HomeMy WebLinkAboutS881-MFP20102810000DEMO I etc.
04 Certificate of Authorization #32455
353 Christian Street, Unit #13
Oxford, CT 06478
(203) 262-9245
ENGINEER EVALUATE TEST CONSULT
EVALUATION•
Polyglass USA, Inc. Evaluation Report P12060.02.09 -R26
1111 West Newport Center Drive FLS259-1130
Deerfield Beach, FL 33442 Date of Issuance: 02/24/2009
(9S4) 233-1230 Revision 26: 07/06/2020
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for
use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described
herein have been evaluated for compliance with the 61h Edition (2017) Florida Building Code sections noted herein.
DESCRIPTION: Polyglass Roof Underlayments
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this
Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. of any changes to the
product(s), the Quality Assurance or the production facility location(s). NEMO I etc. requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "NEMO retc. Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distributors and sh__ lalbe available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 16.
Prepared by:
Robert -J.. -M Nieminen, P.E.
Florida Registration No. 59166, Florida DCA ANE1983
The facsimile seal appearing was authorized by Robert Nieminen, P.E. on
F -17/06/2020—.T ' 'caiiy-signed dMill —t
CERTIFICATION OF INDEPENDENCE:
1. NEMOletc. does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEMO I etc. is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
S. This is a building code evaluation. Neither NEMO Ietc. nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
02019 NEMO ETC, LLC
AK'l
WNEMOIetc.
1. SCOPE:
Product Category: Roofing
Sub -Category: U n derlayment
Compliance Statement: Roof Underlayments, as produced by Polyglass USA, Inc., have demonstrated compliance with the
following sections of the 611 Edition (2017) Florida Building Code through testing in accordance with the following Standards.
Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein.
2. STANDARDS:
Section
1504.3.1
1504.3.1
1507.2.3 /1507.1.1
1507.2.4 / 1507.1.1, 1507.2.9.2
1507.3.3
1507.11.2
1507.11.2
1507.11.2
1507.11.2
TAS 110
Property
Wind resistance
Wind resistance
Material standard
Material standard
Material standard
Material standard
Material standard
Material standard
Material standard
Accelerated Weathering
3. REFERENCES:
Year
FM 4474
2011
Ent!
Examination
Reference
Date
ASTM D1970
ERD (TST 6049)
Wind Uplift
11757.08.01-1
08/13/2001
E
ERD (TST 6049)
Wind Uplift
11776.06.02
01/16/2003
E
ERD (TST 6049)
Wind Uplift
P1740.01.07
01/04/20.07
E
ERD (TST 6049)
ASTM D1970
P5130.04.07-1
04/11/2007
E
ERD (TST 6049) -
Wind Uplift
P9260.03.08
03/21/2008
E
ERD (TST 6049)
Wind Uplift
P30540.11.09 -R1
11/30/2009
E
ERD (TST 6049)
Tensile Adhesion
P11030.11.09-1
11/30/2009
E
_. ERD (TST 6D49)___
Wind Uplift
P11030.11.09-2
11/30/2002
E
ERD (TST 6049)
ASTM D4977
P11030.11.09-3
11/30/2009
E
Standard
Year
FM 4474
2011
UL1897
2012
ASTM D226
2009
ASTM D1970
2015
FRSA/TRI April 2012
2012
ASTM D6163
2008
ASTM D6164
2011
ASTM D6222
2011
ASTM D6509
2009
ASTM D4798
2011
Enti
RD
RD
RD
ER
ERDRD
RD
RD
RD
Examination
Reference
Date
(TST 6049)
ASTM D1970
PLYG-SC10130.06.16-1
06/27/2016
(TST 6049)
Tensile adhesion
PLYG-SC30130.06.16-2
06/27/2016/27/
(TST 6049)
TAS 103
PLYG-SC10130.06.16-3
062.016
6049)
ASTM D1970/D4798
PLYG-SC8080.07.16
07/16/2016
(TST 6049)
Wind Uplift
PLYG-SC12025.10.16
102/2016
(TST 6049)
TAS 103
PLYG-SC13040.12.16
12/27/2016
(TST 6049)
30/90 physicals
PLYG-SC11900.03.17
03/10/2017
(TST 6049) - ___
TAS 103
PLYG-SC12115.08.17
08)08/2017
RD(TST 6049)
TAS 103
PLYG-SC13035.08.17
10/31/2017
ERD (TST 6049)
ASTM D1970
P33360.06.10
06/25/2010
FM (TST 1867)
Wind Uplift
3004091
01/12/2000
ERD (TST 6049)
TAS 103
P33370.03.11
03/02/2011
ICC -ES (EVL 2396)
IBC Compliance
ESR -1697
04/01/2019
ERD (TST 6049)
Tensile Adhesion
P33370.04.11
04/26/2011
M -D (CER 1592)
HVHZ Compliance
NOA 17-0614.22
07/06/2017
ERD (TST 6049)
ASTM D1970
P37300.10.11
10/19/2011
MTI (TST 2508)
ASTM D4798
JX20H7A
04/01/2008
ERD (TST 6049)
TAS 103
P40390.08.12-1
08/06/2012
NEMO (TST 6049)
= ASTM D1970
4-PLYG-18-004.03.18
03/29/2018
6049)=—iEnsde-Adhesion--X40390.88-2=3-------08107/3'ft13
1`tE1V1(-I — Wind-Uphft — —m4t-PLYG--180@393 3
ERD (TST 6049)
Tensile Adhesion
641420.09.12-3
09/11/2012
NEMO (TST 6049)
ASTM 06163
45-PLYG-18 002.01.19-A
01/2412019
ERD (TST 6049)
Wind Uplift
P39680.03.13
03/04/2013
NEMO (TST 6049)
ASTM D6222
45-PLYG-18-002.05.19-C
05/20/2019
ERD (TST 6049)
ASTM D1970
P45370.04.13
04/26/2013
NEMC) (TST 6049)
ASTM D1970
4j-PLYG-I9-SSUDL-00.A
09/10/2019
ERD (TST 6049)
Wind Uplift
P1738.02.07 -R2
04/29/2013
NEMO (TST 6049)
