
inch plywood ring shank nails (4),equally spaced,staggered center rows
Min.15/32- Polyglass G2 Base,Elastobase, 10-inch o.c.in 4-inch lap and 10-inch o.c.in BP-AA SBS-AA,SBS- SBS-SA,APP-SA,SBS-
W 97 inch plywood Elastobase P Simplex MAXX Cap three(3),equally spaced,staggered center TA,APP-TA AA,SBS-TA,APP-TA -75.0
rows
Min.15/32- 10-inch o.c.in 4-inch lap and 10-inch o.c.in
W 98 inch plywood Polyglass APP Base Simplex MAXX Cap three(3),equally spaced,staggered center APP-TA APP-TA -75.0
rows
W 99 Min.15/32- Polyglass G2 Base,Elastobase, Simplex MAXX Cap 9-inch o.c.in 4-inch lap and 9-inch o.c.in four BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS- _90.0
inch plywood Elastobase P (4),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA
W-100 Min.15/32- Polyglass APP Base Simplex MAXX Cap 9-inch o.c.in 4-inch lap and 9-inch o.c.in four APP-TA APP-TA -90.0
inch plywood (4),equally spaced,staggered center rows
W-101 Min.15/32- Elastobase,Elastobase P Simplex MAXX Cap 6-inch o.c.at 2-inch lap and 6-inch o.c.in two BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS- _90.0
inch plywood (2),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA
W-102 Min.15/32- Elastobase,Elastobase P Simplex MAXX Cap 6-inch o.c.at 2-inch lap and 6-inch o.c.in three BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS- _105.0
inch plywood (3),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA
Min.19/32- 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 6-inch o.c.in 4-inch lap and 6-inch o.c.in four BP-AA,SBS-AA,5BS- SBS-SA,APP-SA,SBS-
inch plywood Elastobase,Elastobase P ring shank nails (3),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA 112.5
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 17 of 58
QO
TRINITY ERD
TABLE 1F-1: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE E: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(NAILS),BONDED ROOF COVER
System Deck(Note 1) Base Sheet Roof Cover(Note 15) MDP
No. Type Fasten Attach Base Ply Cap Ply (psf)
SELF-ADHERING BASE PLY:
W-104 Min.15/32- Elastobase,Elastobase P(poly-film Original Simplex Cap Nails(1-inch metal head diameter, 6-inch o.c.at 3-inch lap and 6-inch o.c.in four SBS-SA SBS-SA,APP-SA,SBS- -52.5
inch plywood top) 11 gauge x min.1.25-inch long annular grooved shank) (4),equally spaced,staggered center rows TA,APP-TA
W-105 Min.15/32- Polyglass APP Base,Elastobase, Original Simplex Cap Nails(1-inch metal head diameter, 6-inch o.c.at 3-inch lap and 6-inch o.c.in four Polyflex SA Base APP-TA -52.5
inch plywood Elastobase P(poly-film top) 11 gauge x min.1.25-inch long annular grooved shank) (4),equally spaced,staggered center rows
W-106 Min.19/32- Elastobase,Elastobase P(poly-film 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in three SBS-SA SBS-SA,APP-SA,SBS- -60.0
inch plywood top) ring shank nails (3),equally spaced,staggered center rows TA,APP-TA
W-107 Min.19/32- Elastobase,Elastobase P(poly-film 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 8-inch o.c.in 4-inch lap and 8-inch o.c.in three Polyflex SA Base APP-TA -60.0
inch plywood top) ring shank nails (3),equally spaced,staggered center rows
W-108 Min.19/32- Elastobase,Elastobase P(poly-film 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 4-inch o.c.in 4-inch lap and 4-inch o.c.in four SBS-SA SBS-SA,APP-SA,SBS- 97 5
inch plywood top) ring shank nails. (4),equally spaced,staggered center rows TA,APP-TA
W-109 Min.19/32- Elastobase,Elastobase P(poly-film 32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular 4-inch o.c.in 4-inch lap and 4-inch o.c.in four Polyflex SA Base APP-TA -97.5
inch plywood top) ring shank nails. (4),equally spaced,staggered center rows
32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular o. Elastoflex SA V Plus,
W-110 Min.19/32- Elastobase,Elastobase P(poly-film ring shank nails. Note:Tin caps are to be primed with (-inch o.c.in 4-inch lap and 6-inch center
r in four Elastoflex SA V Plus TA,AP,APP-SA,SBS-P-TA _112.5
inch plywood top) PG100 orASTM D41 primer. (4),equally spaced,staggered center rows FFIRTA,
32 ga.,1-5/8-inch diameter tin caps with 11 ga.annular
W-111 Min.19/32- Elastobase,Elastobase P(poly-film ring shank nails. Note:Tin caps are to be primed with (-inch o.c.in 4-inch lap and 6-inch Polyflex SA Base APP-TA -112.5
inch plywood top) PG100 or ASTM D41 primer. (4),equally spaced,staggered centerer in four r rows
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 18 of 58
QOTRINITY 'ERD
TABLE 1F-2: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE E: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(SCREWS&PLATES),BONDED ROOF COVER
System Deck(Note 1) Base Sheet Roof Cover(Note 15) MDP
No. Type Fasten Attach Base Ply Cap (psf)
NO BASE PLY:
Elastobase,Elastobase P,
Polyglass G2 Base, OMG Flat Bottom Plates(square)with Roofgrip#14,
Min.19/32- CertainTeed Glasbase, 12-inch o.c.in 4-inch lap and 12-inch o.c.in two SBS-AA,SBS-TA,APP-
W-112 inch plywood Firestone MB Base,JM Dekfast Hex(aka,Dekfast PLT- with Dekfast#14 (2) equally spaced,staggered center rows None TA 52.5
Perma-Ply 28,Tamko Glass or Trufast 3"Metal Insulation Pllateate with Trufast HD
Base or GAFGLAS#75
W-113 Min.19/32- Elastobase,Elastobase P OMG Flat Bottom Plates(square)with Roofgrip#12 12-inch o.c.in 4-inch lap and 12-inch o.c.in two None SBS-AA,SBS-TA,APP- -60.0
inch plywood (2),equally spaced,staggered center rows TA
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
W-114 Min.15/32- Polyglass G2 Base, CMG 3"Round Metal Plate with CMG HD,OMG Flat 10-inch o.c.in 4-inch lap and 10-inch o.c.in three None SBS-AA,SBS-TA,APP- -75.0
inch plywood Elastobase,Elastobase P Bottom Plate(Accutrac)with Roofgrip#14 or Trufast 3" (3),equally spaced,staggered center rows TA
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
W-115 Min.15/32- Polyglass APP Base CMG 3"Round Metal Plate with OMG HD,OMG Flat 10-inch o.c.in 4-inch lap and 10-inch o.c.in three None APP-TA -75.0
inch plywood Bottom Plate(Accutrac)with Roofgrip#14 or Trufast 3" (3),equally spaced,staggered center rows
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
W-116 Min.15/32- Polyglass G2 Base, CMG 3"Round Metal Plate with CMG HD,OMG Flat 9-inch o.c.in 4-inch lap and 9-inch o.c.in four(4), None SBS-AA,SBS-TA,APP- -90.0
inch plywood Elastobase,Elastobase P Bottom Plate(Accutrac)with Roofgrip#14 or Trufast 3" equally spaced,staggered center rows TA
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
W-117 Min.15/32- Polyglass APP Base CMG 3"Round Metal Plate with OMG HD,CMG Flat 9-inch o.c.in 4-inch lap and 9-inch o.c.in four(4), None APP-TA -90.0
inch plywood Bottom Plate(Accutrac)with Roofgrip#14 or Trufast 3" equally spaced,staggered center rows
Metal Insulation Plate with Trufast HD.
W-118 Min.15/32- Elastobase,Elastobase P Trufast#12 DP or Trufast#14 HD with Trufast 3"Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in three(3), None SBS-AA -90.0
inch plywood Insulation Plates equally spaced,staggered center rows
OMG#12 Standard Roofgrip or OMG#14 Heavy Duty with
W-119 Min.15/32- Elastobase,Elastobase P OMG 3"Round Metal Plates or OMG Flat Bottom Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in three(3), None SBS-AA,SBS-TA or -90.0
inch plywood Plates equally spaced,staggered center rows APP-TA
OMG#12 Standard Roofgrip or OMG#14 Heavy Duty with
W-120 Min.15/32- Polyglass APP Base OMG 3"Round Metal Plates or OMG Flat Bottom Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in three(3), None APP-TA -90.0
Plates
inch plywood equally spaced,staggered center rows
W-121 Min.15/32- Elastobase,Elastobase P Trufast#12 DP or Trufast#14 HD with Trufast 3"Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in five(5), None SBS-AA -120.0
inch plywood Insulation Plates equally spaced,staggered center rows
OMG#12 Standard Roofgrip or OMG#14 Heavy Duty with
W 122 Min.15/32- Elastobase,Elastobase P OMG 3"Round Metal Plates or OMG Flat Bottom Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in five(5), None SBS-AA,SBS-TA or -120.0
inch plywood Plates equally spaced,staggered center rows APP-TA
OMG#12 Standard Roofgrip or OMG#14 Heavy Duty with
W-123 Min.15/32- Polyglass APP Base OMG 3"Round Metal Plates or OMG Flat Bottom Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in five(5), None APP-TA -120.0
inch plywood Plates equally spaced,staggered center rows
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 19 of 58
QO
TRINITY ERD
TABLE 1F-2: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE E: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(SCREWS&PLATES),BONDED ROOF COVER
System Deck(Note 1) Base Sheet Roof Cover(Note 15) MOP
No. Type Fasten Attach Base Ply Cap (psf)
ASPHALT-APPLIED OR TORCH-APPLIED BASE PLY:
Elastobase,Elastobase P,
Polyglass G2 Base, OMG Flat Bottom Plates(square)with Roofgrip#14,
Min.19/32- CertainTeed Glasbase, 12-inch D.C.in 4-inch lap and 12-inch D.C.in two BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS-
W 124 inch plywood Firestone MB Base,JM Dekfast Hex(aka,Dekfast PLT- with Dekfast#14 (2) equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA 52.5
Perma-Ply 28,Tamko Glass or Trufast 3"Metal Insulation Pllateate with Trufast HD
Base or GAFGLAS#75
W-125 Min.19/32- Elastobase,Elastobase P OMG Flat Bottom Plates(square)with Roofgrip#12 12-inch o.c.in 4-inch lap and 12-inch o.c.in two BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS- -60.0
inch plywood (2),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
Min.15/32- Polyglass G2 Base, CMG 3"Round Metal Plate with CMG HD,CMG Flat 10-inch o.c.in 4-inch lap and 10-inch o.c.in three BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS-
W-126 inch plywood Elastobase,Elastobase P Bottom Plate(Accutrac)with Roofgrip#14 or Trufast 3" (3),equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA 75.0
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
W 127 Min.15/32- Polyglass APP Base CMG 3"Round Metal Plate with CMG HD,CMG Flat 10-inch o.c.in 4-inch lap and 10-inch o.c.in three APP-TA APP-TA -75.0
inch plywood Bottom Plate(Accutrac)with Roofgrip#14 or Trufast 3" (3),equally spaced,staggered center rows
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
Min.15/32- Polyglass G2 Base, CMG 3"Round Metal Plate with CMG HD,CMG Flat 9-inch o.c.in 4-inch lap and 9-inch o.c.in four(4), BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS-
W 128 90.0
inch plywood Elastobase,Elastobase P Bottom Plate(Accutrac)with Roofgrip#14 or Trufast 3" equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA
Metal Insulation Plate with Trufast HD.
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
W-129 Min.15/32- Polyglass APP Base CMG 3"Round Metal Plate with CMG HD,CMG Flat 9-inch o.c.in 4-inch lap and 9-inch o.c.in four(4), APP-TA APP-TA -90.0
inch plywood Bottom Plate(Accutrac)with Roofgrip#14 or Trufast 3" equally spaced,staggered center rows
Metal Insulation Plate with Trufast HD.
W-130 Min.15/32- Elastobase,Elastobase P Trufast#12 DP or Trufast#14 HD with Trufast 3"Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in three(3), BP-AA or SBS-AA SBS-AA -90.0
inch plywood Insulation Plates equally spaced,staggered center rows
OMG#12 Standard Roofgrip or OMG#14 Heavy Duty
Min.15/32- 6-inch o.c.at 4-inch lap and 6-inch o.c.in three(3), BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS-
W-131 inch plywood Elastobase,Elastobase P (min.1-5/8-inch long)with OMG 3"Round Metal Plates or equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA -90.0
CMG Flat Bottom Metal Plates
OMG#12 Standard Roofgrip or CMG#14 Heavy Duty with
W-132 Min.15/32- Polyglass APP Base OMG 3"Round Metal Plates or OMG Flat Bottom Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in three(3), APP-TA APP-TA -90.0
inch plywood Plates equally spaced,staggered center rows
W-133 Min.15/32- Elastobase,Elastobase P Trufast#12 DP or Trufast#14 HD with Trufast 3"Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in five(5), BP-AA or SBS-AA SBS-AA -120.0
inch plywood Insulation Plates equally spaced,staggered center rows
OMG#12 Standard Roofgrip or CMG#14 Heavy Duty with
Min.15/32- 6-inch o.c.at 4-inch lap and 6-inch o.c.in five(5), BP-AA,SBS-AA,SBS- SBS-SA,APP-SA,SBS-
W-134 inch plywood Elastobase,Elastobase P OMG 3"Round Metal Plates or OMG Flat Bottom Metal equally spaced,staggered center rows TA,APP-TA AA,SBS-TA,APP-TA 120.0
Plates
OMG#12 Standard Roofgrip or OMG#14 Heavy Duty with
W-135 Min.15/32- Polyglass APP Base OMG 3"Round Metal Plates or OMG Flat Bottom Metal 6-inch o.c.at 4-inch lap and 6-inch o.c.in five(5), APP-TA APP-TA -120.0
inch plywood Plates equally spaced,staggered center rows
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 20 of 58
QO
TRINITY ERD
TABLE 1F-2: WOOD DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE E: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET(SCREWS&PLATES),BONDED ROOF COVER
System Deck(Note 1) Base Sheet Roof Cover(Note 15) MOP
No. Type Fasten Attach Base Ply Cap (psf)
SELF-ADHERING BASE PLY:
W-136 Min.19/32- Elastobase,Elastobase P Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14 12-inch o.c.in 4-inch lap and 12-inch o.c.in two SBS-SA SBS-SA,APP-SA,SBS- _52.5*
inch plywood (poly-film top) or Trufast 3"Metal Insulation Plate with Trufast HD (2),equally spaced,staggered center rows TA,APP-TA
W-137 Min.19/32- Elastobase,Elastobase P Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#14 12-inch o.c.in 4-inch lap and 12-inch o.c.in two Polyflex SA Base APP-TA -52.5*
inch plywood (poly-film top) or Trufast 3"Metal Insulation Plate with Trufast HD (2),equally spaced,staggered center rows
W-138 Min.19/32- Elastobase,Elastobase P OMG Flat Bottom Plates(square)with Roofgrip#12 12-inch o.c.in 4-inch lap and 12-inch o.c.in two SBS-SA SBS-SA,APP-SA,SBS- _60.0*
inch plywood (poly-film top) (2),equally spaced,staggered center rows TA,APP-TA
W-139 Min.19/32- Elastobase,Elastobase P OMG Flat Bottom Plates(square)with Roofgrip#12 12-inch o.c.in 4-inch lap and 12-inch o.c.in two Polyflex SA Base APP-TA -60.0*
inch plywood (poly-film top) (2),equally spaced,staggered center rows
TABLE 1G: WOOD DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE F:NON-INSULATED,BONDED ROOF COVER
System Deck(Note 1) Primer Roof Cover(Note 15) MDP(psf)
No. Joint Treatment Base Ply Ply Cap Ply
W-140 Min.15/32- None None SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA,SBS- -90.0
inch plywood TA,APP-TA TA,APP-TA
W-141 Min.15/32- (Optional)PG100 None Polyflex SA Base (Optional)APP-TA APP-TA -90.0
inch plywood
W-142 Min.15/32- PG100 None SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA,SBS- 97 5
inch plywood TA,APP-TA TA,APP-TA
Min.15/32- Plywood joints are covered with 4-inch wide strips of Elastoflex SA V Plus,rolled into Elastoflex SA V Base or (Optional)SBS-SA,SBS- SBS-SA,APP-SA,SBS-
W-143 inch plywood (Optional)PG100 place to create continuous bond. Elastoflex SA V FR Base TA,APP-TA TA,APP-TA 97.5
W-144 Min.15/32- WB-3000 None SBS-SA (Optional) SBS-SA,APP-SA,SBS- -105.0
inch plywood TA,APP-TA
Min.15/32- Plywood joints are covered with 4-inch wide strips of Elastoflex SA V Plus,rolled into Elastoflex SA V Plus or (Optional)SBS-SA,SBS- SBS-SA,APP-SA,SBS-
W-145 inch plywood (Optional)PG100 place to create continuous bond. Elastoflex SA V Plus FR TA,APP-TA TA,APP-TA 135.0
W-146 Min.15/32- (Optional)PG100 Plywood joints are covered with 4-inch wide strips of Elastoflex SA V Plus,rolled into Polyflex SA Base (Optional)APP-TA APP-TA -135.0
inch plywood place to create continuous bond.
