The URL can be used to link to this page

Home My WebLink AboutNOA; 5-V Crimp Metal Roofing Panel SystemMIAMI 12 °a 0 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) BOARD AND CODE ADMINISTRATION DIVISION NOTICE OF ACCEPTANCE (NO Southeastern Metals Manufacturing Co., Inc. 11801 Industry Drive Jacksonville, FL 32218 SCOPE: MIAMI-DADE COUNTY PRODUCT CONTROL SECTION H 805 SW 26 Street, Room 208 Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 ,.,v,Nvw.iniamidade.gov/ccononiv This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: 5-V Crimp Metal Roofing Panel System LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA No.11-0714.08 and consists of pages 1 through 5. The submitted documentation was reviewed by Gaspar J Rodriguez. FILE COPY NOA No.: 16-0510.23 Expiration Date: 11/08/21 Approval Date: 06/30/16 Page 1 of 5 ROOFING SYSTEM APPROVAL Category: Roofing Sub -Category: Non -Structural Metal Roofing Material: Steel Maximum Design Pressure: -180 PSF TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: Product Dimensions Test Specifications Product Description 5V Crimp Metal Length : various TAS 125 Corrosion resistant, galvalume or Roof Panels Height :'/,6" galvanized performed, Kynar or Width: 25 ''/2" SuperL II coated, pre -finished, metal (Coverage width: 24") panels. Thickness: 0.0217 Yield Strength: Min.53ksi MANUFACTURING LOCATION: 1. Jacksonville, FL EVIDENCE SUBMITTED: Test Agency Test Identifier Test Name/Report Date PRI Construction Materials SEM-011-02-05 TAS-125 11/23/10 Technologies PRI Construction Materials SEM-011-02-07 ASTM E 8 05/07/12 Technologies Farabaugh Engineering and T270-07 TAS-100 08/24/07 Testing, Inc. Farabaugh Engineering and T166-07 TAS-100 04/15/07 Testing, Inc. Force Engineering & Testing, 188-0331T-06A-C TAS-125 02/26/07 Inc. Hurricane Test Laboratory, LLC. 0041-0906-07 TAS-125 09/12/07 BASF Accelerated Weathering ASTM G 154 07/12/07 BASF Salt Spray ASTM B 117 07/12/07 NOA No.: 16-0510.23 Expiration Date: 11/08/21 Approval Date: 06/30/16 Page 2 of 5 APPROVED ASSEMBLIES: System: "5V-Crimp" Metal Panels Deck Type: Wood, Non -insulated Deck Description: 19/32" or greater plywood or wood plank. Slope Range: 2": 12" or greater Maximum Uplift Pressure: See Table A Below Deck Attachment: In accordance with applicable building code, but in no case it shall be less than 8d annular ring shank nails spaced at 6" o.c. In re -roofing, where deck is less than 19/32" thick (minimum 15/32") the above attachment method must be in addition to existing attachment. Underlayment: Minimum underlayment shall be an ASTM D 226 Type II installed with a minimum 4" side - lap and 6" end -laps. Underlayment shall be fastened with corrosion resistant tin -caps and 12 gauge 1-'/a" annular ring -shank nails, spaced 6" o.c. at all laps and two staggered rows 12" o.c. in the field of the roll. Or, any approved underlayment having a current NOA. Valleys: Valley construction shall be in compliance with Roofing Application Standard RAS 133 and with current published installation instructions and details in Southeastern Metal Manufacturing Metal Roofing Installation Manual. Fire Barrier Board: Any approved fire barrier having a current NOA. Refer to a current fire directory listing for fire ratings of this roofing system assembly as well as the location of the fire barrier within the assembly. See Limitation # 1. Metal Panels and Install the "5V-Crimp Panels" and accessories in compliance with the current published Accessories: installation instructions and details in Southeastern Metals Manufacturing Company's Installation Manual. Flashings, penetrations, valley construction and other details shall be constructed in compliance with Roofing Application Standard RAS 133. 1. At the eave, rake, and ridge, fasteners shall be located not more than 3" away from the panel end. 2. The leading side edge of the panel should be the side with the anti -siphon groove; each panel side will overlap this channel to provide a capillary brake. 3. The panels shall be fastened with metal roofing sealing washer screws with dimensions as listed below in Table A, in the crown of the inverted V ribs as shown in the details herein. 4. The panel's width fasteners shall be spaced at 11 ''/z" to the center rib, Then 12 %Z" to the next, perpendicular to the slope, through the overlapping panel. The flat area of the panel as shown in the details herein. 5. The panels fastening pattern at the interior of the panel, shall be in rows spaced as listed in Table A below, running parallel to the slope of the roof. Table A Maximum Desi n Pressure Field Perimeter and Corners Perimeter and Corner, Maximum Design Pressure -67.25 PSF -154.75 PSF -180 PSF Fastener Type #9 x 2" #9 x 2" #10-14 x 2-1/2" Maximum Fastener Spacing 16" OC 8" OC 8" OC 1. Extrapolation shall not be allowed NOA No.: 16-0510.23 Expiration Date: 11/08/21 Approval Date: 06/30/16 Page 3 of 5 LIMITATIONS 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. The maximum designed pressure listed herein shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). 3.. Panels may be rolls formed in continuous lengths from eave to ridge. Maximum lengths shall be as described in Roofing Application Standard RAS 133 4. All panels shall be permanently labeled with the manufacturer's name and/or logo, and the following statement: "Miami -Dade County Product Control Approved" or with the Miami -Dade County Product Control Sea] as seen below. All clips shall be permanently labeled with the manufacturer's name and/or logo, and/or model. of _ APpPROV,ED 5. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61G20-3 of the Florida Administrative Code. NOA No.: 16-0510.23 MIAM�4DAD CCODUNTY Expiration Date: 11/08/21 Approval Date: 06/30/16 Page 4 of 5 "5-V CRIMP METAL ROOF PANELS 25 1/2" 111/2" 121/2" f-/-1J I GINIIVV rI11 I GF%IN roll J V-%,V%I lVlr P11 IIN 1 I-l\l%Jl% Vl 1 rl%19LL 25 1/2" 111/2" 121/2" 1111-- FASTENING PATTERN FOR 5V-CRIMP AT EAVE & RIDGE SeeTable A Herein for Maximum END OF THIS ACCEPTANCE NOA No.: 16-0510.23 MIAMI•DAD, COUNTY Expiration Date: 11/08/21 Approval Date: 06/30/16 Page 5 of 5