TAS 103
4S-PLYG-18-004.10.19-G
10/08/2019
ERD (TST 6049)
Wind Uplift
11757.04.01-1-R1
04/30/2013
NEMO (TST 6049)
TAS 103
4S-PLYG-18-004.10.19-1
10/08/2019
ERD (TST 6049)
ASTM D6164
P37590.03.13 -3A
05/06/2013
NEMO (TST 6049)
TAS 103
4S-PLYG-18-004.10.19-L
10/09/2019
ERD (TST 6049)
ASTM D6509
P37590.03.13 -1-R1
06/26/2013
NEMO (TST 6049)
TA5 103
4j-PLYG-I9-SSUDL-01.A
10/10/2019
ERD (TST 6049)
Wind Uplift
P41630.08.13
08/06/2013
NEMO (TST 6049)
TA5 103
4j-PLYG-I9-SSUDL-02.A
01/02/2020
ERD (TST 6049)
ASTM D4601
P45940.09.13
09/04/2013
NEMO (TST 6049)
ASTM D1970
4S-PLYG-18-004.01.20.H
01/14/2020
ERD (TST 6049)
Wind Uplift
P11751.05.03 -R1
11/26/2013
NEMO (TST 6049)
ASTM D1970
45-PLYG-18-004.01.20.K
01/14/2020
ERD (TST 6049)
Wind Uplift
P11781.11.03 -R1
11/26/2013
NEMO (TST 6049)
TAS 103
4j-PLYG-20-SSUDL-01
07/06/2020
ERD (TST 6049)
30/90 physicals
P45270.05.14
05/12/2014
I PRI (TST 5878)
Tensile Adhesion
PRID1111
04/08/2002
ERD (TST 6049)
Tensile adhesion
6020.09.14-5
09/08/2014
PRI (TST 5878)
TAS 103
PUSA-018-02-01
07/14/2003
ERD (TST 6049)
Tensile adhesion
6020.09.14-6
09/08/2014
PRI (TST 5878)
TAS 103
PUSA-035-02-01
09/29/2006
ERD (TST 6049)
Tensile adhesion
P46520.10.14
10/03/2014
PRI (TST 5878)
TAS 103
PUSA-055-02-02
12/10/2007
ERD (TST 6049)
ASTM D1970/D4798
P43290.10.14
10/17/2014
PRI (TST 5878)
ASTM D6222
PUSA-061-02-02
01/28/2008
NEMO ETC, LLC. Evaluation Report P12060.02.09 -R26
Certificate afAuthorization #32455 CH EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 2 of 16
Entity
Examination
Reference
Date
Entity
Examination
ERD (TST 6049)
TAS 103
PLYG-SC7550.03.15
03/24/2015
PRI (TST 5878)
ASTM D6164
ERD (TST 6049)
Tensile adhesion
P40390.04.15
04/03/2015
Polyglass USA
P/L Affidavit
ERD (TST 6049)
TAS 103
P44360.10.14-111
05/18/2015
Polyglass USA
Materials Affidavit
ERD (TST 6049)
Wind Uplift
PLYG-SC8905.05.16-1
05/17/2016
UL (QUA9625)
Quality Control
4. PRODUCT DESCRIPTION:
Product
4.1 Elastobase
4.2 Elastobase P
4.3 Elastoflex S6 G
4.4 1 Elastoflex S6 G FR
4.5 1 Mule -Hide SA -APP Cap Sheet
4.6 HydraGuard Dual Pro
i
4.7 HydraGuard Tile Pro
4.8 Mule -Hide SA -APP Cap Sheet
)l ---
4.9 =-Polyflex G - - _
4.10 1 Polyflex G FR
Specification
ASTM D6163
ASTM D6164_
ASTM D6164
FRSA/TRI April 2012
ASTM D6164
FRSA/TRI April 2012
ASTM D6222
FRSA/TRI April 2012
ASTM D1970
ASTM D1970
TAS 103
FRSA/TRI April 2012
ASTM D6222
FRSA/TRI April 2012
ASTM D6222
FRSA/TRI April 2012
ASTM D6222
FRSA/TRI April 2012
4.15 Polystick IR -Xe
4.16 Polystick MTS Plus
ASTM D1970
fONEMOjetc.
Reference Date
PUSA-088-02-01 07/29/2009
Mule -Hide Cross Ltg 03/01/2008
Polystick Compound 08/18/2011
Service Confirmation 09/13/2018
Plant(s) Description
FL Fiberglass -reinforced, SBS modified bitumen base sheet
FL Polyester -reinforced, SBS modified bitumen base sheet
FL Polyester -reinforced, SBS modified bitumen cap sheet
FL I Polyester -reinforced, SBS modified bitumen cap sheet
FL Polyester -reinforced, APP modified bitumen cap sheet
FL Nominal 60 -mil thick dual -layer rubberized asphalt
waterproofing membrane, fiberglass reinforced, with a
polyester fabric surface
FL Nominal 60 -mil thick dual -layer rubberized asphalt
waterproofing membrane, fiberglass reinforced, with a
polyester fabric surface
FL Polyester -reinforced, APP modified bitumen cap sheet
FL Polyester -reinforced, APP modified bitumen cap sheet for
use as an alternate to Heat Applied "Cap Sheet" in the
"Two Ply System" from FRSA/TRI April 2012 (04-12)
beneath mechanic -ally fastened or adhered tile roof
systems
FL Polyester -reinforced, APP modified bitumen cap sheet for
use as an alternate to Heat Applied "Cap Sheet" in the
"Two Ply System" from FRSA/TRI April 2012 (04-12)
beneath mechanically fastened tile roof systems
_FC-aly Wer-reinfori;etl, ApP r�odi#ie n cam _—,
-FL -Polyes er-rein orce�A-PP mo ified-bi!sumen cap si7-e-et
FL Fiberglass -reinforced, APP modified bitumen base sheet
AL Fiberglass -reinforced, asphaltic base sheet
FL, PA Nominal 60 -mil thick rubberized asphalt waterproofing
membrane, glass fiber reinforced, with an aggregate
.._C ---
ASTM D1970 FL, NV, Nominal 60 -mil thick rubberized asphalt waterproofing
TAS 103 PA, TX membrane, glass fiber reinforced, surfaced with
FRSA/TRI April 2012 polyolefinic film surface
NEMO ETC, LLC. Evaluation Report P12060.02.09-1126
Certificate of Authorization 1132455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 3 of 16
-'47 Pai�frex"5A P
-—S6222--
FRSA/TRI April 2012
-432 P-olyfe1 x SA P FR
ASTM -D6222
FRSA/TRI April 2012
4.13 Polyglass Base
ASTM D6509
4.14 Polyglass G2 Base Sheet
ASTM D4601
4.15 Polystick IR -Xe
4.16 Polystick MTS Plus
ASTM D1970
fONEMOjetc.