Exterior Research and Design,I.I.C.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 21 of 58
QO
TRINITY ERD
TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE B: MECHANICALLY ATTACHED BASE INSULATION,BONDED TOP INSULATION,BONDED ROOF COVER
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MOP
No. (Note 1) Type Fasten Attach Type Attach Base Ply Ply Cap Ply (PA
SELF-ADHERING BASE:
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.25-inch Dens Deck Prime,
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" SBS-CA1,
SC-1. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG 1 per 4 DEXcell FA Glass Mat Roof Board or ft2 D-IS SBS-SA None SBS-CA2, -30.0*
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal PRIMER: WB-3000 Gypsum-Fiber Roof Board APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD PRIMER:
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.25-inch Dens Deck Prime,
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" SBS-CA1,
1 per DEXcell FA Glass Mat Roof Board or
SC-2. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG 1.6 ft2 SECUROCK Gypsum-Fiber Roof Board D-IS SBS-SA None SBS-CA2, -45.0
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD PRIMER: WB-3000
Min.0.25-inch Dens Deck,Dens Deck
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2- Prime,DEXcell FA Glass Mat Roof
SECUROCK Gypsum-Fiber Roof
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" Board, SBS-CA1,
1 per 4 Board or SECUROCK Glass-Mat Roof M-OSFA
SC-3. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with CMG ft Board,min. inch DEXcell or M-PG1 2 SBS-SA None SBS-CA2, -30.0*
Cement Rooff Board structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal oard or min.0.5-inch APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD SECUROCK Cement Roof Board
PRIMER: WB-3000
Min.0.25-inch Dens Deck,Dens Deck
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2- Prime,DEXcell FA Glass Mat RoofBoard,SECUROCK Gypsum-Fiber Roof
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" SBS-CA1,
1 per Board or SECUROCK Glass-Mat Roof M-OSFA
SC-4. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG 2 SBS-SA None SBS-CA2, -45.0
1.6 ft Board,min.7/16-inch DEXcell or M-PG1
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal Cement Roof Board or min.0.5-inch APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD SECUROCK Cement Roof Board
PRIMER: WB-3000
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.25-inch Dens Deck Prime,
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" ,SBS-CA1
1 per 4 DEXcell FA Glass Matg Roof Board or SC-5. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with CMG ft2 SECUROCK Gypsum-Fiber Roof Board OB500 SBS-SA None SBS-CA2, -30.0*
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD PRIMER: WB-3000
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.25-inch Dens Deck Prime,
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" SBS-CA1,
SC-6. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG 1 per DEXcell FA Glass m-Fiatg Roof Board or OB500 SBS-SA None SBS-CA2, -45.0
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal 1.6 ft PRIMER:
Gypsum-Fiber Roof Board APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD PRIMER: WB-3000
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2-
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" 1 per 4 Min.0.25-inch Dens Deck Prime or SBS-CA1,
SC-7. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG ft2 SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA None SBS-CA2, -30.0
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal PRIMER: WB-3000 APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD
Exterior Research and Design,I.I.C.d/b/a Trinity)ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6TR EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 22 of 58
QO
TRINITY ERD
TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE B: MECHANICALLY ATTACHED BASE INSULATION,BONDED TOP INSULATION,BONDED ROOF COVER
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1) Type Fasten Attach Type Attach Base Ply Ply Cap Ply (psf)
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2-
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" 1 per Min.0.25-inch Dens Deck Prime or SBS-CA1,
SC-8. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG 1.6 ftZ SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-SA None SBS-CA2, -45.0
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal PRIMER: WB-3000 APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD
ASPHALT-APPLIED BASE:
Min.22 ga.,type Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.75-inch Fesco Board (Optional if (Optional if using
B,Grade 33 steel Min.1.5-inch Polytherm, 7/8)with Dekfast#14,Trufast 3" SBS-AA,
1 per 2 (homogeneous)or min.0.5-inch Hot using AA AA Base)BP-AA,
SC-9. or min.2,500 psi ACFoam II,ENRGY 3,H- Metal Insulation Plate with Trufast ftZ Structodek High Density Fiberboard asphalt Ply)BP-AA, SBS-AA,SBS-TA or SBS-TA, -45.0*
structrual Shield or Polytherm HD or OMG 3-inch Galy Plate with Roof Insulation SBS-AA APP-TA APP-TA
concrete OMD HD
Min.22 ga.,type Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.75-inch Fesco Board (Optional if (Optional if using
B,Grade 33 steel Min.2-inch Polytherm, 7/8)with Dekfast#14,Trufast 3" SBS-AA,
1 per 4 (homogeneous)or min.0.5-inch Hot using AA AA Base)BP-AA,
SC-10. or min.2,500 psi ACFoam ll,ENRGY 3,H- Metal Insulation Plate with Trufast ftZ Structodek High Density Fiberboard asphalt Ply)BP-AA, SBS-AA,SBS-TA or SBS-TA, -45.0*
structrual Shield or Polytherm HD or OMG 3-inch Galy Plate with Roof Insulation SBS-AA APP-TA APP-TA
concrete OMD HD
Min.22 ga.,type Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.75-inch Fesco Board (Optional if (Optional if using
B,Grade 33 steel SBS-AA,
Min.1.5-inch ENRGY 3,H- 7/8)with Dekfast#14 or Trufast 3" 1 per (homogeneous)or min.0.5-inch Hot using AA AA Base)BP-AA,
SC-11. or min.2,500 psi Shield or Polytherm Metal Insulation Plate with Trufast 1.33 ftZ Structodek High Density Fiberboard asphalt Ply)BP-AA, SBS-AA,SBS-TA or SBS-TA, -90.0
structrual HD Roof Insulation SBS-AA APP-TA APP-TA
concrete
Min.22 ga.,type BP-AA,SBS-
B,Grade 33 steel Dekfast Hex(aka,Dekfast PLT-H-2- Min.0.75-inch Fesco Board AA(Top SBS-SA,
Min.1.5-inch ENRGY 3,H- 7/8)with Dekfast#14 or Trufast 3" 1 per (homogeneous)or min.0.5-inch Hot surface SBS-SA,SBS-TA or APP-SA,
SC-12. or min.2,500 psi Shield or Polytherm Metal Insulation Plate with Trufast 1.33 ftz Structodek High Density Fiberboard asphalt primed with APP-TA SBS-TA or -90.0
structrual HD Roof Insulation PG100 APP-TA
concrete
primer)
COLD-APPLIED BASE:
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2-
B,Grade 40 steel ACFoam ll,ENRGY 3, 7/8)with Dekfast#14,OMG 3" Min.0.25-inch Dens Deck Prime, SBS-CAI,
1 per 4 SBS-CA1, (Optional)SBS-CA1,
SC-13. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG ftZ DEXcell FA Glass Mat Roof Board or D-IS SBS-CA2 SBS-CA2 SBS-CA2, -30.0*
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal SECUROCK Gypsum-Fiber Roof Board APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2-
B,Grade 40 steel ACFoam ll,ENRGY 3, 7/8)with Dekfast#14,OMG 3" Min.0.25-inch Dens Deck Prime, SBS-CA1,
1
SC-14. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG .Pe z DEXcell FA Glass Mat Roof Board or D-IS SBS-CA2, (Optional)SBS-CA1, SBS-CA2, -45.0
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal 6 ft SECUROCK Gypsum-Fiber Roof Board SBS-CA2 SBS-CA2 APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD
Exterior Research and Design,LLC.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 23 of 58
QO
TRINITY ERD
TABLE 2A: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE B: MECHANICALLY ATTACHED BASE INSULATION,BONDED TOP INSULATION,BONDED ROOF COVER
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1) Type Fasten Attach Type Attach Base Ply Ply Cap Ply (psf)
Min.0.25-inch Dens Deck,Dens Deck
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2- Prime,DEXcell FA Glass Mat Roof
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" Board,SECUROCK Gypsum-Fiber Roof SBS-CA1,
SC-15. or min.2,S00 psi EnergyGuard Galvalume Ribbons Plates with OMG 1 per 4 M-OSFA SBS-CA2, (Optional)SBS CA1,
p gy Polyiso y' ftZ Board or SECUROCK Glass-Mat Roof or M-PG1 SBS-CA2 SBS-CA2 SBS-CA2, -30.0*
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal Board,min.7/16-inch DEXcell APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD Cement Roof Board or min.0.5-inch
SECUROCK Cement Roof Board
Min.0.25-inch Dens Deck,Dens Deck
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2- Prime,DEXcell FA Glass Mat Roof
B,Grade 40 steel ACFoam II,ENRGY 3, 7/8)with Dekfast#14,OMG 3" Board,SECUROCK Gypsum-Fiber Roof SBS-CA1,
SC-16. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG 1 pe z Board or SECUROCK Glass-Mat Roof M-OSFA SBS-CAI, (Optional)5B5-CAI, SBS-CA2, -45.0
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal 1.6 ft Board,min.7/16-inch DEXcell or M-PG1 5B5-CA2 SBS-CA2 APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD Cement Roof Board or min.0.5-inch
SECUROCK Cement Roof Board
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2-
B,Grade 40 steel ACFoam ll,ENRGY 3, 7/8)with Dekfast#14,OMG 3" Min.0.25-inch Dens Deck Prime, SBS-CA1,
1 per 4 5B5-CAI, (Optional)SBS-CA1,
SC-17. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG ftZ DEXcell FA Glass Matg Roof Board or OB500 SBS-CA2 SBS-CA2 SBS-CA2, -30.0*
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal SECUROCK Gypsum-Fiber Roof Board APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2-
B,Grade 40 steel ACFoam ll,ENRGY 3, 7/8)with Dekfast#14,OMG 3" Min.0.25-inch Dens Deck Prime, SBS-CA1,
SC-18. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG 1 pe Z DEXcell FA Glass Matg Roof Board or OB500 SBS-CA2, (Optional)SBS-CAl, SBS-CA2, -45.0
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal 1.6 ft SECUROCK Gypsum-Fiber Roof Board SBS-CA2 SBS-CA2 APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2-
B,Grade 40 steel ACFoam ll,ENRGY 3, 7/8)with Dekfast#14,OMG 3" SBS-CA1,
1 per 4 Min.0.25-inch Dens Deck Prime or SBS-CAI, (Optional)SBS-CA1,
SC-19. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG ftz SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA2 SBS-CA2 SBS-CA2, -30.0*
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD
Min.22 ga.,type Min.2-inch Polytherm, Dekfast Hex(aka,Dekfast PLT-H-2-
B,Grade 40 steel ACFoam ll,ENRGY 3, 7/8)with Dekfast#14,OMG 3" SBS-CA1,
1 per Min.0.25-inch Dens Deck Prime or SBS-CA1, (Optional)SBS-CA1,
SC-20. or min.2,500 psi EnergyGuard Polyiso Galvalume Ribbons Plates with OMG 1.6 ftz SECUROCK Gypsum-Fiber Roof Board CR-20 SBS-CA2 SBS-CA2 SBS-CA2, -45.0
structrual Insulation,Polytherm H,H- #14 Roofgrip or Trufast 3"Metal APP-CA1
concrete Shield or Multi-Max FA3 Insulation Plate with Trufast HD
Exterior Research and Design,LLC.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 24 of 58
QO
TRINITY ERD
TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER
System Top Insulation Layer Roof Cover(Note 15) MDP
No. Deck(Note 1) Base Insulation Layer Type Fasten Attach Base Ply Ply Cap Ply (psf)
SELF-ADHERING BASE:
Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 DP
Min.22 ga.,type B, (Optional)One or SBS-SA,
Grade 33 steel or min. more layers,any Min.1.5-inch Polytherm, (steel only)or Dekfast#14,OMG AccuTrac Flat Bottom 1 per (Optional)SBS-SA, APP-SA,
SC-21. ACFoam II,H-Shield or Plate with#12 Roofgrip(steel only)or OMG#14 Heavy 2 SBS-SA -30.0
concrete laid 2,500 psi structrual combination,loose Polytherm Duty,Trufast 3"Metal Insulation Plate with Trufast#12 DP 2.67 ft SBS-TA,APP-TA SBS-TA,
concr APP-TA
(steel only)or Trufast#14 HD
Min.22 ga.,type B, (Optional)One or Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 DP
Min.1.5-inch Polytherm, (steel only)or Dekfast#14,OMG AccuTrac Flat Bottom
SC-22. Grade psi
steel ru min. more layers,any ACFoam II,H-Shield or Plate with#12 Roofgrip(steel only)or OMG#14 Heavy 1 per Polyflex SA (Optional)APP-TA APP-TA -30.0
concrete
psi structrual combination,loose Polytherm Duty,Trufast 3"Metal Insulation Plate with Trufast#12 DP 2.67 ft Base
concrete laid (steel only)or Trufast#14 HD
Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Min.22 ga.,type B, (Optional for recover) SBS-SA,
Grade 40 steel or min. One or more layers, Min.0.25-inch Dens Deck Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast 1 per (Optional)SBS-SA, APP-SA,
SC-23. Prime optionally primed PLT-H-2-7/8)or OMG#14 Roofgrip or#15 Roofgrip with 2 SBS-SA -37.5*
concrete
psi structrual any combination,min. with WB-3000 OMG 3 in.Round Metal Plate or Trufast#14 HD or Trufast 2.67 ft SBS-TA,APP-TA SBS-TA,
concrete 1-inch,loose laid APP-TA
#15 EHD Fasteners with Trufast 3"Metal Insulation Plate
Min.22 ga.,type B, (Optional for recover) Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Min.0.25-inch Dens Deck Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast
Grade 40 steel ru min. One o more layers, 1 per Polyflex SA (Optional)APP-TA APP-TA -37.5*
SC-24. Prime optionally primed PLT-H-2-7/8)or OMG#14 Roofgrip or#15 Roofgrip with 2
concrete
psi structrual any combination,min. with WB-3000 OMG 3 in.Round Metal Plate or Trufast#14 HD or Trufast 2.67 ft Base
concrete 1-inch,loose laid #15 EHD Fasteners with Trufast 3"Metal Insulation Plate
Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch SECUROCK Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast SBS-SA,
Grade 40 steel or min. One or more layers, Gypsum-Fiber Roof Board PLT-H-2-7/8)or OMG#14 Roofgrip or#15 Roofgrip with 1 per (Optional)SBS-SA, APP-SA,
SC-25. 2,500 psi structrual any combination,min. optionally primed with OMG 3 in.Round Metal Plate or Accutrac Flat Bottom Plate 2.67 ft2 SBS-SA SBS-TA,APP-TA SBS-TA, 37.5*
concrete 1-inch,loose laid WB-3000 or Trufast#14 HD or Trufast#15 EHD Fasteners with Trufast APP-TA
3"Metal Insulation Plate
Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch SECUROCK Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast
Grade 40 steel or min. One or more layers, Gypsum-Fiber Roof Board PLT-H-2-7/8)or OMG#14 Roofgrip or#15 Roofgrip with 1 per Polyflex SA *
SC-26. 2,500 psi structrual any combination,min. optionally primed with OMG 3 in.Round Metal Plate or Accutrac Flat Bottom Plate 2.67 ft2 Base (Optional)APP-TA APP-TA 37.5
concrete 1-inch,loose laid WB-3000 or Trufast#14 HD or Trufast#15 EHD Fasteners with Trufast
3"Metal Insulation Plate
Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch DEXcell FA PLT-H-2-7/8),isofast PLT-S-2-3/4X2-3/4 or Dekfast SBS-SA,
SC-27. Grade 40 steel or min. One or more layers, Glass Mat Roof Board Galvalume Steel 3"Round(aka,Dekfast PLT-R-3)or OMG 1 per Z SBS-SA (Optional)SBS-SA, APP-SA, 37.5*
2,500 psi structrual any combination,min. optionally primed with #14 Roofgrip or#15 Roofgrip with OMG 3 in.Round Metal 2.67 ft SBS-TA,APP-TA SBS-TA,
concrete 1-inch,loose laid WB-3000 Plate or Accutrac Flat Bottom Plate or Trufast#14 HD or APP-TA
Trufast#15 EHD Fasteners with Trufast 3"Metal Insulation
Plate
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 25 of 58
QO
TRINITY ERD
TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER
System Top Insulation Layer Roof Cover(Note 15) MDP
No. Deck(Note 1) Base Insulation Layer Type Fasten Attach Base Ply Ply Cap Ply (psf)
Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch DEXcell FA PLT-H-2-7/8),isofast PLT-S-2-3/4X2-3/4 or Dekfast
Grade 40 steel or min. One or more layers, Glass Mat Roof Board Galvalume Steel 3"Round(aka,Dekfast PLT-R-3)or OMG 1 per Polyflex SA
SC-28. 2,500 psi structrual any combination,min. optionally primed with #14 Roofgrip or#15 Roofgrip with OMG 3 in.Round Metal 2.67 ftz Base (Optional)APP-TA APP-TA -37.5
concrete 1-inch,loose laid WB-3000 Plate or Accutrac Flat Bottom Plate or Trufast#14 HD or
Trufast#15 EHD Fasteners with Trufast 3"Metal Insulation
Plate
Min.22 ga.,type B, (Optional)One or SBS-SA,
OMG AccuTrac Flat Bottom Plate with#12 Roofgrip(steel
Grade 33 steel or min. more layers,any Min.1.5-inch H-Shield or 1 per 2 (Optional)SBS-SA, APP-SA,
SC-29. 2,500 psi structrual combination,loose Polytherm only)or OMG#14 Heavy Duty,Trufast 3"Metal Insulation ftZ SBS-SA SBS-TA,APP-TA SBS-TA, -45.0*
concrete laid Plate with Trufast#12 DP(steel only)or Trufast#14 HD APP-TA
Min.22 ga.,type B, (Optional)One or OMG AccuTrac Flat Bottom Plate with#12 Roofgrip(steel
Grade 33 steel or min. more layers,any Min.1.5-inch H-Shield or 1 per 2 Polyflex SA
SC-30. 2,500 psi structrual combination,loose Polytherm only)or OMG#14 Heavy Duty,Trufast 3"Metal Insulation ftz Base (Optional)APP-TA APP-TA -45.0
concrete laid Plate with Trufast#12 DP(steel only)or Trufast#14 HD
25-inch Dens Deck 0.
Min.22 ga.,type B, (Optional for recover) Min. Dekfast Hex Prime or SECUROCK (aka,Dekfast PLT-H-2-7/8)with Dekfast#14,
SBS-CA1,
Grade 33 steel or min. One or more layers, OMG 3"Galvalume Ribbed Plates with OMG#14 RoofGrip 1 per 2 SC-31. 2,500 psi structrual any combination, Gypsum-Fiber Roof Board or Trufast 3"Metal Insulation Plates with Trufast#14 HD ftz SBS-SA None SBS-CA2, -45.0*
concrete loose laid optionally primed with Fasteners APP-CA1
W B-3000
Min.0.25-inch Dens Deck OMG 3 in.Galvalume Plate(non-ribbed)with#12 Roofgrip
Min.22 ga.,type B, (Optional for recover) SBS-SA,
Prime or SECUROCK (steel only)or OMG#14 Heavy Duty,Dekfast Hex(aka,
SC-32. Grade psi
steel ru min. One o more layers, Gypsum-Fiber Roof Board Dekfast PLT-H-2-7 8 with Dekfast#12 DP steel only)or 1 per 2 (Optional)SBS-SA, APP-SA,
2,500 psi structrual any combination, Yp / ) ( Y) ftz SBS-SA SBS-TA or APP-TA SBS-TA or -45.0*
concrete loose laid optionally primed with Dekfast#14,Trufast 3"Metal Insulation Plate with Trufast APP-TA
WB-3000 #12 DP(steel only)or Trufast#14 HD
Polygrip#14 with Polygrip Hex Plate or Dekfast#14 with
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch SECUROCK Dekfast Hex(aka,Dekfast PLT-H-2-7/8)or Dekfast
Dekfast PLT-R-3)or OMG
Grade 40 steel or min. One or more layers, Gypsum-Fiber Roof Board Galvalume Steel 3"Round(aka, 1 per 2
SC-33. 2,500 psi structrual any combination,min. optionally primed with ft#14 Roofgrip with OMG 3 in.Round Metal Plate,OMG 3 in. z SBS-SA None SBS-SA -45.0
concrete 1-inch,loose laid WB-3000 Ribbed Galvalume Plate(Flat)or Accutrac Flat Bottom Plate
or Trufast#14 HD Fasteners with Trufast 3"Metal
Insulation Plate
