HomeMy WebLinkAboutProduct Approval; Garage DoorPRODUCT APPROVAL SUBMITTAL FORM
GARAGE DOOR, Submittal Dale:
°' ,u,l, ►�o For Bldg, Dept. Use Only
ConlroVPermil N:
1.0 Detailed Product Descrlptlon
4.0 Specific Installation Requirement:
1.1 Manufacturer: FINISHLINE INDUSTRIES
4.1 Masonry Openings
at Model Name: 350 NI
b) Model Number:
c) Unit Size: 10 ' - 2 " X 10 ' -1 "
101- 0" X 1011- 0"
d) Rated Unilorm Air Pressure Capacity (Based on Test Data)
t) Negative (psi): 3 0 DESIGN 45 STRUCTTJR
Anchor door at each side with 1/4" die. -
L
_
ff) Positive (psi): 30 DESIGN 45 STRUCTURAL
wedge type bolts such as Hilt) Kwik -
bolts or red head bolts spaced 12"c/c _
e) Impact Resistibility ❑ Yes ❑ No
and embedded 2" into conctrete columns.
—
2.0 Materiel Characteristics
2.1 Door Material (Type and Thickness) _ 1 3/4 ALTJM
4.2 Wood Framed Openings
2.2 Glazing
a) Glazing Material (Type 6 Thickness): 1_/8" DSR rLASS
b) Glazing Method: ALUM SNAP 'IN GLAZING
2.3 Hardware
a) Description of
Locking Device:
2.4 Vent Opening ❑ Yes Lr No
4.3 Other Openings
3.0 Limitations SIZE 12'-2" X 15'-0"
4.4 Optional Graphic Illustration ❑ Yes ❑ No
' If yes, please allach drawings. If illustration is added, said
attachment must accompany this lorm.
5.0 Mandatory Tests
TEST
DESCRIPTION
TEST LOCATION
TEST DATE
TEST REPORT II
RTIFYING ENGINEER
6LICENSE NO.
ASTM E•330.84
Uniform Static
Air Pressure
N.C.T.L. ORLANDO,
FL. 210-0186-1
e>�Rai p PoRTJu°
PE 6z
If comparative analysis was used please Indicate Yes ❑ No
lTBSISI Re`j�vcw,"t 5 cvot.ivtd by C'ou.�
entalTM,.DESCRIPTION
y.
WTEST
IPTION
TEST LOCATION
TEST DATE
TEST REPORT r
CERTIFYING ENGINEER
8 LICENSE NO.
le
le
uauon
n Leakage
7.0 General Notes
8.1 Test reports are Dg) required to be submitted.
8.2 Application for building permit shall include (2) originals of this report, signed and sealed by a Prolasslonal Engineer, reviewed and
approved by the design professional of record.
8.3 Labels and identification shall be In accordance with the requirements of Section 3508.
8.4 All other provisions of the South Florida Building Code, Broward Edition, shall apply.
8.5 (') Tests are required If 1.1.1 is checked "yea"
8.0 Certification
9.0 Acknowledgement by Design Profoselonal of Record
9.1 To the best of my knowledge and ability the above garage door
conforms to the requirements of the South Florida Building Code.
Broward County Edition.
for wind pressures of =40 & -41.4 psf
Stela of Florida. Professional Engine.: or Registered Archiroci
based on comparative analysis. All door
components shall be the same as tested
door and DS glass panel size shall not exceed
3'- 4" X 2'- 0". Alum, panel thickness shall
Job/Silo Locaiion
be the me aS the tested door.
�/ •/\I r 5�
Not applicable to replacements less than $5.000 and in
compliance with Table 35•H see Section 104 and 302.2(b)(1).
rorrr. _ _ -
VipinN.Tolat,P.E. s 1197 National Certified Testing Laboratories test
F1.Reg. #12847, reports expire after a• four (4) year period.
*NOTE: Based o
pressure test re rt dated 05-22-9p, the overhead doo chieved a desY' n'`d'':'s`4r'
rating �i� ff
fastened to a wood,essbuckTheAOvgrhead door was testrec in 9
are to be calculated by a -1*-4: c0.ltional faG+o,,; ....._,___.the aabarator,i.-'Yh