Reference Date
PUSA-088-02-01 07/29/2009
Mule -Hide Cross Ltg 03/01/2008
Polystick Compound 08/18/2011
Service Confirmation 09/13/2018
Plant(s) Description
FL Fiberglass -reinforced, SBS modified bitumen base sheet
FL Polyester -reinforced, SBS modified bitumen base sheet
FL Polyester -reinforced, SBS modified bitumen cap sheet
FL I Polyester -reinforced, SBS modified bitumen cap sheet
FL Polyester -reinforced, APP modified bitumen cap sheet
FL Nominal 60 -mil thick dual -layer rubberized asphalt
waterproofing membrane, fiberglass reinforced, with a
polyester fabric surface
FL Nominal 60 -mil thick dual -layer rubberized asphalt
waterproofing membrane, fiberglass reinforced, with a
polyester fabric surface
FL Polyester -reinforced, APP modified bitumen cap sheet
FL Polyester -reinforced, APP modified bitumen cap sheet for
use as an alternate to Heat Applied "Cap Sheet" in the
"Two Ply System" from FRSA/TRI April 2012 (04-12)
beneath mechanic -ally fastened or adhered tile roof
systems
FL Polyester -reinforced, APP modified bitumen cap sheet for
use as an alternate to Heat Applied "Cap Sheet" in the
"Two Ply System" from FRSA/TRI April 2012 (04-12)
beneath mechanically fastened tile roof systems
_FC-aly Wer-reinfori;etl, ApP r�odi#ie n cam _—,
-FL -Polyes er-rein orce�A-PP mo ified-bi!sumen cap si7-e-et
FL Fiberglass -reinforced, APP modified bitumen base sheet
AL Fiberglass -reinforced, asphaltic base sheet
FL, PA Nominal 60 -mil thick rubberized asphalt waterproofing
membrane, glass fiber reinforced, with an aggregate
.._C ---
ASTM D1970 FL, NV, Nominal 60 -mil thick rubberized asphalt waterproofing
TAS 103 PA, TX membrane, glass fiber reinforced, surfaced with
FRSA/TRI April 2012 polyolefinic film surface
NEMO ETC, LLC. Evaluation Report P12060.02.09-1126
Certificate of Authorization 1132455 6TH EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 3 of 16
4. PRODUCT DESCRIPTION:
Product
4.17 Polystick MU -X
4.18 I Polystick TU Max
4.19 1 Polystick TU P
4.20 1 Polystick TU Plus
4.21 Polystick XFR
Specification
ASTM D1970
(See Section 5.8)
ASTM D1970
TAS 103
FRSA/TRI April 2012
TAS 103
FRSA/TRI April 2012
ASTM D1970
TAS 103
FRSA/TRI April 2012
ASTM D1970
TAS 103
FRSA/TRI April 2012
ONEMOletc.
Plant(s) Description
FL, NV, PA Nominal 54 -mil thick dual -layer rubberized asphalt
waterproofing membrane, fiberglass reinforced, with a
polypropylene film surface
FL, PA, TX Nominal 60 -mil thick rubberized asphalt waterproofing
membrane with a 190 g/m2 polyester fabric surface
TX Nominal 130 -mil thick rubberized asphalt waterproofing
membrane, glass-fiber/polyester reinforced, with a
granular surface
FL, PA Nominal 80 -mil thick rubberized asphalt waterproofing
membrane, glass fiber reinforced, with a polyester fabric
surface
NV Nominal 80 -mil thick rubberized asphalt waterproofing
membrane, glass fiber reinforced, surfaced with a
textured film surface
I I. I — J
5. LIMITATIONS:
5.1 This is a Building Code Evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for
any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless
retained specifically for that purpose.
5.2 This Evaluation Report is not for usejn:f_$C High Velocity Hurricane Zone jurisdictions (i.e., Broward and7h -.ami-Dade Counties).
5.3 This Evaluation Report does not include evaluation of fire classification. Refer to FBC 1516 for requirements and limitations
regarding roof assembly fire classification. Refer to FBC 2603 for requirements and limitations concerning the use of foam plastic
insulation.
--5.4 Polyglass Roof Underlayments may be -used with any prepared roof cover where the product is specifically referenced within
FBC approval documents. If not listed_ , a request may be made to the Authority Having Jurisdiction for approval based on this
evaluation combined with supporting data for the prepared roof covering.
5.5 Allowable Roof Covers:
— Underlayment
Elastobase
Elastobase P
Polyglass Base
TABLE 1: ROOF COVER OPTIONS
Clay and -Concrete TileMetal
A�rfia � r-
5Wingles 1soz3J
(1507.2) Mechanical Adhesive -Set Panels Shingles
— —Attach —(1507.4) —(15075)
Yes Yes
Yes (Base Sheet in 2 -ply (Base Sheet in 2 -ply Yes Yes
Yes
No
Polyglass G2 Base No
Elastoflex S6 G Yes
Elastoflex S6 G FR Yes
HydraGuard Dual Pro Yes
NEMO ETC, I.I.C.
Certificate of Authorization 1132455
6T" EDITION (2017) FBC NON-HVHZ EVALUATION
Polyglass Roof Underlayments; (954) 233-1230
Yes
No
system)
system)
Shingles
__'15D7_ -9J..
Shakes
—(15074 -
Yes
Yes
No
Yes
(Base Sheet in 2 -ply
(Base Sheet in 2 -ply
Yes
system)
system)
Yes
Yes
(Base Sheet in 2 -ply
(Base Sheet in 2 -ply
No
system)
system)
Yes
Yes
(Base Sheet in 2 -ply
(Base Sheet in 2 -ply
No
system)
system)
Yes
Yes
(See 5.5.1)
No
Yes
No
No
No
No
Yes
6T" EDITION (2017) FBC NON-HVHZ EVALUATION
Polyglass Roof Underlayments; (954) 233-1230
Yes
No
No I No I No
No No No No
No Yes No No
No Yes No No
Yes Yes Yes Yes
Evaluation Report P12060.02.09 -R26
FL5259-R30
Revision 26: 07/06/2020
Page 4 of 16
---mod —
-----—
--Sfingies
(1507.7)
Shingles
__'15D7_ -9J..
Shakes
—(15074 -
Yes
No
No
Yes
No
No
No I No I No
No No No No
No Yes No No
No Yes No No
Yes Yes Yes Yes
Evaluation Report P12060.02.09 -R26
FL5259-R30
Revision 26: 07/06/2020
Page 4 of 16
5.5.1
NNEMOIetc.
TABLE 1: ROOF COVER OPTIONS
Asphalt
Clay and Concrete Tile
Metal
Slate
Wood
Underlayment
Shingles
(1507.3)
Shin les
Mechanical
Adhesive -Set
Panels
Shingles
Shingles
Shakes
(1507.2)
fISO 7)
Attach
(1507.4)
(1507.5)
(1507.8)
(1507.9)
HydraGuard Tile Pro
Yes
Yes
Yes
(See 5.5.1)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
(See 5.S.1)
No
No
Yes
No
No
Mule -Hide SA -APP Cap Sheet
Mule -Hide SA -APP Cap Sheet (FR)
Yes
Yes
(See es
No
No
Yes
No
No
Polyflex G
Yes
Yes
(See es
5.Polyflex
No
No
Yes
No
No
G FR
Yes
Yes
Yes
Yes
No
Yes
(See 5.5.1)
No
No
Yes
No
No
Polyflex SA P
_
No
No
Yes
No
No
Yes
Yes
Yes
No
Yes
(See 5.5.1)
No
No
No
No
Yes
No
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Polyflex SA P FR
Polystick IR -Xe
Polystick MTS Plus
Yes
Yes
Polystick MU -X
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Polystick TU Max
_
No
Yes
Yes
(See 5.5.1)
Yes
No
Yes
No
No
No
Yes
Yes
Yes
Yes
Polystick TU P No
Yes
Yes
(See 5.5.1)
Yes Yes
(See 5.5.1)
Yes
Yes
Yes
Yes
Yes
Polystick TU Plus Yes
Polystick XFR Yes
Yes
Yes
Yes
Yes No
Yes
Yes
"Adhesive -set Tile" is limited to use of the fol lowing_Approved tile :adhesives / underlayment combinations.