Min.22 ga.,type B, (Optional for recover) Polygrip#14 with Polygrip Hex Plate or Dekfast#14 with
Min.0.25-inch Dens Deck Dekfast Hex(aka,Dekfast PLT-H-2-7/8)or OMG#14
Grade 40 steel or min. One or more layers, 1 per 2
SC-34. 2,500 psi structrual any combination,min. Prime optionally primed Roofgrip with OMG 3 in.Round Metal Plate or Accutrac Flat ftz SBS-SA None SBS-SA -45.0
concrete 1-inch,loose laid with WB-3000 Bottom Plate or Trufast#14 HD Fasteners with Trufast 3"
Metal Insulation Plate
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 26 of 58
QO
TRINITY ERD
TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER
System Top Insulation Layer Roof Cover(Note 15) MDP
No. Deck(Note 1) Base Insulation Layer Type Fasten Attach Base Ply Ply Cap Ply (psf)
Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch SECUROCK Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast (Optional when SBS-SA,
Grade 40 steel or min. One or more layers, Gypsum-Fiber Roof Board PLT-H-2-7/8)or OMG#14 Roofgrip or#15 Roofgrip with 1 per using torch-applied APP-SA,
SC-35. 2,500 psi structrual any combination,min. optionally primed with OMG 3 in.Round Metal Plate or Accutrac Flat Bottom Plate 1.78 ftZ SBS-SA Cap Ply)SBS-TA, SBS-TA or -45.0
concrete 1-inch,loose laid WB-3000 or Trufast#14 HD or Trufast#15 EHD Fasteners with Trufast APP-TA APP-TA
3"Metal Insulation Plate
Min.22 ga.,type B, (Optional for recover) (Optional when SBS-SA,
Min.0.25-inch Dens Deck OMG#14 Roofgrip or#15 Roofgrip with OMG 3 in.Round
SC-36. Grade 40 steel or min. One or more layers, Prime optionally primed Metal Plate or Trufast#14 HD or Trufast#15 EHD Fasteners . pe 2 SBS-SA using torch-applied APP-SA, -45.0
2,500 psi structrual any combination,min. 1.78 ft Cap Ply)SBS-TA, SBS-TA or
concrete 1-inch,loose laid with WB-3000 with Trufast 3"Metal Insulation Plate APP-TA APP-TA
Min.22 ga.,type B, (Optional)One or SBS-SA,
Grade 33 steel or min. more layers,any Min.1.5-inch H-Shield or Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 DP 1 per 2 (Optional)SBS-SA, APP-SA,
SC-37. 2,500 psi structrual combination,loose Polytherm (steel only)or Dekfast#14 ftZ SBS-SA SBS-TA,APP-TA SBS-TA, -60.0
concrete laid APP-TA
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch Dens Deck OMG 3 in.Galvalume Plate(non-ribbed)with#12 Roofgrip
Prime or SECUROCK (steel only)or OMG#14 Heavy Duty,Dekfast Hex(aka,
SC-38. Grade psi
steel ru min. One o more layers, Gypsum-Fiber Roof Board Dekfast PLT-H-2-7/8)with Dekfast#12 DP(steel only)or 1 per SBS-SA (Optional)SBS-TA SBS-TA or -60.0
concrete
psi structrual any combination, optionally primed with Dekfast#14,Trufast 3"Metal Insulation Plate with Trufast 1.6 ft or APP-TA APP-TA
concrete loose laid WB-3000 #12 DP(steel only)or Trufast#14 HD
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch Dens Deck OMG 3 in.Galvalume Plate(non-ribbed)with#12 Roofgrip
Prime or SECUROCK (steel only)or OMG#14 Heavy Duty,Dekfast Hex(aka,
SC-39. Grade psi
steel ru min. One o more layers, Gypsum-Fiber Roof Board Dekfast PLT-H-2-7 8 with Dekfast#12 DP steel only)or 1 per (Optional)SBS-TA 565-TA or
2,500 psi structrual any combination, yP / ) ( 1.33 ftZ SBS-SA or APP-TA APP-TA 72.5
concrete loose laid optionally primed with Dekfast#14,Trufast 3"Metal Insulation Plate with Trufast
WB-3000 #12 DP(steel only)or Trufast#14 HD
Min.22 ga.,type B, (Optional)One or
SC-40. Grade 33 steel or min. more layers,any Min.0.5-inch SECUROCK OMG 3-inch Galvalume Steel Plate with OMG#14 HD 1 per
2,500 psi structrual combination,loose Gypsum-Fiber Roof Board 1.78 ftZ SBS-SA (Optional)565-TA 565-TA 75.0
concrete laid
Min.22 ga.,type B, (Optional)One or SBS-SA,
Grade 33 steel or min. more layers,any Min.1.5-inch ENRGY 3,H- Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 1 per (Optional)SBS-SA, APP-SA,
SC-41. 2,500 psi structrual combination,loose Shield or Polytherm (steel only)or#14 or Trufast 3"Metal Insulation Plate with 1.33 ftZ SBS-SA SBS-TA,APP-TA SBS-TA, 82.5
concrete laid Trufast DP(steel only)or HD APP TA
Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch SECUROCK Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast
Grade 40 steel or min. One or more layers, Gypsum-Fiber Roof Board PLT-H-2-7/8)or OMG#14 Roofgrip or#15 Roofgrip with 1 per 1 (Optional)SBS-TA, SBS-TA,
SC 42. 2,500 psi structrual any combination,min. optionally primed with OMG 3 in.Round Metal Plate or Accutrac Flat Bottom Plate ftZ SBS-SA APP TA APP TA -90.0
concrete 1-inch,loose laid WB-3000 or Trufast#14 HD or Trufast#15 EHD Fasteners with Trufast
3"Metal Insulation Plate
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 27 of 58
QO
TRINITY ERD
TABLE 2B: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER
System Top Insulation Layer Roof Cover(Note 15) MDP
No. Deck(Note 1) Base Insulation Layer Type Fasten Attach Base Ply Ply Cap Ply (psf)
Min.22 ga.,type B, (Optional for recover) Polygrip#14 or Polygrip#15 with Polygrip Hex Plate or
Min.0.25-inch Dens Deck Dekfast DF-#14 or DF-#15 with Dekfast Hex(aka,Dekfast
Grade 40 steel or min. One or more layers, 1 per 1 (Optional)SBS-TA, SBS-TA,
SC-43. Prime optionally primed PLT-H-2-7/8)or OMG#14 Roofgrip or#15 Roofgrip with Z SBS-SA -97.5
concrete
psi structrual any combination,min. with WB-3000 OMG 3 in.Round Metal Plate or Trufast#14 HD or Trufast ft APP-TA APP-TA
concrete 1-inch,loose laid #15 EHD Fasteners with Trufast 3"Metal Insulation Plate
ASPHALT-APPLIED BASE:
OMG AccuTrac Plate or OMG 3 in.Ribbed Galvalume Plate
Min.22 ga.,type B, Min.0.75-inch JM Fesco (Optional if (Optional if using
Grade 33 steel or min. Board(homogeneous)or 1 per 2 using AA Ply) AA Base)BP-AA,
One or more layers, with#12 Roofgrip(steel only)or OMG#14 Heavy Duty, SBS-AA,
2,500 psi structrual min.1.5-inch JM Fesco ft BP-AA,SBS- SBS-AA,SBS-TA or
SC-44. any combination, Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 DP Z SBS-TA, -45.0*
concrete loose laid Board(laminated) (steel only)or Dekfast#14,Trufast 3"Metal Insulation Plate AA APP-TA APP-TA
with Trufast#12 DP(steel only)or Trufast#14 HD
OMG AccuTrac Plate or OMG 3 in.Ribbed Galvalume Plate
Min.22 ga.,type B, Min.0.5-inch Structodek (Optional if (Optional if using
One or more layers, with#12 Roofgrip(steel only)or OMG#14 Heavy Duty, SBS-AA,
Grade 33 steel or min. High Density Fiberboard 1 per 4 using AA Ply) AA Base)BP-AA,i
SC-45. 2,500 psi structrual any combination, Roof Insulation or G-P Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 DP ftZ BP-AA,SBS- SBS-AA,SBS-TA or SBS-TA, -45.0*
concrete loose laid FiberBase HD or HD Excel (steel only)or Dekfast#14,Trufast 3"Metal Insulation Plate AA APP TA APP-TA
with Trufast#12 DP(steel only)or Trufast#14 HD
OMG AccuTrac Plate or OMG 3 in.Ribbed Galvalume Plate
Min.22 ga.,type B, (Optional if (Optional if using
One or more layers, Min.0.25-inch Dens Deck with#12 Roofgrip(steel only)or OMG#14 Heavy Duty, SBS-AA, *
Grade 33 steel or min. 1 per 4 using AA Ply) AA Base)BP-AA, -45.0
SC-46. any combination, Prime or SECUROCK Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 DP Z SBS-TA,
concrete AA APP-TA psi structrual loose laid Gypsum-Fiber Roof Board (steel only)or Dekfast#14,Trufast 3"Metal Insulation Plate ft BP-AA,SBS- SBS-AA,SBS-TA or APP-TA
concr with Trufast#12 DP(steel only)or Trufast#14 HD
OMG AccuTrac Plate or OMG 3 in.Ribbed Galvalume Plate
Min.22 ga.,type B, (Optional)One or (Optional if (Optional if using
Grade 33 steel or min. more layers,any with#12 Roofgrip(steel only)or OMG#14 Heavy Duty, 1 per 4 using AA Ply) AA Base)BP-AA, SBS-AA,
2,500 psi structrual combination,loose ft BP-AA,SBS- SBS-AA,SBS-TA or
SC-47. Min.2-inch H-Shield WF Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 DP Z SBS-TA, -45.0*
concrete laid (steel only)or Dekfast#14,Trufast 3"Metal Insulation Plate AA APP TA APP-TA
with Trufast#12 DP(steel only)or Trufast#14 HD
Min.22 ga.,type B, (Optional)One or (Optional if (Optional if using SBS-AA,
Grade 33 steel or min. more layers,any Min.0.5-inch SECUROCK I per using AA Ply) AA Base)BP-AA,
SC-48. 2,500 psi structrual combination,loose Gypsum-Fiber Roof Board OMG 3-inch Galvalume Steel Plate with OMG#14 HD 1.78 ftZ BP-AA,SBS- SBS-AA,SBS-TA or SBS-TA, -75.0
concrete laid AA APP-TA APP TA
Min.0.5-inch Structodek
Min.22 ga.,type B, One or more layers, High Density Fiberboard Dekfast Hex(aka,Dekfast PLT-H-2-7/8)with Dekfast#12 (Optional if (Optional if using SBS-AA,
Grade 33 steel or min. Roof Insulation or min. I per using AA Ply) AA Base)BP-AA,
SC-49. 2,500 psi structrual any combination, 0.25-inch Dens Deck,Dens (steel only)or#14 or Trufast 3"Metal Insulation Plate with 1.33 ftZ BP-AA,SBS- SBS-AA,SBS-TA or SBS-TA, 82.5
concrete loose laid Deck Prime or SECUROCK Trufast DP(steel only)or HD AA APP TA APP-TA
Gypsum-Fiber Roof Board
COLD-APPLIED BASE: JIL
Min.22 ga.,type B, (Optional for recover) Min.0.25-inch Dens Deck Dekfast Galvalume Steel Hex with Dekfast#14,OMG 3" SBS-CA1,
SC-50. Grade 33 steel or min. One or more layers, prime or SECUROCK Galvalume Ribbed Plates with OMG#14 RoofGrip or Trufast 1 per 2 SBS-CAI,SBS- (Optional)SBS-CAI, SBS-CA2, 45.0*
concrete loose laid 2,500 psi structrual any combination, Gypsum-Fiber Roof Board 3"Metal Insulation Plates with Trufast#14 HD Fasteners ft CA2 SBS-CA2 APP-CA1
concrete
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL1654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 28 of 58
QOTFUNITY 'ERD
TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE D: PRELIMINARILY ATTACHED INSULATION,MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
NOTE: INSULATION IS OPTIONAL FOR RECOVER APPLICATIONS
System Deck Insulation Layer(s) Base Sheet Roof Cover(Note 15) MOP
No. (Note 1) Type Attach Type Fasten Attach Base Ply Cap Ply (psf)
Min.22 ga.,type B,40 ksi One or more Prelim. Elastoflex 56(film 18-inch o.c.within the 4-inch (Optional)SBS-
SC-51. steel or min.2,500 psi layers,any Trufast#14 HD with Trufast 2"Barbed Seam Plates wide,torch-sealed or heat- SBS-TA -30.0
structrual concrete combination Attached surfaced) welded side laps TA
Trufast#15 EHD(steel only)or Trufast#14 HD
(concrete only)with Trufast 2.4"Barbed Metal Seam
Plates,Trufast 2.4"Scoop Seam Plates or Trufast
Min.22 ga.,type B,Grade One or more 18-inch stag within the 5-inch
Prelim. Polyglass HT Base 2.75"Barbed Metal Seam Plates or Dekfast#15 with (Optional)SBS-
SC-52. 40 steel or min.2,500 psi layers,any wide,torch-sealed or heat- 565-TA -37.5
structrual concrete combination Attached 650 Dekfast Galvalume Steel 1-1/2"x 2-3/4"Oval Barbed welded side laps TA
Plate(aka,Dekfast PLT-02-3/4-12B)or Dekfast
Galvalume Steel 2-3/8"Round Barbed Plate(aka,
Dekfast PLT-R-2-3/8-6B)
12-inch stag at 4-inch lap and Min.22 ga.,type B,Grade One or more Elastobase,
Roofgrip#14 with OMG Flat Bottom Plates(square), (Optional)BP-
Prelim. Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-2- AA,SBS-AA, SBS-AA,SBS-
SC-53. t steel l min.2,500 psi layers any Attached Elastobase P or JM 7/8)or Trufast#14 HD with Trufast 3"Metal 18-inch stag at two,equally SBS-TA or APP- TA,APP-TA 45.0*
structrual concrete combination Perma-Ply 28 Insulation Plate spaced,staggered center rows TA
Min.22 ga.,type B,Grade One or more Loose 12-inch o.c.at 4-inch lap and
SC-54. 33 steel or min.2,500 psi layers,any Elastobase Trufast#12 DP(steel only),#14 HD or#15 EHD with 12-inch o.c.at one staggered (Optional)SBS- SBS-CAI,5B5- -45.0*
structrual concrete combination laid Trufast 3"Metal Insulation Plate center row CAI,SBS-CA2 CA2,APP-CAI
Min.22 ga.,type B,33 ksi One or more Trufast#15 EHD(steel only)or Trufast#14 HD 12-inch o.c.within the 5-inch
Prelim. (Optional)SBS-
SC-55. steel or min.2,500 psi layers,any Attached Elastoflex 56 (concrete only)with Trufast 2.4"Scoop Seam Plates wide,torch-sealed or heat- TA SBS-TA -45.0
structrual concrete combination or Trufast 2.75"Barbed Metal Seam Plates welded side laps
Elastobase,
Elastobase P,
12-inch stag at 4-inch lap and Min.22 ga.,type B,Grade One or more
Polyglass G2 Base, Roofgrip#14 with OMG Flat Bottom Plates(square), (Optional)BP-
Prelim. CertainTeed Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-2- AA,SBS-AA, SBS-AA,SBS-
SC-56. t steel l min.2,500 psi layers any Attached Glasbase,Firestone 7/8)or Trufast#14 HD with Trufast 3"Metal 12-inch stag at two,equally SBS-TA or APP- TA,APP-TA 52.5
structrual concrete combination MB Base,JM Perma- Insulation Plate spaced,staggered center rows TA
Ply 28,Tamko Glass
Base or GAFGLAS#75
Min.22 ga.,type B,Grade One or more Elastobase or Roofgrip#14 with OMG Flat Bottom Plates(square), 12-inch stag at 4-inch lap and 5B5-SA,APP-
Prelim. Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-2-
SC-57. 33 steel or min.2,500 psi layers,any Elastobase P with 12-inch stag at two,equally 565-SA SA,SBS-TA or -52.5*
structrual concrete combination Attached poly top surface 7/8)or Trufast#14 HD with Trufast 3"Metal spaced,staggered center rows APP-TA
Insulation Plate
Min.22 ga.,type B,Grade One or more Elastobase or Roofgrip#14 with OMG Flat Bottom Plates(square), 12-inch stag at 4-inch lap and
Dekfast PLT-H-2-Prelim. ,
SC-58. 33 steel or min.2,500 psi layers,any Elastobase P with Dekfast#14 with Dekfast Hex(aka 12-inch stag at two,equally Polyflex SA APP-TA -52.5*
structrual concrete combination Attached poly top surface 7/8)or Trufast#14 HD with Trufast 3"Metal spaced,staggered center rows Base
Insulation Plate
Min.22 ga.,type B,33 ksi One or more Trufast#15 EHD(steel only)or Trufast#14 HD 6-inch o.c.within the 5-inch
Prelim. (Optional)SBS-
SC-59. steel or min.2,500 psi layers,any Attached Elastoflex 56 (concrete only)with Trufast 2.75"Barbed Metal Seam wide,torch-sealed or heat- TA SBS-TA -60.0
structrual concrete combination Plates welded side laps
Exterior Research and Design,I.I.C.d/b/a Trinity)ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 29 of 58
QOTRINI-FY 'ERD
TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE D: PRELIMINARILY ATTACHED INSULATION,MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
NOTE: INSULATION IS OPTIONAL FOR RECOVER APPLICATIONS
System Deck Insulation Layer(s) Base Sheet Roof Cover(Note 15) MDP
No. (Note 1) Type Attach Type Fasten Attach Base Ply Cap Ply (psf)
Min.22 ga.,type B,Grade One or more Trufast#15 EHD(steel only)or Trufast#14 HD 18-inch o.c.within the 5-inch
Prelim. (Optional)SBS- SBS-TA
SC-60. 40 steel or min.2,500 psi layers,any Attached Elastoflex S6 Type II (concrete only)with Trufast 2.75"Barbed Metal Seam wide,torch-sealed or heat- TA (D6164 only) -60.0
structrual concrete combination Plates welded side laps
Min.22 ga.,type B,Grade One or more 12-inch o.c.at 4-inch lap and (Optional)BP-
SC-61. 33 steel or min.2,500 psi layers,any Prelim. Elastobase or Roofgrip#12(steel only)or#14 with OMG Flat 12-inch o.c.at two,equally AA,SBS-AA, SBS-AA,SBS- -60.0
structrual concrete combination Attached Elastobase P Bottom Plates(square) spaced,staggered center rows SBS-TA or APP- TA,APP-TA
TA
Min.22 ga.,type B,Grade One or more Prelim. Roofgrip#12(steel only)or#14 with OMG Flat Elastobase or 12-inch o.c.at 4-inch lap and SBS-SA,APP-
SC-62. 33 steel or min.2,500 psi layers,any Elastobase P with 12-inch o.c.at two,equally SBS-SA SA,SBS-TA or -60.0*
structrual concrete combination Attached poly top surface Bottom Plates(square) spaced,staggered center rows APP-TA
Min.22 ga.,type B,Grade One or more Elastobase or 12-inch o.c.at 4-inch lap and
Prelim. Roofgrip#12(steel only)or#14 with OMG Flat Polyflex SA
SC-63. 33 steel or min.2,500 psi layers,any Attached Elastobase P with Bottom Plates(square) 12-inch o.c.at two,equally Base APP-TA -60.0*
structrual concrete combination poly top surface spaced,staggered center rows
Min.22 ga.,type B,Grade One or more Loose 12-inch o.c.at 4-inch lap and
SC-64. 33 steel or min.2,500 psi layers,any Elastobase Trufast#12 DP(steel only),Plate#14 HD or#15 EHD with 12-inch o.c.at two,equally (Optional) ,APP-CAI SBS-
ai Trufast 3"Metal Insulation -67.5
structrual concrete combination ld spaced,staggered center rows CAI,SBS-CA2 SBS-CAI,
Min.22 ga.,type B,33 ksi One or more Trufast#15 EHD(steel only)or Trufast#14 HD 12-inch o.c.within the 5-inch
Prelim. (Optional)565- SBS-TA
SC-65. steel or min.2,500 psi layers,any Elastoflex S6 Type II (concrete only)with Trufast 2.75"Barbed Metal Seam wide,torch-sealed or heat- -82.5
structrual concrete combination Attached Plates welded side laps TA (D6164 only)
Trufast#15 EHD(steel only)or Trufast#14 HD
(concrete only)with Trufast 2.4"Barbed Metal Seam
Plates,Trufast 2.4"Scoop Seam Plates or Trufast
Min.22 ga.,type B,33 ksi One or more 12-inch o.c.within the 5-inch
Prelim. Polyglass HT Base 2.75"Barbed Metal Seam Plates or Dekfast#15 with (Optional)SBS- SBS-TA
SC-66. steel or min.2,500 psi layers,any wide,torch-sealed or heat- -82.5
structrual concrete combination Attached 650 Dekfast Galvalume Steel 1-1/2"x 2-3/4"Oval Barbed welded side laps TA (D6164 only)
Plate(aka,Dekfast PLT-02-3/4-12B)or Dekfast
Galvalume Steel 2-3/8"Round Barbed Plate(aka,
Dekfast PLT-R-2-3/8-6B)
Min.22 ga.,type B,Grade One or morePrelim. Dekfast#15 HS with Dekfast Galvalume Steel 2-3/8" 12-inch o.c.within the 5-inch (Optional)APP- SBS-TA,APP-
SC-67. 80 steel layers,any Attached Polyflex Round Barbed Plate(aka,Dekfast PLT-R-2-3/8-6B) wide,torch-sealed side lap TA TA 82.5
combination
Min.22 ga.,type B,Grade One or more Trufast#15 EHD(steel only)or Trufast#14 HD
Prelim. 12-inch o.c.within the 6-inch (Optional)APP- SBS-TA,APP-
SC-68. 80 steel or min.2,500 psi layers,any Attached Polybond or Polyflex (concrete only)with Trufast 2.4 in.Barbed Seam wide,torch-sealed side lap TA TA 82.5
structrual concrete combination Plates
Min.22 ga.,type B,40 ksi One or more Trufast#15 EHD(steel only)or Trufast#14 HD 6-inch o.c.within the 5-inch
Prelim. (Optional)SBS- SBS-TA
SC-69. steel or min.2,500 psi layers,any Elastoflex 56 Type II (concrete only)with Trufast 2.75"Barbed Metal Seam wide,torch-sealed or heat- -97.5
structrual concrete combination Attached Plates welded side laps TA (D6164 only)
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 30 of 58
QOTRINI-FY 'ERD
TABLE 2C: STEEL OR STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE D: PRELIMINARILY ATTACHED INSULATION,MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
NOTE: INSULATION IS OPTIONAL FOR RECOVER APPLICATIONS
System Deck Insulation Layer(s) Base Sheet Roof Cover(Note 15) MDP
No. (Note 1) Type Attach Type Fasten Attach Base Ply Cap Ply (psf)
Trufast#15 EHD(steel only)or Trufast#14 HD
(concrete only)with Trufast 2.4"Barbed Metal Seam
Plates,Trufast 2.4"Scoop Seam Plates or Trufast
Min.22 ga.,type B,40 ksi One or more 6-inch o.c.within the 5-inch
Prelim. Polyglass HT Base 2.75"Barbed Metal Seam Plates or Dekfast#15 with (Optional)SBS- SBS-TA
SC-70. steel or min.2,500 psi layers,any wide,torch-sealed or heat- -97.5
structrual concrete combination Attached 650 Dekfast Galvalume Steel 1-1/2"x 2-3/4"Oval Barbed welded side laps TA (D6164 only)
Plate(aka,Dekfast PLT-02-3/4-12B)or Dekfast
Galvalume Steel 2-3/8"Round Barbed Plate(aka,
Dekfast PLT-R-2-3/8-6B)
Min.22 ga.,type B,Grade One or more 12-inch o.c.at the 4-inch lap (Optional)BP-
Prelim. Dekfast#14 with Dekfast Hex(aka,Dekfast PLT-H-2- AA,SBS-AA, SBS-AA,SBS-
SC-71. t steel l min.2,500 psi layers any Attached Polybond,Polyflex 7/8)or OMG Roofgrip#14 OMG Flat Bottom Plates and 18-inch o.c.at two,equally SBS-TA or APP- TA,APP-TA 112.5
structrual concrete combination spaced,staggered center rows TA
Min.22 ga.,type B,Grade One or more Trufast#15 EHD(steel only)or Trufast#14 HD 6-inch o.c.within the 5-inch
Prelim. (Optional)SBS- SBS-TA
SC-72. 40 steel or min.2,500 psi layers,any Attached Elastoflex 56 Type II (concrete only)with Trufast 2.75"Barbed Metal Seam wide,torch-sealed or heat- TA (D6164 only) -135.0
structrual concrete combination Plates welded side laps
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 31 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Primer Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
SELF-ADHERING BASE WITH BASE INSULATION AND OPTIONAL TOP INSULATION OF THE SAME TYPE:
C-1 Structural (optional) Min.1.5-inch H-Shield or Multi-Max FA3 D-IS (Optional)additional layers(s)of D-IS SBS-SA (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, -67.5
concrete PG100 base insulation APP-TA SBS-TA,APP-TA
C 2 Structural (Optional) Min.1.5-inch H-Shield or Multi-Max FA3 D-IS (Optional)additional layers(s)of D-IS Polyflex SA (Optional)APP-TA APP-TA -67.5
concrete PG100 base insulation Base
Structural (Optional)additional layers(s)of SBS-SA or
C-3 None Min.1.5-inch Polytherm H,H-Shield D-IS D-IS Polyflex SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -122.5
concrete base insulation Base
Structural (Optional) Min (Optional)additional layers(s)of (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
C 4 concrete PG100 .1.5-inch Polytherm,ACFoam II or ENRGY 3 D-IS base insulation D-IS SBS-SA APP-TA SBS-TA,APP-TA 135.0
C-5 Structural (optional) Min.1.5-inch Polytherm,ACFoam II or ENRGY 3 D-IS (Optional)additional layers(s)of D-IS Polyflex SA (Optional)APP-TA APP-TA -135.0
concrete PG100 base insulation Base
C-6 Structural None Min.1.5-inch,min.1.5 pcf Insulfoam D-IS (Optional)additional layers of D-IS SBS-SA (Optional)SBS-SA SBS-SA,APP-SA -157.5
concrete base insulation
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, (Optional)additional layers of Polyflex SA
concrete ACFoam III,Polytherm H or H-Shield
C-7 None D-IS base insulation D-IS Base primed None SBS-SA,APP-SA -170.0
PRIMER:PG100 with PG100
C 8 Structural None Min.1.5-inch,min.2.0 pcf Insulfoam OB500 (Optional)additional layers of OB500 SBS-SA (Optional)SBS-SA SBS-SA,APP-SA -120.0
concrete base insulation
Structural (Optional)additional layers(s)of SBS-SA or
C-9 concrete None Min.1.5-inch Polytherm,ACFoam II OB500 base insulation OB500 Polyflex SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -122.5
Base
Structural (Optional)additional layers(s)of (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
C-10 concrete None Min.1.5-inch ENRGY 3 OB500 base insulation OB500 SBS-SA APP-TA SBS-TA,APP-TA 127.5
Structural (Optional)additional layers(s)of OB500 Polyflex SA 127.5 C-11 concrete None Min.1.5-inch ENRGY 3 OB500 base insulation Base (Optional)APP-TA APP-TA
Structural (Optional)additional layers(s)of (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
C-12 concrete None Min.1.5-inch Polytherm H or H-Shield OB500 base insulation OB500 SBS-SA APP-TA SBS-TA,APP-TA 150.0
Structural (Optional)additional layers(s)of Polyflex SA
C-13 concrete None Min.1.5-inch Polytherm H or H-Shield OB500 base insulation OB500 Base (Optional)APP-TA APP-TA 150.0
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, (Optional)additional layers of Polyflex SA
concrete ACFoam III,Polytherm H or H-Shield
C-14 None OB500 base insulation OB500 Base primed None SBS-SA,APP-SA -170.0
PRIMER:PG100 with PG100
Structural Min.1.5-inch Polytherm,ACFoam II,Polytherm M-OSFA or (Optional)additional layers(s)of M-OSFA or SBS-SA or
C-15 concrete None G,ACFoam III,Polytherm H,H-Shield M-PG1 base insulation M-PG1 Polyflex SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -122.5
Base
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL1654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 32 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Primer Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, M-OSFA or (Optional)additional layers of M-OSFA or Polyflex SA
M-PG1
C-16 None base insulation Base primed None SBS-SA,APP-SA -170.0
concrete ACFoam III,Polytherm H or H-Shield M-PG1 PRIMER:PG100 with PG100
Structural Min.1.5-inch Polytherm,ACFoam II, ENRGY 3, (Optional)additional layers(s)of (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
C-17 concrete None H-Shield or Multi-Max FA3 M-OSFA base insulation M-OSFA SBS-SA APP-TA SBS-TA,APP-TA 232.5
Structural Min.1.5-inch Polytherm,ACFoam II, ENRGY 3, (Optional)additional layers(s)of M-OSFA Polyflex SA 232.5 C-18 concrete None H-Shield or Multi-Max FA3 M-OSFA base insulation Base (Optional)APP-TA APP-TA
Min.1-inch Polytherm,ACFoam II,Polytherm G, (Optional)additional layers(s)of
Structural ACFoam III,EnergyGuard Polyiso Insulation, M-OSFA or M-OSFA or SBS-CA1,SBS-
C-19 concrete None ENRGY 3,Polytherm H,H-Shield,ISO 95+GL, M-PG1 base insulation,optionally M-PG1 SBS-SA None CA2 290.0
Multi-Max FA3,RESISTA or UltraMax. primed with WB-3000
Structural Min.1.5-inch Polytherm,ACFoam II,Polytherm (Optional)additional layers(s)of SBS-SA or
C-20 concrete None H,H-Shield CR-20 base insulation CR-20 Polyflex SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -122.5
Base
(Optional)additional layers of Polyflex SA
C-21 Structural None Min.1-inch Polytherm,ACFoam II,Polytherm G, CR-20 base insulation CR-20 Base primed None SBS-SA,APP-SA -170.0
concrete ACFoam III,Polytherm H or H-Shield
PRIMER:PG100 with PG100
Structural (Optional)additional layers of
C 22 concrete None Min.1.5-inch,min.2.0 pcf Insulfoam CR-20 base insulation CR-20 SBS-SA (Optional)SBS-SA SBS-SA,APP-SA 240.0
OB Classic OB Classic
Structural Min.2-inch Polytherm,ACFoam II,Polytherm H (full- (full- SBS-SA(Optional)additional layers(s)of (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
C-23 None -270.0
concrete or H-Shield coverage) coverage)base insulation APP-TA SBS-TA,APP-TA
OB Classic OB Classic
C-24 Structural None Min.2-inch Polytherm,ACFoam II,Polytherm H (full- (Optional)additional layers(s)of (full- Polyflex SA (Optional)APP-TA APP-TA -270.0
concrete or H-Shield coverage) coverage base insulation Base
)
Min.1.5-inch Polytherm,ACFoam Il,Polytherm
Structural Hot (Optional)additional layers(s)of Hot (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
C-25 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, asphalt base insulation asphalt SBS-SA APP-TA SBS-TA,APP-TA -480.0
H-Shield CG or Multi-Max FA3
Min.1.5-inch Polytherm,ACFoam II,Polytherm
Structural Hot (Optional)additional layers(s)of Hot Polyflex SA
C-26 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, asphalt base insulation asphalt Base (Optional)APP-TA APP-TA -480.0
H-Shield CG or Multi-Max FA3
SELF-ADHERING BASE WITH BASE INSULATION AND COVERBOARD:
Min.0.25-inch Dens Deck Prime
Structural (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
C 27 concrete None Min.1.5-inch Multi-Max FA3 D-IS or SECUROCK Gypsum-Fiber Roof D-IS SBS-SA APP-TA SBS-TA,APP-TA -67.5
Board
C 28 Structural None Min.1.5-inch Multi-Max FA3 D-IS Min.0.25-inch SECUROCK D-IS Polyflex SA (Optional)APP-TA APP-TA -67.5
concrete Gypsum-Fiber Roof Board Base
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6T'EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 33 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS-NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1 Primer Type Attach Type Attach Base Ply Ply Cap Ply (Psf)
Structural Min.1.5-inch,min.2.0 pcf Insulfoam,
C-29 concrete None Polytherm,ACFoam II,ENRGY 3,Polytherm H or D-IS Min.0.25-inch Dens Deck Prime D-IS SBS-SA (Optional)SBS-SA SBS-SA,APP-SA -72.5
H-Shield
C-30 Structural None Min.1.5-inch,min.2.0 pcf Insulfoam D-IS Min.0.25-inch Dens Deck,Dens D-IS SBS-SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -120.0
concrete Deck Prime
C-31 Structural None Min.1.5-inch,min.2.0 pcf Insulfoam D-IS Min.0.25-inch Dens Deck,Dens D-IS Polyflex SA (Optional)APP-TA APP-TA -120.0
concrete Deck Prime Base
Min.0.25-inch Dens Deck Prime,
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, DEXcell FA Glass Mat Roof Board Polyflex SA
C-32 None D-IS or SECUROCK Gypsum-Fiber Roof D-IS Base primed None SBS-SA,APP-SA -172.5
concrete ACFoam III,Polytherm H or H-Shield Board with PG100
PRIMER: PG100
C-33 Structural None Min.2-inch Polytherm,ACFoam II,ENRGY-3, D-IS Min.0.25-inch SECUROCK D-IS SBS-SA (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, 247 5
concrete Polytherm H or H-Shield Gypsum-Fiber Roof Board APP-TA SBS-TA,APP-TA
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch Dens Deck Prime
C-34 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield D-IS optionally primed with WB-3000 D-IS SBS-SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 282.5
Min.0.25-inch SECUROCK SBS-SA or
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, Gypsum-Fiber Roof Board or
C-35 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield D-IS DEXcell FA Glass Mat Roof Board D-IS Polyflex SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 322.5
Base
optionally primed with WB-3000
C-36 Structural None Min.1.5-inch Polytherm,ACFoam II,ENRGY 3, OB500 Min.0.25-inch Dens Deck Prime OB500 SBS-SA
concrete H-Shield or ISO 95+GL (Optional)SBS-SA 565-SA,APP-SA 72.5
C-37 Structural None Min.1.5-inch ENRGY 3 OB500 Min.0.25-inch Dens Deck,Dens OB500 SBS-SA
concrete Deck Prime (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 127.5
C-38 Structural None Min.1.5-inch ENRGY 3 OB500 Min.0.25-inch Dens Deck,Dens OB500 Polyflex SA (Optional)APP-TA APP-TA -127.5
concrete Deck Prime Base
C-39 Structural None Min.1.5-inch Polytherm,ACFoam II,H-Shield or OB500 Min.0.25-inch Dens Deck,Dens OB500 SBS-SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -150.0
concrete ISO 95+GL Deck Prime
C-40 Structural None Min.1.5-inch Polytherm,ACFoam II,H-Shield or OB500 Min.0.25-inch Dens Deck,Dens OB500 Polyflex SA (Optional)APP-TA APP-TA -150.0
concrete ISO 95+GL Deck Prime Base
Min.0.25-inch Dens Deck Prime,
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, DEXcell FA Glass Mat Roof Board Polyflex SA
C-41 None OB500 or SECUROCK Gypsum-Fiber Roof OB500 Base primed None SBS-SA,APP-SA -172.5
concrete ACFoam III,Polytherm H or H-Shield Board with PG100
PRIMER: PG100
C 42 Structural None Min.2-inch Polytherm,ACFoam II,ENRGY-3, OB500 Min.0.25-inch SECUROCK OB500 SBS-SA (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, _247.5
concrete Polytherm H or H-Shield Gypsum-Fiber Roof Board APP-TA SBS-TA,APP-TA
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II,
C-43 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield OB500 Min.0.25-inch Dens Deck Prime OB500 SBS-SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 282.5
Exterior Research and Design,I.I.C.d/b/a Trinity)ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 34 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS-NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1 Primer Type Attach Type Attach Base Ply Ply Cap Ply (Psf)
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK SBS-SA or
C 44 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield OB500 Gypsum-Fiber Roof Board or OB500 Polyflex SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -322.5
DEXcell FA Glass Mat Roof Board Base
C-45 Structural None Min.1.5-inch Polytherm,ACFoam II,ENRGY 3, M-OSFA Min.0.25-inch Dens Deck Prime M-OSFA SBS-SA (Optional)SBS-SA SBS-SA,APP-SA -72.5
concrete H-Shield or Multi-Max FA3
Min.0.25-inch Dens Deck Prime,
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, M-OSFA or DEXcell FA Glass Mat Roof Board M-OSFA or Polyflex SA
M-PG1
C-46 None or SECUROCK Gypsum-Fiber Roof Base primed None SBS-SA,APP-SA -172.5
concrete ACFoam III,Polytherm H or H-Shield M-PG1 Board with PG100
PRIMER: PG100
C 47 Structural None Min.1.5-inch Polytherm,ACFoam II,ENRGY 3, M-OSFA Min.0.25-inch SECUROCK M-OSFA SBS-SA (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, _232.5
concrete H-Shield or Multi-Max FA3 Gypsum-Fiber Roof Board APP-TA SBS-TA,APP-TA
C 48 Structural None Min.2-inch Polytherm,ACFoam II,ENRGY-3, M-OSFA Min.0.25-inch SECUROCK M-OSFA SBS-SA (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, 247 5
concrete Polytherm H or H-Shield Gypsum-Fiber Roof Board APP-TA SBS-TA,APP-TA
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, M-OSFA or M-OSFA or
C 49 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield M-PG1 Min.0.25-inch Dens Deck Prime M-PG1 SBS-SA (Optional)SBS-TA,APP-TA 565-TA,APP-TA 282.5
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, M-OSFA or Min.0.25-inch SECUROCK M-OSFA or SBS-SA or
C-50 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield M-PG1 Gypsum-Fiber Roof Board or M-PG1 Polyflex SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -322.5
DEXcell FA Glass Mat Roof Board Base
Min.1.5-inch,min.2.0 pcf Insulfoam,Min.2-
inch Polytherm,ACFoam II, min.1.5-inch Ultra-
C-51 Structural None Max or Multi-Max FA-3,min.1.3-inch CR-20 Min.0.25-inch Dens Deck,Dens CR-20 SBS-SA (Optional)SBS-SA SBS-SA,APP-SA -72.5
concrete Polytherm G,ACFoam III or min.1.0-inch ISO Deck Prime
95+GL,Polytherm H,H-Shield,H-Shield CG or
ENRGY 3
Min.0.25-inch Dens Deck Prime,
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, DEXcell FA Glass Mat Roof Board Polyflex SA
C-52 None CR-20 or SECUROCK Gypsum-Fiber Roof CR-20 Base primed None SBS-SA,APP-SA -172.5
concrete ACFoam III,Polytherm H or H-Shield Board with PG100
PRIMER: PG100
Min.1.5-inch,min.2.0 pcf Insulfoam,Min.1.5-
inch Ultra-Max or Multi-Max FA-3,min.1.3-inch
C-53 Structural None Polytherm G,ACFoam III or min.1.0-inch ISO CR-20 Min.0.25-inch Dens Deck,Dens CR-20 SBS-SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -240.0
concrete 95+GL,Polytherm H,H-Shield,H-Shield CG or Deck Prime
ENRGY 3
Min.1.5-inch,min.2.0 pcf Insulfoam,Min.1.5-
inch Ultra-Max or Multi-Max FA-3,min.1.3-inch
C-54 Structural None Polytherm G,ACFoam III or min.1.0-inch ISO CR-20 Min.0.25-inch Dens Deck,Dens CR-20 Polyflex SA (Optional)APP-TA APP-TA -240.0
concrete 95+GL,Polytherm H,H-Shield,H-Shield CG or Deck Prime Base
ENRGY 3
Exterior Research and Design,I.I.C.d/b/a Trinity)ERD Evaluation Report P9290.02.08-R20 for FL1654-R22
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 35 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS-NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Primer Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
Min.1.5-inch Ultra-Max or Multi-Max FA-3,
C-55 Structural None min.1.3-inch Polytherm G,ACFoam III or min. CR-20 Min.0.25-inch SECUROCK CR-20 SBS-SA (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, -240.0
concrete 1.0-inch ISO 95+GL,Polytherm H,H-Shield,H- Gypsum-Fiber Roof Board APP-TA SBS-TA,APP-TA
Shield CG or ENRGY 3
Min.1.5-inch Ultra-Max or Multi-Max FA-3,
C-56 Structural None min.1.3-inch Polytherm G,ACFoam III or min. CR-20 Min.0.25-inch SECUROCK CR-20 Polyflex SA (Optional)APP-TA APP-TA -240.0
concrete 1.0-inch ISO 95+GL,Polytherm H,H-Shield,H- Gypsum-Fiber Roof Board Base
Shield CG or ENRGY 3
C-57 Structural None Min.2-inch Polytherm,ACFoam II,ENRGY-3, CR-20 Min.0.25-inch SECUROCK CR-20 SBS-SA (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, 247 5
concrete Polytherm H or H-Shield Gypsum-Fiber Roof Board APP-TA SBS-TA,APP-TA
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II,
C-58 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield CR-20 Min.0.25-inch Dens Deck Prime CR-20 SBS-SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 282.5
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK SBS-SA or
C-59 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield CR-20 Gypsum-Fiber Roof Board or CR-20 Polyflex SA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -322.5
DEXcell FA Glass Mat Roof Board Base
Structural Min.2-inch Polytherm,ACFoam II,Polytherm H OB Classic Min.0.25-inch SECUROCK OB Classic (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
concrete or H-Shield Gypsum-Fiber Roof Board APP-TA SBS-TA,APP-TA
C-60 None (full- (full- SBS-SA -350.0
coverage) coverage)
Structural Min.2-inch Polytherm,ACFoam II,Polytherm H OB Classic Min.0.25-inch SECUROCK OB ClassicPolyflex SA
C-61 concrete None or H-Shield (full- Gypsum-Fiber Roof Board (full- Base (Optional)APP-TA APP-TA -350.0
coverage) coverage)
Min.1.5-inch Polytherm,ACFoam II,Polytherm
Structural Hot Min.0.25-inch SECUROCK Hot (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
C-62 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, asphalt Gypsum-Fiber Roof Board asphalt SBS-SA APP-TA SBS-TA,APP-TA -350.0
H-Shield CG or Multi-Max FA3
Structural Min.1.5-inch Polytherm,ACFoam II,Polytherm Hot Min.0.25-inch SECUROCK Hot Polyflex SA
C-63 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, asphalt Gypsum-Fiber Roof Board asphalt Base (Optional)APP-TA APP-TA -350.0
H-Shield CG or Multi-Max FA3
ASPHALT OR TORCH APPLIED BASE:
C-64 Structural None Min.2-inch Polytherm,ACFoam II,Polytherm H D-IS Min.0.25-inch SECUROCK D-IS BP-AA,SBS-AA (Optional)BP-AA,SBS-AA SBS-AA -225.0
concrete or H-Shield Gypsum-Fiber Roof Board
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II,
C-65 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield D-IS Min.0.25-inch Dens Deck Prime D-IS SBS-TA,APP-TA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 282.5
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK
C-66 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield D-IS Gypsum-Fiber Roof Board or D-IS SBS-TA,APP-TA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -322.5