TABLE 1A: ALLOWABLE TILE ADHESIVE / UNDERLAYMENT COMBINATIONS'
Florida Product f
-Ti Adhesive Approval— Underlayments
DAPFoam "Touch 'n Seal StormBond
Roof Tile Adhesive" FL14506 Polystick TU Max or Polystick TU Plus
Dupont "TILE BONDTm Roof Tile FL22525 HydraGuard Tile Pro, Polyflex SA P, Polystick TU Max, Polystick TU P or
Adhesive" Polystick TU Plus
ICP Adhesives and Sealants "Polyset®
7CP eA�i lives andSealanfs176yset0'
RTA -1"
FL6276
Elastoflex S6 G, HydraGuard Tile Pro, Mule -Hide SA -APP Cap Sheet, Mule -
Hite SA-APP---al-heet-(F-R); Polyflex-G, Paiyfiex'jA-P, Polyflex-%�fR,
i] _M...i.�..l.-Tt-f - ..- .-- -- __-T.____
Elastoflex.56 G, HydraG-uar-d Tile Pro, Mele-Hide-SA-APP Cap Sheet, Mule ---
Hide SA -APP Cap Sheet (FR), Polyflex G, Polyflex SA P, Polyflex SA P FR,
Polystick TU Max, Polystick TU Por Polystick TU Plus
1 Refer to Tile Manufacturer's or Adhesive Manufacturer's Florida Product Approval for Overturning Moment Resistance Performance,
NEMO ETC, LLC. Evaluation Report P12060.02.09 -R26
Certificate of Authorization #32455 6- EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 5 of 16
ONEMOletc.
5.6 Allowable Substrates:
TABLE 2: SUBSTRATE OPTIONS FOR ADHERED UNDERLAYMENTS
Substrates (designed to meet wind loads for project)
Underlayment Application
Type Primer Materials)
Deck / (Optional) ASTM D41 plywood, OSB, Southern Yellow Pine or Huber
HydraGuard Dual Pro, Engineered Woods "ZIP System" Panels
HydraGuard Tile Pro, sheathing -
ASTM D41 structural concrete
Polystick (all variations), self- ASTM C1289 Type II Class 1 polyisocyan u rate, ASTM
Mule -Hide SA -APP Cap adhering Insulation (Optional) ASTM D41 C1289 Type V polyisocyanurate-composite, DensDeck
Sheet, Mule -Hide SA -APP or WB -3000
Cap Sheet (FR), Polyflex Prime or SECUROCK Gypsum -Fiber Roof Board
SA P or Polyflex SA P FR Base N/ A ASTM D226 felt, Elastobase, Elastobase P or Mule -Hide
Sheet Nail Base
Deck ASTM D41 structural concrete
Elastoflex S6 G or Insulation (Optional) ASTM D41 DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board
hot asphalt -
Elastoflex S6 G FR Base N/A ASTM D226 felt, Elastobase, Elastobase P, Mule -Hide Nail
Sheet Base or Polyglass G2 Base
Deck ASTM D41 structural concrete
Polyflex G or Polyflex G FR torch- Insulation (Optional) ASTM D41 DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board
applied Base Elastobase, Elastobase P, Mule -Hide Nail Base, Polyglass
Sheet N/A G2 Base or Polyglass Base
5.6.1 Wind Resistance for Underlayment Systems in Adhesive -set Tile Aa lications:
The following wind uplift limitations apply to underlayment systems that are not prescriptively addressed in FRSA/TRI April
2012 (04-12) and are used in adhesive -set or mortar -set tile applications. Maximum Design Pressure is the result of testing
for wind load resistanze-based on -allowable wind loads and reflects the ultimate passing pressure divided by 2 (the 2 to 1
margin of safety per-fBC 1504.9 has already been applied). Refer to FRSA/TRI April 2012-(04-12), Appendix A, Table 1A or FBC
1609 for determination of design wind loads.
#1 Maximum Desip n Pressure = -52.5 psf:
Deck: APA rated, 7/16 CAT, 0.418 im-,-Exposure 1, OSB sheathing to meet project requirements to satisfaction -of -Authority Having
Jurisdiction.
Joints: Min. 4 -inch wide strips of Elastoflex SA -V over all OSB joints
Base Ply: Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#2 Maximum Design Pressure=-
- Deck: Min-1-5M--inch-plywood-to-meet-pmject r-equir menu ro satisfaction of Autha its Hav ng!urisdictaon. --- - —
Primer: None
Base-Piy. (Optional)-Polystick-MTS-Plus,-setfiadheyed.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#3 Maximum Desip-n Pressure = -97.5 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG 100 or ASTM D41
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered and back -nailed within the selvedge -edge side laps using 12 ga. x IV ring shank nails
through 32 ga., 1-5/8" diameter tin caps spaced 12 -inch o.c.
NEMO ETC, I.I.C. Evaluation Report P12060.02.09 -R26
Certificate of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 6 of 16
ONEMOletc.
#4 Maximum Design Pressure = -105 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: WB -3000
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered and back -nailed within the selvedge -edge side laps using 12 ga. x 1Y" ring shank nails
through 32 ga., 1-5/8" diameter tin caps spaced 12 -inch o.c.
#5 Maximum Design Pressure = -135 nsf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: (Optional) PG100 or ASTM D41
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Joints: Min. 4 -inch wide strips of Elastoflex SA -V over all plywood joints.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#6 Maximum Design Pressure= -315 psf:
Deck: Structural concrete to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG 100 or ASTM D41
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: HydraGuard Tile Pro, Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR,
Polystick TU Max, Polystick TU P or Polystick TU Plus, self -adhered.
#7 Maximum Design Pressure = -622.5 psf:
Deck: Structural concrete to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG 100 or ASTM D41
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#8 Maximum Design Pressure = -30.0 sf*:
Deck: Min. 15/32 -inch OSB to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hi i atl Base (poly -film top surface)
Fasteners: 11 ga. x 1.25 -inch longx_1-inch head diameter round metal cap nails
Spacing: 6 -inch o.c. at the 3 -inch wide side laps and 6 -inch o.c. at two (2) equally spaced staggered center r6ws. -
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plumsself-adhered. --- --
#9 Maximum Design Pressure = -37.5 psf*:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: 11 ga. x 1.25 -inch long x 1 -inch head diameter round metal cap nails
Spacing: 6 -inch o.c. at the 3 -inch wide side laps and 6 -inch o.c. at two (2) equally spaced staggered center rows.