DEXcell FA Glass Mat Roof Board
C-67 Structural None Min.2-inch Polytherm,ACFoam II,Polytherm H OB500 Min.0.25-inch SECUROCK OB500 BP-AA,SBS-AA (Optional)BP-AA,SBS-AA SBS-AA -225.0
concrete or H-Shield Gypsum-Fiber Roof Board
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II,
C-68 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield OB500 Min.0.25-inch Dens Deck Prime OB500 SBS-TA,APP-TA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 282.5
Exterior Research and Design,I.I.C.d/b/a Trinity(ERD Evaluation Report P9290.02.08-1120 for FL3654-1122
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 36 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS-NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1 Primer Type Attach Type Attach Base Ply Ply Cap Ply (Psf)
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK
C-69 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield OB500 Gypsum-Fiber Roof Board or OB500 SBS-TA,APP-TA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -322.5
DEXcell FA Glass Mat Roof Board
Structural None Min.2-inch Polytherm,ACFoam II,Polytherm H M-OSFA or Min.0.25-inch SECUROCK M-OSFA or 225.0 C-70 concrete or H-Shield M-PG1 Gypsum-Fiber Roof Board M-PG1 BP-AA,SBS-AA (Optional)BP-AA,SBS-AA SBS-AA
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, M-OSFA or M-OSFA or
C-71 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield M-PG1 Min.0.25-inch Dens Deck Prime M-PG1 SBS-TA,APP-TA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 282.5
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, M-OSFA or Min.0.25-inch SECUROCK M-OSFA or
C 72 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield M-PG1 Gypsum-Fiber Roof Board or M-PG1 SBS-TA,APP-TA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -322.5
DEXcell FA Glass Mat Roof Board
Min.1.5-inch Ultra-Max or Multi-Max FA-3,
C-73 Structural None min.1.3-inch Polytherm G,ACFoam III or min. CR-20 Min.0.25-inch SECUROCK CR-20 BP-AA,SBS-AA (Optional)BP-AA,SBS-AA SBS-AA -225.0
concrete 1.0-inch ISO 95+GL,Polytherm H,H-Shield,H- Gypsum-Fiber Roof Board
Shield CG or ENRGY 3
Min.1.5-inch Ultra-Max or Multi-Max FA-3,
C 74 Structural None min.1.3-inch Polytherm G,ACFoam III or min. CR-20 Min.0.25-inch SECUROCK CR-20 APP-TA (Optional)APP-TA APP-TA -232.5
concrete 1.0-inch ISO 95+GL,Polytherm H,H-Shield,H- Gypsum-Fiber Roof Board
Shield CG or ENRGY 3
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II,
C-75 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield CR-20 Min.0.25-inch Dens Deck Prime CR-20 SBS-TA,APP-TA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA 282.5
Structural (Optional)Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK
C-76 concrete None Polytherm G,ACFoam III,Polytherm H,H-Shield CR-20 Gypsum-Fiber Roof Board or CR-20 SBS-TA,APP-TA (Optional)SBS-TA,APP-TA SBS-TA,APP-TA -322.5
DEXcell FA Glass Mat Roof Board
Structural (Optional)Min.2-inch Polytherm,ACFoam II, OB Classic Min.0.25-inch SECUROCK OB Classic
C-77 concrete Polytherm H or H-Shield Gypsum-Fiber Roof Board None (full- (full- BP-AA,SBS-AA (Optional)BP-AA,SBS-AA SBS-AA -225.0
coverage) coverage)
OB Classic OB Classic
C 78 Structural None (Optional)Min.2-inch Polytherm,ACFoam II, (full- Min.um-Finch Roof
Board
(full- APP-TA (Optional)APP-TA APP-TA -232.5
concrete Polytherm H or H-Shield Gypsum-Fiber Roof Board
coverage) coverage)
Structural Min.1.5-inch Polytherm,ACFoam II,Polytherm Hot Min.0.25-inch SECUROCK Hot
C 79 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, asphalt Gypsum-Fiber Roof Board asphalt BP-AA,SBS-AA (Optional)BP-AA,SBS-AA SBS-AA -225.0
H-Shield CG or Multi-Max FA3
Structural Min.1.5-inch Polytherm,ACFoam II,Polytherm Hot Min.0.25-inch SECUROCK Hot
C-80 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, asphalt Gypsum-Fiber Roof Board asphalt APP-TA (Optional)APP-TA APP-TA -232.5
H-Shield CG or Multi-Max FA3
(Optional if (Optional if using AA Base)
Structural Hot SBS-AA,SBS-TA,
C-81 concrete PG100 Min.0.75-inch Fesco Board(homogeneous) asphalt None N/A using AA Ply) BP-AA,SBS-AA,SBS-TA or APP TA -277.5
BP-AA,SBS-AA APP-TA
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 37 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1 Primer Type Attach Type Attach Base Ply Ply Cap Ply (Psf)
Min.1.5-inch Polytherm,ACFoam II,Polytherm (Optional if (Optional if using AA Base)
Structural Hot Min.0.75-inch Fesco Board Hot SBS-AA,SBS-TA,
C 82 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, asphalt (homogeneous) asphalt using AA Ply) BP-AA,SBS-AA,SBS-TA or APP TA -290.0
H-Shield CG or Multi-Max FA3 BP-AA,SBS-AA APP-TA
Structural Min.0.5-inch Structodek High Density Hot (Optional if (Optional if using AA Base) SBS-AA,SBS-TA,
C-83 concrete PG100 Fiberboard Roof Insulation asphalt None N/A using AA Ply) BP-AA,SBS-AA,SBS-TA or APP TA -285.0
BP-AA,SBS-AA APP-TA
Min.1.5-inch Polytherm,ACFoam II,Polytherm Min.0.5-inch Structodek High (Optional if (Optional if using AA Base)
Structural Hot Hot SBS-AA,SBS-TA,
C 84 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, asphalt Density Fiberboard Roof asphalt using AA Ply) BP-AA,SBS-AA,SBS-TA or APP TA -480.0
H-Shield CG or Multi-Max FA3 Insulation BP-AA,SBS-AA APP-TA
Min.1.5-inch Polytherm,ACFoam II,Polytherm (Optional if (Optional if using AA Base)
Structural Hot Hot SBS-AA,SBS-TA,
C-85 concrete PG100 G,ACFoam III,ENRGY 3,Polytherm H,H-Shield, halt Min.0.25-inch Dens Deck Prime asphalt using AA Ply) BP-AA,SBS-AA,SBS-TA or APP TA -480.0
asp
H-Shield CG or Multi-Max FA3 BP-AA,SBS-AA APP-TA
(Optional if (Optional if using AA Base)
Structural Hot SBS-AA,SBS-TA,
C-86 concrete PG100 Min.0.25-inch Dens Deck Prime asphalt None N/A using AA Ply) BP-AA,SBS-AA,SBS-TA or APP TA -510.0
BP-AA,SBS-AA APP-TA
COLD-APPLIED BASE:
Min.0.25-inch Dens Deck Prime,
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, DEXcell FA Glass Mat Roof Board SBS-CA1,SBS- (Optional)SBS-CA1,SBS- SBS-CA1,SBS-
C 87 concrete None ACFoam III,ENRGY 3,Polytherm H or H-Shield D-IS or SECUROCK Gypsum-Fiber Roof D-IS CA2 CA2 CA2,APP-CA1 120.0
Board
Min.0.25-inch Dens Deck Prime
C 88 Structural None Min.am III,Polytherm,ACFoam II,Polytherm G, D-IS or DEXcell FA Glass Mat Roof D-IS SBS-CA1 None CA2,A 1,SBS- -127.5
concrete ACFoam III,Polytherm H or H-Shield Board CA2,APP-CAl
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, D-IS Min.0.25-inch SECUROCK D-IS SBS-CAI,SBS- None SBS-CA1,SBS-
127.5
C-89 concrete None ACFoam III,Polytherm H or H-Shield Gypsum-Fiber Roof Board CA2 CA2,APP-CA1
Min.0.25-inch Dens Deck Prime
Structural SBS-CAI,SBS- SBS-CA1,565-
C-90 concrete None Min.1-inch ENRGY 3,Polytherm H or H-Shield D-IS or SECUROCK Gypsum-Fiber Roof D-IS CA2 None CA2 -232.5
Board
Min.0.25-inch Dens Deck,Dens
Deck Prime,DEXcell FA Glass
Min.1-inch Polytherm,ACFoam II,Polytherm G, Mat Roof Board,SECUROCK
M-OSFA,Structural
ACFoam III,EnergyGuard Polyiso Insulation, Gypsum-Fiber Roof Board or M-OSFA or SBS-CAl,SBS- (Optional)SBS-CA1,SBS- SBS-CA1,SBS-
C-91 concrete None ENRGY 3,Polytherm H,H-Shield ISO 95+GL, M-PG1 SECUROCK Glass-Mat Roof M-PG1 CA2 CA2 CA2,APP-CA1 -120.0
Multi-Max FA3,RESISTA or UltraMax or min.2- Board,min.7/16-inch DEXcell
inch DECKMATE Plus or DECKMATE Plus FA Cement Roof Board or min.0.5-
inch SECUROCK Cement Roof
Board
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 38 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Primer Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
Min.1-inch Polytherm or ACFoam II,Polytherm Min.0.25-inch Dens Deck Prime
G,ACFoam III,EnergyGuard Polyiso Insulation, or DEXcell FA Glass Mat Roof
Structural M-OSFA, Board,min.7/16-inch DEXcell M-OSFA, SBS-CA1,SBS
C 92 concrete None ENRGY 3,Polytherm H,H-Shield,I50 95+ n. M-PG1 Cement Roof Board or min.0.5- M-PGl SBS-CA1 None CA2,APP-CA1 127.5
Multi-Max FA3,RESISTA or UltraMax or min.2-
inch DECKMATE Plus or DECKMATE Plus FA inch SECUROCK Cement Roof
Board
Min.1-inch Polytherm or ACFoam II,Polytherm
G,ACFoam III,EnergyGuard Polyiso Insulation,
Structural M-OSFA, Min.0.25-inch SECUROCK M-OSFA, SBS-CA1,SBS- SBS-CA1,565-
C-93 concrete None ENRGY 3,Polytherm H,H-Shield,ISO 95+GL, M-PG1 Gypsum-Fiber Roof Board M-PG1 CA2 None CA2,APP-CA1 -127.5
Multi-Max FA3,RESISTA or UltraMax or min.2-
inch DECKMATE Plus or DECKMATE Plus FA
Min.0.25-inch Dens Deck,Dens
Deck Prime,DEXcell FA Glass
Min.1-inch Polytherm or ACFoam II,Polytherm Mat Roof Board,SECUROCK
G,ACFoam III,EnergyGuard Polyiso Insulation, Gypsum-Fiber Roof Board or
Structural M-OSFA, M-OSFA, SBS-CAl,SBS- SBS-CAl,SBS-
C 94 concrete None ENRGY 3,Polytherm H,H-Shield,ISO 95+GL, M-PG1 SECUROCK Glass-Mat Roof M-PG1 CA2 None CA2 -232.5
Multi-Max FA3,RESISTA or UltraMax or min.2- Board,min.7/16-inch DEXcell
inch DECKMATE Plus or DECKMATE Plus FA Cement Roof Board or min.0.5-
inch SECUROCK Cement Roof
Board
Min.1-inch Polytherm,ACFoam II,Polytherm G, Min.0.25-inch Dens Deck Prime,
Structural DEXcell FA Glass Mat Roof Board SBS-CAI,SBS- (Optional)SBS-CA1,SBS- SBS-CA1,SBS-
C-95 concrete None ACFoam III,ENRGY 3,Polytherm H,H-Shield or OB500 or SECUROCK Gypsum-Fiber Roof OB500 CA2 CA2 CA2,APP-CA1 120.0
Multi-Max FA3
Board
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, Min.0.25-inch Dens Deck Prime SBS-CA1,SBS-
C-96 concrete None ACFoam III,ENRGY 3,Polytherm H,H-Shield or OB500 or DEXcell FA Glass Mat Roof OB500 SBS-CA1 None CA2,APP-CA1 -127.5
Multi-Max FA3 Board
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, Min.0.25-inch SECUROCK SBS-CA1,SBS- SBS-CA1,SBS-
C-97 concrete None ACFoam III,ENRGY 3,Polytherm H,H-Shield or OB500 Gypsum-Fiber Roof Board OB500 CA2 None CA2,APP-CA1 -127.5
Multi-Max FA3
Min.0.25-inch Dens Deck Prime,
Structural Min.1-inch Polytherm,ACFoam II,ENRGY 3 or OB500 DEXcell FA Glass Mat Roof Board SBS-CA1,SBS- None SBS-CA1,SBS-
232.5
C-98 concrete None Multi-Max FA3 or SECUROCK Gypsum-Fiber Roof OB500 CA2 CA2
Board
Structural
Min.1-inch Polytherm,ACFoam II,Polytherm G, Min.0.25-inch Dens Deck Prime SBS-CAl,SBS- (Optional)SBS-CA1,SBS- SBS-CA1,SBS-
C 99 concrete None ACFoam III,ENRGY 3,Polytherm H,H-Shield or CR-20 or SECUROCK Gypsum-Fiber Roof CR-20 CA2 CA2 CA2,APP-CA1 -120.0
Multi-Max FA3 Board
Min.1-inch Polytherm,ACFoam II,Polytherm G, Min.0.25-inch Dens Deck Prime
C-100 Structural None ACFoam III,ENRGY 3,Polytherm H,H-Shield or CR-20 or DEXcell FA Glass Mat Roof CR-20 SBS-CA1 None SBS CA2,,APP-CAl SBS-
concrete -127.5
Multi-Max FA3 Board
Exterior Research and Design,I.I.C.d/b/a Trinity)ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 39 of 58
QO
TRINITY ERD
TABLE 3A: STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
NOTE: FOR VAPOR BARRIER OPTIONS REFER TO NOTE 18
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Note 1 Primer Type Attach Type Attach Base Ply Ply Cap Ply (Psf)
Structural Min.1-inch Polytherm,ACFoam II,Polytherm G, Min.0.25-inch SECUROCK SBS-CA1,SBS- SBS-CA1,SBS-
C-101 concrete None ACFoam III,ENRGY 3,Polytherm H,H-Shield or CR-20 Gypsum-Fiber Roof Board CR-20 CA2 None CA2,APP-CA1 -127.5
Multi-Max FA3
Structural Min.1-inch ENRGY 3,Polytherm H,H-Shield, Min.0.25-inch Dens Deck Prime SBS-CAl,565- SBS-CA1,SBS-
C-102 concrete None Multi-Max FA3 CR-20 or SECUROCK Gypsum-Fiber Roof CR-20 CA2 None CA2 -232.5
Board
TABLE 3B: STRUCTURAL CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE F:NON-INSULATED,BONDED BASE SHEET,BONDED ROOF COVER
System Deck Primer Roof Cover(Note 15) MDP(psf)
No. (Note 1) Base Ply Ply Cap Ply
C-103 Structural concrete None SBS-CA1 None SBS-CA1,SBS-CA2,APP-CA1 -105.0
C-104 Structural concrete PG100 Polyflex SA Base primed with PG100 None SBS-SA,APP-SA -117.5
C-105 Structural concrete PG100 SBS-SA (Optional)SBS-SA,SBS-TA,APP-TA SBS-SA,APP-SA,SBS-TA,APP-TA -315.0
C-106 Structural concrete PG100 Polyflex SA Base (Optional)APP-TA APP-TA -315.0
C-107 Structural concrete PG100 (Optional)SBS-TA (Optional)SBS-TA SBS-TA -495.0
C-108 Structural concrete PG100 BP-AA(Optional if using asphalt applied Ply) (Optional if using asphalt applied Base)BP-AA,SBS- SBS-AA,SBS-TA,APP-TA -622.5
AA,SBS-TA or APP-TA
Exterior Research and Design,I.I.C.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6t"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 40 of 58
Q0
TRINITY ERD
TABLE 4A: LIGHTWEIGHT CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1: BONDED INSULATION,BONDED ROOF COVER
System Deck Lightweight Base Insulation Layer Coverboard Roof Cover(Note 15) MDP
No. (Note 1) Concrete(Note 14) Type Attach Type Attach Base Ply Ply Cap Ply (pso
SELF-ADHERING BASE WITH BASE INSULATION AND OPTIONALTOP INSULATION OFTHE SAME TYPE:
Structural Min.200 psi,min (Optional)Additional layers
LWC-1 concrete 2-inch Elastizell Min.1.5-inch,min.2.0 pcf Insulfoam OB500 of base insulation OB500 SBS-SA (Optional)SBS-SA SBS-SA,APP-SA 120.0
Structural Min.200 psi,min Min.1.5-inch Polytherm,ACFoam II,ENRGY OB500 (Optional)Additional layers OB500 SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, 225.0
LWC-2 concrete 2-inch Elastizell 3,ISO 95+GL,Polytherm H or H-Shield of base insulation TA,APP-TA SBS-TA,APP-TA
Structural Min.200 psi,min Min.1.5-inch Polytherm,ACFoam II,ENRGY OB500 (Optional)Additional layers OB500 Polyflex SA 225.0 LWC-3 concrete 2-inch Elastizell 3,ISO 95+GL,Polytherm H or H-Shield of base insulation Base (Optional)APP-TA APP-TA
Structural Min.200 psi,min. (Optional)Additional layers
LWC-4 concrete 2-inch Elastizell Min.1.5-inch,min.2.0 pcf Insulfoam CR-20 of base insulation CR-20 SBS-SA (Optional)SBS-SA SBS-SA,APP-SA 180.0
Min.1.5-inch Polytherm,ACFoam II,
Structural Min.200 psi,min. Polytherm G,ACFoam III,ENRGY 3,ISO 95+ CR-20 (Optional)Additional layers CR-20 SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, 180.0
LWC-5 concrete 2-inch Elastizell GL,Polytherm H,H-Shield,H-Shield CG, of base insulation TA,APP-TA SBS-TA,APP-TA
Multi-Max FA3
Min.1.5-inch Polytherm,ACFoam II,
Structural Min.200 psi,min. Polytherm G,ACFoam III,ENRGY 3,ISO 95+ CR-20 (Optional)Additional layers CR-20 Polyflex SA 180.0 LWC-6 concrete 2-inch Elastizell GL,Polytherm H,H-Shield,H-Shield CG, of base insulation Base (Optional)APP-TA APP-TA
Multi-Max FA3
Min.200 psi,min.
Structural (Optional)Additional layers
LWC-7 concrete 2-inch Celcore or Min.1.5-inch,min.2.0 pcf Insulfoam CR-20 of base insulation CR-20 SBS-SA (Optional)SBS-SA SBS-SA,APP-SA -222.5
Mearlcrete
Min.200 psi,min.
Min.1.5-inch Polytherm,ACFoam II,
Structural Polytherm G,ACFoam III,ENRGY 3,ISO 95+ (Optional)Additional layers (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
LWC-8 concrete MearI crete Celcore or GL,Polytherm H,H-Shield,H-Shield CG, CR-20 of base insulation CR-20 SBS-SA TA,APP-TA SBS-TA,APP-TA 222.5
earl Multi-Max FA3
Min.200 psi,min.
Min.1.5-inch Polytherm,ACFoam II,
Structural Polytherm G,ACFoam III,ENRGY 3,ISO 95+ (Optional)Additional layers Polyflex SA
LWC-9 concrete MearI crete Celcore or GL,Polytherm H,H-Shield,H-Shield CG, CR-20 of base insulation CR-20 Base (Optional)APP-TA APP-TA 222.5
earl Multi-Max FA3
SELF-ADHERING BASE WITH BASE INSULATION AND COVERBOARD:
LWC-10 Structural Min.200 psi,min Min.1.5-inch,min.2.0 pcf Insulfoam OB500 Min.0.25-inch SECUROCK OB500 SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, -120.0
concrete 2-inch Elastizell Gypsum-Fiber Roof Board TA,APP-TA SBS-TA,APP-TA
LWC-11 Structural Min.200 psi,min Min.1.5-inch,min.2.0 pcf Insulfoam OB500 Min.0.25-inch SECUROCK OB500 Polyflex SA (Optional)APP-TA APP-TA -120.0
concrete 2-inch Elastizell Gypsum-Fiber Roof Board Base
Structural Min.200 psi,min Min.1.5-inch Polytherm,ACFoam II,ENRGY OB500 Min.0.25-inch SECUROCK OB500 SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, 225.0
LWC-12 concrete 2-inch Elastizell 3,ISO 95+GL,Polytherm H or H-Shield Gypsum-Fiber Roof Board TA,APP-TA SBS-TA,APP-TA
LWC-13 Structural Min.200 psi,min Min.1.5-inch Polytherm,ACFoam II,ENRGY OB500 Min.0.25-inch SECUROCK OB500 Polyflex SA (Optional)APP-TA APP-TA -225.0
concrete 2-inch Elastizell 3,ISO 95+GL,Polytherm H or H-Shield Gypsum-Fiber Roof Board Base
Exterior Research and Design,I.I.C.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6TR EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 41 of 58
QO
TRINITY ERD
TABLE 4A: LIGHTWEIGHT CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1: BONDED INSULATION,BONDED ROOF COVER
System Deck Lightweight Base Insulation Layer Coverboard Roof Cover(Note 15) MOP
No. (Note 1) Concrete(Note 14) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
Min.1.5-inch Polytherm,ACFoam II,
Structural Min.200 psi,min. Polytherm G,ACFoam III,ENRGY 3,ISO 95+ CR 20 Min.0.25-inch SECUROCK CR-20 SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, 180.0
LWC-14 concrete 2-inch Elastizell GL,Polytherm H,H-Shield,H-Shield CG, Gypsum-Fiber Roof Board TA,APP-TA SBS-TA,APP-TA
Multi-Max FA3 or min.2.0 pcf Insulfoam
Min.1.5-inch Polytherm,ACFoam II,
Structural Min.200 psi,min. Polytherm G,ACFoam III,ENRGY 3,ISO 95+ CR 20 Min.0.25-inch SECUROCK Polyflex SA 180.0 LWC-15 concrete 2-inch Elastizell GL,Polytherm H,H-Shield,H-Shield CG, Gypsum-Fiber Roof Board CR 20 Base (Optional)APP-TA APP-TA
Multi-Max FA3 or min.2.0 pcf Insulfoam
Min.200 psi,min.
Min.1.5-inch Polytherm,ACFoam II,
Structural Polytherm G,ACFoam III,ENRGY 3,ISO 95+ Min.0.25-inch SECUROCK (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
LWC-16 concrete MearI crete Celcore or GL,Polytherm H,H-Shield,H-Shield CG, CR-20 Gypsum-Fiber Roof Board CR-20 SBS-SA TA,APP-TA SBS-TA,APP-TA 222.5
earl Multi-Max FA3 or min.2.0 pcf Insulfoam
Min.200 psi,min.
Min.1.5-inch Polytherm,ACFoam II,
Structural Polytherm G,ACFoam III,ENRGY 3,ISO 95+ Min.0.25-inch SECUROCK Polyflex SA
LWC-17 concrete MearI crete Celcore or GL,Polytherm H,H-Shield,H-Shield CG, CR-20 Gypsum-Fiber Roof Board CR-20 Base (Optional)APP-TA APP-TA 222.5
earl Multi-Max FA3 or min.2.0 pcf Insulfoam
ASPHALT OR TORCH APPLIED BASE:
LWC-18 Structural Min.200 psi,min Min.1.5-inch Polytherm,ACFoam II,ENRGY OB500 Min.0.25-inch SECUROCK OB500 BP-AA,SBS- (Optional)BP-AA,SBS- SBS-AA,SBS-TA, -225.0
concrete 2-inch Elastizell 3,ISO 95+GL,Polytherm H or H-Shield Gypsum-Fiber Roof Board AA,APP-TA AA,SBS-TA or APP-TA APP-TA
Min.1.5-inch Polytherm,ACFoam II,
LWC-19 Structural Min.200 psi,min. Polytherm G,ACFoam III,ENRGY 3,ISO 95+ CR-20 Min.0.25-inch SECUROCK CR-20 BP-AA,SBS- (Optional)BP-AA,SBS- SBS-AA,SBS-TA, -180.0
concrete 2-inch Elastizell GL,Polytherm H,H-Shield,H-Shield CG, Gypsum-Fiber Roof Board AA,APP-TA AA,SBS-TA or APP-TA APP-TA
Multi-Max FA3 or min.2.0 pcf Insulfoam
Min.200 psi,min.