B�e_Eht: _(Qptional) PolWick MTS PJu5- s_j0f-adhered. - - --
- U-nderKayment- M-ule-Hide-SA-A-P-P-Cip-Sheet� Mule -Hide -S 4 RCap—Sheet-EF-Rl,-R SA-PTPelyflex3A RfR 4ystic-k-T-U-Max P4ystick --- -
TU P or Polystick TU Plus, self -adhered.
#10 Maximum Design Pressure = -37.5 psf*:
Deck: Min. 19/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: One (1) or two (2) layers ASTM D226, Type II felt
Fasteners: 11 ga. x 1.25 -inch long x 1 -inch head diameter round metal cap nails
Spacing: 6 -inch o.c. at the 3 -inch wide side laps and 12 -inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt.
NEMO ETC, LLC. Evaluation Report P12060.02.09 -R26
Certificate ofAuthorization 1131455 CH EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 7 of 16
ONEMOletc.
#11 Maximum Design Pressure = -45 psf*:
Deck: Min. 19/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: One (1) layer ASTM D226, Type II felt
Fasteners: 11 ga. x 1.25-inch x 3/8-inch head diameter annular ring shank roofing nails at 1-5/8-inch diameter tin caps
Spacing: 4-inch o.c. at the 2-inch wide side laps and 4-inch o.c. at two (2) equally spaced staggered center rows.
Base Ply: (Optional; for use with self-adhering underlayment only) Polystick MTS Plus, self-adhered.
Underlayment: Mule-Hide SA-APP Cap Sheet, Mule-Hide SA-APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self-adhered.
#12 Maximum Design Pressure = -45 psf*:
Deck: Min. 19/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Two (2) layers ASTM D226, Type II felt
Fasteners: 11 ga. x 1.25 -inch long x 3/8 -inch head diameter annular ring shank roofing nails at 1 -5/8 -inch diameter tin caps
Spacing: 9 -inch o.c. at the 2 -inch wide side laps and 9 -inch o.c. at two (2) equally spaced staggered center rows.
Base Ply: (Optional; for use with self -adhering underlayment only) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered or Elastoflex S6 G, applied in full mopping of hot asphalt.
#13 Maximum Design Pressure = -45 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 9 -inch o.c. at the 2 -inch wide side laps and 18 -inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex 56 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#14 Maximum Design Pressure= -45.0psf:
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasten=:- 12 ga. annular ring shank nails with 1-5/8" diameter tin caps --
Spacing: 6-inch_o.c. at the 3 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#15 Maximum Design Pressure =-45.0 psf:
Deck: - APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase (sand top surface)
Fasteners: 12 ga. annular ring shank nails with 1-5/8" diameter tin caps
Spacing: 6 -inch o.c. at the 3 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G,—applied in full mopping of hot asphalt.
#I&- -Maximu-m Des fg n—Pressure"= 45:0 psf: -- — "
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Polyglass Base
Fasteners: 12 ga. annular ring shank nails with 1-5/8" diameter tin caps
Spacing: 6 -inch o.c. at the 3 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Polyflex G, torch -applied.
#17 Maximum Design Pressure = -52.5 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 9 -inch o.c. at the 2 -inch wide side laps and 12 -inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
NEMO ETC, I.I.C. Evaluation Report P12060.02.09 -R26
Certificate of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 8 of 16
ONEMOletc.
#18 Maximum Design Pressure = -52.5 sf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: Simplex Original Cap Nails
Spacing: 6 -inch o.c. at the 3 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#19 Maximum Design Pressure = -52.5 sf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: Simplex Original Cap Nails
Spacing: 6 -inch o.c. at the 3 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#20 Maximum Design Pressure = -60 sf:
Deck: Min. 19/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: 11 ga. x 1.25 -inch long x 3/8 -inch head diameter annular ring shank roofing nails at 1 -5/8 -inch diameter tin caps
Spacing: 8 -inch o.c. at the 4 -inch wide side laps and 8 -inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#21 Maximum Design Pressure 7 -60 sf:
Deck: Min. 19/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: OMG #12 Standard Roofgrip with OMG Flat Bottom Metal Plates
Spacing: 12 -inch o.c. at the 4 -inch wide side laps and 12 -inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#22 Maximum Design Pre=re = -60.0 Dsf:
Deck: APA rated, 7/16 CAT, 0,418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction. - - -
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 8 -inch. at the 3 -inch wide side laps and 8 -inch o.c. at three (3) equally spaced -staggered center rows.
Primer: PG100 or ASTM D41 primer applied to stress plates.
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#23 Maximum Design Pressure = -60.0 sf:
Deck: APA rated. 7116LAT. 0.4188 in__'�xoosw , QSB sheathine to mee oroject reouireme
�.. gt��.Q_Sgtl,Sfa_ction oTAuthority Hay1Og
Jurisdiction.
Base Sheet: Elastobase (sand top surface)
F—asteners: SimjarexNIAXX Cap Fasteners
Spacing: 8 -inch o.c. at the 3 -inch wide side laps and 8 -inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt.
#24 Maximum Design Pressure =-60.0 DO:
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Polyglass Base
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 8 -inch o.c. at the 3 -inch wide side laps and 8 -inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Polyflex G, torch -applied.
NEMO ETC, I.I.C. Evaluation Report P12060.02.09 -R26
Certificate of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 9 of 16
ONEMOletc.
#25 Maximum Design Pressure = -67.5:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Polyglass G2 Base or Polyglass Base (requires use of torch -applied underlayment)
Fasteners: 12 ga. x 1.25 -inch long x 3/8 -inch head diameter annular ring shank roofing nails at 1 -5/8 -inch diameter tin caps
Spacing: 8 -inch o.c. at the 4 -inch wide side laps and 8 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or torch -applied or Polyflex G, torch -applied.
#26 Maximum Design Pressure = -67_.5 psf:
Deck: APA rated, 19/32 CAT, 0.578 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 180° into the holes of the plate, parallel to
the width direction of the sheet.
Spacing: 12 -inch o.c. at the 4 -inch wide side laps and 12 -inch o.c. at two (2) equally spaced staggered center rows.
Primer: (Optional) PG100 or ASTM D41 primer applied to stress plates.
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#27 Maximum Design Pressure= -67.5 psf:
Deck: APA rated, 19/32 CAT, 0.578 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase (sand top surface)
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 180° into the holes of the plate, parallel to
the width direction of the sheet.
Spacing: 12 -inch o.c. at the 4 -inch wide side laps and 12 -inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt.
#28 Maximum Design Pressure = -67.5 psf:
- Deck: _ -- APA rated, 19/32 CAT, 0.578 in., Exposure 1, OSthing to meetprojectrequirements to satisfaction of Authority Having
_ Jurisdiction. _
Base Sheet: Elastobase or Polyglass Base
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 180° into the holes of the plate, parallel to
the width direction of the sheet.
— Spacing: - 12 -inch o.c. at the 4 -inch wide side laps and 12 -inch o.c. at two (2) equatly spaced staggered center rows.
Underlayment: Polyflex G, torch -applied.
#29 Maximum Design Pressure =-75.psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Polyglass G2 Base or Polyglass Base (requires use of torch -applied underlayment)
Fasteners: Dekfast #14 with Dekfast Hex plates, OMG #14 HD with OMG 3" Galvalume Steel Plates, OMG Roofgrip #14 with OMG Flat
"-Bottom Plates AccuTrac , Trufast HD with Trufast 3 -inch Insulation Plate3-or Simplex MAXXCarr Fasteners
--- _ spacing:- --inch-or- at -the -finch -wide cid aps-and-lD-4nch-o.c�t#-hree�3) equaUy-spaced-staggzr-ed-re-atex-ro+r_s�
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or torch -applied or Polyflex G, torch -applied.
#30 Maximum Design Pressure= -90 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 6 -inch o.c. at the 2 -inch wide side laps and 6 -inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#31 Maximum Design Pressure = -90 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3" Round Metal Plates or OMG Flat Bottom Metal Plates
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
NEMO ETC, LLC. Evaluation Report P12060.02.09 -R26
Certificate of Authorization #32455 6- EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 10 of 16
ONEMOletc.
#32 Maximum Design Pressure = -90 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface)
Fasteners: Trufast #12 DP or Trufast #14 HD with Trufast 3" Metal Insulation Plates
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt.
#33 Maximum Design Pressure =-90.,psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Polyglass G2 Base or Polyglass Base (requires use of torch -applied underlayment)
Fasteners: Dekfast #14 with Dekfast Hex plates, OMG #14 HD with OMG 3" Galvalume Steel Plates, OMG Roofgrip #14 with OMG Flat
Bottom Plates (AccuTrac), Trufast HD with Trufast 3 -inch Insulation Plates or Simplex MAXX Cap Fasteners
Spacing: 9 -inch o.c. at the 4 -inch wide side laps and 9 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or torch -applied or Polyflex G, torch -applied.
#34 Maximum Design Pressure = -90.0 psf:
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 180" into the holes of the plate, parallel to
the width -direction of the sheet
Spacing: 9 -inch o.c. at the 2 -inch wide side laps and 12 -inch o.c. at two (2) equally spaced staggered center rows.
Primer: PG100 or ASTM D41 primer applied to stress plates.
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#35 Maximum Design Pressure = -90.0 Dsf:
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction...
Base Sheet: Elastobase (sand top surface)
Fasten=ers: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 18b" into the holes of the plate, parallel to
the width -direction of the sheet
Spacing: 9 -inch o.c. at the 2 -inch wide side laps and 12 -inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex S6 -G, -applied in full mopping of hot asphalt.
#36 Maximum Design Pressure= -90.0p :
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Polyglass Base
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 180° into the holes of the plate, parallel to
the width -direction of the sheet
Spacing: 1 -inch o.c. at tr+e 2. -inch wide si eland 1?-Ynch o- at two (equally space&staggere center rows:
Underlayment: Polyflex G, torch -applied.
#37 --Maximum = - 7-.5—psf:
Deck: Min. 19/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: 11 ga. x 1.25 -inch x 3/8 -inch head diameter annular ring shank roofing nails at 1 -5/8 -inch diameter tin caps
Spacing: 4 -inch o.c. at the 4 -inch wide side laps and 4 -inch o.c. at four (4) equally spaced staggered center rows.
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
NEMO ETC, LLC. Evaluation Report P12060.02.09-1126
Certificate of Authorization #32455 6T" EDITION (2017) FBC NON-HVH2 EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 11 of 16
ONEMO I etc.
#38 Maximum Desi n Pressure --97.5psf:
Deck: APA rated, 19/32 CAT, 0.578 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Primer: PG100 or ASTM D41 primer applied to stress plates.
Base Ply: (Optional) Polystick MTS Plus, self -adhered.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#39 Maximum Design Pressure = -97.5 psf:
Deck: APA rated, 19/32 CAT, 0.578 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase (sand top surface)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt.
#40 Maximum Desii?n Pressure = -97.5 psf:
Deck: APA rated, 19/32 CAT, 0.578 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Polyglass Base
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Polyflex G, torch -applied.
#41 _Maximum Design Pressure = -105 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface#udant-asphalt orxor-ch-applied cap or poly -film surface for torch -applied C314---= _ —
Fasteners: Simplex MAXX Cap Fasteners
- Spacing: 6 -inch o.c. at the 2 -inch wide side laps and 6 -inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex 56 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#42 Maximum Design Pressure = -105.0 psf: _
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction. - -
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 180° into the holes of the plate, parallel to
the width -direction of the sheet
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at three (3) equally spaced staggered center rows.
Primer: g PG100 or ASTM D41_primer applied to stress plates. ---
-�---R=se-Pl - — Optional)-P-olystack-MTS-Plus, ff--atfhe-red.
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P, Polyflex SA P FR, Polystick TU Max, Polystick
--TtiH3-orPolystick-T-U-Plus, seif--a-dhemd.
#43 Maximum Design Pressure = -105.0 psf:
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing.to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase (sand top surface)
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 180° into the holes of the plate, parallel to
the width -direction of the sheet
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex 56 G, applied in full mopping of hot asphalt.
NEMO ETC, LLC. Evaluation Report P12060.02.09-1126
Certificate of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 12 of 16
ONEMOletc.
#44 Maximum Design Pressure = -105.0 psf:
Deck: APA rated, 7/16 CAT, 0.418 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet: Elastobase or Polyglass Base
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with two (2) screws per plate installed 180° into the holes of the plate, parallel to
the width -direction of the sheet
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Polyflex G, torch -applied.
#45 Maximum Design Pressure = -112.5 psf:
Deck: Min. 19/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: 11 ga. x 1.25 -inch x 3/8 -inch head diameter annular ring shank roofing nails at 1 -5/8 -inch diameter tin caps
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at four (4) equally spaced staggered center rows.
Primer: PG100 or ASTM D41 primer at all tin -caps
Base Ply: Polystick MTS Plus, self -adhered
Underlayment: Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P. Polyflex SA P FR, Polystick TU Max, Polystick
TU P or Polystick TU Plus, self -adhered.