Min.1.5-inch Polytherm,ACFoam II,
Structural Polytherm G,ACFoam III,ENRGY 3,ISO 95+ Min.0.25-inch SECUROCK BP-AA,SBS- (Optional)BP-AA,SBS- SBS-AA,SBS-TA,
LWC-20 concrete MearI crete Celcore or GL,Polytherm H,H-Shield,H-Shield CG, CR-20 Gypsum-Fiber Roof Board CR-20 AA,APP-TA AA,SBS-TA or APP-TA APP-TA 222.5
earl Multi-Max FA3 or min.2.0 pcf Insulfoam
Exterior Research and Design,I.I.C.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 42 of 58
QO
TRINITY ERD
TABLE 4B: LIGHTWEIGHT CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
Lightweight Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15)
System Deck(Note 1) Concrete T T MDP
(Note 14) Type Fasten Attach Type Attach Type Attach Base Ply Ply Cap Ply (psf)
(Optional)Min.1.5- Min.1.5-inch Thermaroof
Min.22 ga., inch Polytherm, (Optional if
7-inch o.c.at 4- Composite,Polytherm (Optional if
GAFGLAS
Min.300 psi inch lap and 7- Composite,or min.0.5-inch using AA SBS-AA,
B
steel at max.5 ft
LWC-21 Type B,vented Approved SF CR inch o.c.in two, Shield Multi-ACFoam Il,Polytherm HA Structodek High Density HA using Ply)BP
SBS AA- Base)BP-AA, SBS-TA, -45.0
cellular LWC #75 SF equally spaced H, x FA3 , Fiberboard Roof Insulation or AA, SBS-AA,SBS- APP-TA
spans center rows Max or min.0.75-inch Fesco Board TA or APP-TA
Polytherm (homogeneous)
7-inch o.c.at 4- Min.1.5-inch
Min.22 ga., SBS-SA,
Min.300 psi GAFGLAS inch lap and 7- Polytherm,ACFoam (Optional)
LWC-22 Type B,vented Approved SF CR inch o.c.in two, II,Polytherm H,H- HA None N/A SBS-SA SBS-SA,SBS- APP SA,
B -45.0
steel at max.5 ft cellular LWC #75 SF equally spaced Shield,Multi-Max TA,APP-TA SBS-TA,
spans APP-TA
center rows FA3 or Polytherm
Min.22 ga., 7-inch o.c.at 4- Min.1.5-inch
Min.300 psi inch lap and 7- Polytherm,ACFoam
Type B,vented GAFGLAS OMG CR Polyflex SA (Optional)
LWC-23 steel at max.5 ft Approved #75 BSF inch o.c.in two, II,Polytherm H,H- HA None N/A Base APP-TA APP-TA -45.0
cellular LWC equally spaced Shield,Multi-Max
spans center rows FA3 or Polytherm
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 43 of 58
Q0
TRINITY ERD
TABLE 4C: LIGHTWEIGHT CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE E: MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
System Deck(Note 1) Lightweight Concrete(Note 14) Base Sheet (Note A below) Roof Cover(Note 15) MDP
No. Type Fasten Attach Base Ply Cap Ply (psf)
'GENERIC'CELLULAR LIGHTWEIGHT INSULATING CONCRETE:
Min.300 psi,min.2-inch thick
cellular LWC. Note:To qualify the 7-inch o.c.in a 3-inch lap and 7-inch o.c.in two,
LWC-24 Min.22 ga.,type B steel at max 5 LWIC under this assembly,an OMG B3 OMG CR BPF equally spaced,staggered rows in the field of the (Optional)BP- SBS-AA,APP- -45.0
ft spans or structural concrete CR BPF shall achieve an average AA,SBS-AA TA
withdrawal of 53 Ibf when tested per sheet
TAS 105 or ANSI/SPRI FX-1
CELCORE CELLULAR LIGHTWEIGHT INSULATING CONCRETE:
Min.0.0179-inch Tensilform S-75 8-inch o.c.in a 3-inch lap and 16-inch o.c.in two,
or min.0.0205-inch Tensilform Min.200 psi,min.2-inch thick Trufast FM-90
LWC-25 61,62,63 or 67 or OMG CR BPF equally spaced,staggered rows in the field of the BP-AA,SBS-AA SBS-AA 37.5
75 at max.5 ft spans or Celcore
structural concrete sheet
Min.22 ga.,type B steel at max 5 Min.200 psi,min.2-inch thick Trufast FM-90 7-inch o.c.in a 3-inch lap and 7-inch o.c.in two,
LWC-26 ft spans or structural concrete Celcore B1 through B12 or OMG CR BPF equally spaced,staggered rows in the field of the BP-AA,SBS-AA SBS-AA -45.0
sheet
Min.26 ga.,type HF steel at max Min.225 psi,min.2-inch thick B1,B2,B3,B4,B7, 9-inch o.c.in a 3-inch lap and 9-inch o.c.in two,
LWC-27 5 ft spans or structural concrete Celcore MF B8,B10,B11 or OMG CR BPF equally spaced,staggered rows in the field of the BP-AA,SBS-AA SBS-AA -45.0
B12 sheet
Min.22 ga.,type B steel at max 6 Min.225 psi,min.2-inch thick B1,B2,B3,B4,B7, 7-inch o.c.in a 3-inch lap and 14-inch o.c.in two,
LWC-28 ft spans or structural concrete Celcore MF B8,B10,B11 or OMG CR BPF equally spaced,staggered rows in the field of the BP-AA,SBS-AA SBS-AA -45.0
B12 sheet
Min.22 ga.,type B steel at max 6 Min.225 psi,min.2-inch thick B1,B2,B3,B4,B7, 9-inch o.c.in a 3-inch lap and 9-inch o.c.in two,
LWC-29 ft spans or structural concrete Celcore MF B8,B10,B11 or OMG CR BPF equally spaced,staggered rows in the field of the BP-AA,SBS-AA SBS-AA -45.0
B12 sheet
SBS-AA BP-AA in two c in a 4-inch lap and 18-inch o c. . . , , ,
Min.22 ga.,type B steel at max 5 Min.225 psi,min.2-inch thick Trufast Twin 9-inch o. SBS-AA,SBS-
LWC-30 ft spans or structural concrete Celcore MF B1 or B2 Loc-Nail equally spaced,staggered rows in the field of the SBS-TA or APP- TA,or APP-TA -45.0
sheet TA
Min.22 ga.,type B steel at max 5 Min.225 psi,min.2-inch thick B2(with poly-film 9-inch o.c.in a 4-inch lap and 18-inch o.c.in two,
ilm Trufast Twin SBS-SA,SBS-TA SBS-SA,APP-
LWC-31 ft spans or structural concrete Celcore MF top surface) Loc-Nail equally spaced,staggered rows in the field of the or APP-TA SA,SBS-TA or -45.0
sheet APP-TA
Min.22 ga.,type B steel at max 5 Min.225 psi,min.2-inch thick B2(with poly film Trufast Twin 9-inch o.c.in a 4-inch lap and 18-inch o.c.in two,
LWC-32 ft spans or structural concrete Celcore MF top surface) Loc-Nail equally spaced,staggered rows in the field of the Polyflex SA Base APP-TA -45.0
sheet
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick 8-inch o.c.in a 4-inch lap and 8-inch o.c.in three BP AA,SBS AA, SBS-AA,SBS-
LWC-33 ft spans or structural concrete Celcore MF 132 Trufast FM-90 equally spaced,staggered center rows TBAS-TA or APP- TA,or APP-TA -60.0
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick B2(with poly-film 8-inch o.c.in a 4-inch lap and 8-inch o.c.in three SBS-SA,SBS-TA SBS-SA,APP-
LWC-34 ft spans or structural concrete Celcore MF top surface) Trufast FM-90 equally spaced,staggered center rows or APP-TA SA,SBS-TA or -60.0
APP-TA
Exterior Research and Design,LLC.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6TR EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 44 of 58
QO
TRINITY ERD
TABLE 4C: LIGHTWEIGHT CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE E: MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
System Deck(Note 1) Lightweight Concrete(Note 14) Base Sheet (Note A below) Roof Cover(Note 15) MDP
No. Type Fasten Attach Base Ply Cap Ply (psf)
LWC-35 Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick B2(with poly film Trufast FM-90 8-inch o.c.in a 4-inch lap and 8-inch o.c.in three Polyflex SA Base APP-TA -60.0
ft spans or structural concrete Celcore MF top surface) equally spaced,staggered center rows
7-inch o.c.in a 3-inch lap and 7-inch o.c.in two,
LWC-36 Min. ga.,type B steel max 5 Min.300 psi,min.2-inch thick B1 through B12 Trufast FM-90 equally spaced,staggered rows in the field of the BP-AA,SBS-AA, SBS-AA,APP- -75.0
ft spans or structural concrete Celcore or OMG CR BPF sheet SBS-TA,APP-TA TA
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick 10-inch o.c.in a 4-inch lap and 10-inch o.c.in three (Optional)BP- SBS-AA,SBS-
LWC-37 ft spans or structural concrete Celcore MF Elastobase P Trufast FM-290 equally spaced,staggered center rows AA,SBS-AA,SBS- TA,APP-TA -90.0
TA or APP-TA
ELASTIZELL CELLULAR LIGHTWEIGHT INSULATING CONCRETE:
Min.0.0179-inch Tensilform S-75 7.5-inch o.c.in a 3-inch lap and 7.5-inch o.c.in two, BP-AA,SBS-AA,
or min.0.0205-inch Tensilform Min.200 psi,min.2-inch thick Trufast FM-90 SBS-AA,SBS-
LWC-38 75 at max.5 ft spans or Elastizell Range II 61 through 612 or OMG CR BPF equally spaced,staggered rows in the field of the SBS-TA,or APP- TA,or APP-TA 30.0
structural concrete sheet TA
Min.0.0179-inch Tensilform S-75 7.5-inch o.c.in a 3-inch lap and 7.5-inch o.c.in two, SBS-SA,APP-
or min.0.0205-inch Tensilform Min.200 psi,min.2-inch thick B2(with poly film Trufast FM-90 SBS-SA,SBS-TA
LWC-39 75 at max.5 ft spans or Elastizell Range II top surface) or OMG CR BPF equally spaced,staggered rows in the field of the or APP-TA SA,SBS-TA or 30.0
structural concrete sheet APP-TA
SBS-AA,
,
Min.22 ga.,type B steel at max 5 Min.200 psi,min.2-inch thick Trufast FM-90 7-inch o.c.in a 3-inch lap and 7-inch o.c.in two, SBS-AA,SBS-
LWC-40 ft spans or structural concrete Elastizell Range II B1 through B12 or OMG CR BPF equally spaced,staggered rows in the field of the SBS-TA,or APP- TA,or APP-TA -45.0
sheet TA
Min.22 ga.,type B steel at max 5 Min.200 psi,min.2-inch thick B2(with poly-film 7-inch o.c.in a 3-inch lap and 7-inch o.c.in two,
ilm Trufast FM-90 SBS-SA,SBS-TA SBS-SA,APP-
LWC-41 ft spans or structural concrete Elastizell Range II top surface) or OMG CR BPF equally spaced,staggered rows in the field of the Or APP-TA SA,SBS-TA or -45.0
sheet APP-TA
Min.22 ga.,type B steel at max 5 Min.200 psi,min.2-inch thick B2(with poly film Trufast FM-90 7-inch o.c.in a 3-inch lap and 7-inch o.c.in two,
LWC-42 ft spans or structural concrete Elastizell Range II top surface) or OMG CR BPF equally spaced,staggered rows in the field of the Polyflex SA Base APP-TA -45.0
sheet
min.2-inch thick
Min.22 ga.,type B vented steel Min.350 psi, Elastobase P(with 8-inch o.c.in a 4-inch lap and 8-inch o.c.in three, (Optional)BP-
Elastizell with Zell-Crete Fibers, SBS-AA,SBS-
LWC-43 at max 5 ft spans or structural supplemental attached with Roofgrip Poly film top Trufast FM-290 equally spaced,staggered rows in the field of the AA,SBS-AA,SBS- TA,or APP-TA
#21 and 3-inch plates at 1 per 8 ft2 -52.5
concrete surface) sheet TA,or APP-TA
Min.350 psi,min.2-inch thick SBS-AA,SBS-
Min.22 a., Trufast Twin 6-inch o.c.in a 4-inch lap and 6-inch o.c.in three,
g type B steel at max 5 Elastizell with Zell-Crete Fibers, TA,SBS-SA,
LWC-44 ft spans or structural concrete supplemental attached with Roofgrip B2 Loc-Nails(min. equally spaced,staggered rows in the field of the BP-AA or SBS-AA APP-TA or 60.0
#21 and 3-inch plates at 1 per 8 ft2 1.8-inch) sheet APP SA
Min.350 psi,min.2-inch thick Trufast Twin 6-inch o.c.in a 4-inch lap and 6-inch o.c.in three, SBS-SA,APP-
Min.22 ga.,type B steel at max 5 Elastizell with Zell-Crete Fibers, B2(with poly film SBS-SA,SBS-TA
LWC-45 ft spans or structural concrete supplemental attached with Roofgrip top surface) Loc-Nails(min. equally spaced,staggered rows in the field of the or APP-TA SA,SBS-TA or 60.0
#21 and 3-inch plates at 1 per 8 ft2 1.8-inch) sheet APP-TA
Exterior Research and Design,LLC.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 45 of 58
QO
TRINITY ERD
TABLE 4C: LIGHTWEIGHT CONCRETE DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE E: MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
System Deck(Note 1) Lightweight Concrete(Note 14) Base Sheet (Note A below) Roof Cover(Note 15) MDP
No. Type Fasten Attach Base Ply Cap Ply (psf)
Min.350 psi,min.2-inch thick Trufast Twin 6-inch o.c.in a 4-inch lap and 6-inch o.c.in three,
LWC-46 Min.22 ga.,type B steel at max 5 Elastizell with Zell-Crete Fibers, B2(with poly-film Loc-Nails(min. equally spaced,staggered rows in the field of the Polyflex SA Base APP-TA -60.0
ft spans or structural concrete supplemental attached with Roofgrip top surface) 1.8-inch) sheet
#21 and 3-inch plates at 1 per 8 ft2
MEARLCRETE CELLULAR LIGHTWEIGHT INSULATING CONCRETE:
Min.24 ga.,type B steel at max 5 Min.200 psi,min.2-inch thick Trufast FM-90 7.5-inch o.c.in a 3-inch lap and 10-inch o.c.in two,
LWC-47 ft spans or structural concrete Mearlcrete B1 through B12 or CMG CR BPF equally spaced,staggered rows in the field of the BP-AA,SBS-AA SBS-AA -30.0
sheet
SBS-AA BP-AA in two c in a 4-inch lap and 7-inch o c. . . , , ,
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick Trufast FM-90 7-inch o. SBS-AA,SBS-
LWC-48 ft spans or structural concrete Mearlcrete B1,B2 or B12 or CMG CR BPF equally spaced,staggered rows in the field of the SBS-TA,or APP- TA,or APP-TA -45.0
sheet TA
in two c in a 4-inch lap and 7-inch o c. . . ,
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick 62(with poly-film Trufast FM-90 7-inch o. SBS-SA,SBS-TA SBS-SA,APP-
LWC-49 ft spans or structural concrete Mearlcrete top surface) or OMG CR BPF equally spaced,staggered rows in the field of the or APP-TA SA,SBS-TA or -45.0
sheet APP-TA
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick B2(with poly film Trufast FM-90 7-inch o.c.in a 4-inch lap and 7-inch o.c.in two,
LWC-50 ft spans or structural concrete Mearlcrete top surface) or OMG CR BPF equally spaced,staggered rows in the field of the Polyflex SA Base APP-TA -45.0
sheet
SBS-AA BP-AA in two c in a 4-inch lap and 7-inch o c. . . , , ,
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick B1,B2,B3,B7 or Trufast FM-90 7-inch o. SBS-AA,SBS-
LWC-51 ft spans or structural concrete Mearlcrete B11 or OMG CR BPF equally spaced,staggered rows in the field of the SBS-TA,or APP- TA,or APP-TA -52.5
sheet TA
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick B2(with poly-film 7-inch o.c.in a 4-inch lap and 7-inch o.c.in two,
ilm Trufast FM-90 565-$A,565-TA SBS-SA,APP-
LWC-52 ft spans or structural concrete Mearlcrete top surface) or OMG CR BPF equally spaced,staggered rows in the field of the or APP-TA SA,SBS-TA or -52.5
sheet APP-TA
Min.22 ga.,type B steel at max 5 Min.300 psi,min.2-inch thick B2(with poly film Trufast FM-90 7-inch o.c.in a 4-inch lap and 7-inch o.c.in two,
LWC-53 ft spans or structural concrete Mearlcrete top surface) or OMG CR BPF equally spaced,staggered rows in the field of the Polyflex SA Base APP-TA -52.5
sheet
A. Base Sheets options in Table 4C are coded as follows:
➢ B1:Polyglass G2 Base;B2:Elastobase or Elastobase P;63:GAFGLAS#75;134:GAFGLAS Stratavent Nailable Venting Base Sheet,B5:GAFGLAS Ply 4;BE:GAFGLAS FlexPly 6;137:JM Perma Ply No.28;138:JM Vensulation;B9:JM
GlasPly IV,B10:JM GlasPly Premier,B11:Tarrko Glass-Base;B12:Tamko Vapor-Chan
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 46 of 58
Q0
TRINITY ERD
TABLE 5A: CEMENTITIOUS WOOD FIBER DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
System Base Insulation Layer Top Insulation Layer Roof Cover(Note 15)
No. Deck(Note 1) Type Attach Type Attach Base Ply Ply Cap Ply MDP(psf)
Min.1.5-inch Polytherm,ACFoam Min.0.25-inch Dens Deck,Dens Deck Prime, (Optional)BP-AA, SBS-AA,
Min.2.5-inch Tectum D-IS or SECUROCK Gypsum-Fiber Roof Board or min.
CWF-1 II,ISO 95+GL,Polytherm H,H- D-IS or OB500 BP-AA,SBS-AA SBS-AA,SBS-TA or SBS-TA, -45.0
Plank or Tectum LS Plank Shield,Polytherm,ENRGY-3 OB500 0.5-inch Structodek High Density Fiberboard APP-TA APP-TA
Roof Insulation
Min.1.5-inch Polytherm,ACFoam SBS-TA,SBS-
Min.2.5-inch Tectum D-IS or Min.0.25-inch Dens Deck,Dens Deck Prime, SBS-TA,SBS-SA or (Optional)SBS-TA,
CWF-2 Plank or Tectum LS Plank II,ISO 95+GL,Polytherm H,H- OB500 SECUROCK Gypsum-Fiber Roof Board D-IS or OB500 APP-TA SBS-SA or APP-TA SA,APP-TA, -45.0
Shield,Polytherm,ENRGY-3 APP-SA
Min.1.5-inch Polytherm,ACFoam
Min.2.5-inch Tectum D-IS or Min.0.25-inch Dens Deck,Dens Deck Prime,
CWF-3 Plank or Tectum LS Plank II,ISO 95+GL,Polytherm H,H- OB500 SECUROCK Gypsum-Fiber Roof Board D-IS or OB500 Polyflex SA Base (Optional)APP-TA APP-TA -45.0
Shield,Polytherm,ENRGY-3
Min.0.25-inch Dens Deck,Dens Deck Prime,
Min.1.5-inch Polytherm,ACFoam (Optional)BP-AA, SBS-AA,
Min.2.5-inch Tectum SECUROCK Gypsum-Fiber Roof Board or min.