#46 Maximum Design Pressure = -120 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3" Round Metal Plates or OMG Flat Bottom Metal Plates
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at five (5) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#47 Maximum Design Pressure = -120 psf:
Deck: Min. 15/32 -inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface)
Fasten_ers:. - Trufast #12 DP or Trufast #14 HD with Trufast 3" MetaOnsulation Plates _
Spacing: 6 -inch o.c. at the 4 -inch wide side laps and 6 -inch o.c. at five (5) equally spaced staggered center rows.
Underlayment: Elastoflex S6 G, applied in full mopping of hot aspFtalt.--
#48 Maximum Design Pressure = -127.5 psf:
Deck: APA rated, 19/32 CAT, 0.578 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
---
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: TRUFAST Versa -Fast Fasteners & Plates with one (1) screw per plate, in the center hole.
Spacing: 9 -inch o.c. at the 4 -inch wide side laps and 9 -inch o.c. at four (4) equally spaced staggered center rows.
Primer: PG100 or ASTM D41 primer applied to stress plates.
Base Ply: (Optional) Polystick MTS Plus, self-adhered.
--Underlayme-nt:=Mule-Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex-SA P, Polyflex SA P FR, Polystick TU Max, Polystick
^--- P or olysticc T U 7 rus; se -a ere
#49 Maximum Desi:2n Pressure = -127.5 nsf:
i7ec
ra e-d-n/32-CAT,-0.578in., Exposure 1; OSB sheathing to meet projeUt requirement -s -to salissf-a-clion o �luihonty Having
Jurisdiction.
Base Sheet:
Elastobase (sand top surface)
Fasteners:
TRUFAST Versa -Fast Fasteners & Plates with one (1) screw per plate, in the center hole.
Spacing:
9 -inch o.c. at the 4 -inch wide side laps and 9 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment:
Elastoflex S6 G, applied in full mopping of hot asphalt.
#50 Maximum Design
Pressure = -127.5 psf:
Deck:
APA rated, 19/32 CAT, 0.578 in., Exposure 1, OSB sheathing to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Base Sheet:
Elastobase or Polyglass Base
Fasteners:
TRUFAST Versa -Fast Fasteners & Plates with one (1) screw per plate, in the center hole.
Spacing:
9 -inch o.c. at the 4 -inch wide side laps and 9 -inch o.c. at four (4) equally spaced staggered center rows.
Underlayment:
Polyflex G, torch -applied.
NEMO ETC, LLC. Evaluation Report P12060.02.09 -R26
Certificate of Authorization #32455 CH EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 13 of 16
ONEM01 etc.
5.6.1.1 All other direct -deck, adhered Polyglass underlayment systems beneath adhesive -set tile systems carry a Maximum Design
Pressure of -45 psf.
5.6.1.2 For mechanically attached Base Sheet, the maximum design pressure for the selected assembly shall meet or exceed that
required under FRSA/TRI April 2012 (04-12), Appendix A, Table 1A.
Alternatively, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design pressure
determined in accordance with FBC 1609. In this case, Zones 2 and 3 shall employ an attachment density designed by a
qualified design professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss
Prevention Data Sheet 1-29 and Roofing Application Standard RAS 117. Assemblies marked with an asterisk* carry the
limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (February 2020) for Zone 2/3 enhancements.
5.7 Exposure Limitations:
TABLE 3: EXPOSURE LIMITATIONS
Underlayment Maximum Exposure (days)
HydraGuard Dual Pro, HydraGuard Tile Pro, Polystick MTS Plus, Polystick TU Max, Polystick TU P, 180
Polystick TU Plus or Polystick XFR
Polystick IR -Xe or Polystick MU -X 90
Elastobase, Elastobase P, Polyglass G2 Base or Polyglass Base 30
180
Elastoflex S6 G, Elastoflex S6 G FR, Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (for adhesive -set tile)
(FR), Polyflex G, Polyflex G FR, Polyflex SA P or Polyflex SA P FR UNLIMITED
(for mechanically fastened roof
prepared roof covers)
5.8 Polystick MU -X has been found through comparative testing to have a lesser coefficient of friction than ASTM D226 roofing
felt in a dry condition, test9d:at Standard laboratory conditions. Agreement between purchas€l--and selle-r;-asset forth in
Section 4.3, Note 1 of ASTMO1970-15, should be established as to slip resistance. —.
5.9 Tile Slippage Limitations FRSA TRI April 2012 04-12
When loading roof tiles on the underlayment in direct -deck tile assemblies, the maximum roof slope shall be as follows. These
slope limitations can only be -exceeded by using battens during loading of the roof tiles.
NEMO ETC, I.I.C. Evaluation Report P12060.02.09 -R26
Certificate o}Authorization #32455 0 EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 14 of 16
TABLE 2: TILE SLIPPAGE LIMITATIONS FOR DIRECT -DECK TILE INSTALLATIONS —
Underlayment
Tile Profile
Staging Method
Maximum Slope
Elastoflex S6 G or S6 G FR
Flat or Lugged
6 -tile stack (4 over 2)
4:12
HydraGuard Tile Pro
Flat or Lugged
6 -tile stack (4 over 2)
7:12
Polyflex G or G FR _
Flat or Lu ed--
6 -tile stack 4 over 2]_
- , 4:12
-Poiyflex SA-P�r-SA P -FR
--Flat-or-Lugged-6
t tel stack -(4 -over -2) — -
--44.2 - — -
Flat
6 -tile stack (4 over 2)
5:12
—"stic-k-MTS-Plus
Lugged
_
6 -tile stack (4 over 2)
4:12
Flat
6 -tile stack (4 over 2) or 30 -tile stack
7:12
Polystick TU Max
Lugged
6 -tile stack (4 over 2)
7:12
Lugged
10 -tile stack
6:12
Flat
6 -tile stack (4 over 2)
6:12
Polystick TU P
Lugged
6 -tile stack (4 over 2)
4:12
Flat or Lugged
6 -tile stack (4 over 2)
7:12
Polystick TU Plus
Flat or Lugged
10 -tile stack
6:12
Polystick XFR
Flat or Lugged
Prohibited without battens
Prohibited without battens
NEMO ETC, I.I.C. Evaluation Report P12060.02.09 -R26
Certificate o}Authorization #32455 0 EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 14 of 16
ONEMO I etc.
6. INSTALLATION: _ ✓._-LL-
6.1 Polyglass Roof Underlayments shall be installed in accordance with Polyglass published installation requirements subject to the
Limitations set forth in Section 5 herein and the specifics noted below.
6.2 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove any dust
and debris prior to application, and prime the substrate (if applicable).
6.3 Elastobase, Elastobase P or Mule -Hide Nail Base:
6.3.1 Non -Tile Ap p lications:
Shall be installed in compliance with the codified requirements for ASTM D226, Type II underlayment in FBC Table 1507.1.1 for
the type of prepared roof covering to be installed and Polyglass published requirements.
Elastobase, Elastobase P or Mule -Hide Nail Base may be covered with a layer of Polystick, Polyflex SAP, Polyflex SA P FR, Mule -
Hide SA -APP Cap Sheet or SA -APP Cap Sheet (FR), self -adhered, Elastoflex S6 G or Elastoflex S6 G FR in hot asphalt or Polyflex G
or Polyflex G FR, torch applied. Roof cover limitations are those are those associated with the top -layer underlayment, as set
forth in Table 1.
6.3.2 Tile Applications:
Elastobase, Elastobase P or Mule -Hide Nail Base are limited to use as a mechanically attached base sheet in the "Two Ply
System" from FRSA/TRI April 2012 (04-12). Reference is made to Table 1 and Section 5.6.1 herein, coupled with FRSA/TRI April
2012 (04-12) Installation Manual.
6.4 HydraGuard Dual Pro, HydraGuard Tile Pro, Mule -Hide SA -APP Cap Sheet, Mule -Hide SA -APP Cap Sheet (FR), Polyflex SA P,
Polyflex SA P FR, Polystick IR -Xe, Polystick MTS Plus, Polystick MU -X, Polystick TU Max, Polystick TU P, Polystick TU Plus or
Polystick XFR:
6.4.1 General: T
All seal -lap seams (selvage laps) must be firmly rolled with a in
--- accordance with Polyglass requirements to ^full contacT—
and adhesion. For HydraGuard Dual Pro and=}HydraGuard Tale
Pro, align the edge of the top sheet to the end of the glue
pattern (the sheet will overlap the fabric).
View of Ovelap Seam of HydraGuard Dual Pro and HydraGuard Tile Pro
_ 6.4.2 ---)on-Tile Applications:
Shall be installed-irr-compiiance-with-the codified requirements -for -ASTM -M70 aymentin-F-BC—Table 1507A. for -the --=--
type of prepared roof covering to be installed and Polyglass published requirements.
6.4.3 Tile Applications jexcludes HydraGuard Dual Pro Polystick 1R -Xe and Pol vstick MU -X1_:
Shall be installed in compliance with the requirements for Self -Adhered Membrane set forth in FRSA/TRI April 2012 (04-12) and
Polyglass published requirements.
For mechanically fastened tile roofing over 2 -ply system, consisting of Base Sheet and self -adhering top sheet(s), Base Sheet
fastening shall be not less than FRSA/TRI April 2012 (04-12), Table 1.
For adhesive -set tile applications, refer to Section 5.6.1 herein.
6.4.4 Multi -Ply Underla ment Systems:
Polystick MTS Plus or Polystick XFR followed by HydraGuard Tile Pro, Polyflex SA P, Polystick MTS Plus, Polystick MU -X, Polystick
TU Max, Polystick TU P, Polystick TU Plus or Polystick XFR is allowable for use under mechanically attached prepared roof
systems. Limits of use are those associated with the top -layer material. This is not a requirement, but is allowable if a 2 -ply
underlayment system is desired.
NEMO ETC, U.C. Evaluation Report P12060.02.09 -R26
Certificate of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 15 of 16
A&lk
WNEMOjetc.
Polystick MTS Plus followed by HydraGuard Tile Pro, Polyflex SA P, Polystick TU Max, Polystick TU P or Polystick TU Plus is
allowable for use under adhesive -set tile systems. Limits of use are those associated with the top -layer material. This is not a
requirement, but is allowable if a 2 -ply underlayment system is desired.
6.5 1 Elastoflex S6 G or Elastoflex S6 G FR:
6.5.1 Elastoflex S6 G or Elastoflex S6 G FR shall be installed in compliance with current Polyglass published installation requirements.
For use in tile applications:
✓ Elastoflex S6 G is for use as an alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single Ply System"
from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems or the Hot Asphalt applied "Cap Sheet"
in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened or adhered tile roof systems.
✓ Elastoflex S6 G FR is for use as an alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single Ply
System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems or the Hot Asphalt applied "Cap
Sheet" in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems.
6.5.2 For hot -asphalt -applications, Elastoflex S6 G or Elastoflex S6 G FR shall be fully asphalt -applied to the substrates noted in Table
2. Side laps shall be minimum 3 -inch and end -laps minimum 6 -inch wide, off -set minimum 3 feet from course to course. Side
and end laps shall be fully adhered in a complete mopping of hot asphalt with asphalt extending approximately 3/8 -inch beyond
the lap edge.
6.6 Polyflex G or Polyflex G FR: 1
6.6.1 Polyflex G or Polyflex G FR shall be installed in compliance with current Polyglass published installation requirements. For use
in tile applications:
✓ Polyflex G is for use as an alternate to the Heat Applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012 (04-
12) beneath mechanically fastened or adhered tile roof systems (Refer to Table 2 for base sheet options).
✓ Polyflex G FR is for use as an alternate to the Heat Applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012
(04-12) beriER mechanicaliyfastened tile roof systems (Refer to Table 2 for base sheet optio-ri= )-.
6.6.2 Polyflex G or Polyflex G FR shall be fully torch -applied to the substrates noted in Table 2. Side laps shall be minimum 3 -inch and
end -laps minimum 6 -inch wide, off -set minimum 3 feet from course to course. Side and end laps shall be fully heat -welded and
inspected to ensure minimum 3/8 -inch flow of modified compound beyond the lap edge.
6.7 Tile Staging:
6.7.1 Tile shall be loaded and staged in a manner that prevents tile slippage and/or damage to the underlayment. Refer to Table 2
herein, and Polyglass published requirements for tile staging.
6.7.2 Battens and/or Counter -battens, as required by the tile manufacturer and FRSA/TRI April 2012 (04-12) must be used on all roof
slopes greater than 7:12. Precautions should be taken as needed, such as the use of battens or nail -boards, to prevent tile
erg -M F%�-dm.._o= ---.e-!ndeFlayfAent-4uririg+ng-pfeee65-.—
7. BUILDING PERMIT REQUIREMENTS: l
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product.
8. MANUFACTURING PLANTS:
Contact the noted QA agency for information on product locations covered for F.A.C. 61G20-3 QA requirements. Refer to
Section 4 herein for product & production locations having met codified physical properties specifications.
9. QUALITY ASSURANCE ENTITY:
UL, LLC– QUA9625; (314) 578-3406; k.chancellor@us.ul.com
- END OF EVALUATION REPORT -
NEMO ETC, U.C. Evaluation Report P12060.02.09 -R26
Certificate ojAuthorization #32455 6T" EDITION (2017) FBC NON-HVH2 EVALUATION FL5259-R30
Polyglass Roof Underlayments; (954) 233-1230 Revision 26: 07/06/2020
Page 16 of 16