CWF-4 II,ISO 95+GL,Polytherm H,H- CR-20 CR-20 BP-AA,SBS-AA SBS-AA,SBS-TA or SBS-TA, -52.5
Plank or Tectum LS Plank Shield,Polytherm,ENRGY-3 0.5-inch Structodek High Density Fiberboard APP-TA APP-TA
Roof Insulation
Min.1.5-inch Polytherm,ACFoam SBS-TA,SBS-
Min.2.5-inch Tectum Min.0.25-inch Dens Deck,Dens Deck Prime, SBS-TA,SBS-SA or (Optional)SBS-TA,
CWF-5 II,ISO 95+
Plank or Tectum LS Plank Polytherm H- CR-20 SA,APP-TA, 52.5
SECUROCK Gypsum-Fiber Roof Board CR-20 APP-TA SBS-SA or APP-TA
Shield,Polytherm,ENRGY-3 APP-SA
Min.2.5-inch Tectum Min.1.5-inch Polytherm,ACFoam Min.0.25-inch Dens Deck,Dens Deck Prime,
CWF-6 Plank or Tectum LS Plank II,ISO 95+GL,Polytherm H,H- CR-20 SECUROCK Gypsum-Fiber Roof Board CR-20 Polyflex SA Base (Optional)APP-TA APP-TA -52.5
Shield,Polytherm,ENRGY-3
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 47 of 58
Q0TFmNrry 'ERD
TABLE 5B: CEMENTITIOUS WOOD FIBER DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
System Deck Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15)
No. (Note 1) Type Fasten Attach Type Attach Type Attach Base Ply Ply Cap Ply MDP(psf)
Min.1.5-inch Polytherm, Min.0.25-inch Dens Deck,
Min.2.5-inch Elastobase, ACFoam II,Polytherm G,
9-inch o.c.in 4-inch Dens Deck Prime,SECUROCK
Tectum Plank Elastobase P, ACFoam III,15095+GL, Hot Hot BP-AA,
Trufast lap and 12-inch o.c. Gypsum-Fiber Roof Board, (Optional)BP- SBS-AA,
or Tectum LS Polyglass G2 Polytherm H,H-Shield, asphalt asphalt SBS-AA
CWF-7 Inuldek in two,equally Min.0.75-inch Fesco Board AA,SBS-AA,SBS- SBS-TA, -30.0*
Plank Base Loc-Nail spaced,staggered ENRGY 3,Polytherm or (homogeneous)or min.0.5- TA or APP-TA APP-TA
center rows Multi-Max FA3, inch Structodek High Density
Fiberboard Roof Insulation
9-inch o.c.in 4-inch
Min.1.5-inch Polytherm,
Min.2.5-inch Elastobase, ACFoam II,Polytherm G, SBS-TA,
Trufast lap and 12-inch o.c. Min.0.25-inch Dens Deck, SBS-TA, (Optional)565-
Tectum Plank Elastobase P, ACFoam III,ISO95+GL, Hot Hot SBS-SA,
CWF-8 Inuldek in two,equally Dens Deck Prime,SECUROCK SBS-SA or TA,SBS-SA or -30.0*
or Tectum LS Polyglass G2 Polytherm H,H-Shield, asphalt asphalt APP-TA,
Plank Base Loc-Nail spaced,staggered ENRGY 3,Polytherm or Gypsum-Fiber Roof Board APP-TA APP-TA APP-SA
center rows Multi-Max FA3,
9-inch o.c.in 4-inch
Min.1.5-inch Polytherm,
Min.2.5-inch Elastobase, ACFoam II,Polytherm G,
m
Trufast lap and 12-inch o.c. Min.0.25-inch Dens Deck, y (Optional)APP-
Tectu Plank Elastobase P, ACFoam III,ISO95+GL, Hot Hot Pol flex
CWF-9 Inuldek in two,equally Dens Deck Prime,SECUROCK APP-TA -30.0*
or Tectum LS Polyglass G2 Polytherm H,H-Shield, asphalt asphalt SA Base TA
Plank Base Loc-Nail spaced,staggered ENRGY 3,Polytherm or Gypsum-Fiber Roof Board
center rows Multi-Max FA3,
Min.1.5-inch Polytherm, Min.0.25-inch Dens Deck,
Min.2.5-inch Elastobase, ACFoam II,Polytherm G,
9-inch o.c.in 4-inch Dens Deck Prime,SECUROCK
Tectum Plank Elastobase P,
Trufast lap and 18-inch o.c. Gypsum-Fiber Roof Board, (Optional)BP- SBS-AA,
or Tectum LS Polyglass G2 Polytherm H,H-Shield, asphalt asphalt SBS-AA
WF-10 Twi ACFoam III,15095+GL, Hot Hot BP-AA,
n Loc- in two,equally Min.0.75-inch Fesco Board AA,SBS-AA,SBS- SBS-TA, -45.0*
Plank Base Nail spaced,staggered ENRGY 3,Polytherm or (homogeneous)or min.0.5- TA or APP-TA APP-TA
center rows Multi-Max FA3, inch Structodek High Density
Fiberboard Roof Insulation
9-inch o.c.in 4-inch Min.1.5-inch Polytherm,
Min.2.5-inch Elastobase, ACFoam ll,Polytherm G, SBS-TA,
Trufast lap and 18-inch o.c. Min.0.25-inch Dens Deck, SBS-TA, (Optional)SBS-
Tectum Plank Elastobase P, ACFoam III,ISO95+GL, Hot Hot SBS-SA,
WF-11 Twin Loc- in two,equally Dens Deck Prime,SECUROCK SBS-SA or TA,SBS-SA or -45.0*
or Tectum LS Polyglass G2 Polytherm H,H-Shield, asphalt asphalt APP-TA,
Plank Base Nail spaced,staggered ENRGY 3,Polytherm or Gypsum-Fiber Roof Board APP-TA APP-TA APP-SA
center rows Multi-Max FA3,
9-inch o.c.in 4-inch Min.1.5-inch Polytherm,
Min.2.5-inch Elastobase, ACFoam II,Polytherm G,
Trufast lap and 18-inch o.c. Min.0.25-inch Dens Deck, y (Optional)APP-
Tectum Plank Elastobase P, ACFoam III,ISO95+GL, Hot Hot Pol flex
WF-12 Twin Loc- in two,equally Dens Deck Prime,SECUROCK APP-TA -45.0*
or Tectum LS Polyglass G2 Polytherm H,H-Shield, asphalt asphalt SA Base TA
Plank Base Nail spaced,staggered ENRGY 3,Polytherm or Gypsum-Fiber Roof Board
center rows Multi-Max FA3,
Exterior Research and Design,LLC.d/b/a Trinity ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 48 of 58
Q0
TRINITY ERD
TABLE 5C: CEMENTITIOUS WOOD FIBER DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE B: MECHANICALLY ATTACHED BASE INSULATION,BONDED TOP INSULATION,BONDED ROOF COVER
System Deck Base Insulation Layer Top Insulation Layer Roof Cover(Note 15)
No. (Note 1) Type Fasten Attach Type Attach Base Ply Ply Cap Ply MDP(psf)
Min.2.5-inch Tectum Min.2-inch H- OMG Polymer GypTec Plate with Min.0.5-inch Structodek (Optional if (Optional if using AA SBS
CWF-13 Plank or Tectum LS Shield or Polymer GypTec or Trufast TL 3 1 per 4 ftZ High Density Fiberboard Hot using AA Ply) Base)BP-AA,SBS-AA, SBS-TA, -45.0*
Plank Polytherm in.Plate with TL Fastener Roof Insulation asphalt BP-AA SBS-AA SBS-TA or APP-TA APP-TA
TABLE 5D: CEMENTITIOUS WOOD FIBER DECKS—NEW CONSTRUCTION,REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER
System Deck Top Insulation Layer Roof Cover(Note 15)
Base Insulation Layer MDP(psf)
No. (Note 1) Type Fasten Attach Base Ply Ply Cap Ply
Min.2.5-inch (Optional)One or more Min.0.25-inch Dens Deck,Dens Deck Prime or Trufast Twin Loc-Nails (Optional if (Optional if using AA SBS-AA,
CWF-14 Tectum Plank or layers,any combination, SECUROCK Gypsum-Fiber Roof Board or min. (min.1-inch 1 per 2 ft2 using AA Ply) Base)BP-AA,SBS-AA, SBS-TA, -45.0*
Tectum LS Plank loose laid 0.5-inch Structodek High Density Fiberboard embedment) BP-AA,SBS-AA SBS-TA or APP-TA APP-TA
Roof Insulation
TABLE SE: CEMENTITIOUS WOOD FIBER DECKS—NEW CONSTRUCTION OR REROOF(TEAR-OFF)
SYSTEM TYPE E: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
System Deck Base Sheet Roof Cover(Note 15)
MDP(psf)
No.
(Note 1) Type Fasten Attach Base Ply Cap Ply
Min.2.5-inch Tectum SBS-AA,
CWF-15 Plank or Tectum equally spaced,LS Elastobase,Elastobase P,Polyglass G2 Base Trufast Inuldek Loc-Nail 9-inch o.p in ,inch lap and 12-inch staggered center rows so. SBS-TA or APP-TA in two, (Optional)BP-AA,SBS-AA, SBS-TA, -30.0*
Plank acedd, APP TA
Min.2.5-inch Tectum SBS-AA,
CWF-16 Plank or Tectum LS Elastobase,Elastobase P,Polyglass G2 Base Trufast Twin Loc-Nails equally
o.p in d,inch lap and 18-inch s in two, (Optional)BP-AA,SBS-AA, SBS-TA, -45.0*
Plank equally spaced,staggered center rows SBS-TA or APP-TA APP TA
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for F13654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 49 of 58
QO
TRINITY ERD
TABLE 6A: GYPSUM DECKS-REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
System Deck(Notes 1&12) Base Insulation Layer77 Top Insulation Layer Roof Cover(Note 15) MDP
No. Type Attach Type Attach Base Ply Ply Cap Ply lPsq
SELF-ADHERING BASE:
Existing,sound Min.1.5-inch Polytherm,ACFoam II, (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
G-1 poured gypsum or ENRGY 3,Polytherm H or H-Shield or min. OB500 Min.0.25-inch Dens Deck Prime OB500 SBS-SA APP-TA SBS-TA,APP-TA 72.5
gypsum plank deck 2.0 pcf,Insulfoam
Existing,sound (Optional)additional layers(s)of base
G-2 poured gypsum or Min.1.5-inch min.2.0 pcf,Insulfoam OB500 insulation OB500 SBS-SA (Optional)SBS-SA SBS-SA,APP-SA -112.5
gypsum plank deck
Existing,sound Min.1.5-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
G-3 poured gypsum or ENRGY 3,Polytherm H or H-Shield OB500 insulation OB500 SBS-SA APP-TA SBS-TA,APP-TA -112.5
gypsum plank deck
Existing,sound Min.1.5-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base Polyflex SA
G-4 poured gypsum or ENRGY 3,Polytherm H or H-Shield OB500 insulation OB500 Base (Optional)APP-TA APP-TA -112.5
gypsum plank deck
Existing,sound Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK Gypsum-Fiber (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
G-5 poured gypsum or ENRGY 3,Polytherm H or H-Shield or min. OB500 Roof Board OB500 SBS-SA APP-TA SBS-TA,APP-TA -112.5
gypsum plank deck 2.0 pcf,Insulfoam
Existing,sound Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK Gypsum-Fiber Polyflex SA
G-6 poured gypsum or ENRGY 3,Polytherm H or H-Shield or min. OB500 Roof Board OB500 Base (Optional)APP-TA APP-TA -112.5
gypsum plank deck 2.0 pcf,Insulfoam
Existing,sound Min.1.5-inch Polytherm,ACFoam II,
G-7 poured gypsum or M-OSFA Min.0.25-inch Dens Deck Prime M-OSFA SBS-SA (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, 72 5
gypsum plank deck ENRGY 3,H-Shield or Multi-Max FA3 APP-TA SBS-TA,APP-TA
Existing,sound Min.1.5-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
G-8 poured gypsum or ENRGY 3,H-Shield or Multi-Max FA3 M-OSFA insulation and/or min.0.25-inch SECUROCK M-OSFA SBS-SA APP-TA SBS-TA,APP-TA -202.5
gypsum plank deck Gypsum-Fiber Roof Board
Existing,sound Min.1.5-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base Polyflex SA
G-9 poured gypsum or ENRGY 3,H-Shield or Multi-Max FA3 M-OSFA insulation and/or min.0.25-inch SECUROCK M-OSFA Base (Optional)APP-TA APP-TA -202.5
gypsum plank deck Gypsum-Fiber Roof Board
Existing,sound Min.1.5-inch,min.2.0 pcf EPS insulation
G-10 board,Polytherm,ACFoam II,Polytherm (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA, 72.5
poured gypsum G,ACFoam III,ENRGY 3,Polytherm H,H- APP-TA SBS-TA,APP-TA
gypsum plank deck CR-20 Min.0.25-inch Dens Deck Prime CR-20 SBS-SA Shield,H-Shield CG or Multi-Max FA3
Existing,sound (Optional)additional layers of base
G-11 poured gypsum or Min.1.5-inch,min.2.0 pcf Insulfoam CR-20 CR-20 SBS-SA (Optional)SBS-SA SBS-SA -240.0
gypsum plank deck insulation
Existing,sound Min.0.25-inch SECUROCK Gypsum-Fiber (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
G-12 poured gypsum or Min.1.5-inch,min.2.0 pcf Insulfoam CR-20 Roof Board CR-20 SBS-SA APP-TA SBS-TA,APP-TA -240.0
gypsum plank deck
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6TR EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 50 of 58
QO
TRINITY ERD
TABLE 6A: GYPSUM DECKS—REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
System Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. Deck(Notes 1&12) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
Existing,sound Min.0.25-inch SECUROCK Gypsum-Fiber Polyflex SA
G-13 poured gypsum or Min.1.5-inch,min.2.0 pcf Insulfoam CR-20 CR-20 (Optional)APP-TA APP-TA -240.0
gypsum plank deck Roof Board Base
Min.1.5-inch Polytherm,ACFoam II,
Existing,sound (Optional)additional layers(s)of base
,
G-14 poured gypsum or Polytherm H,H-Shield,H-Shield C Polytherm G,ACFoam III,ENRGY 3 G or CR-20 insulation and/or min.0.25-inch SECUROCK CR-20 Base
Polyflex SA (Optional)APP-TA APP-TA -257.5
gypsum plank deck Multi-Max FA3 Gypsum-Fiber Roof Board
Min.1.5-inch Polytherm,ACFoam II,
Existing,sound (Optional)additional layers(s)of base
Polytherm G,ACFoam III,ENRGY 3, (Optional)SBS-SA,SBS-TA, SBS-SA,APP-SA,
G-15 poured gypsum Polytherm H,H-Shield,H-Shield CG or CR-20 insulation and/oroof Board min.0.25-inch SECUROCK CR-20 SBS-SA APP-TA SBS-TA,APP-TA 257.5
gypsum plank deck Multi-Max FA3 Gypsum-Fiber Roof
ASPHALT-APPLIED BASE:
Existing,sound Min.0.25-inch Dens Deck,Dens Deck (Optional if (Optional if using AA Base) SBS-AA,SBS-TA,
G-16 poured gypsum or Prime or SECUROCK Gypsum-Fiber Roof CR-20 None N/A using AA Ply) BP-AA,SBS-AA,SBS-TA or APP TA 245.0
gypsum plank deck Board BP-AA,SBS-AA APP-TA
COLD APPLIED BASE:
Min.1-inch Polytherm,ACFoam II, Min.0.25-inch Dens Deck,Dens Deck Prime,
Existing,sound Polytherm G,ACFoam III,EnergyGuard DEXcell FA Glass Mat Roof Board,SECUROCK
Polyiso Insulation,ENRGY 3,Polytherm H, Gypsum-Fiber Roof Board or SECUROCK SBS-CA1,SBS- (Optional)SBS-CA1,SBS- SBS-CA1,SBS-
G-17 poured gypsum H-Shield ISO 95+GL,Multi-Max FA3, M-OSFA Glass-Mat Roof Board,min.7/16-inch M-OSFA CA2 CA2 CA2,APP-CA1 120.0
gypsum plank deck RESISTA or UltraMax or min.2-inch DEXcell Cement Roof Board or min.0.5-inch
DECKMATE Plus or DECKMATE Plus FA SECUROCK Cement Roof Board
Min.1-inch Polytherm or ACFoam II,
Existing,sound Polytherm G,ACFoam III,EnergyGuard Min.0.25-inch Dens Deck Prime or DEXcell
Polyiso Insulation,ENRGY 3,Polytherm H, FA Glass Mat Roof Board,min.7/16-inch SBS-CA1,SBS-
G-18 poured gypsum H-Shield,ISO 95+GL,Multi-Max FA3, M-OSFA DEXcell Cement Roof Board or min.0.5-inch M-OSFA SBS-CA1 None CA2,APP-CA1 127.5
gypsum plank deck RESISTA or UltraMax or min.2-inch SECUROCK Cement Roof Board
DECKMATE Plus or DECKMATE Plus FA
Min.1-inch Polytherm or ACFoam ll,
Existing,sound Polytherm G,ACFoam III,EnergyGuard
G-19 Polyiso Insulation,ENRGY 3,Polytherm H, Min.0.25-inch SECUROCK Gypsum-Fiber SBS-CA1,SBS- SBS-CA1,SBS-
127.5
poured gypsum H-Shield,ISO 95+GL,Multi-Max FA3, M-OSFA Roof Board M-OSFA CA2 CA2,APP-CA1
gypsum plank deck None RESISTA or UltraMax or min.2-inch
DECKMATE Plus or DECKMATE Plus FA
Min.1-inch Polytherm or ACFoam II, Min.0.25-inch Dens Deck,Dens Deck Prime,
Existing,sound Polytherm G,ACFoam III,EnergyGuard DEXcell FA Glass Mat Roof Board,SECUROCK
Polyiso Insulation,ENRGY 3,Polytherm H, Gypsum-Fiber Roof Board or SECUROCK SBS-CA1,SBS- SBS-CA1,SBS-
202.5
G-20 poured gypsum H-Shield,ISO 95+GL,Multi-Max FA3, M-OSFA Glass-Mat Roof Board,min.7/16-inch M-OSFA CA2 CA2
gypsum plank deck None RESISTA or UltraMax or min.2-inch DEXcell Cement Roof Board or min.0.5-inch
DECKMATE Plus or DECKMATE Plus FA SECUROCK Cement Roof Board
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 51 of 58
QO
TRINITY ERD
TABLE 6A: GYPSUM DECKS—REROOF(TEAR-OFF)
SYSTEM TYPE A-1:BONDED INSULATION,BONDED ROOF COVER
System Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. Deck(Notes 1&12) Type Attach Type Attach Base Ply Ply Cap Ply (pso
Existing,sound Min.1-inch Polytherm,ACFoam II, Min.0.25-inch Dens Deck Prime,DEXcell FA SBS-CA1,SBS- (Optional)SBS-CA1,SBS- SBS-CA1,SBS-
G-21 poured gypsum or Polytherm G,ACFoam III,ENRGY 3, OB500 Glass Mat Roof Board or SECUROCK OB500 -112.5
gypsum plank deck Polytherm H,H-Shield or Multi-Max FA3 Gypsum-Fiber Roof Board CA2 CA2 CA2,APP-CA1
Existing,sound Min.1-inch Polytherm,ACFoam ll, Min.0.25-inch Dens Deck Prime or SBS-CA1,SBS- (Optional)SBS-CA1,SBS- SBS-CA1,SBS-
G-22 poured gypsum or Polytherm G,ACFoam III,ENRGY 3, CR-20 SECUROCK Gypsum-Fiber Roof Board CR-20 CA2 CA2 CA2,APP-CA1 -120.0
gypsum plank deck Polytherm H,H-Shield or Multi-Max FA3
Existing,sound Min.1-inch Polytherm,ACFoam II, Min.0.25-inch Dens Deck Prime or DEXcell SBS-CA1,SBS-
G-23 poured gypsum or Polytherm G,ACFoam III,ENRGY 3, CR-20 FA Glass Mat Roof Board CR-20 SBS-CA1 None CA2,APP-CA1 -127.5
gypsum plank deck Polytherm H,H-Shield or Multi-Max FA3
Existing,sound Min.1-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK Gypsum-Fiber SBS-CA1,SBS- SBS-CA1,SBS-
G-24 poured gypsum or Polytherm G,ACFoam III,ENRGY 3, CR-20 Roof Board CR-20 CA2 None CA2,APP-CA1 -127.5
gypsum plank deck Polytherm H,H-Shield or Multi-Max FA3
Existing,sound Min.1-inch ENRGY 3,Polytherm H,H- Min.0.25-inch Dens Deck Prime or SBS-CA1,SBS- SBS-CA1,SBS-
G-25 poured gypsum or Shield,Multi-Max FA3 CR-20 SECUROCK Gypsum-Fiber Roof Board CR-20 CA2 None CA2 -232.5
gypsum plank deck
TABLE 613: GYPSUM DECKS—REROOF(TEAR-OFF)
SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET,BONDED INSULATION,BONDED ROOF COVER
System Deck Anchor Sheet Base Insulation Top Insulation Roof Cover(Note 15) MDP
No. (Note 1) Type Fasten Attach Type Attach Type Attach Base Ply Ply Cap Ply (psf)
9-inch o.c.in 4- Min.1.5-inch Polytherm, Min.0.25-inch Dens Deck,Dens Deck
Existing,sound Elastobase, inch lap and 18- ACFoam Trufast FM-75 II,Polytherm G, Prime,SECUROCK Gypsum-Fiber Roof (Optional)
poured gypsum Elastobase inch o.c.in two, ACFoam III,15095+GL, Hot Board,Min.0.75-inch Fesco Board Hot BP-AA, BP-AA,SBS-
SBS-AA,
G-26 or FM-90 or SBS-TA, -45.0*
or gypsum P,Polyglass equally spaced, Polytherm H,H-Shield, asphalt (homogeneous)or min.0.5-inch asphalt SBS-AA AA,SBS-TA
plank deck G2 Base Twin Loc-Nails staggered center ENRGY 3,Polytherm or Structodek High Density Fiberboard or APP-TA APP TA
rows Multi-Max FA3 Roof Insulation
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 52 of 58
QO
TRINITY ERD
TABLE 6C: GYPSUM DECKS—REROOF(TEAR-OFF)OR RECOVER
SYSTEM TYPE C: MECHANICALLY ATTACHED INSULATION,BONDED ROOF COVER
System Deck Top Insulation Layer Roof Cover(Note 15)
Base Insulation Layer MDP(psf)
No. (Note 1) Type Fasten Attach Base Ply Ply Cap Ply
Existing sound (Optional)One or more Min.0.25-inch Dens Deck,Dens Deck Prime or Trufast Twin Loc- 1 per 2 (Optional if (Optional if using AA Base) SBS-AA,
G-27 poured gypsum or layers,any combination, SECUROCK Gypsum-Fiber Roof Board or min.0.5-inch Nails(min.1-inch z using AA Ply) BP-AA,SBS-AA,SBS-TA or SBS-TA, -45.0
gypsum plank deck loose laid Structodek High Density Fiberboard Roof Insulation embedment) ft BP-AA,SBS-AA APP-TA APP-TA
TABLE 61): GYPSUM DECKS—REROOF(TEAR-OFF)
SYSTEM TYPE E: NON-INSULATED,MECHANICALLY ATTACHED BASE SHEET,BONDED ROOF COVER
System Deck Base Sheet Roof Cover(Note 1S) MDP(psf)
No. (Note 1) Type Fasten Attach Base Ply Cap Ply
G 28 Existing sound poured gypsum Elastobase,Elastobase P, Trufast FM-75 or FM-90 9-inch o.c.in 4-inch lap and 18-inch o.c.in (Optional)BP-AA,SBS-AA,SBS-TA or SBS-AA,SBS-TA, -45.0*
or gypsum plank deck Polyglass G2 Base or Twin Loc-Nails two,equally spaced,staggered center rows APP-TA APP-TA
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 53 of 58
Q0
TRINITY I ERD
TABLE 7A: RECOVER APPLICATIONS
SYSTEM TYPE A-1: BONDED INSULATION,BONDED ROOF COVER
System Substrate Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Notes 1&12) Type Attach Type Attach Base Ply Ply Cap Ply IPA
SELF-ADHERING BASE:
(Optional)additional layers(s)of base insulation (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
R-1 Existing asphaltic roof Min.1.5-inch Multi-Max FA3 D-IS and/or min.0.25-inch SECUROCK Gypsum-Fiber D-IS SBS-SA TA,APP-TA SBS-TA,APP-TA -67.5
Roof Board or Dens Deck Prime
(Optional)additional layers(s)of base insulation Polyflex SA
R-2 Existing asphaltic roof Min.1.5-inch Multi-Max FA3 D-IS and/or min.0.25-inch SECUROCK Gypsum-Fiber D-IS Base (Optional)APP-TA APP-TA -67.5
Roof Board or Dens Deck Prime
Min.1.5-inch Polytherm,ACFoam II, (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
R-3 Existing asphaltic roof ENRGY 3 or Multi-Max FA3 or min.2.0 pcf D-IS Min.0.25-inch Dens Deck Prime D-IS SBS-SA TA,APP-TA SBS-TA,APP-TA 72.5
Insulfoam
R-4 Existing asphaltic roof Min.1.5-inch min.2.0 pcf Insulfoam D-IS (Optional)additional layers(s)of base insulation D-IS SBS-SA (Optional)SBS-SA SBS-SA -90.0
R-5 Existing asphaltic roof Min.1.5-inch min.2.0 pcf Insulfoam D-IS Min.0.25-inch SECUROCK Gypsum-Fiber Roof D-IS SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, -90.0
Board TA,APP-TA SBS-TA,APP-TA
R-6 Existing asphaltic roof Min.1.5-inch min.2.0 pcf Insulfoam D-IS Min.0.25-inch SECUROCK Gypsum-Fiber Roof D-IS Polyflex SA (Optional)APP-TA APP-TA -90.0
Board Base
(Optional)additional layers(s)of base insulation
R-7 Existing asphaltic roof Min.1.5-inch Polytherm,ACFoam II or D-IS and/or min.0.25-inch SECUROCK Gypsum-Fiber D-IS SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, -90.0
Roof Board
ENRGY 3 TA,APP-TA SBS-TA,APP-TA
(Optional)additional layers(s)of base insulation
Min.1.5-inch Polytherm,ACFoam II or Polyflex SA
R-8 Existing asphaltic roof ENRGY 3 D-IS and/or min.0.25-inch SECUROCK Gypsum-Fiber D-IS Base (Optional)APP-TA APP-TA -90.0
Roof Board
Existing smooth-or
granule-surfaced asphalt (Optional)Min.1-inch Polytherm, Min.0.25-inch Dens Deck Prime,DEXcell FA Polyflex SA
R-9 built-up roof or SBS ACFoam II,Polytherm G,ACFoam III, D-IS Glass Mat Roof Board or SECUROCK Gypsum- D-IS Base primed None SBS-SA,APP-SA -93.8
modified bitumen or Fiber Roof Board
existing granule-surfaced Polytherm H or H-Shield PRIMER: PG100 with PG100
APP modified bitumen
Min.1.5-inch Polytherm,ACFoam II, (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
R-10 Existing asphaltic roof ENRGY 3,Polytherm H or H-Shield or min. OB500 Min.0.25-inch Dens Deck Prime OB500 SBS-SA TA,APP-TA SBS-TA,APP-TA 72.5
2.0 pcf Insulfoam
Existing smooth-or
granule-surfaced asphalt (Optional)Min.1-inch Polytherm, Min.0.25-inch Dens Deck Prime,DEXcell FA Polyflex SA
built-up roof or SBS Glass Mat Roof Board or SECUROCK Gypsum-
R-11 modified bitumen or ACFoam II,Polytherm G,ACFoam III, OB500 Fiber Roof Board OB500 Base primed None SBS-SA,APP-SA 93.8
existing granule-surfaced Polytherm H or H-Shield PRIMER: PG100 with PG100
APP modified bitumen
R-12 Existing asphaltic roof Min.1.5-inch,min.2.0 pcf Insulfoam OB500 (Optional)additional layers of base insulation OB500 SBS-SA (Optional)SBS-SA SBS-SA -120.0
R-13 Existing asphaltic roof Min.1.5-inch,min.2.0 pcf Insulfoam OB500 Min.0.25-inch SECUROCK Gypsum-Fiber Roof OB500 SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, -120.0
Board TA,APP-TA SBS-TA,APP-TA
R-14 Existing asphaltic roof Min.1.5-inch,min.2.0 pcf Insulfoam OB500 Min.0.25-inch SECUROCK Gypsum-Fiber Roof OB500 Polyflex SA (Optional)APP-TA APP-TA -120.0
Board Base
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL1654-R22
Certificate of Authorization#9503 6"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 54 of 58
QO
TRINITY ERD
TABLE 7A: RECOVER APPLICATIONS
SYSTEM TYPE A-1: BONDED INSULATION,BONDED ROOF COVER
System Substrate Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Notes 1&12) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
Min.1.5-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base insulation (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
R-15 Existing asphaltic roof ENRGY 3,Polytherm H or H-Shield OB500 and/or min.0.25-inch SECUROCK Gypsum-Fiber OB500 SBS-SA TA,APP-TA SBS-TA,APP-TA -127.5
Roof Board
Min.1.5-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base insulation Polyflex SA
R-16 Existing asphaltic roof ENRGY 3,Polytherm H or H-Shield OB500 and/or min.0.25-inch SECUROCK Gypsum-Fiber OB500 Base (Optional)APP-TA APP-TA -127.5
Roof Board
R-17 Existing asphaltic roof Min.1.5-inch Polytherm,ACFoam II, M-OSFA Min.0.25-inch Dens Deck Prime M-OSFA SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, 72 5
ENRGY 3,H-Shield or Multi-Max FA3 TA,APP-TA SBS-TA,APP-TA
Existing smooth-or
granule-surfaced asphalt Min.0.25-inch Dens Deck Prime,DEXcell FA
(Optional)Min.1-inch Polytherm, Polyflex SA
built-up roof or SBS M-OSFA Glass Mat Roof Board or SECUROCK Gypsum- M-OSFA
R-18 modified bitumen or ACFoam II,Polytherm G,ACFoam III, or M-PG1 Fiber Roof Board or M-PG1 Base primed None SBS-SA,APP-SA -93.8
existing granule-surfaced Polytherm H or H-Shield PRIMER: PG100 with PG100
APP modified bitumen
Min.1.5-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base insulation (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
R-19 Existing asphaltic roof ENRGY 3,H-Shield or Multi-Max FA3 M-OSFA and/or min.0.25-inch SECUROCK Gypsum-Fiber M-OSFA SBS-SA TA,APP-TA SBS-TA,APP-TA -157.5
Roof Board
Min.1.5-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base insulation Polyflex SA
R-20 Existing asphaltic roof ENRGY 3,H-Shield or Multi-Max FA3 M-OSFA and/or min.0.25-inch SECUROCK Gypsum-Fiber M-OSFA Base (Optional)APP-TA APP-TA -157.5
Roof Board
Min.1.5-inch min.2.0 pcf Insulfoam,
Min.2-inch Polytherm,ACFoam II,min.
1.5-inch Ultra-Max or Multi-Max FA-3, (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
R-21 Existing asphaltic roof min.1.3-inch Polytherm G,ACFoam III or CR-20 Min.0.25-inch Dens Deck Prime CR-20 SBS-SA TA,APP-TA SBS-TA,APP-TA 72.5
min.1.0-inch ISO 95+GL,Polytherm H,H-
Shield,H-Shield CG or ENRGY 3
Existing smooth-or
granule-surfaced asphalt (Optional)Min.1-inch Polytherm, Min.0.25-inch Dens Deck Prime,DEXcell FA Polyflex SA
built-up roof or SBS Glass Mat Roof Board or SECUROCK Gypsum-
R-22 modified bitumen or ACFoam II,Polytherm G,ACFoam III, CR-20 Fiber Roof Board CR-20 Base primed None SBS-SA,APP-SA 93.8
existing granule-surfaced Polytherm H or H-Shield PRIMER: PG100 with PG100
APP modified bitumen
R-23 Existing asphaltic roof Min.1.5-inch min.2.0 pcf Insulfoam CR-20 (Optional)additional layers(s)of base insulation CR-20 SBS-SA (Optional)SBS-SA SBS-SA -240.0
R-24 Existing asphaltic roof Min.1.5-inch min.2.0 pcf Insulfoam CR-20 Min.0.25-inch SECUROCK Gypsum-Fiber Roof CR-20 SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, -240.0
Board TA,APP-TA SBS-TA,APP-TA
Min.1.5-inch Ultra-Max or Multi-Max FA- (Optional)additional layers(s)of base insulation
3,min.1.3-inch Polytherm G,ACFoam III (Optional)SBS-SA,SBS- SBS-SA,APP-SA,
R-25 Existing asphaltic roof or min.1.0-inch ISO 95+GL,Polytherm H, CR-20 and/or min.0.25-inch SECUROCK Gypsum-Fiber CR-20 SBS-SA TA,APP-TA SBS-TA,APP-TA 240.0
H-Shield,H-Shield CG or ENRGY 3 Roof Board
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-1122
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 55 of 58
QO
TRINITY ERD
TABLE 7A: RECOVER APPLICATIONS
SYSTEM TYPE A-1: BONDED INSULATION,BONDED ROOF COVER
System Substrate Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Notes 1&12) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
Min.1.5-inch Ultra-Max or Multi-Max FA- (Optional)additional layers(s)of base insulation
3,min.1.3-inch Polytherm G,ACFoam III Polyflex SA
R-26 Existing asphaltic roof or min.1.0-inch ISO 95+GL,Polytherm H, CR-20 and/or min.0.25-inch SECUROCK Gypsum-Fiber CR-20 Base (Optional)APP-TA APP-TA 240.0
H-Shield,H-Shield CG or ENRGY 3 Roof Board
(Optional)additional layers(s)of base insulation
R-27 Existing asphaltic roof Min.2-inch Polytherm,ACFoam II, CR-20 and/or min.0.25-inch SECUROCK Gypsum-Fiber CR-20 SBS-SA (Optional)SBS-SA,SBS- SBS-SA,APP-SA, -247.5
ENRGY-3,Polytherm H or H-Shield Roof Board TA,APP-TA SBS-TA,APP-TA
Min.2-inch Polytherm,ACFoam II, (Optional)additional layers(s)of base insulation Polyflex SA
R-28 Existing asphaltic roof ENRGY-3,Polytherm H or H-Shield CR-20 and/or min.0.25-inch SECUROCK Gypsum-Fiber CR-20 Base (Optional)APP-TA APP-TA -247.5
Roof Board
ASPHALT OR TORCH APPLIED BASE:
Min.0.25-inch Dens Deck,Dens Deck Prime or BP AA,SBS (Optional)BP-AA,SBS- SBS-AA,SBS-TA
R-29 Existing asphaltic roof Min.1.5-inch Multi-Max FA3 D-IS SECUROCK Gypsum-Fiber Roof Board D-IS AA,SBS-TA, AA SBS-TA or APP-TA or APP-TA -67.5
APP-TA
Min.1.5-inch Polytherm,ACFoam II or Min.0.25-inch Dens Deck,Dens Deck Prime or BP AA,SBS (Optional)BP-AA,SBS- SBS-AA,SBS-TA,
R-30 Existing asphaltic roof ENRGY 3 or min.2.0 pcf Insulfoam D-IS SECUROCK Gypsum-Fiber Roof Board D-IS AA,SBS-TA, AA SBS-TA or APP-TA or APP-TA -90.0
APP-TA
Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch Dens Deck,Dens Deck Prime or BP AA,SBS (Optional)BP-AA,SBS- SBS-AA,SBS-TA,
R-31 Existing asphaltic roof ENRGY 3,H-Shield or ISO 95+GL OB500 SECUROCK Gypsum-Fiber Roof Board OB500 AA,SBS-TA, AA SBS-TA or APP-TA or APP-TA -127.5
APP-TA
Min.1.5-inch Polytherm,ACFoam II, Min.0.25-inch SECUROCK Gypsum-Fiber Roof BP AA,SBS (Optional)BP-AA,SBS- SBS-AA,SBS-TA,
R-32 Existing asphaltic roof ENRGY 3,H-Shield or Multi-Max FA3 M-OSFA Board M-OSFA AA,SBS-TA, AA SBS-TA or APP-TA or APP-TA -157.5
APP-TA
Min.1.5-inch Ultra-Max or Multi-Max FA-
3,min.1.3-inch Polytherm G,ACFoam III Min.0.25-inch SECUROCK Gypsum-Fiber BP-AA,SBS-
R-33 Existing asphaltic roof or min.1.0-inch ISO 95+GL,Polytherm H, CR-20 Board YP Roof CR-20 AA (Optional)BP-AA,SBS- SBS-AA -225.0
H-Shield,H-Shield CG or ENRGY 3 or min.
2.0 pcf Insulfoam
Min.1.5-inch Ultra-Max or Multi-Max FA-
3,min.1.3-inch Polytherm G,ACFoam III Min.0.25-inch SECUROCK Gypsum-Fiber Roof
R-34 Existing asphaltic roof or min.1.0-inch ISO 95+GL,Polytherm H, CR-20 Board CR-20 APP-TA (Optional)APP-TA APP-TA -232.5
H-Shield,H-Shield CG or ENRGY 3 or min.
2.0 pcf Insulfoam
COLD APPLIED BASE:
(Optional)Min.1-inch Polytherm, Min.0.25-inch Dens Deck Prime,DEXcell FA SBS-CA1, (Optional)SBS-CA1, SBS-CA1,SBS-
R-35 Existing asphaltic roof ACFoam II,Polytherm G,ACFoam III, D-IS Glass Mat Roof Board or SECUROCK Gypsum- D-IS SBS-CA2 SBS-CA2 CA2,APP-CA1 90.0
ENRGY 3,Polytherm H or H-Shield Fiber Roof Board
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 56 of 58
QO
TRINITY ERD
TABLE 7A: RECOVER APPLICATIONS
SYSTEM TYPE A-1: BONDED INSULATION,BONDED ROOF COVER
System Substrate Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Notes 1&12) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
(Optional)Min.1-inch Polytherm,
ACFoam II,Polytherm G,ACFoam III, Min.0.25-inch Dens Deck,Dens Deck Prime,
EnergyGuard Polyiso Insulation,ENRGY 3, DEXcell FA Glass Mat Roof Board,SECUROCK
M-OSFA, Gypsum-Fiber Roof Board or SECUROCK Glass- M-OSFA SBS-CA1, (Optional)SBS-CA1, SBS-CA1,SBS-
R-36 Existing asphaltic roof Polytherm H,H-Shield ISO 95+GL,Multi- -120.0
Max FA3,RESISTA or UltraMax or min.2- M-PG1 Mat Roof Board,min.7/16-inch DEXcell Cement or M-PG1 SBS-CA2 SBS-CA2 CA2,APP-CA1
inch DECKMATE Plus or DECKMATE Plus Roof Board or min.0.5-inch SECUROCK Cement
Roof Board
FA
(Optional)Min.1-inch Polytherm or
ACFoam II,Polytherm G,ACFoam III, Min.0.25-inch Dens Deck Prime or DEXcell FA
EnergyGuard Polyiso Insulation,ENRGY 3, M-OSFA, Glass Mat Roof Board,min.7/16-inch DEXcell M-OSFA, SBS-CA1,SBS-
R-37 Existing asphaltic roof Polytherm H,H-Shield,ISO 95+GL,Multi- M-PG1 Cement Roof Board or min.0.5-inch SECUROCK M-PG1 SBS-CA1 None CA2,APP-CA1 -127.5
Max FA3,RESISTA or UltraMax or min.2-
inch DECKMATE Plus or DECKMATE Plus Cement Roof Board
FA
(Optional)Min.1-inch Polytherm or
ACFoam II,Polytherm G,ACFoam III,
EnergyGuard Polyiso Insulation,ENRGY 3, M-OSFA, Min.0.25-inch SECUROCK Gypsum-Fiber Roof M-OSFA, SBS-CA1, SBS-CA1,SBS-
R-38 Existing asphaltic roof Polytherm H,H-Shield,ISO 95+GL,Multi- M-PG1 Board M-PG1 SBS-CA2 None CA2,APP-CA1 -127.5
Max FA3,RESISTA or UltraMax or min.2-
inch DECKMATE Plus or DECKMATE Plus
FA
(Optional)Min.1-inch Polytherm or Min.0.25-inch Dens Deck,Dens Deck Prime,
ACFoam II,Polytherm G,ACFoam III, DEXcell FA Glass Mat Roof Board,SECUROCK
EnergyGuard Polyiso Insulation,ENRGY 3, M-OSFA, Gypsum-Fiber Roof Board or SECUROCK Glass- M-OSFA, SBS-CAI, SBS-CA1,SBS-
R-39 Existing asphaltic roof Polytherm H,H-Shield,ISO 95+GL,Multi- None -157.5
Max FA3,RESISTA or UltraMax or min.2- M-PG1 Mat Roof Board,min.7/16-inch DEXcell Cement M-PG1 SBS-CA2 CA2
inch DECKMATE Plus or DECKMATE Plus Roof Board or min.0.5-inch SECUROCK Cement
Roof Board
FA
(Optional)Min.1-inch Polytherm, Min.0.25-inch Dens Deck Prime,DEXcell FA
R-40 Existing asphaltic roof ACFoam II,Polytherm G,ACFoam III, OB500 Glass Mat Roof Board or SECUROCK Gypsum- OB500 SBS-CA1, (Optional)SBS-CA1, SBS-CA1,SBS- -120.0
ENRGY 3,Polytherm H,H-Shield or Multi- Fiber Roof Board SBS-CA2 SBS-CA2 CA2,APP-CA1
Max FA3
(Optional)Min.1-inch Polytherm,
R-41 Existing asphaltic roof ACFoam II,Polytherm G,ACFoam III, OB500 Min.0.25-inch Dens Deck Prime or DEXcell FA OB500 SBS-CA1 None SBS-CA1,SBS- -127.5
ENRGY 3,Polytherm H,H-Shield or Multi- Glass Mat Roof Board CA2,APP-CA1
Max FA3
(Optional)Min.1-inch Polytherm,
R-42 Existing asphaltic roof ACFoam II,Polytherm G,ACFoam III, OB500 Min.0.25-inch SECUROCK Gypsum-Fiber Roof OB500 SBS-CA1, None SBS-CA1,SBS- -127.5
ENRGY 3,Polytherm H,H-Shield or Multi- Board SBS-CA2 CA2,APP-CA1
Max FA3
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 57 of 58
QO
TRINITY ERD
TABLE 7A: RECOVER APPLICATIONS
SYSTEM TYPE A-1: BONDED INSULATION,BONDED ROOF COVER
System Substrate Base Insulation Layer Top Insulation Layer Roof Cover(Note 15) MDP
No. (Notes 1&12) Type Attach Type Attach Base Ply Ply Cap Ply (psf)
(Optional)Min.1-inch Polytherm,
R-43 Existing asphaltic roof ACFoam II,Polytherm G,ACFoam III, CR-20 Min.0.25-inch Dens Deck Prime or SECUROCK CR-20 SBS-CA1, (Optional)SBS-CA1, SBS-CA1,SBS- -120.0
ENRGY 3,Polytherm H,H-Shield or Multi- Gypsum-Fiber Roof Board SBS-CA2 SBS-CA2 CA2,APP-CA1
Max FA3
(Optional)Min.1-inch Polytherm,
R-44 Existing asphaltic roof ACFoam II,Polytherm G,ACFoam III, CR-20 Min.0.25-inch Dens Deck Prime or DEXcell FA CR-20 SBS-CA1 None SBS-CA1,SBS- -127.5
ENRGY 3,Polytherm H,H-Shield or Multi- Glass Mat Roof Board CA2,APP-CA1
Max FA3
(Optional)Min.1-inch Polytherm,
R-45 Existing asphaltic roof ACFoam II,Polytherm G,ACFoam III, CR-20 Min.0.25-inch SECUROCK Gypsum-Fiber Roof CR-20 SBS-CAI, None SBS-CA1,SBS- -127.5
ENRGY 3,Polytherm H,H-Shield or Multi- Board SBS-CA2 CA2,APP-CA1
Max FA3
(Optional)Min.1-inch ENRGY 3, Min.0.25-inch Dens Deck Prime or SECUROCK CR-20 SBS-CA1, None SBS-CA1,SBS-
232.5
R-46 Existing asphaltic roof Polytherm H,H-Shield,Multi-Max FA3 CR-20 Gypsum-Fiber Roof Board SBS-CA2 CA2
TABLE7B: RECOVER APPLICATIONS
SYSTEM TYPE F:NON-INSULATED,BONDED BASE SHEET,BONDED ROOF COVER
System No. Substrate Primer Roof Cover(Note 15) MDP(psf)
(Notes 1&12) Base Ply Ply Cap Ply
Existing asphaltic (Optional if using asphalt applied Base)BP-AA,SBS-
R-47 roof PG100 BP-AA(Optional if using asphalt applied Ply) AA SBS-TA or APP-TA SBS-AA,SBS-TA,APP-TA 45.0
Exterior Research and Design,I.I.C.d/b/a Trinity I ERD Evaluation Report P9290.02.08-R20 for FL3654-R22
Certificate of Authorization#9503 6T"EDITION(2017)FBC NON-HVHZ EVALUATION Revision 20:09/12/2017
Prepared by: Robert Nieminen,PE-59166 Polyglass Modified Bitumen Roof Systems;(570)384-1230 Appendix 1,Page 58 of 58